Search Documents

By Marcel Laflamme, Sebastián Ibarra‑Gutiérrez

Improvement on controlling the stope limits has enabled the assessment of technical performance in several underground mining operations. Technical performance, integrated to stope geotechnical and geomorphological parameters, constitutes the basis which guides mining engineers in the Mineral Reserves Estimation process. Moreover, there are established definitions to report this information in Canada, incorporated in NI 43–101, which stipulates that “A Mineral Reserve includes diluting materials and allowances for losses that may occur when the material is mined” [1]. However, some loopholes have been identified regarding practical standards followed to specify the way to include and report ore losses when the lost material was blasted and must be left behind unrecovered inside the stope. In fact, general efforts to estimate and quantify the negative effects of operational ore losses only consider under-break ore loss. However, mining engineers frequently confront situations requesting the anticipated closure of a stope. Therefore, reconciliation process should reflect the amount of unrecovered Mineral Reserve. This work presents a discussion of possible practices to integrate adequately operational ore losses consisting of blasted but not recovered material and focuses on how different approaches regarding the material constitution could severely affect the stope technical performance interpretation.

Aug 9, 2021

By M. E. Poad

The Research and development review arrived too late to appear in the May issue. The competitiveness of the US mining industry in a world market depends on many factors. The introduction of new and innovative methods, though, can have a significant, long-term impact. As industry cuts back its own long- term research and development efforts, the federal government continues to provide the major support for mining and minerals research. The US Bureau of Mines works with the mining industry and the academic community to develop innovative concepts for the mining and processing of non-fuel minerals. The Bureau’s research focuses on exploration and mining technology, minerals and materials science, processing technology, health and safety and environmental technology. Mine design A conical caving system, being designed by the Bureau, would allow the development of low-grade ore bodies, early startup at lower initial capital costs and increased safety and versatility in development and production. This method is a form of mass caving that allows the ore to be drawn from a central loading point at the bottom of the cone- shaped caving zone (Fig. 1). A simulation laboratory model and computer analysis show initial promise for predicted performance. For tabular, flat-lying ore deposits, the Bureau is investigating a version of the Finnish slot-and-fill system. For this total extraction method, a pattern of rectangular panels is laid out. One panel is extracted in a series of parallel slots and is replaced by alternating-row pillars of backfill. After one panel is mined, equipment and operations are transferred to another panel. By transforming this rectangular layout to a curvilinear geometry, one continuous spiral can be mined without re positioning equipment. Instead of parallel slots and pillars aligned in a rectangle, the slots and pillars are arranged in a spiral.

Jan 1, 1992

By Paul Piercy

Bougainville Copper Limited operates a porphyry copper mine in Papua New Guinea. The waste dumps will contain 400 to 500 million tomes of rock at the end of nine life. The paper describes investigations carried out over a period of en years and highlights the problems associated with waste lump leaching in a tropical and seismic active region. Aspects discussed include mineralogy, chemical reaction, leaching rates, microbiological activity, dump stability, dump structures, effects of tropical conditions, seismic activity and topography.

Jan 1, 1981

By D. W. Horsfall

The washability of South African coals is described and the problems encountered in washing at low densities, to make premium products, are enumerated. The measures taken to overcome those problems, when low density separations became a commercial necessity, are described in detail. The descriptions of processes are with specific reference to the three sizes commonly treated separately in coal preparation namely coarse coal, small coal, and fine coal. Some information is given on the performance characteristics of the plants erected to meet market requirements.

Jan 1, 1995

By Samuel S. M. Chan

Rock surrounding mine openings frequently is an impermeable type such as shale or granite. Most rock, however, has joints, bedding planes, cleavage planes, or other potential discontinuities. Permeability to fluids (gas or liquid) may exist via natural joints or fractures in an otherwise impermeable rock. In the mining situation, tectonic and induced tensile and shear stresses may be great enough to cause joints to open or fractures to develop in previously solid rock. The rock, as a result, becomes less self-supporting and may - require artificial support such as rock bolts or timber. Simultaneously, as fractures develop, permeable paths may be created. If fluid can be injected into a previously solid and impermeable rock mass, a logical conclusion is that a fracture (crack) flow path must be transmitting that fluid. The U.S. Bureau of Mines Laramie (Wyo) Energy Research Center has been evaluating results of in-situ oil shale fracturing (hydraulic or explosive) and retorting experiments by. a fluid (air) injection , and borehole air flow profile logging technique since 1956 (1, 14, 15). In the oil shale case, it is imperative to know the location and flow capacity (permeability) of natural fractures, if they exist, and induced fractures that inter-connect vertical wellbores at depths of fifty to several hundred feet. By injecting air into one wellbore in a system of several wells and measuring input volume and pressure while simultaneously measuring the output of other wellbores, the minimum areal extent of interconnecting permeable fractures can be determined. Exact locations (depths) of fractures and individual fracture flow capacities between wellbores can be determined by air flow profile logging (14, 15). Knowledge of fracture locations and permeability is essential to rational experimental in-situ retorting design.

Jan 1, 1973

By Joaquin Ruiz

Although Mexico is known for its important base-and precious-metal deposits, and lately oil, some industrial minerals play an important role in the Mexican economy. Sulfur, the most important industrial mineral produced, accounts for approximately 7.5 percent of the total value of mineral production. This commodity is followed by fluorspar, which accounts for 6.4 percent. Predominantly, the fluorspar deposits are very high grade (75 percent CaF) and are contained in lower Cretaceous limestone in the states of Coahuila and San Luis Potosi. Base-metal deposits in the area of Parral (notably San Francisco del Oro), however, have become important fluorite producers in their own right. (San Francisco del Oro has 12 percent fluorite gangue.) Salt from the Guerrero Negro solar-evaporation ponds in Baja California account for 6 percent of the total shares; phosphate from Baja California also accounts for 6 percent. Barite from man to deposits in Lower Cretaceous limestone in Coahuila and exhalative deposits in the Paleozoic section of Sonora account for 1.0 percent. In addition, Mexico is an important producer of gypsum, graphite, and celestite. Although graphite and celestite are not large-scale operations and thus do not contribute much to the Mexican economy, the Mexican graphite and celestite deposits are among the most important in the world; Mexico is one of the world's few sources of celestite. The celestite is in the form of large, high-grade mantos in Cretaceous limestones in northern Mexico.

Jan 1, 1987

By J. Noll, D. Yantek, J. Organiscak

The Office of Mine Safety and Health Research of the U.S. National Institute for Occupational Safety and Health (NIOSH OMSHR) conducted laboratory testing of a self-tramming, remotely controlled mobile Dry Scrubber (DS) that J.H. Fletcher and Co. developed under a contract with NIOSH OMSHR to reduce the exposure of miners to airborne dust. The scrubber was found to average greater than 95 percent dust removal efficiency with disposable filters, and 88 and 90 percent, respectively, with optional washable filters in their prewash and post-wash test conditions. Although the washable filters can be reused, washing them generated personal and downstream respirable dust concentrations of 1.2 and 8.3 mg/m3, respectively, for a 10-min washing period. The scrubber’s velocity-pressure-regulated variablefrequency- drive fan maintained relatively consistent airflow near the targeted 1.42 and 4.25 m3/s (3,000 and 9,000 ft3/min) airflow rates during most of the laboratory dust testing until reaching its maximum 60-Hz fan motor frequency or horsepower rating at 2,610 Pa (10.5 in. w.g.) of filter differential pressure and 3.97 m3/s (8,420 ft3/min) of scrubber airflow quantity. Laboratory sound level measurements of the scrubber showed that the outlet side of the scrubber was noisier, and the loaded filters increased sound levels compared with clean filters at the same airflow quantities. With loaded filters, the scrubber reached a 90 dB(A) sound level at 2.83 m3/s (6,000 ft3/min) of scrubber airflow, indicating that miners should not be overexposed in relation to MSHA’s permissible exposure level — under Title 30 Code of Federal Regulations Part 62.101— of 90 dB(A) at or below this airflow quantity. The scrubber’s washable filters were not used during field-testing because of their lower respirable dust removal efficiency and the airborne dust generated by filter washing. Field-testing the scrubber with disposable filters at two underground coal mine sections showed that it could clean a portion of the section return air and provide dust reduction of about 50 percent at the face area downstream of the continuous-miner operation.

Jan 1, 2016

By John S. Jones, Ralph E. Brown

INTRODUCTION For more than a century, artificial ground freezing has been used for groundwater control and structural support for excavations. Most of the early uses of the freezing method were for sinking deep access shafts for mines and tunnels (1,2,3,4). More recently, ground freezing has increasingly been used for construction of large diameter cofferdams and soft-ground and mixed-face tunnels (5). Although ground freezing has been used in the past-for tunnels, it was invariably used as a last resort measure, where more conventional measures could not be used. The more recent freezing applications, however, have become increasingly cost competitive with more conventional techniques, and are now being included as part of the design concept (6,7,8,9,10,11,12). The purpose of this paper is to describe some of the more recent applications of ground freezing for tunnel construction. The paper begins with a brief description of the most commonly used freezing system, the Poetsch process. Recent tunneling projects utilizing ground freezing for structural support are then discussed. DESCRIPTION OF THE FREEZING METHOD The most commonly used freezing method is the Poetsch process, which was originally developed by F. H. Poetsch in the late 1800's. The system consists of a brine coolant, typically calcium chloride and water. Freezepipes are placed into boreholes or are

Jan 1, 1979

By Robert W. Miller

There are many problems faced by ventilation engineers in deep underground mining operations, not the least of which is controlling miner exposure to radon gas and its daughter products. Radon gas is commonly found in uranium mining operations, but may also be present in other deep metal mines. For example, tin mines in England, iron ore mines in Sweden, gold mines in South Africa, and molybdenum mines in the U. S. have potential radon exposures. This is because uranium and accompanying radium ore are ubiquitous to the earth's crust albeit at low levels. The fact that the activity represented by one WL can be caused by a relatively low concentration of radon gas increases the difficulty of control. Since the source of the radon gas is usually widespread throughout a mine, local exhaust ventilation is not a viable control schema. The technique used to control exposure is then dilution ventilation and, in fact, huge amounts of air must be moved in order to reduce potential exposures to an acceptable level. An interesting comparison can be made of ventilation rates in different types of mines. It is estimated in modern coal mines, which are generally acknowledged to have high rates of ventilation, that about eleven tons of air are moved for each ton of ore mined. A typical operating uranium mine may have ventilation flows of 14-15 tons per ton of ore mined. This provides an idea of the scope and importance of ventilation in modern mining operations where radon is a hazard. Further pressure is put on ventilation engineers by the steady downward trend in exposure limits set by national and international standard setting agencies. Much of this tendency toward lowered standards is based upon longitudinal mortality studies of miner populations. Another important factor is the limited number of experienced miners available in the labor pool. For optimum production, it is important to have as many experienced miners underground in each shift as possible. However, the average daily exposure in a U. S. mine must be less than .3 WL to permit the miner to work underground for a full year. The ventilation system then must provide enough uncontaminated air to maintain the WL below the .3 TTL level to maximize production efficiency and minimize personnel turnover and the problems associated with it. Ultimately, the goal of the ventilation engineer and health physicist is to protect the working miner from harmful exposures based upon currently acceptable standards. U. S. Federal regulations require that in uranium mines all active work sites must be monitored every two weeks if they measure above .1 WL. Areas that have .3 WL ratios or higher must be monitored on a weekly basis until five consecutive weekly samples show the level has dropped below .3 WL. Also, exposure records must be kept for all individuals exposed to levels exceeding .3 WL. These requirements provide a strong economic incentive to have a ventilation system that minimizes exposure of any personnel. A good ventilation system requires careful planning, operation and backup in order to fulfill its mission of providing adequate clean air. Its proper operation also requires coordination with production personnel so it can be adapted as new areas in the mine open up and old areas are sealed off. The ultimate indicator of ventilation efficiency to control radon daughter exposure is, of course, monitoring working levels. Historically, this has been done using the Kusnetz, Tsivoglou, and Rolle's methods, among others. These methods all require cumbersome equipment and tedious calculations to obtain the measurements that results in WL. More important, however, they require a significant time lag between sampling and counting, typically 40-90 minutes. This time lag is, in fact, what can cause significant economic losses due to unnecessary downtime as well as high WL exposures. In a typical mining situation, a sampling technician using the Kusnetz method takes a sample, moves to the next location and takes another sample and so on. Forty to ninety minutes after the first sample, the technician will stop, run the activity count on the filter and calculate the WL. The technician may be one-half mile away or several levels removed from where the first sample was taken when it is counted. If the WL ratio is high the technician must then backtrack to the sample position. There are then two options. If the sample area is a working stage, it can be shut down or a second sample can be taken. If the first alternative is chosen; i.e., shutdown and correction of the ventilation, then another sample must be taken, followed by a forty minute wait for results. If the ventilation adjustment didn't correct the problem, then the whole process must be repeated with a minimum of forty-five minutes per sample cycle when using the Kusnetz method. It has been estimated from operating uranium mines that the cost per hour for downtime on a production slope is about $1,50O/hour. The time lag between sampling and resultant data can be very costly. If the second alternative is chosen to verify the first reading, the miners may be unnecessarily exposed to high levels while waiting for the result. Clearly, such a sampling system can be markedly improved by eliminating the excessive time lag between sampling and analysis.

Jan 1, 1981

By Y. Astafyev

Autotransport is one of the most conventional kinds of transport in iron ore open-pits. It. is successfully used both independently and in combination with other kinds of transport. In the Krtvoy Rog Basin open-pits annual truck transportation accounts for more than 235 million tons of ore and waste rock. In the process of operation trucks make up various transport streams depending on - the development of autoroads in the open-pits; - the capacity and the number of loading equipment ; - the load carrying capacity and the speed characteristics of trucks

Jan 1, 1979

By Stephen Day, Maria Falutsu, Gary Coulter

Open-pit mining began at Red Dog in 1989. Mining is expected to continue past 2030 but closure planning is an ongoing process. Geochemical studies of rock and tailings were begun in 1996 as part of development of closure plans to address leaching of metals and ARD. The deposit has many different primary and secondary sulfur minerals in amounts that preclude the use of conventional geochemical characterization methods. This paper will describe development of a specific chemical method to estimate the speciation of sulfur and classify wastes according to reactivity.

Jan 1, 2000

By L. P. James, W. W. Atkinson

Utah has produced about 31.7 kt (1 billion oz) of silver, more than any state in the United States except Idaho. Several high-grade ore systems in Utah, where the mines are now closed, occur within large polymetallic limestone-hosted districts related to plutonic complexes. These mines fed several major lead smelters for nearly a century. Interaction of magmatic chloride-rich fluids with carbonate rocks localized significant bonanzas within these districts. A low sulfidation state was produced in the fluids by their passage through limestones. The Bingham openpit mine has also yielded more byproduct silver than other porphyry copper-molybdenum-gold systems. Away from exposed intrusive rocks, some large silver-only systems occur in Mesozoic sandstone and in caldera-related veins in volcaniclastic rocks. Thick permeable latest-Proterozoic basement metaquartzite sequences present beneath western Utah may have been important, as perhaps they were in the Coeur d'Alene district of Idaho, in providing chloride and silver-rich ore fluids. However, it is clear that specific Tertiary magmatic events played an essential role in the evolution of the Utah silver-rich metallogenic province. The largest silver districts in the state are genetically related to Tertiary porphyritic plutonic rocks.

Jan 1, 2003

By M. Frenzel, D. Ebert, K. Bachmann, A. D. Renno, R. Möckel, J. Gutzmer, J. Krause

With the increasing demand for metalliferous and mineral raw materials, and consequent depletion of the global natural resource base, the possible utilization of secondary raw material sources is receiving more and more attention. In the present study, we present results from a detailed vanadium deportment study of three basic oxygen furnace slag (BOS) samples known to containing elevated bulk concentrations of vanadium (V). Complementary analytical methods that were used to quantify the abundance and composition of V-containing phases include SEM-based automated mineralogy, Xray fluorescence (XRF) analysis, and X-ray powder diffraction as well as electron probe microanalysis. The vanadium deportment was quantified using Monte-Carlo simulations of the data obtained from automated mineralogy and electron microprobe analysis. The total V concentrations identified by XRF are between 1.7 and 2.2 weight percent V. The most important hosts of vanadium are larnite-, brownmillerite- and portlandite-solid solutions. In two samples, calcium carbonates also significantly contribute to the V deportment, while wuestite, lime and native iron do not contribute significantly to the vanadium deportment. A thorough consistency check identifies considerable uncertainties in the density of the Vbearing phases as the most likely reason to explain remaining discrepancies between measured and calculated V values.

Aug 1, 2024

By T. W. West

A description of a coal washing spiral is presented, together with a discussion of the parameters which define the envelope within which the spiral can be successfully applied. The correct process engineering, installation, operating and maintenance parameters are addressed as well as actual results for new and retrofit installations on USA coal capital and operating costs of spiral circuits are compared to those of traditional fine coal circuitry.

Jan 1, 1988

By Andrew H. Stearn, Robert O. Agbede, Edward F. Divers

The ability to compete profitably in a competitive, demanding and specialized market, requires all components of productivity to be optimized toward the same manufacturing goal. This ever present requisite is seldom more apparent than with the quality control (PC) considerations that confront the super-refined metallurgical production necessary for today's exacting technical applications. In a work-place that already exceeds all environmental standards for cleanliness, this paper describes the development of specific environmental mechanisms and controls implemented at a titanium processing facility to impact both the minimal air-borne particulate contaminants and excessive process heat generation which are believed to degrade product purity. Based on the analysis of a carefully structured and instrumented field survey, two alternative solutions were proposed to modify the present facility utilizing a forced air (blowing) system. The first scenario requires ambient air to be drawn from a louvered rooftop installation and ducted to specific zones within the plant with appropriate weighted louvers and wall and roof exhausters designed into the system for air control. The second scenario incorporates a properly sized baghouse to be used in conjunction with the first system.

Jan 1, 1991

By M. Quamrul Ahsan, Andrew Griffiths, Edward P. Jucevic

Heap leaching of precious metal ores using the cyanide process is extensively used in the Western U.S.A. for extracting gold. Consequently, the impact of cyanide in the spent heap is closely examined by environmental agencies and permitting authorities. Currently, many states require that all decomnissioned heaps be detoxified before abandonment. This paper describes a case study for detoxification of spent heaps at the ACH-Dayton Project using hydrogen peroxide. The chemistry of cyanide detoxification by hydrogen peroxide, together with simplicity of a detoxification operation, is discussed.

Jan 1, 1989

By F. G. Crack

This paper is based on the philosophy that the management structure and strategy required for mine construction and development projects are different from that required for routine production and maintenance operations in a mine. The purpose of this paper is to present an integrated approach to the management of mine development projects. This paper highlights the four major aspects of the integrated approach. First, a brief review of the various types of contract documents is provided. Second, the management organization of a project is discussed. Third, the project manager's role and the field supervisor's responsibility are briefly outlined. Finally, the use of scientific techniques for planning, scheduling, executing, and controlling projects is presented. Each of these aspects is important; however, each by itself cannot be expected to bring order or unifying impact to the complexities involved in overall project management. When all these aspects are coordinated, the result will be a sore successful project from conception to completion.

Jan 1, 1982

By T. L. Conley, J. J. Rozek

The $2 billion (A$) Melbourne City Link Project is one of the largest and most important metropolitan road developments ever undertaken in Australia. The project involves two three-lane vehicular tunnels totaling 5 km, constructed as deep as 65 m underground. The 3.4 km Burnley tunnel is one of the world's longest three-lane tunnels. The project is being delivered under a DBOOT [design-build-own-operate-transfer] process and all design and construction is performed to ISO 9000 standards. Tunnel excavation began in May 1996, and the tunnel will open to traffic in 1999. This paper focuses on the range of construction techniques utilized during construction.

Jan 1, 1999

By James R. Aggson, Verne E. Hooker, Dennis R. Dolinar

The stability of underground openings and mining systems is closely related to the in situ stress field. This paper presents a short discussion of the three-component borehole deformation gage and overcoring technique which the Bureau of Mines uses to measure in situ stresses, and a summary of stress data that the Bureau has gathered in the process of evaluating ground control problems. Specific ground control problems and stress distributions are discussed as examples.

Jan 1, 1982

By Kal V. S. Sastry, Stephen N. Little

Computer simulation of comminution systems is found to provide significant cost savings by enabling efficient circuit design and development of control systems. These simulation systems are based on sound mathematical models and numerical methods. Nevertheless, they are found to be hard-to-use and hard-to-modify to carry out more elaborate process analysis. This paper discusses the fundamental principles and practical aspects of an advanced, highly functional, and user-friendly SIMulator for COMminution, SIMCOM, that is being developed at Berkeley by incorporating state-of-the-art software engineering principles.

Jan 1, 1992