Search Documents

By M. C. Baumann

The Getchell Mine is located in Humboldt County, Nevada, approximately 70 km northeast of Winnemucca. Slope management has been a critical factor in the feasibility of mining operations since they began in the early 1930's. Although underground entries began in 1937, underground production was limited because hanging walls consisting of clay gouge and crushed rock tended to collapse into the workings. Controlling these collapses required extensive timbering. Due to these poor ground conditions, surface open-pit mining was the primary mode of production from 1938 to 1967 with only minor contributions from underground operations. Mining was suspended in 1967 due to economic pressures. From 1960 to 1967, the previous operator mined the property in three open pits. Initially, these pits were constructed with footwall benches, but these failed. These failures were aggravated by construction of 60° slopes in footwalls with shale partings dipping into the pit at 43° to 60°, resulting in large planar failures and wedge failures. In response, the previous operator adopted a slope parallel to the bedding planes.

Jan 1, 1993

By S. Usui

In a previous article1 the methyl stretching vibrations for a series of xanthates and amines were reported, and the frequency of the methyl stretching vibrations in a homologous series of the alkyl compounds were shown to decrease exponentially with chain length and approach a limiting value corresponding to that of saturated hydrocarbon beyond six or seven carbons. These observations were explained quantitatively by the theory of Goto and Takenaka2 who proposed an equation relating the frequency shifts to the inductive effect of polar groups. As a result, the alkyl groups in the shorter chain heteropolar compounds were interpreted as becoming somewhat polar, and a good correlation was observed between the CH3-stretching frequencies and such surface chemistry parameters as contact angle, surface tension lowering, solubility, and critical micelle concentration" The substitution of fluorine atoms, the most electronegative of all atoms, for the hydrogen atoms in alkyl groups was expected to reverse the direction of the inductive effect within a heteropolar molecule, and its effect on the C-F stretching frequency shifts and on some surface chemical properties became of interest. In a recent study the C-F stretching frequencies of a series of normal perfluorocarboxylic acids and a few 1,1' -dihydroperfluoro alcohols were determined as a function of chain length and the results were compared with the corresponding hydrocarbon analogs. Furthermore, the nature of the induced polarity in the hydrocarbon and fluorocarbon groups was investigated through surface potential measurements at the interfaces of air-aqueous solutions of normal butyl alcohol and of l,l'-dihydroperfluorobutyl alcohol and through differential capacity and electrocapillary measurements at the interfaces of mercury-aqueous solutions containing the above two alcohols. Experimental Normal perfluorocarboxylic acids and 1,1' -dihydroperfluoro alcohols were provided through the courtesy of the 3M Company, St. Paul, Minnesota. Normal butyl alcohol was purchased from Distillation Product Industries, Rochester, New York. A Perkin-Elmer Model 621 infrared spectrophotometer was used to investigate the spectra in the frequency region of 1200 to 1270 cm-l with frequency scale

Jan 1, 1971

By Stephen P. E. Redmond

A 15 km water supply tunnel is being constructed in Buenos Aires, Argentinata expand the capacity of the existing system. Two 4.3 meter diameter Earth Pressure Balance (EPB) tunneling machines operating at times from the same shaft on a congested work site and advancing through sedimentary deposits underlying this wonderful city pose interesting challenges. As of January 1999approximately 50% of the tunnel has been excavated. Combined machine production rates of 1026 m/month have been achieved. Presentations made in prior proceedings can be referenced for details of the overall Project scope and for details of the tendering process. The purpose of this paper is to compliment those presentations by addressing now the execution of the work.

Jan 1, 1999

By G. Robert Guillet

Nepheline syenite is a light-colored feldspathic rock that is used primarily as an addition to the glass batch. It is also used in ceramics and as an industrial filler. Composed essentially of the soda and potash feldspars and nepheline, nepheline syenite contributes needed alkalis and alumina to the glass composition. And because it contains a higher proportion of these oxides per unit weight, it is a formidable competitor for feldspar in northeastern North America and parts of western Europe. Nepheline-bearing rocks are not uncommon on a world scale, but few are able to be beneficiated to a composition sufficiently low in iron to be used in the making of glass. Nepheline can only form in an environment deficient in silica. Hence free silica, as quartz, is always absent in the primary mineral assemblage. Biotite, hornblende and magnetite are usually present as minor accessory minerals, and zircon, garnet, muscovite, and apatite may be present as trace minerals. Nepheline syenite is produced for glass, ceramics, and filler markets by Unimin Canada Limited at Blue Mountain, in south- eastern Ontario. Unimin acquired the former Indusmin and IMC properties from Falconbridge Ltd. in 1990. Elkem Nefelin AIS commenced production of similar products from Stjernoy Island in northern Norway in 1961. Unimin acquired this company in 1992. Nepheline has also been a byproduct of apatite mining on the Kola Peninsula for many years, and in 1951 the production of alumina from nepheline was commenced in a plant near St. Petersburg (Leningrad). There are now four plants in the Russian Republic, two smaller ones based on nepheline tailings from apatite mining and two larger and more recent plants in central Siberia using other nepheline resources. All four of these plants are integrated complexes that produce alumina for the subsequent production of aluminum metal, sodium and potassium carbonates, and portland cement. Roofing granules are produced by the 3M Company from a nepheline rock in Arkansas. In 1980 and 1989, trial shipments of nepheline syenite were recorded from new sources in Brazil and western Turkey respectively. Recent interest is also recorded for deposits in China, Saudi Arabia, and British Columbia.

Jan 1, 1994

By M. Misra

The dispersion of oily collector has significant effect on the flotation recovery of ultrafine coal. Generally, reagent dispersion is accomplished by mechanical mixing and/or ultrasonic agitation, followed by direct addition of dispersed collector into the flotation cell. However, such dispersion and reagent addition techniques are invariably inadequate and non-selective. A new collector utilization technique involving gas phase transport of atomized collector has shown improved results when compared to conventional reagent addition techniques. This new technique involves atomization of the collector into the gas stream. Under these circumstances an aerosol is introduced into the flotation cell. Initially, the oil is dispersed within the gas phase (continuous with respect to oil) and the gas phase is dispersed within the pulp (continuous with respect to aerosol). In the flotation cell, the atomized oil droplets coalesce on the bubble's surface and create a de-facto oil-encapsulated bubble. This approach provides excellent dispersion, increases selectivity, and most significantly increases the flotation rate of ultrafine coal. Furthermore, atomization of collector/frother combinations yielded improved flotation yields and maintained near uniform froth levels which is a desirable feature in coal flotation. In addition to flotation experiments, microscopic examinations of the attachment of oil-coated bubbles at a coal surface were conducted by attachment-time and contact-angle measurements. The oil coated bubbles attach at significantly faster rates and with a higher contact angle than do oil free bubbles.

Jan 1, 1987

By Haydn H. Murray

A hydrothermal bentonite located in the high Sierras in Nevada is being mined and processed to produce a natural dietary supplement. The minerals present are smectite, gypsum, jarosite, quartz, feldspar, kaolinite, goethite, hematite and zeolite. The clay material was analyzed for respirable crystalline silica, asbestiform minerals, heavy metals and dioxin. No asbestiform minerals are present and the crystalline silica, heavy metals and dioxin are all less than the maximums set by Federal and State agencies. The clay material was analyzed chemically for all major, minor, trace and rare earth elements. The geology, applications and analyses will be discussed in the paper.

Jan 1, 2005

"The seventh annual Mineral & Metallurgical Processing Division (MPD) student poster contest was held last February at the SME Annual Conference & Expo in Phoenix, AZ. A total of 21 students entered the poster competition. The students were required to submit one-page abstracts, which were reviewed by the judges, after which they prepared posters to display their work. A panel of judges went to each student and listened as the student explained his/her research in five minutes.The students worked hard at their research and then set aside time to complete all the necessary steps to enter the competition. Recognizing the effort required to participate, the MPD provided monetary rewards to all participants. First place received $1,000; second, $500; and third through seventh, $200. All remaining entrants received $100 each. The winners have their abstracts published in this issue of Mining & Metallurgical Processing. As in past years, there were separate levels of competition for undergraduates and graduates.Now for the winners:Graduate winnersJoseph Halt won first place for research on the use of additives to starch binders to create iron ore pellets. Vivek Agarwal received second for working on using solvent extraction to concentrate lanthanum. Jordan Rutledge placed third for utilizing tannins to depress calcite in fluorite flotation. Fourth through seventh places were Vu Truong, Jacob McDonald, Hunter Sceats and Doug Schriner.Undergraduate winnersLaura Nugent won first place for using high-frame-rate cameras to follow bubbles as they moved from the pulp to the froth in flotation cells. Taylor Graham earned a second-place finish by researching how to acid leach low-grade manganese carbonate.Although its cliché to say everyone’s a winner, everyone can benefit from attending the MPD Student Poster contest. All the students were able to display their work to potential future employers, and industry professionals could talk to the up-and-coming engineers. Next year, there will be another competition for more posters and networking, so get ready to attend.Thank you to all the students for participating; Lisa Schlink for chairing the session; the judges, Aaron Noble, Debra Switzer, Mohammad Rezaee, Nick Gow and Ren Bryce, for evaluating the abstracts and posters; and the MPD sponsors for supporting the competition. This has only been successful with the input of all three groups. Engineering iron ore pellets to reduce their dustinessJ.A. Halt and S.K. KawatraGraduate student and professor and chair, respectively, Department of Chemical Engineering,Michigan Technological University, Houghton, MI, USAIntroductionIron ore pellets are hard spheres made by agglomerating iron ore concentrate and binders. Pellets are the preferred ironbearing feed for blast furnace ironmaking. Starch has been proposed as a binder because it has good adhesive properties, does not contaminate pellets and is relatively cheap. However, starch binders typically lead to weak pellets with rough surfaces, and these can cause high levels of dust within process equipment and when pellets are handled and shipped (Halt and Kawatra, 2014). Our research shows that by adding a small quantity of other additives, pellets made with starch binders become smooth and strong. The newly designed binder leads to significantly lower levels of fines when pellets are handled."

Jan 1, 2016

By D. J. Collins

While the charcoal in pulp (CIP) process was introduced to the mining industry many years earlier, it did not gain widespread recognition until 1973 when Homes take Mining Company installed a CIP circuit at their Lead, South Dakota plant. Since then, a number of mills have been put into production which utilizes activated charcoal for the recovery of precious metals. One of these plants was the Jerritt Canyon mill which Freeport Gold Company commissioned in 1981. It was during the time that the author was employed by Freeport Gold Company that the ideas and concepts presented in this paper were formulated.

Jan 1, 1989

By Florence Munter

This paper provides a discussion of the various federal and state laws governing water quality as related to mining operations. The specific laws addressed are the Clean Water Act, and the Arizona Mined Land Reclamation Act. Topics that will be addressed are mine water and process water discharges, storm water discharges, pollution prevention, dredge and fill, spill prevention control and countermeasure plan, and surface water protection. Proposed changes to the laws and regulations will be discussed. Compliance strategies will be suggested to prevent potential noncompliance and enforcement.

Jan 1, 1996

By Barry J. Hansen, Ruston A. Ford

Production of mine backfill from the tailings produced in a proposed Crandon concentrator is described. A process has been developed capable of producing suitable fill for the mining method selected for the Crandon orebody. It maximizes the placement of pyrite underground as fill and segregates tailings into pyrite and nonsulfide fractions. To determine the suitability and engineering characteristics of the backfill product for use underground, laboratory and physical stope simulation model testing was conducted. The results of the testing and the application of those results to the design of the backfill system ultimately affecting mine geometry and subsequent mine production will be presented.

Jan 1, 1981

By Andy Thompson, Frank Perrone

"As part of the Metropolitan Transportation Authority’s $10.5bn East Side Access Project in New York, 3,200 m of tunnel had to be constructed in rock, mix face and soft ground conditions beneath one of the largest passenger railroad junctions in North America, handling over 780 trains per day. The use of risk based decision making tools was essential in developing the bespoke contract framework that was adopted as well as making informed decisions once excavation commenced. This paper will outline the risk management process adopted, discuss the risks and mitigation strategies adopted and comment on the impacts of this approach on the as built Project cost and schedule. In particular, the paper will outline the unique approach used to establish the baseline against which the Contractors performance would be measured as the selection of a Slurry TBM to excavate the tunnels was considered to compromise the effective use of a Geotechnical Baseline Report. BACKGROUND AND CHALLENGES Contract CQ031, Queens bored Tunnels and Structures was awarded in September 2009 to a joint venture of Granite Northeast/Traylor Brothers/Frontier Kemper (GTF JV) for $717.6m following a negotiated procurement process. A robust approach was taken with regard to the management and payment for risks associated with the construction of these tunnels. Risk assessments were carried out during the design phase and a risk register was developed prior to procurement. During the procurement phase close attention was paid to ensuring that the allocation and pricing of known risks, together with mechanisms for managing future risks were clearly defined between the MTA and GTF JV.In comparison to the excavation work in Manhattan, which was performed in competent hard Manhattan schist, the tunnels in Queens were excavated predominantly through soft ground with a high water table and complex environmental conditions. Not only did this require the use of pressurized face TBM technology, a first in New York, but also a re-evaluation of the contractual mechanisms used to manage the hard rock excavation contracts for their appropriateness to the soft ground tunnel work."

Jan 1, 2016

By G. J. Hodges

The Stillwater Mining Company, a partnership of Pittsburg & Midway Coal Mining Co. and Manville Corporation, operates a precious metals smelter at Columbus, Montana to further up-grade concentrates from its platinum/palladium mine. The smelter began operation in the summer of 1990. The gas cleaning system in the facility utilizes "oxidation/dilute mode" dual-alkali scrubbing technology to capture sulfur oxide gases from the process gas streams. This paper describes the rationale for selecting the dilute mode dual-alkali system and summarizes design parameters. Start-up problems and their solutions are also discussed.

Jan 1, 1992

By Y. J. Wang

The Hardy Cross iterative method is the most popular technique for solving a ventilation network problem with natural air splitting. This method tradition-ally solves each mesh equation by an approximation during each iteration. It is thus interesting from both theoretical and computational viewpoints to be able to solve for an exact solution to the mesh equation. Presented in this paper is an algorithm for computing the exact solution to the mesh equation with a variable fan pressure. The algorithm uses signum functions for air quantities to generate an alternative mesh equation in the form of a quadratic equation, which has two solutions defined by the well-known quadratic formula. The condition that the derivatives of the alternative and the original equations must be the same provides a basis for the correct choice between the two solutions.

Jan 1, 1997

By L. E. Garner

Aggregate resources should be considered primary factors in urban development. Resource planning is essential because land values, previous construction, or zoning restrictions often preempt exploitation of aggregate deposits within an urban area. Sequential land use practices allow development of areas prior to urban development. Population and aggregate consumption trends in Austin, Texas, indicate that substantial quantities of reserves will be lost to future development. Aggregate materials are present in nearby seas. However, a comparison of transportation and reclamation costs indicates that reclaiming land after mineral extraction can be significantly cheaper than transporting materials longer distances.

Jan 1, 1979

By Robert M. Becker

The evaluation of in situ rock stresses from measurements of the change in diameter of a borehole that is stress-relieved by overcoring has become a common practice. Generally the stress evaluation has been based on isotropic relations whereas rock in varying degrees is anisotropic. A plane elasticity solution for a circular hole along one axis of an orthotropic medium has been adapted to evaluation of in situ stress. The necessary elastic parameters for this evaluation may conveniently be obtained from static tests on the overcore in conjunction with a consistent orthotropic thick-wall cylinder solution. The method and equations for the laboratory and field evaluations are summarized and illustrated.

Jan 1, 1968

By N. Rajmohan, K. T. Jacob

Presented is a thermodynamic feasibility analysis of extracting base metal chlorides from low-grade, multi-metallic oxide ores using CaC[1]2 as a chlorinating agent in the presence of SO2 and O2. The oxides react to form corresponding chlorides, while CaC[1]2 is converted to CaSO4. The Ellingham diagram is used for comparing the standard Gibbs' free energy change for the sulfation-chlorination reaction of a large number of oxides. Except for alumina, silica and chromia, most of the other metal oxides will be converted to their respective chlorides. The volatile chlorides can be condensed, and the chlorides present in the condensed state can be leached. A process is proposed that uses a nontoxic chlorinating agent and gives an efficient separation of the metallic values from the gangue.

Jan 1, 1993

The National Mining Hall of Fame and Museum will hold its Ninth Annual Induction Banquet Sept. 8, 1996, at the Las Vegas Hilton Hotel. Six mining greats, two of them living, will be enshrined at the event. They will join 126 other mining legends previously honored by the hall of fame. The keynote speaker will be William Perry Pendley, president and chief legal officer of Mountain States Legal Foundation in Denver, CO. Jeffrey Zelms, president and chief executive officer of The Doe Run Co., will be master of ceremonies. Richard Swayne, regional director USA for Boart Longyear Co. of Salt Lake City, UT, will introduce the speakers. Thomas Falkie, president of Berwind Natural Resources Corp. and chairman of the Mining Hall of Fame’s board of governors, will enshrine the inductees.

Jan 1, 1996

By D. W. Frommer

In continuing its long range studies of methods of treating low-grade iron ores, the Bureau of Mines has developed a new selective flocculation, desliming, and flotation procedure that enables effective beneficiation of the finely disseminated ferruginous jaspers of the Marquette range, Mich. The process, developed on a bench scale and later confirmed in the 800-lb/hr pilot plant, comprises dispersion, selective flocculation, desliming to reject fine silica and clay, and flotation of silica from the remainder of minus 400-mesh pulps. Pilot plant flotation of two Marquette range ores, using the selective flocculation procedure on feeds containing 36 percent Fe, yielded iron recoveries of about 84 percent in concentrates containing 65 to 66 percent Fe and 4 to 5 percent silica. These results were metallurgically superior to those obtained when selective flocculation was not used. Also operating characteristics were better, and reagent costs were lower.

Jan 1, 1964

By H. H. Hughes, J. G. Dunn, P. G. Fernandez, H. G. Linge

Dissolved Arsenic (As) is stabilised primarily as As(III) and As(V) and enters ground water streams from sources such as the increasing metallurgical processing of As - containing ores [1]. As(III) is more toxic than As(V) and is less effectively removed from solution by oxide precipitation. Even for dilute As(III) solutions, skin contact or ingestion can cause dermatitis or cancer and there are stringent effluent control standards in place for As containing effluent from mining operations [2]. Chemtronics (Perth, Australia) has manufactured a compact digital voltamme­ter, based on anodic stripping voltammetry (ASV) and suitable for use in the laboratory or field. In this paper we demonstrate the utility of this equipment for measuring As(III) concentration with a detection limit of ca. 10 ppb.

Jan 1, 1995

By William F. White

It is a pleasure to have the opportunity of being here today to discuss the application of horizontal filters in the metallurgical industries. The use of horizontal type filters has been limited in metallurgical plants. However, in the recent past there have been new designs of this type equipment which greatly broaden their field of application. Through their use in many applications, important economies can be achieved over more conventional methods. The first of the modern continuous horizontal filters was initially developed by Oliver United Filters as their scroll type horizontal filter. This was an outgrowth of the old Oliver Sand Table that was limited to very coarse, free filtering pulps containing no appreciable amount of fine particles. The sand table was rather limited in application. The later continuous scroll type horizontal filter provided for a reverse air blow after discharge which reslurried the heel remaining and permitted the filtration of pulps containing finer particles. In the manufacture of phosphoric acid by the ?wet? process, the filtration of gypsum from the strong acid presented an extremely difficult filtration problem due to blinding of the filter media caused by crystallization of the soluble salts contained in the acid. A filter which allowed for continuous cloth washing was required, and this led to the development of the continuous pan type, and travelling belt type horizontal filters which provided for this need. Among the filters developed were the Prayon by Engineering and Industrial Corporation of Luxembomg for use in their phosphoric acid plants. They are one of the largest manufacturers of phosphoric acid in Europe. The Dorr-Oliver Traveling Pan Filter was also developed by Mario Giorgini, Manager of Dorr-Oliver?s Italian subsidiary, for use with the Dorr Company?s phosphoric acid process. Basically, there are four existing types of horizontal filters in commercial use at this time: The scroll discharge non-pan type, the continuous belt type (Lurgi), rotary pan type, and the traveling belt type. The construction and principle of operation of these various filters will be discussed.

Jan 1, 1958