Search Documents

By Jessica M. Wempen, Michael K. McCarter

"Differential Interferometric Synthetic Aperture Radar (DlnSAR), a satellite-based remote sensing technique, has potential application for measuring mine subsidence on a regional scale with high spatial and temporal resolutions. However, the characteristics of Synthetic Aperture Radar (SAR) data and the effectiveness of DlnSAR for subsidence monitoring depend on the radar band (wavelength). This study evaluates the effectiveness of DinSAR for monitoring subsidence due to longwall mining in central Utah using L-band (24 cm wavelength) SAR data from the Advanced Land Observing Satellite (ALOS) and X-band (3 cm wavelength) SAR data from the TerraSAR-X mission.In the Wasatch Plateau region of central Utah, which is characterized by steep terrain and variable ground cover conditions, areas affected by longwall mine subsidence are identifiable using both L-band and X-band DlnSAR. Generally, using L-band data, subsidence magnitudes are measurable. Compared to X-band, L-band data are less affected by signal saturation due to large deformation gradients and by temporal decorrelation due to changes in the surface conditions over time. The L-band data tend to be stable over relatively long periods (months). Short wavelength X-band data are strongly affected by signal saturation and temporal decorrelation, but regions of subsidence are typically identifiable over short periods (days). Additionally, though subsidence magnitudes are difficult to precisely measure in the central Utah region using X-band data, they can often be reasonably estimated.INTRODUCTIONDifferential Interferometric Synthetic Aperture Radar (DlnSAR) is a satellite-based remote technique that can be used to measure surface displacement over large regions with high spatial resolution. Under good conditions, displacements can be measured with centimeter to subcentimeter accuracy (Buckley, 2000; Massonnet and Feig!, 1998). DlnSAR also has high temporal resolution, and imaging periods typically range from 10 to 50 days (Rosenqvist, Shimada, and Watanabe, 2004; Roth, 2004). In the last two decades, the application of DlnSAR for mine subsidence monitoring has been demonstrated in coal basins in Europe, Australia, China, and the United States (Camec and Delacourt, 2000; Ge, Chang, and Rizos, 2007; Ge et al., 2008; Ismaya and Donovan, 2012; Ng et al., 2010; Perski, 2000; Perski and Jura, 2003; Popiolek and Krawczyk, 2006; Wegmuller et al., 2005; Wright and Stow, 1999; Zhao et al., 2014; Xinglin et al., 2014). Overall, these studies have demonstrated good data resolution, strong relationships between mine development and subsidence, and reasonable agreement between displacements measured by DinSAR and displacements measured by conventional surveys."

Jan 1, 2016

By Behdeen Oraee, Amirhossein Bangian, Kazem Oraee

"Determination of the optimum design of chain pillars has a significant effect on the economics and safety of longwall operations. Most pillar design formulae are based on empirical methods and supplemented by local experience. They therefore lack versatility of application under different geotechnical conditions.In this paper, in order to illustrate the shortcomings of the above, a typical real coal pillar in Tabas coal mine has first been studied and the conventional formulae have been used to determine the optimum dimensions. The results show that a wide difference exists between the predicted and the real field data. The Oraee-Hosseini formula has then been applied to this mine in order to determine the optimum design. The results from this formula demonstrate a close fit between the theoretical VALUES (and those produced by laboratory tests and in practice. It is further demonstrated that the wide discrepancy between the results obtained from the two formulae is attributed to the dissimilarities between geotechnical conditions of Tabas and the original regions whose data were used to devise the empirical formulae.It is finally concluded that the application of numerical simulation methods and experimental equations together with engineering judgment used by the mining design engineer, will provide the most accurate design characteristics.INTRODUCTIONLongwall is an underground mining method which has a high rate of production capacity and mechanization ability. This mining method, which is appropriately applied for soft rock fiatlying bedded ore bodies, gradually became a widespread mining method amongst European coal mines at the beginning of the 19'h century. It was then applied in some of the U.S. coal mines with the development of self advancing support mechanisms in early 1960's (Oraee, 2001).Underground coal production around the world using Longwall mining method doubled during 1990s. The main reasons for this improvement were: the high level of mechanization, increased 10 safety, adequate design of panels, and well designed ventilation systems (Peng, 2006)."

Jan 1, 2010

By Baogui Yang, Jie Yang, Anthony Iannacchione

"The cemented coal gangue-fly ash backfill technique (CGFB) has commonly been used to control subsidence damage caused by underground coal mining. This paper discusses the CGFB backfilling process used at the Xin-Yang coal mine, Shanxi Province, China. A general description of the components of the CGFB are provided. The reaction of the strata to the backfilling process is simulated with a scaled physical model based on the Xin-Yang conditions and verified with subsidence points on the surface. With the help of the cemented filling materials, the CGFB produces only a slight bend to the overburden roof strata over the longwall panel. Physical models were constructed at the China University of Mining and Technology, Beijing, to simulate actual conditions. The modeling results show minor fracture distribution in the overlying strata and lower abutment pressure development within the backfilling area. The effectiveness of the CGFB technique is verified by a reduction in the vertical surface subsidence measured above the backfilled area.INTRODUCTIONUnderground longwall mining is the most efficient underground means to recover coal resources and is used widely in China, the US, Australia, and Europe. However, this type of mining has introduced some serious environmental impacts. Perhaps the most significant environmental issues are the surface and groundwater impacts associated with the formation of the subsidence basin (Bell and Donnelly, 2006). Backfill technology has been used for years to mitigate subsidence impact. Simply speaking, the backfilling technique places filling materials into the void left from the extraction of coal. When this material is placed within the gob, it is capable of partially supporting the overburden until a new equilibrium is reached. Essentially, the backfill material inhibits crack development and expansion caused by the strata movement and mitigates damaging ground deformations.The cemented gangue-fly ash backfill (CGFB) is one type of novel backfill technology, consisting of cement, coal gangue, fly ash, water, and additives in varying concentrations. The CGFB is mixed on the surface, pumped underground through a pipeline as a slurry, and placed in the void behind the longwall shield under the protection of specially designed hydraulic supports."

Jan 1, 2018

By Stanislaw Prusek

In this paper, results of underground measurements conducted in gateroad 3, seam 615, at the Bobrek-Centrum Colliery are presented. The Bobrek-Centrum Colliery is owned by Kompania Weglowa, the largest hard coal producer in the European Union. Yearly production at the colliery, including the longwall system, is about 2 million tonnes. Gateroad 3 was used simultaneously for two retreating longwall faces, No. 1 and No. 2. This working was also employed for the conveyor belt for longwall No. 1 and served as a transport road for longwall No. 2. Approximately 100 meters of gateroad 3 was maintained behind the face of longwall No.1 and then, with the progress of longwall No. 2, it was liquidated. In this paper, we present the results of underground measurements of vertical and horizontal convergence in gateroad 3. We also present the results of numerical modeling for deformation of the working. Finally, we analyse the accuracy of the numerical calculations by comparing them to the actual deformation of gateroad 3.

Jan 1, 2014

By Jessica M. Wempen

Differential Interferometric Synthetic Aperture Radar (DInSAR), a satellite-based remote sensing technique, has been demonstrated as a potentially practical method for measuring mining induced surface subsidence. Unlike traditional methods of subsidence monitoring, DInSAR has the capacity to generate subsidence data on a regional mining scale with a relatively high data density. Using DInSAR to evaluate subsidence over large regions with relatively long time scales has the potential to help quantify the impact of subsidence in the mining region, and provide a means for validating whole-mine geotechnical models. In this study, nine pairs of interferometric data from the Japanese Advance Land Observing Satellite (ALOS) were processed using DInSAR to generate displacement maps for a group of trona mines in southwest Wyoming. The data cover a time span from December 2007 to March 2011. The maximum subsidence for one of the mines totaled 1.3 meters for this period. Cumulative DInSAR displacement maps show the development of subsidence over time. In this mining region, surface subsidence is generated primarily by extraction of trona using retreating longwalls. Additionally, trona is extracted by solution mining, which also generates measurable surface subsidence.

Jan 1, 2014

By Juan J. Monsalve, Nino Ripepi, Richard Bishop, Jon Baggett

"Terrestrial laser scanning (TLS) is a useful technology for rock mass characterization. A laser scanner produces a massive point cloud of a scanned area, such as an exposed rock surface in an underground tunnel, with millimeter precision. The density of the point cloud depends on several parameters from both the TLS operational conditions and the specifications of the project, such as the resolution and the quality of the laser scan, the section of the tunnel, the distance between scanning stations, and the purpose of the scans. One purpose of the scan can be to characterize the rock mass and statistically analyze the discontinuities that compose it for further discontinuous modeling. In these instances, additional data processing and a detailed analysis should be performed on the point cloud to extract the parameters to define a discrete fracture network (DFN) for each discontinuity set. I-Site Studio is a point cloud processing software that allows users to edit and process laser scans. This software contains a set of geotechnical analysis tools that assist engineers during the structural mapping process, allowing for greater and more representative data regarding the structural information of the rock mass, which may be used for generating DFNs. This paper presents the procedures used during a laser scan for characterizing discontinuities in an underground limestone mine and the results of the scan as applied to the generation of DFNs for further discontinuous modeling.INTRODUCTIONAccording to the Mine Health and Safety Administration (MSHA), between 2006 and 2016, the underground stone mining industry had the highest fatality rate in 4 out of 10 years, compared to any other kind of mining (MSHA, 2016). Additionally, during that same time, 40% of the fatalities were due to ground control issues, such as roof and rib collapses and pillar bursts. The National Institute for Occupational Safety and Health (NIOSH) developed guidelines for designing underground stone mines (Esterhuizen, Dolinar, Ellenberger, and Prosser, 2011). However, these guidelines do not apply to all underground stone mines.Monsalve, Baggett, Bishop, and Ripepi (2018) present a case study of an underground limestone mine experiencing a structurally controlled mode of failure. The authors analyze different methods to study that type of instability. They conclude that the integration of terrestrial laser scanning (TLS) with discrete element modelling (DEM) can be used to prevent rock falls in underground excavations to enhance worker safety. However, an adequate rock mass characterization and structural mapping must be performed in order to generate reliable models that allow the engineer to have a better understanding of the rock mass behavior."

Jan 1, 2018

By Ross W. Seedsman

The in situ behaviour of claystone floors associated with the Wallarah, Great Northern and Fassifem Seams has been studied using a comprehensive suite of stress and displacement monitors. The instrumentation was supplemented by in situ and laboratory testing of the claystone materials. The instrumentation demonstrated that the presence of claystone floors is associated with floor heave, extra rib spall, and settlement of the pillar into the floor. Horizontal floor extensometers showed that the depth of extrusion of clay was limited to 1-2 in. A pore pressure transducer installed in a claystone floor demonstrated the possible existence of short-term undrained behaviour of the claystone. Long term swelling of destressed claystone was also documented. Settlement of pillars into claystone floors can be analysed using simple elastic theory. The assumption of plane strain is valid for most claystone thickness/pillar width aspect ratios. Floor heave can be analysed using bearing capacity concepts. However, it is considered that heave is the result of local bearing capacity failure in the rib spall zone. The advantage of this model is that the bearing capacity equation can be applied without resort to unrealistically high factors of safety.

Jan 1, 1992

By Winton J. Gale

The subsidence over a longwall panel at Tahmoor Mine in the Southern Coalfield of NSW, Australia, was found to be approximately twice the size it had been in previous measurements. An investigation into the potential causes was conducted using computer modeling together with hydrological characterization and detailed geotechnical characterization of the strata. The abnormal subsidence was found to be consistent with localized weathering of joint and bedding planes above a depressed water table adjacent to an incised gorge. The study showed that other factors such as variation in stress field, joint zones, variation in rock strength and topographic factors did have sufficient impact to induce the abnormal subsidence. The results have significant implications to subsidence prediction in areas that may be prone to the phenomenon found at Tahmoor. Key indicators of the potential for this form of abnormal subsidence are presented.

Jan 1, 2011

By Peng Cao, Jimin Su, Yang Li

"Abutment pressure distribution is different when a longwall panel is passing through the abandoned gateroads in a damaged coal seam. According to the geological conditon of panel E13103 in Cuijiazhai Coal Mine in China theoretical analysis and finite element numerical simulation were used to determine the front pressure distribution characteristics when the longwall face is 70 m, 50 m, 30 m, 20 m, 10 m, and 5 m from the abandoned gateroads. The research results show that the influence range of abutment pressure is 40 m to 45 m outby the face, and the peak value of front abutment pressure is related to the distance between the face and abandoned gateroads. When the distance between the longwall face and abandoned gateroads is reduced from 50 m to 10 m, the front abutment pressure peak value kept increasing.When the distance is 10 m, it has reached the maximum. The peak value is located in 5 to 6 m outby the faceline. When the distance between the longwall face and abandoned gateroads is reduced from10 m to 5 m, the front abutment pressure sharply decreases, the intact coal yields and is even in plastic state. The peak value transfers to the other side of the abandoned gateroads. The research results provide a theoretical basis for determining the advance support distance of two gateroads in the panel and the reinforcement for face stability when the longwall face is passing through the abandoned gateroads.INTRODUCTIONFront abutment pressure is the result of rearrangement of in situ rock stress caused by the mining (removal) of the coal seam. Research on the distribution character of face abutment pressure have significant importance in confirming the width of the coal pillar and the distance of advance support in roadways (Liu et al., 2011; Liu, Jiang, and Zhu, 2015). Currently, there is a lot of research on abutment pressure characteristics of traditional longwall coal faces, thick coal seam longwall faces, isolated faces, and extra wide face abutment pressure distribution (Xie et al., 2006). However, theoretical analysis and research on the distribution law of the fully mechanized coal face to abandoned gateroads are relatively less. Abandoned roadways are often from less mechanized or room and pillar mines. Due to the existence of these roadways pre-longwall mining, the in situ stress has already been redistributed around the roadway (Liu et al., 2007). Thus, when the longwall approaches and mines through the roadway, the abutment pressure distribution behaviour has different characteristics than those of traditional solid undisturbed coal. Especially when the face approaches the abandoned roadway, the understanding of face abutment pressure distribution has significant importance to the timing of support installation (Ren and Ning, 2014). This prevents the occurrence of a roof and rib failure ahead of and on the longwall and highly efficient advance of the longwall safely and productivity. This paper analyses the E13103 face of the Cuijiazhai Mine of Wenzhou Mining Co., Ltd of Kailuan Group, as the engineering case study, and uses FLAC3D numerical simulation software to conduct numerical simulated analysis on the abutment pressure distribution mechanism of longwall coal mining face."

Jan 1, 2018

By Stephen C. Tadolini, John P. McDonnell

"High-strength cable bolts have been used for ground support in underground coal mines for many years. Cable bolts are routinely used as secondary ground support in numerous longwall gateroad support applications, areas that possibly experience the most severe conditions in current underground coal mining. Additionally, when mining ground conditions deteriorate, engineers oftentimes recommend cable supports as a principal solution because of the established credibility for successful ground control. Nevertheless, there is still a reluctance to utilize non-tensioned cable supports as an effective primary roof support alternative.This paper provides historical and recently documented examples of non-tensioned cable supports utilized as an effective primary ground support method in a western U.S. underground coal mine, and it will continue the technical discussion between the differences of various degrees of tension in cable supports with respect to ground behavior and reactions.INTRODUCTIONResin-grouted cable supports are widely used to support difficult ground conditions throughout the world. Through the use of innovative applications and configurations they have proven to be a major paradigm shift in roof support and ground control technology in the U.S. (Tadolini and Koch, 1993; McDonnell et al., 1995; Tadolini and Gallagher, 1994; Tadolini and Trackemas, 1994)Today, the basic cable bolt support consists of a high-strength steel cable installed in bore holes that range in diameter from 25 to 50 mm (1 to 2 in) depending on the strand size and drilling equipment. Cables are offered in both bright and galvanized, for corrosion protection, and range in capacity from about 30 to 60 tons. An example of a resin-grouted cable bolt and the key components is shown in Figure 1. The steel cables are flexible and the support length is not limited by the height of the opening. Lengths of up to 10 m (32 ft) have been supported with high pattern densities when standing supports were not operationally feasible. The most common lengths are 3 to 5 m (10 to 16 ft). An important physical characteristic is that PC-strand has an ASTM minimum elongation requirement of 4%. For comparison purposes, the ASTM 432-08 Standard Specifications for Roof and Rock Bolts and Accessories specifies elongation requirements for traditional roof bolts are a minimum of 12% for grade 40, 9% for grade 60, and 8% for grade 75 materials, respectively. Traditional roof bolts can stretch and elongate twice the length that cable bolts can, which makes design considerations challenging."

Jan 1, 2010

By Jesse Puller, Ken W. Mills, Owen Salisbury

"An underground coal mine located in New South Wales has a target coal seam located 160-180 m deep directly below a 16-20 m thick conglomerate unit that has been associated with significant periodic weighting events on the longwall face. As part of the investigations to better understand the causes of periodic weighting at the mine, inclinometers capable of measuring horizontal shear movements through the full section of the overburden strata were installed ahead of mining at two locations approximately 1 km apart above the centre of two longwall panels. These inclinometers were monitored as the longwall approached each site. This paper presents the details of the installation, the results of the inclinometer monitoring at both sites, and the insights that these measurements provide for overburden behaviour about longwall panels.Horizontal shear movements were observed to develop on shear horizons that correlate closely across the two sites suggesting a mechanism that is consistent across a large area of the mine. Shear movements were observed to develop on a single horizon near the top of the conglomerate strata that was mobilised almost immediately after initial formation of the longwall goaf at a distance of 425 m ahead of the longwall face. The direction of horizontal movement was consistent with the relief of the major principal horizontal stress. As the longwall face approached each inclinometer, other horizons within the upper part of the overburden strata begin to shear with the upper strata moving toward the approaching goaf more than the lower strata. Within the last 30 m of longwall approach, tilting of the strata associated with the increase in vertical subsidence toward the extracted goaf caused a change in the style of deformation with tilting and reverse shear offsets.INTRODUCTIONLongwall mining is recognised from subsidence monitoring, surface extensometer measurements, and various other observations to cause significant disturbance to the overburden strata directly above the extracted goaf of each longwall panel. Disturbance to the overburden strata beyond the limits of each longwall panel is not so well understood. Subsidence monitoring indicates that horizontal movements beyond the edges of the extracted longwall panel are generally greater in magnitude than vertical subsidence and horizontal movements may extend up to several kilometres from the edge of the panel in some circumstances (Reid 1998, Reid 2001, Hebblewhite et al 2000, Mills 2001, Mills 2014). The mechanics of how these movements are accommodated within the overburden strata is only poorly understood and there are few direct measurements."

Jan 1, 2015

By Boqiang Wu, Ganggang Xu, Xiaodong Wang, Hai Wang, Shibin Zhu

"Using a paste-like slurry as a filling from the ground surface to the goaf, artificial pillars can be built in the cavity goaf to support the goaf roof to prevent roof collapse and ground subsidence. If the accumulation laws of paste-like slurry are known well, the filling technology can be optimized. The laws can establish the foundation for finding out the best methods for building artificial pillars and filling technology. In order to understand the accumulation laws of paste-like slurry in the cavity goaf, Aeolian sand with wide distribution in northwestern China was selected as aggregate, and Portland cement was used as cementitious material to prepare a paste-like slurry. A test model of the cavity goaf was built to simulate the filling process by pump from the ground surface to the goaf to study accumulation laws of the paste-like slurry. The results show that the whole process of expansion and accumulation of the paste-like slurry could be divided into stages: free expansion, fill tightening expansion, and stable expansion. The angle of repose of the accumulation body of the paste-like slurry is constant in the stage of stable expansion, and it is the final angle of repose of the accumulation body. The angle of repose of the accumulation body is highly relevant to the slump of the paste-like slurry, and it is unrelated to the distance between the floor and roof. Under certain conditions of the cavity goaf, reducing the slump of paste-like slurry is one of the effective ways to obtain cost-effective pillars.INTRODUCTIONA large number of cavity goafs of coal mines were left in northwestern China; they were formed in the mining process by room-pillar or strip mining. Safety coal pillars were used to support the roof to keep long-term stability in the goaf, so the ground subsidence was not obvious (Fu, Deng, and Zhang, 2011; Xie, 2014). With gradual weathering, destruction of coal pillars, or additional load from ground surface buildings and structures, there could be a risk of instantaneous collapse of the roof in the goaf. This would affect the safety of existing structures on the ground and adjacent mines (Qu et al., 2017; Li, Xiang, and Jia, 2011; Tan, Guo, and Zhao, 2016; Tan et al., 2017). For disaster prevention of the falling cavity goaf, the current common practice is full filling (Hu et al., 2008; Liu, Zhu, and Huang, 2015; Pan and Wu, 2010). However, for buildings and structures with lower deformation requirements, full filling is excessive. For example, it is acceptable for goaf treatment under general roads and industrial sites to control the maximum deformation and keep the deformation continuous (Liu, 2011; Liu, 2012)."

Jan 1, 2018

By Morgan M. Sears, Mark Van Dyke, Gamal Rashed, John Rusnak, Khaled Mohamed

"In 2016, room-and-pillar mining provided nearly 40% of underground coal production in the United States. Over the past decade, rib falls have resulted in 12 fatalities, representing 28% of the ground-fall fatalities in U.S. underground coal mines. Nine of these 12 fatalities (75%) have occurred in room-and-pillar mines. The objective of this research is to study the geomechanics of bench room-and-pillar mining and the associated response of high pillar ribs at overburden depths greater than 1,000 ft. This paper provides a definition of the bench technique, the pillar response due to loading, observational data for a case history, a calibrated numerical model of the observed rib response, and application of this calibrated model to a second site. INTRODUCTION Bench mining is a an underground mining technique typically applied to room-and-pillar mines where full seam extraction on development presents an unacceptably high risk of injury from high pillar ribs or where the mining equipment is not designed to extract the full seam thickness. To mitigate the increased risk associated with high ribs and slender pillars, a more modest thickness is extracted from the top of the seam on development. This is followed by grading the floor and recovering the bottom of the seam with or without extraction of the pillars during retreat mining. A mine located in Eastern Kentucky extracts two seams at depths ranging from outcrop to 2,000 ft. In some areas of the mine, Seam A and Seam B are close enough together to be mined simultaneously. Seam A (top) is mined on development 7 to 9 ft. high for the entire length of the panel. On retreat, as each pillar is extracted, the continuous miner is ramped down into the floor (Seam B), two pairs of Mobile Roof Support (MRS) units are set, and the pillars are extracted at the full mining height of 14+ ft. During the pillar recovery process, the floor is extracted in each entry, from a ramp initiated outby the retreat line, sequentially just prior to extracting the lifts from the pillars (see Figure 1)."

Jan 1, 2017

By Gautam Benerjee, Veera Reddy Boothukuri, Bhattacharjee Ram Madhav, Panigrahi Durga Charan

"India’s tryst with mechanized longwall coal mining started with the introduction of the first self-advancing powered support longwall (PSLW) face at Moonidih Colliery of Jharia Coalfield in 1978 and at Godavarikhani (GDK)7 Incline of Singareni Collieries Company Limited (SCCL) in 1983. During the last 37 years, about 30 longwall units in Coal India, Ltd., (CIL) and 10 longwall units in SCCL have been introduced with powered roof supports of varying capacity, ranging from 280 to 800 tonnes, in many mines in India under varying geological and geotechnical conditions. The majority of the longwall faces in India have been worked under relatively shallow cover (up to 200m), and significant strata control problems have been encountered due to poor caveability of the roof, inadequate capacity of the supports, a lack of knowledge on longwall caving mechanisms, less than adequate strata monitoring systems, and the non-availability of quality spare parts, etc. This has resulted in structural damage to supports and increased downtime of the equipment, thereby making longwall mining in India a case of technology failure. Energy demand for a developing country like India with a population of 1.2 billion is huge, and the thrust on increasing coal production continues. However, the share of coal production from underground mines in India continues to decline (current share is around 6%) because of absence of successful mass production technology in underground coal mining. Under this backdrop, a high-capacity longwall with state-of-the-art technology was introduced in 2014 at Adriyala Longwall Project (ALP) of SCCL for the first time in Indian Coal Mining Industry. The first longwall panel (LWP) has been completed successfully. This paper highlights the major geotechnical challenges encountered during development of the longwall gate roads due to the presence of two overlying clay bands, significant in-situ horizontal stresses and the experience of using rigid (welded) steel wire mesh with resin-anchored roof bolts. Efforts have been made to analyze longwall weighting and caving behavior, such as main and periodic weightings, the effect of front and side abutment pressures, and the behavior of gate roadway support systems under immediate friable weak roof with overlying massive sandstone."

Jan 1, 2017

By Sean C. Farrell

In underground mining and tunneling, machine design is predominantly dictated by mine conditions and individual customer desires. In partnership with Australian companies WDS Limited and Cram Fluid Power, the engineering department of J.H. Fletcher & Company was tasked to design and manufacture roof bolting modules to be mounted off both sides of a roadheader, providing in-cycle bolting. The objective was to produce a boom and bolt module that would allow an operator to bolt from a remote location, eliminating the need for miner to work in unsupported ground. The bolt module needed to operate in front of the cutting boom, but retract to a parked position out of the way during the cutting cycle. Due to Australian electrical approval requirements, it was desirable to design the module with minimal use of electrical controls. The need for multiple, complex, drill steel and bolt handling steps led to the need for a custom hydraulics package to automate several of the movements. The result of the design is dual drill and bolt modules mounted to a multistage boom with over 24 feet (7.31 m) of extension. Each unit rotates and tilts to meet the bolt pattern requirements in conjunction with the stow and load requirements. The bolt module builds on previous designs incorporating a modular assembly with each sub-component designed to be replaceable and adjustable independently from other machine components. Each major component is painted a different color to help the operator make the connection visually from the module to the operator?s control valves. Hydraulic package valves were designed to automatically control several of the sub-components during the drill cycle, reducing the number of steps a drill operator would, otherwise, have to do manually. This design removes the operator from working in unsupported roof and away from other inherent hazards, putting them at a safe distance on the operator?s platform. The cutting and bolting equipment has been combined into one machine, which is advantageous in single entry drifts because there is no need to place change equipment. The hydraulic package valves eliminate the need for any electronics, thus avoiding any electrical regulations with respect to the controls. The addition of these modules to the roadheading machine increases miner safety and streamlines production while meeting the ground control support requirements.

Jan 1, 2014

By Lou Gaozhong, Guo Wenbing, Zhao Gaobo, Wang Shuren

"The height of a fractured zone due to high-intensity mining (HIM) plays a vital role in the safety analysis of coal mining under bodies of water. This paper described the characteristics of HIM. The processes of overburden failure transfer (OFT) are analyzed. The state of destruction transfers from a certain stratum to the upper stratum as face advance distance increases, and the processes of OFT are divided into two stages: transmission development stage and transmission termination stage. Through theoretical analysis, the limited suspension-distance and limited overhanging distance of each stratum are proposed to judge the damage of each layer. Based on this, the OFT criteria of fractured zone development are obtained. The mechanical model of strata suspended integrity and overhanging stability are established. Finally, a new method to predict the height of fractured zone due to HIM is put forward based on the processes of OFT, the limited suspension-distance, and the limited overhanging distance. Further, a HIM panel in the Datong coal mine is taken as an example. Theoretical methods are proposed, and engineering analogy is used to predict the height of the fractured zone, which is compared with in-situ measurements reported in the literature. The results show that the in-situ measurements for the height of the fractured zone are in close agreement with the theoretical calculation result. Therefore, the rationality and reliability of the theoretical method proposed to predict the height of fractured zone is verified.INTRODUCTIONThe height of the fractured zone (HFZ) due to the exploitation of coal is a key parameter for the safety analysis of coal mining under a body of water (Wenbing, Youfeng, and Hou, 2012). Accordingly, it is necessary to predict HFZ under the corresponding mining conditions before coal mining."

Jan 1, 2018

By Karsten Zimmermann, Peter Cain

"To receive regulatory approval for a new coal mining operation in North America, extensive investigations of feasibility and potential environmental impacts, including ground deformations, are required. Figure 1 shows pictures from mine sites and an example mine map with the planned panel layout for one seam of the multi-seam longwall operation considered.The cumulative mined coal thickness of 22 meters in some areas of the operation requires a comprehensive forecast of expected ground movements and subsidence impacts (e.g., subsidence, slope, displacement, curvature and strain). In the frame of the impact study, the prediction of these impact factors was conducted by DMT using the computer program SPS 4D, based on the Ruhrkohle modeling method by Ehrhardt and Sauer (1961).This paper briefly presents the modeling method and explains the benefits and possibilities for its international application. Information gathered from literature studies on subsidence in North America were incorporated into the initial model parameterization. The article shows the ways in which the observed influences of mountainous topography on surface displacements and deformations can be considered by an extension of the subsidence prediction model and integration of DEM information.SUBSIDENCE MODELFor the calculation of mining-induced subsidence and deformation, DMT has developed subsidence prediction software SPS 4D, which is built according to the stochastic prediction model by (Ehrhardt and Sauer, 1961). The model is based on the subsidence theory by (Knothe, 1953) with a specific parametrization of the stochastic influence function and includes enhancements for dynamic subsidence calculations after (Sroka, 1978). In Europe, mainly in Germany and Poland, the model is approved by the authorities as a standard model for subsidence prediction in mining areas. However, extensive research within R&D activities has shown the possibility to predict mining-induced subsidence considering the specific mining conditions in North America (Zimmermann and Fritschen, 2007)."

Jan 1, 2016

By Enguang Zhu, Kangning Zhang, Yang Li

"Due to the use of outdated mining technology or room and pillar mining process in small coal mines, the coal recovery ratio is only 10% - 25%. In many regions of China: the damage area caused by the small coal mines amounted to nearly one hundred square kilometers. Therefore, special mining techniques must be taken to reclaim the wasted resource in disturbed coal areas. This paper focuses on the different mining methods by analyzing the longwall panel layout and abandoned gateroad (AG) distribution in in the abandoned area of Cui Jiazhai Coal Mine in northwestern China. On the basis of three-dimensional geological model, FLAC- 3D numerical simulation was employed. The abutment pressure distribution was simulated when the panel face passed through the disturbed areas. The proper angle of the inclined face was analyzed when the panel face passed through the abandoned gateroads. The results show that the head end of the face should be 13-20m ahead of the tail end. The pillars on both sides of abandoned gateroads had not been damaged at the same time, and no large-area stress concentration occurred above the main roof. Therefore, the coal reserves of disturbed areas can be successfully recovered by using underground longwall mining. INTRODUCTIONDuring the 70-90's, there were a lot of small coal mines in China. Due to their disordered mining, most of the small coal mines left a great many abandoned gateroads (defined as AG in this paper) and a large area of damage coal seam. In these type of coalfields, there exist many mining risk issues, including nonuniform stress in the overburden, flooding and hazardous gases accumulated in the gob. So how to lay out a longwall panel and successfully mining under this type of abandoned small mines is a big issue nowadays in China.As mentioned above, longwall panel is being performed in the damaged coal seams in order to increase recovery of coal reserves (Wang, 2009). However, the abandoned geteroads intersect to each other all around the area. So a series of production issues arose while the panel face is passing through these AG. Gang and Gong (2015) analyzed the roof stability and abutment pressure distribution during the face was passing those AG that were parallel and inclined to the faceline. Xie, et al. (2015) proposed the ground control mechanism by passing the AG in top-coal caving longwall mining. He recommended to stop the face advance until the roof is over, using high strength bolts and cable bolts, and grouting consolidation. This paper studies the different mining methods by analyzing the longwall panel layout and AG distribution in damage coal seams. Theoretical analysis and field observation were conducted to determine the overburden movement when the face was advancing under the AG. The pillar between face and parallel AG changes from elastic to plastic and eventually to the residual supporting status. All these three status was combined with the roof structure to establish the theoretical model to calculate the shield support capacity. Numerical modeling was employed to simulate the pillar stability and determine the abutment pressure distribution as the face inclined to the AG during longwall mining."

Jan 1, 2016

By Douglas Tesarik, Mark K. Larson, Habte Abraham, Heather E. Lawson

Dynamic failures, or "bumps", remain an imperative safety concern in underground coal mining, despite significant advancements in engineering controls. While many factors have been empirically linked to the occurrence of dynamic failure events, identifying a consistent, repeatable set of criteria within a field setting has proven elusive; conditions generally associated with dynamic failure might produce an event at one site, but not another. Conversely and more troubling, dynamic failure could occur where relatively few of these factors exist. The presence of spatially discrete, stiff roof units, such as paleo channels, are one such feature that has been linked to the occurrence of dynamic failure events. However, an empirical stratigraphic review investigating the relative frequency of discrete units in bumping versus non-bumping deposits indicates that no significant difference exists based on this criterion alone, and that instead an apparent relationship exists between reportable bump history and the overall character of the host rock with respect to stiffness. Due to the complexity of the bump problem, however, these results are not conclusive, as they do not take into account any variable other than the presence or absence of stiff members in the roof lithology; To weight the relative impact of changes in a single variable, such as the thickness or location of sandstone members, it must be examined in isolation-i.e. in a setting where all other variables are held constant. Numerical modelling provides this setting, and the effects of variability in a stiff discrete member in a hypothetical longwall mining scenario are investigated within the context of three stratigraphic "types'', as determined by the ratio of stiff to compliant stratigraphic members; Compliant, Intermediate and Stiff A modelling experiment examines changes in rupture potential in stiff roof units for each stratigraphic type as discrete unit thickness and location are manipulated through a range of values. Results suggest that the stiff-to-compliant ratio of the host rock has an impact on the relative stress-inducing effects of discrete stiff members. In other words, it is necessary to consider both the thickness and the distance to the seam, within the context of the host rock, to accurately anticipate areas of elevated rupture induced hazard; acknowledging the presence of a discrete unit within the overburden in general terms is an insufficient indicator of risk. Through modelling of anticipated changes in the placement and dimensions of discrete units within their stratigraphic setting, elevated rupture-induced bump hazard can be anticipated on a case by case basis. Were similar modelling studies conducted at mine sites in tandem with tracking of problematic discrete stiff units, areas of elevated rupture risk could be anticipated in advance of mining. Developing this predictive capability beyond identifying rupture potential in discrete roof members is essential to the eventual elimination of dynamic failure related worker injuries and fatalities. As stress is a necessary component in the occurrence of dynamic failure events, this finding helps to refine our understanding of the role of individual stiff, strong roof members in bumping phenomena, and suggests that a more holistic view of overburden lithology, combined with site-specific numerical modelling, may be necessary to achieve greater miner safety.

Jan 1, 2016

By Yongping Wu

Roadway deformation and stress migration occur with uncertainty and randomness because of geology, tunneling and mining influence. In order to study the surrounding rock deformation and failure mechanisms in three-dimensional stress state, an air return roadway of Yuanyang Lake mine of Shenhua Ningxia Coal Industry Group Co., Ltd. was chosen as a research object. The three-dimensional model was a designed and completed experiment with a dynamic-static coupling load. The model was loaded by hydraulic cylinder, simulating the in-situ rock stress field and the induced stress field of surrounding rock. The deformation monitoring system of the roadway model was constituted by optical total stations, borehole observation instruments, acoustic emission monitoring, and stress sensors. A wealth of data was obtained through an omni observation of surface displacement, characteristics of stress distribution, and deformation and failure of surrounding model material. By acoustic-optic-electric methods, a real-time testing on physical, mechanical, and damage parameters was realized through the experimental process. The results showed that the data of deformation and failure obtained from the deformation monitoring system of the roadway were authentic, which has great significance for warning and forecasting safety hazards of surrounding rock in coal mines.

Jan 1, 2013