Search Documents

By T. J. Batchler

"INTRODUCTION A variety of standing supports are being applied in underground coal mining operations to assist in providing stable mine entries. Standing support performance requirements depend on the nature of the ground deformation behavior, and therefore require a good understanding of the interaction between the support and ground to achieve an optimum roof support system. Mining operations often employ standing support strategies that are unique to their mine. A support system that functions successfully in one situation could fail in another situation. It is important that the design and installation of the standing support systems provide the highest probability of preventing roof falls. Considerable research and development has been conducted by support manufacturers to develop standing support technologies for the mining industry. The National Institute for Occupational Safety and Health (NIOSH) researchers, with the cooperation of various support manufacturers, have developed a testing protocol that evaluates performance characteristics of these standing support systems.. Using this protocol, each of these support systems has gone through rigorous safety performance testing under controlled loading conditions in NIOSH’s Mine Roof Simulator (MRS). It is important to understand the unique performance characteristics of each type of standing support. This information allows mine operators to determine if the support system is compatible with the conditions in the mine and to compare each support system and determine if that support will provide equivalent or improved support capability. This paper provides a comprehensive summary of support performance to facilitate this objective. SUPPORT DESIGN CRITERIA AND THE GROUND REACTION CURVE Standing roof support systems are designed to prevent unplanned roof falls. The selection of the standing support is based on the interaction of the support with the surrounding rock mass, and its function is to assist the primary support system in maintaining the integrity of the immediate roof. The standing support works to control the immediate roof structure by resisting deformation that contribute to delamination of the bedded layers and displacements that lead to separation of the bolted zone from stable roof structures above the bolted horizon (Barczak, 2005). Standing supports should be installed early enough and develop sufficient capacity to bring deformation of the ground into equilibrium before a critical deformation is reached that leads to a detached block condition, at which point the standing support will be required to carry the entire dead weight of the detached rock mass to prevent a roof fall from occurring (Mucho, 1999). The ground reaction curve (GRC) can be used to assist in determining the compatibility and design requirements for a support system. It is important to understand the significance of the ground reaction relative to the support design requirements. The ultimate objective is to match the support behavior to the ground response and create equilibrium (stability) of the rock mass. This equilibrium is accomplished when the support loading intersects the ground reaction curve (Figure 1). Essentially, the ground reaction concept implies that the convergence in the mine entry is controlled by the magnitude of the support resistance. However, as a passive support, the standing support develops its loading through convergence. As such, the support needs to maintain its load capacity through the associated deformation of the ground and resulting entry convergence until the equilibrium condition is reached. This requirement causes factors such as the support stiffness, peak capacity, yielding characteristics, and stability to be fundamental to proper support design and application. NIOSH contributes to providing this understanding through full-scale performance testing of support products in the Mine Roof Simulator."

Jan 1, 2017

By G. R. Erdman

The industrial mineral filler plant of the Gouverneur Tale Company is equipped with a good dust collection system installed long before the recent popularization of environmental pollution. Credit for this fact is due to the foresight of Mr. R. S. McClellan, Project Manager and subsequent Vice President and General Manager of Gouverneur Talc, who recently retired as Vice President Engineering of the parent organization, the R. T. Vanderbilt Company. Also instrumental in the early stages of plant operation and the solution of start-up problems was J. A. Gustin who is now an engineering consultant located in Martinsville, Va. Credit is most certainly due to the late R. T. Vanderbilt, the company's founder, who favored and approved the investment in the necessary facilities that were far ahead of all competitors in the industry at that time.

Jan 1, 1972

By M. Gobla

"Since 1994 the Bureau of Reclamation has used risk analysis to evaluate dams. Risk considers both the likelihood of failure and the expected consequences should failure occur. Risk analysis relies on the detailed formulation and critical analysis of all possible potential failure modes. Potential failure modes are formulated by describing the sequence of events that must occur to result in failure, where failure is defined as the uncontrolled release of the impounded reservoir. Failure occurs in response to loadings such as water seepage through a dam (static forces), shaking from an earthquake (dynamic forces), sudden flood inflows (hydrologic forces), or accidental overfilling (operational errors). Reclamation has applied risk analysis methods to inactive and abandoned mines to evaluate tailings dams and flooded underground mines. Case histories of potential failure mode analysis as applied to mine impounded water illustrates what critical technical information is needed to determine if failure is likely, what the consequences of failure are likely to be, and what are the highest risks that should be addressed first. INTRODUCTION Impounded water, and high water content wastes, at mining and industrial processing sites are potential threats to public safety and the environment. Recent failures such as the TVA Kingston flyash impoundment failure in Tennessee in 2008 (5.4 million yd3 released), the Mt Poly Tailings Dam failure in British Columbia in 2014 (5.8 million yd3 released), and the Smarco Fundao Tailings Dam failure in Brazil in 2015 (78 million yd3 released) has renewed attention to this issue. Potential risks from impounded water at mining and industrial sites originates not only from tailing dams, but also from water in process ponds and conveyance pipelines, sediment retention dams, water retention dams, mine pit lakes, and flooded underground mine workings. Conventional water retaining dams also have a record of failure. Notable examples of failure include Vajont Dam in Italy in 1963 (2,600 lives lost), Banqiao and Shimantan Dams in China in 1975 (171,000 lives lost), and Machhu-II Dam in India (10,000 lives lost). After the 1976 Teton Dam failure in Idaho, the Bureau of Reclamation (BOR) established a Dam Safety Program. By 1984 the agency developed and began using risk analysis methods. Reclamation operates and maintains an inventory of hundreds of aging dams which were designed and constructed over a period of one hundred years. Many of these facilities were constructed using engineering design and construction methods which would not be considered good practice according to present day standards. Diligent observational monitoring, detailed site investigations, and the application of risk evaluation to the BOR dam inventory has identified many deficiencies resulting in significant demands on available funding for remediation efforts. The application of risk analysis has allowed the agency to rank sites by risk. By giving priority of remedial efforts to high risk sites, significant improvements to dam safety have been achieved. BOR has also applied risk analysis to evaluate and reclaim inactive and abandoned mining and industrial sites. The application of risk analysis methods in the mining industry is not new, the methodology was transferred to the mining industry more than 15 years ago as discussed in ICOLD Bulleting 121 (ICOLD, 2001), yet failures persist. This paper is meant to convey the lessons learned from BOR’s use of risk analyses in its work on mine sites."

Jan 1, 2017

By Homer S. Anderson

To clarify what r mean about this long title, I would like to define the term technology. A standard definition of the word "technology" is "a technical method of achieving a practical purpose". Incidently, another definition of the term is merely "technical language". The same dictionary defines the word "technology" as "having a special, usually practical, knowledge of mechanical or scientific subject." Naturally, the practical purpose of the subject with which we are concerned is solving of problems we encounter in the mining industry. I might further describe the subject of this discourse by defining the term "manager". An old definition, "one who dispenses the duties of his position with care and economy." In line with the above definition most of the technology with which we in the mining industry are confronted with deals with some form of cost reduction. This may be related to the speed of doing an operation or to saving of labor or supply costs. These can be improvements of an existing method or the result of new processes or inventions, such as new machinery.

Jan 1, 1974

By John S. Cummings

In this paper the phrase "exploration for blind metal deposits" refers to exploration activities geared to the discovery of metal deposits which cannot be located by visual surface inspection. The word "system" refers to all of the components (people, money, corporations, techniques, etc.) which collectively result in an exploration process. The details of the system or systems which I have employed in exploration will not be discussed because of client relationships. However, some of the more severe problems in exploration result from how the system's components interact and our attitudes as to what exploration data is telling us, if anything. It is these items which will be discussed. Exploration for blind metal deposits, which has been relatively intense over the last 2S years compared to rather minor outlays prior to World War II has often been an uncoordinated assortment of various specialists employing various techniques (see Dickerson -1). In a program geared to the location of blind deposits, the lack of outcropping deposits or occurrences should not be a deterrent to a well conceived and well planned program. The severe cyclical swings in exploration activity, although often coinciding with depressed metal prices, by and large result from the failure of exploration operators to present a coherent and realistic program to management. It is my opinion that the stream of complaints criticizing management for cyclical exploration support are mostly unwarranted, as many of the programs and goals are ill defined. Although depressed market conditions may serve as the catalyst for exploration cuts, the underlying cause is that when the "chips are down", the non-directional, non-specific nature of many programs is revealed. Thus management should not be castigated for eliminating such programs during bad times, but rather they should be castigated for supporting them during boom periods.

Jan 1, 1978

By Anthony W. Wakefield

The paper is intended merely as an introduction to methane hydrates, what they are and why they are important. It does not claim to be a cutting-edge research report, but may be useful for those to whom the subject is unfamiliar.

Jan 1, 2008

By I. F. Walder

Mill tailings from skarn-type base metal deposits were studied in order to ascertain potential element mobility in response to weathering. Hypogene ore minerals are sphalerite, galena, and chalcopyrite, showing minor supergene oxidation to smithsonite, cerussite, and covellite. Gangue minerals are pyrite, pyrrhotite, magnetite, hematite, andradite and grossular gamet, hedenbergite, calcite, ankerite, and quartz. Foremost of the eleven tailing piles studied, the hypogene sulfide minerals show no or only incipient post-mining oxidation. Iron oxides and hydroxides form the main oxidation products in the tailings and are enriched in heavy metals. A distinction between pre-and post-mining oxide phases may be obtained based on petrographic observations which distinguish whole-grain versus partial grain replacement. Zn and Cd do not appear to be enriched in the weathering derived oxidation minerals and will be more easily leached from the tailings than other metals.

Jan 1, 1994

By J. Richard Lucas

Today, the future of the coal industry is extremely bright because coal can be produced at a cost which makes it competitive with other energy sources. However, the industry has been forewarned that further cost reductions must be made if it expects to remain a serious contender in the growing energy market. Surface as well as underground operations must be improved. The very same elements which affected production a. few years ago still exist today and will continue to be present in the future. Improvement's in production mining equipment, mining methods, and auxiliary equipment have resulted in reduced costs over the past few years. Efforts must be continued toward further reducing costs in areas which have been improved previously, and new areas should be investigated for possible improvements. Therefore, new techniques must be developed which will enable the industry to augment its current efforts in reducing the cost of mining. The logical place to begin evaluating the factors affecting production and cost is in the immediate face area where a substantial part of the total cost of mining is incurred. The coal industry stands to gain much through the development of new techniques for analyzing the numerous variables affecting production and by establishing methods for eliminating or minimizing the adverse effect of those variables which can be controlled. Intuition and trial-and-error methods have been the standard means used to resolve many of the factors which influence production. As a result, many elements are overlooked or ignored because their effect on production is not pronounced and cannot be readily resolved. The need for a method of analyzing such factors was recognized by the Office of Coal Research. Therefore, in April 1962, under OCR sponsorship, a. research project was initiated at Virginia Polytechnic Institute (VPI). The objective of the project was to identify the factors which influence mining costs in the immediate production area, and to develop methods and techniques which will enable the coal operator to minimize production costs. The objective of the research at VPI has been successful, and techniques have been developed for establishing quantitative facts concerning the interrelationships of production activities.

Jan 1, 1965

By W. J. Miles

Oil based drilling fluids utilize a number of industrial mineral products to accomplish oil and gas drilling in several environments where water based drilling fluids are less effective or inappropriate. These industrial minerals include: organically modified bentonite, organically modified lignite, barite, hematite, mica, calcium chloride and other salts. A variety of organic products are also utilized in oil based drilling fluid formulations. Oil based drilling fluids are preferred in several drilling situations because: they can be used to drill through water sensitive formations; they produce holes that are very close to the drill bit gauge; they exhibit high temperature stability; they are more environmentally acceptable; they minimize producing formation damage; they provide faster drilling rates when used with new polycrystalline diamond drill bits; they minimize pipe sticking and lost rig time.

Jan 1, 1986

By A. K. Bakshi

In cold regions, rinsing of spent cyanide from leach heaps is stopped during winter and is resumed again after the snow melts. The effect of this idle time on the overall removal process was studied in this experiment. Samples were collected for rinsing tests from one heap at a gold mine near Fairbanks, Alaska. Continuous and interrupted rinsing of this sample were carried out in test columns. The rinse solution was analyzed at regular intervals to determine the rate of cyanide removal from the solids. It was found that total cyanide concentration per rinse cycle for interrupted rinsing test was higher than for the corresponding continuous rinsing test. As a result, interrupted rinsing required less rinsing cycles than continuous rinsing.

Jan 1, 1995

By M. Morrongiello

The Kalgoorlie Consolidated Gold Mines Fimiston Open Pit is mining through a dense network of disused level workings and stopes of varied sizes and orientations. This study investigated the interaction between underground workings and the pit slope stability, in particular for the ultimate pit depth of over 600 metres. Parametric analyses were conducted on the structural and rock mass properties in order to provide realistic input. Several cases in both 2D and pseudo 3D using UDEC were modeled and analyzed to investigate the performance of the rock mass at various mining stages. The concept of equivalent property factor was also introduced to model the 3D behavior using 2D models. Based on the modelling results, the possible failure mechanisms and deformation of the pit walls were assessed. Factors of safety have been derived for the pit slope at different mining stages using the strength reduction technique. The modelling results agree well with pit performance monitoring results to date. The concept and results presented in this paper could be a useful reference for operations with similar circumstances and stress regimes.

Jan 1, 2005

By G. Blackwell

In the 1980's the Canadian surface mining industry was confronted by declining competitiveness in the face of low cost foreign producers and alternative materials. Low metal prices undermined profits for many mining companies. Restructuring, rationalization, capacity reduction, technology transfer, as well as favourable currency rates and higher commodity prices, helped revitalize the industry by the close of the decade. Now in the 1990's, however, the need to improve competitiveness for profitability has re-emerged in greater intensity. In the current climate it is considered that there are three strategies available to industry to ensure profitability: continued rationalization and restructuring; optimization of operating practice; and technology development and transfer.

Jan 1, 1993

By Y. C. Kim

The results from a retrospective study are described in this gaper in which she past development drilling activities were investigated using geostatistics. The purpose of the study was to determine the amount of savings in drilling cost that could have been realized through the optimal placement of sequential drill holes using geostatistics. Out of 144 DDH's that were in place within the study area, the results showed a possible elimination of 34 DDH's without any reduction on the confidence interval of the global reserve estimates. If the incremental savings from one drilling campaign to the next were considered, however, the amount of percentage savings were even greater. Other interesting results from this study were; 1) tangible demonstration of the importance of a proper geologic delineation within the study zone, and 2) the robustness of the obtained experimental variograms from the rather early stage in development drilling.

Jan 1, 1981

By W. A. McKinney

In conventional dump leaching of porphyry mine strip wastes, many years are required to extract up to 20 percent of the copper from the contained sulfide minerals. Furthermore, none of the molybdenum, gold, or silver in the strip wastes is recovered by current leaching practices. Because mineralization occurs predominately along fracture planes, breaking of the rock during mining operations liberates and concentrates some of the metal values in the fines. Research shows that upgraded fines can be screened from mine wastes and froth floated for early recovery of copper, molybdenum, gold, and silver. For example, screening a dump sample assaying 0.35 percent copper as chalcopyrite removed about 20 percent of the copper as minus 1/4-inch material that analyzed 0.6 percent copper. About 35 percent of the molybdenum and 20 percent of the gold and silver also reported in the fines. Crushing the mine dump sample to minus 3 inch before screening increased the distribution of copper and molybdenum in the minus 1/4-inch screen fraction to 28 and 50 percent, respectively. Similar results were obtained by screening fines from two other large samples of mine waste dump materials. Flotation studies established that the enriched minus 1/4-inch fines from the three dump samples could be effectively concentrated. Comparative testing revealed that the combination of froth flotation of fines and acid-ferric sulfate leaching of the coarser fraction enabled doubling the recovery of copper over direct leaching of the samples. In addition, significant amounts of molybdenum, gold, arid silver were recovered by flotation.

Jan 1, 1970

By D. Hulse

"The science of “optimal economic pit design” has been highly refined in the last decades. Even with the proliferation of optimizing and heuristic algorithms exploiting ever faster computers, the most common input is a single block model and a single set of cost assumptions, each of which is an estimate and prone to errors. An analysis of price assumptions produces a suite of nested economic shells, each with its own quantities of ore, waste, grade, and profit, but due to irregularities in the mineralized body, the growth of these shells can be erratic. To control the impact of the errors of the model and cost assumptions when choosing the pit shell for design, graphs of pit shells characteristics, such as stripping ratio, cost per unit of product and profit/ton, can be analyzed to consider points with higher stability, or robust pits. Selection of robust shells for a pit limit and for push backs can help to understand the impact to profit and risk. The robust shells also guide the preferred solution sets for final pit and cutoff optimization. INTRODUCTION “An open pit mining operation can be viewed as a process by which the open surface of a mine is continuously deformed. The planning of a mining program involves the design of the final shape of this open surface.” Optimum Design of Open-Pit Mines, Lerchs, H. and Grossmann, I. Transactions C.I.M. Volume LXVIII 1965. Traditionally an analysis of economic pit shells and sensitivity was performed by varying the input metal price. This was done with both floating cone algorithms as well as early versions of the Lerchs-Grossmann (L-G) algorithm. This gave an indication of the pit sensitivity to price but since other variables also change, some with metal price (perhaps steel and equipment), and some independently (fuel and tires) the understanding of these different pits was restricted. In addition, a run of the program could take hours, making a detailed analysis of small changes unwieldy. The L-G algorithm was programmed by a variety of people and sold as part of commercial mining packages, however it was first and most successfully commercialized by Jeff Whittle in 1984. When Whittle’s 3-D™ was expanded to 4-D the parameterization of the economic inputs was considered and the ability to run a suite of “pit shells” became automatic. The competing NPV Scheduler™ program sold by DataMine™ offers similar pit shell analysis capabilities."

Jan 1, 2018

By K. J. Stanaway

Concentrations of minerals between 3.5 and 5 specific gravity such as ilmenite, rutile and zircon in large accumulations of sand constitute "heavy mineral" placers. Two fundamentally different modes of formation characterize "trap" and "bed" placer variants. Smaller and generally higher grade trap placers form during sediment erosion or reworking. Because of their smaller size, they rarely yield economic heavy mineral deposits. They become economic, either if they contain more valuable "heavies" such as gold, or, if they occur within or near much larger but lower grade bed placers. Bed placers form during sediment accumulation episodes in any environment and lithofacies where mineral supply and fluid dynamics are favorable. Three heavy mineral deposits are discussed to illustrate bed placer geology and how trap placers occur with and relate to them.

Jan 1, 1991

By E. McCullough, S. Gaillard

"Diesel particulate matter (DPM) remains a health concern in many underground metal/nonmetal mines, and has been regulated by the Mine Safety and Health Administration since 2002. While the NIOSH 5040 standard method for DPM monitoring is required to demonstrate regulatory compliance, the FLIR Airtec DPM Monitor can serve as complementary engineering tool. It is a handheld instrument that offers near real-time measurements. As part of an ongoing field study, the Airtec has been used to survey elemental carbon concentrations (a proxy for DPM) in an underground stone mine. Via “spot-checking” and more prolonged area monitoring, this effort was aimed at determining spatial and temporal DPM variation in several key locations. INTRODUCTION Diesel particulate matter (DPM) is the solid fraction of the exhaust emissions from a diesel engine. It is largely made up of elemental and organic carbon (EC and OC, respectively), which can be measured as proxies for estimating mass concentrations of DPM. The National Institute for Occupational Safety and Health (NIOSH) considers DPM to be a health hazard and potential carcinogen [1]. It is believed to cause and/or exacerbate respiratory illness upon inhalation, deposition, and retention in lung tissue [2]. Since DPM exists in both the micro- and nano-particulate ranges, it can surpass typical auto-immuno defense mechanisms that keep larger particles out of the respiratory system [2]. Relative to other occupations, the DPM exposure potential for underground miners is high because these individuals work in enclosed environments where diesel powered equipment is frequently used [3,4]. A variety of engineering and administrative controls have been devised to reduce DPM exposures in underground mines, and increased airflow is often a key component of control strategies. In large-opening mines, which are most common in the metal/nonmetal sector, DPM abatement via increased ventilation can be especially complex due to moving and controlling the large air quantities [5]. The Mine Safety and Health Administration (MSHA) has regulated DPM exposure in metal/nonmetal mines since 2002. The final rule limits personal exposure to total carbon (TC, which is the sum of EC and OC) to an eight-hour time weighted average (TWA) of 160 µg/m3. To demonstrate compliance, operators must use the NIOSH 5040 Method [6]. However, the Airtec DPM Monitor (FLIR Systems, Inc., Nashua, NH) was developed as an engineering tool to provide near real-time measurements of both EC and TC for tracking personal exposures [7]. The portable Airtec works by capturing DPM on a filter and successively measuring laser extinction on the filter as DPM accumulates; the EC fraction of the DPM is dark, and so as it accumulates the filter becomes darker and absorbs more laser light [8]. The laser extinction value is directly correlated to EC, but since EC and TC are generally observed in consistent proportions (i.e., TC = EC*1.3), the Airtec is also programmed to display TC as a TWA [9]. There have been multiple studies conducted to validate the Airtec and the instrument has been adopted by some mine operators as a tool for their health and safety programs [3,8]."

Jan 1, 2016

By K. J. Sollman

As a class, silicate minerals have likely found the broadest, if not largest volume, use in combination with polymeric binders of all industrial minerals. Among the silicates, calcium metasilicate, wollastonite, enjoys a front runner position in a near universal sense. It is a viable and desirable part of composites ranging from thin films to large moldings; from a common filler/extender for paint for your garage to a reinforcement for the exterior surfaces of a luxury vehicle affordable to very few. This article is focused upon the variations in particle morphology and the surface characteristics which, by way of commercial examples and discussion of active research programs, make this environmentally benign mineral so unique.

Jan 1, 1993

By Ronald O. Harma

Iron ore pellets made from concentrates produced from low grade iron ores are the primary iron bearing feedstock for iron making in North American blast furnaces. Steelmakers are demanding increasingly higher quality to provide for improved blast furnace productivity, efficiency, product quality and environmental compliance. Unfortunately, this higher quality iron ore product must be produced from the vast deposits of low grade iron ores that are becoming increasingly poorer in quality with regard to mineral liberation and ease of concentration. Since some of these low grade iron ores require grinding to as fine as 90% -500 mesh (25 microns) for liberation and since more of the silicious gangue and other minor undesirable constituents must be removed to provide the higher quality, we have come to depend on flotation to do the added work. Flotation technology and other preflotation unit operations must improve to meet these increasing demands. In many cases, flotation equipment, reagents and circuit operating performance have improved little during the last two to three decades. Mechanical flotation cells have grown from 14 cubic meters (500 cubic feet) to over 84 cubic meters (3000 cubic feet) to help reduce capital and operating costs; however, flotation metallurgical performance has not improved, Column flotation has only recently shown promise in improving metallurgical performance for iron ore rougher flotation. Previous column flotation success was mainly in scavenger and cleaner flotation steps for treating minerals other than iron ore. Although some new flotation chemicals have been developed for removal of silica and other minor constituents under widely varying mineralogical scenarios, recovery of iron mineral has not improved. The operation and control of flotation circuits have become more challenging because of the increasing workload on flotation. Better sensing, process control and operation of flotation circuits are essential as we go forward. Iron ore upgrading by flotation can be classified into either anionic or cationic methods. Anionic flotation of either iron oxide or silicious gangue is accomplished by collector type, pH control and selective chemical activation . Similarly, cationic flotation of silica or iron oxides is accomplished by collector type, activation and/or pH control. Removal of other minor constituents is achieved by using specialty chemicals under controlled conditions for preflotation, co-flotation or post flotation steps. Generally, anionic flotation is used for floating cleanly liberating crystalline oxidized iron ores such as hematite, specularite and martite. Earthy and hydrated oxides such as hematite and geothite can be upgraded with either anionic or cationic collectors after controlled dispersion of slimes or prior removal of slimes. Anionic flotation of silicious waste can be achieved by calcium activation of silica. For magnetic iron ores small amounts of locked silica particles (middlings) can be removed by cationic silica flotation, which is the only method in commercial use in North America today. Historically the efficiency of these iron ore flotation processes has been restricted by the loss of fine iron particles (minus 500 mesh) to the tailings product. New technology is required to overcome this loss and improve overall flotation performance. Development of technology for more selective separation of silica and other minor undesirable constituents from iron ore will provide both quality and cost benefits to the iron and steel producers. Development of future iron ore production in North America will face stiffer technical challenges. These new and undeveloped iron ore deposits are largely oxidized (non-magnetic) and by nature contain more slimes and other undesirable constituents. Unless other new technology evolves, flotation will be the major treatment process required to upgrade these difficult low grade iron ores.

Jan 1, 1993

By Joe D. Mitzel

The Indian Head fine has been in existence since 1922. For over 56 years there have been North Dakota people mining coal at this same location. The area affected will fit inside a circle 5 km in diameter, and the coal is lignite. The seam thickness has varied from 2.4 m to 3.65m, and the overburden from 6 m to 30 m in depth. me Lignite coal which is being mined at the Indian Head Mine is from 15.8 x l0 6 to 16.7 x 10 6 J per kg; it has a moisture content of 33 to 38%; an ash content of 5 to 10%; and a sulfur content of from 0.5 to 0.7%. The moisture content and the fact that we crush the coal co a top size of 14 cm x 0, are two of the characteristics or the product which cause it to freeze and remain inside of the railroad cars on the slope sheets. The market for the coal initially was almost entirely local coal sales. That is, coal was sold to people in the area who used the lignite to heat their homes, stores, offices, schools, and churches. Back in the early 1920's, there were no stoker-fed boilers, or pulverized fuel boilers, as we have in today?s marketplace. Basically, all of the coal was sold as lump coal, pieces about 30 to 35 cm square, to be used in furnaces: and nut coal with a top size of about 7.5 cm to 10 cm to be used in the old kitchen cookstove. All of the coal fines, less than 5 cm, were screened out and layed onto a pile. There was no market for the smaller sizes of the lignite coal. It has been our experience that when the coal is in lumps or chunks larger than 7.5 cm to 10 cm, there is a very slight possibility of freezing. That is the chunks themselves freeze, but by their nature, they do not cling to one another or form large masses of frozen material which are difficult to remove from the slope sheers of the railroad cars.

Jan 1, 1980