Search Documents

By Adriana Gómez

White dross is a result of the aluminum oxidation during its primary production and is mainly composed of metallic aluminum, Al2O3, with minor amounts of AlN and some other oxides. Because of the great variety of phases, the quantitative characterization is complicated. This work shows a quantitative method to determine the main phases of white aluminum drosses by means of X-ray diffraction (the Rietveld method). Nowadays the Rietveld method is maybe the most useful method for obtaining quantitative phases information in multicomponent mixtures, this method permits relatively quick quantitative phase analysis by fitting the calculated X-ray diffraction profile with the observed one. The analysis were done using powder with a grain size less than 45 µm; to obtain the suitable material size the aluminum dross was grounded by ten minutes, several times. The grounded material was screened, and the material smaller than 45 µm was taken to quantitative XRD analysis. Keywords: Rietveld Method, Characterization, Aluminum dross.

Jan 1, 2005

By Anja Pfennig, Axel Kranzmann, Sabrina Schulze

The CCS technique involves the compression of emission gasses in deep geological layers. To guarantee the safety of the site, C02-corrosion of the injection pipe steels has to be given special attention when engineering CCS-sites. To get to know the corrosion behaviour samples of the heat treated steel 1.7225 42CrMo4, used for casing, and the stainless injectionpipe steel 1.4034 X46Cr13 were kept at T=60 °C and ambient pressure as well as p=lOO bar for 700 h - 8000 h in a C02-saturated synthetic aquifer environment similar to possible geological on-shore CCS-sites in the northern German Basin. The isothermal corrosion behaviour obtained by mass gain of the steels in the gas phase, the liquid phase and the intermediate phase gives surface corrosion rates around 0.1 to 0.8 mm/year at ambient pressure and much lower about 0.02 to 0.2 mm/year at 100 bar where the C02 is in its supercritical state. Severe pit corrosion with pit heights around 4.5 mm are only located on the 42CrMo4 steel. Main phase of the continuous complicated multi-layered carbonate/oxide structure is siderite F eC03 in both types of steel.

Jan 1, 2013

By Wei Yin, Bin Xu, Qian Li, Yongbin Yang, Tao Jiang

Copper anode slime is an increasingly significant resource for precious metals such as Au, Ag and Pd. The extraction of Au, Ag and Pd from decopperized anode slime by different pretreatments and different lixiviants including cyanide, chloride, thiourea and thiosulfate have been investigated. When oxidizing roasting pretreatment was carried out under the conditions of roasting time 120min and temperature 625 ℃, the removal ratios of S and Sb could reach 82.18% and 98.52%, respectively. And the following alkaline leaching of calcine could result in the dissolution of 46.40% Cu and 98.48% Pb. The optima leaching ratios of Au, Ag and Pd reached 99.48%, 97.69%, 94.79% by cyanide leaching, and 95.01%, 79.84%, 96.59% by chloride leaching, and about 95.21%, 95.66%, 48.79% by thiourea/thiosulfate leaching.

Jan 1, 2015

By Kang Wan, Lei Tang, Jianchao Li, Jieyu Zhang, Minqi Sheng, Jifang Xu

"The viscous flow phenomenon in slag close to the liquidus temperature was considered. A simple approach that liquidus temperatures of melt could be derived from viscosity data was employed. The potential of this method for estimating the liquidus temperatures of pure water and binary alloy was demonstrated. The liquidus temperatures of the CaO-Alz03 based slags obtained from the second derivative method depends upon the number of viscosity values available at different temperature intervals. The results indicated that plots start deviating from the straight-line behavior at temperature as expect, and the second derivatives show the break points at a certain temperature, which is the liquidus temperature. Comparisons among the present observations as well as the characteristic temperature of the selected slags, which measured by the hemisphere method and DSC, indicated that it is possible to get a reasonable idea of estimate the liquidus temperatures from activation energies for viscous flow.IntroductionThe liquidus temperature of slag, which has a significant effect on the kinetics of chemical reactions and the slag-metal separation, is extremely important for metallurgical operations. Experimental measurements of the liquidus temperatures of slags are difficult, since slags invariable supercool. In addition, behavior of a single constituent in a multi-component slag is different in different circumstances due to its interaction with other constituents. Hence, it is essential to study the liquidus temperature of each particular slag resulting from a special process. Usually, the compositions of the slags aimed to the single liquid region of the phase diagram. However, the phase diagram of many slag systems, which back often to the 1950's, involves considerable uncertainties. Many liquidus temperatures are given as dotted lines in Slag Atlas [1]. Disagreements between the phase diagram and the reality have been found [2]."

Jan 1, 2013

By Vinicius Alves Gomes, Jean Igor Margem, Frederico Muylaert Margem, Sergio Neves Monteiro, Marina Rangel Margem

The interface between the matrix and the reinforcing fiber plays an important role in the efficiency by which an applied load is transmitted through the composite structure. The shear stress at the fiber/matrix interface can be associated with this load transference and, consequently, affects the composite strength. In the present work, pullout tests were used to evaluate the interfacial shear stress of malva fiber in epoxy matrix composites. A small critical length was found for the malva fiber embedded in epoxy, which corresponds to a relatively weak fiber/matrix bond and lower interfacial strength.

Jan 1, 2015

By Xiao-hui Fan, Xu-ling Chen, Xiao-xian Huang, Gui-ming Yang

Grate-kiln-cooler is a predominant process of producing iron ore pellets in China. Since this process is of multi-variant, strong coupling and large hysteresis characteristics, a reliable performance monitoring is thus essential to ensure product quality and economic benefits. Aiming to efficiently monitor the pellet induration within this process, this study proposed an approach that combines statistical analysis and quality soft-measurement. Soft-measurement of pellet quality was accomplished based on the predicted time-temperature profile, and the soft-measured indices were on-line monitored using statistical control charts. Based on the proposed approach, a monitoring system for grate-kiln-cooler thermal process was developed for a domestic pelletizing plant. Running results demonstrate that our system can assist in the detection or diagnosis of abnormal thermal state and finally helps to stabilize the pellet production.

Jan 1, 2016

By M. Okido, R. Ichino, K. Kuroda

"Compound semiconductor, ZnTe, was electrodeposited in an acidic solution with K2TeO3, ZnSO4 and Na2SO4 solution. Since the reduction potential Te(IV)/Te(O) is remarkably noble from the solution comparing to Zn(II)/Zn(O), code position of Te and Zn was thought to be difficult from this solution. Resulting from EQCM analysis, furthermore, Te(IV) reduced to Te(O) and Te(-II) in this order so that Te catholically dissolved from the electrode surface at more negative potential. But ZnTe alloy were formed by the UPD of Zn at -0.7V at 298K on Te surface in lmM K2TeO3, 100mM ZnSO4 and 100mM Na2SO4 solution adjusted at pH 4. Content of Te in the deposits is, however, more than 80%.Electrolytic temperature is well known to affect on the deposits characteristics. The higher bath temperature was, the better ZnTe crystal was detected in this study. Thermal electrode method is a. process of heating only substrate by flowing ac current in substrate. This process makes the surface temperature of substrate higher than boiling point of the solution, 373K. From EDX analysis, deposits without thermal current were Te-rich, Te content in the deposits with thermal current decreased with increasing of thermal current. Te content was 62% for 5A ac current, 51 % for I OA and 45% for 20A, respectively. The deposits that produced with ac current of IOA were closed to the stoichiometric ratio, i.e. ZnTe.Consequently, thermal electrode method is more effective to obtain a good crystallized ZnTe without heat treatment after deposition.IntroductionThe current subject of solar cell materials is silicon. Compound semiconductors including GaAs and II-VI group are generally used in the developing field of digital information such as the rapid cellular phone and car telephone. Compound semiconductors consist of more than 2 kinds of element. There are many materials for these compound semiconductors such a SiC, InSb, CdS for binary system and CuinSe2 for ternary system. It becomes generally difficult, to produce high quality crystal with increasing of kinds of element due to a complicated structure and a compound ratio of element. Semiconductor materials as a device are usually simple binary compounds and/or these mixed crystals. Properties of compound semiconductors have variety of the forbidden band and lattice constant and that can be change easily by addition of another element for the usage of the solar cell. Since most compound semiconductors are direct interband transition type, which has steep optics absorption edge and large light absorption coefficient."

Jan 1, 2000

By Alex I. Kociubczyk, Wilky Desrosin, Lucía Mabel Boycho, Alicia E. Ares, Carlos E. Schvezov

In the present research, commercially pure Sn and Zn, and Sn-Zn alloys (Sn-1wt.%Zn, Sn- 2wt.%Zn, Sn-4wt.%Zn, Sn-8wt.%Zn and Sn-8.9wt.%Zn, weight percent) were obtained by a horizontal directional solidification process with two opposite senses and heat extraction. The solidification process was realized using a horizontal furnace with two heat extraction systems at both ends. The temperature was measured using eight K-type thermocouples and an electronic recorder of temperature data. The resulting structures were analyzed using optical microscopy. From the solidification process the thermal and metallographic parameters were determined in all samples. The presence of defects in the solidified pieces was observed. Internal defects pretended to be dependent not only on the composition of the alloys under consideration but also on the size of the structures formed, also, on the velocities and accelerations of interphases, and on the variation of thermal gradients. A model of the phenomenon from the first principles is presented.

Jan 1, 2015

By Ray Y. Lin, Sunil G. Warrier

"Low cost processing of metal matrix composites is an essential requirement for this class of materials to be acceptable in commercial application. In an effort to reduce the cost of processing of metal matrix composites, an infrared pressureless liquid infiltration technique has been developed. The salient features of infrared infiltration are that it is rapid, simple and a low cost process. The rapid processing capability causes very little oxide formation on the alloy resulting in both improved wetting and flow characteristics and reduced oxygen contamination in the composite. Thus, vacuum is normally not required. Using infrared inflltration, aluminum and titanium matrix composites have been prepared under an ambient argon atmosphere. Reinforcements in these composites include carbon fibers, silicon carbide Nicalon fibers and Textron's SCS fibers. Microstructural and mechanical test results indicate that completely consolidated composites with good fiber distribution, limited interfacial reaction and high mechanical properties can be manufactured by this process. IntroductionAluminum and titanium matrix composites reinforced with ceramic reinforcements are strong candidates for numerous applications in the aerospace and automotive industries. Aluminum matrix composites are commonly fabricated by either solid state vacuum hot pressing, liquid state pressure infiltration or squeeze casting [1]. Although liquid state pressure infiltration and squeeze casting has significant advantages over solid state processes, the requirement for pressure makes these composites uneconomical for large scale industrial application. Titanium matrix composites are primarily fabricated by solid state diffusion bonding [2]. Pressureless liquid infiltration can significantly reduce the cost of fabrication in both the composite systems. However, during pressureless infiltration processes, several complications concerning the wetting characteristics and chemical compatibility arise."

Jan 1, 1994

By A. A. Hejja

The first part of this study deals with the importance of surface tension of slags produced in the smelting of sulphide concentrates. Theoretically the method of determining the surface tension of slags was laid down by Boni and Derge. The values obtained experimentally for a series of main oxide components were grouped into a useful correlation incorporating experimental constants for the relevant oxides present in the slag, some of these giving the surface tension value for the particular slag. These estimated values were coupled with or incorporated into the slag viscosity plots to show the correlation between the two factors. This is also important from a refractory attack point of view in the furnace operation. In the second part an attempt is made toward the optimisation of slag composition relevant for electric furnace smelting processes. Using the knowledge of the viscosity and electrical conductivity of the slags at the temperature of furnace operation, the mode of optimisation is based on correlations which utilize the trend of the mostly parabolic plots of viscosities and conductivities. The results obtained by this method agree well with the optimum slag compositions being used in established operations derived from years of practical experience for various slags used in the furnaces. However, due to extensive turbulence in suspension and gas injected bath smelting processes, the outlined methods cannot be used for these processes. Also great caution should be exercised in their application for three electrode circular furnaces with separate slag cleaning.

Jan 1, 1997

HW Process Technologies, Inc. (HWPT) has developed a patented membrane-based ion fractionation system, which specifically separates copper from gold and silver species in a cyanide matrix. This Engineered Membrane Separation (EMS?) system was pilot demonstrated on the 82,000 liters of pregnant leach solution' (PLS) generated from tailings, via thin layer leaching, at a mine site in Durango State, Mexico. The EMS? recovered ~90% of the gold-silver cyano-complex to a 90% volume permeate (based upon an EMS? feed stream of 100% volume) while rejecting -90% of the copper cyano-complex to a \0% (by volume) concentrate. The EMS? technology combines pore-size specific electro-statically charged membranes with engineered materials of construction and application-specific operational design that reject multi-valent, ionically charged species to the concentrate and transmit mono-valent species through the membrane to the permeate. The 850 ppm Cu PLS contained approximately 0.8 gil free NaCN with, the copper cyano-omplex principally in the CU(CN)3 and CU(CN)4 forms. The gold grade of the PLS was -2 ppm Au. The ~LS calcium concentration at -700 ppm Ca was reduced to ISO ppm.Ca (± 50 ppm) by sodium cycle ion exchange pre-treatrnent prior to EMS? processing.

Jan 1, 1998

By Ho Jung Heo

The proper control of slag composition is a dominant factor affecting yield of iron as well as dephosphorization efficiency in an electric arc furnace (EAF) operation. Moreover, thermophysical properties of slags such as viscosity are strongly affected by the changes in slag composition. Slag foaming, which is also a function of viscosity, is directly connected with the yield of iron and thus optimum slag chemistry are highly required in view of thermodynamics and physical properties. Therefore, we analyzed the slag composition in commercial melt shop (70 ton EAF) with the aim of higher yield of iron as well as higher dephosphorization during EAF process.

By James D. O, DeLa&apos

Multicomponent materials are common in nearly all areas of materials science and technology, yet the use of phase diagrams to represent these complex systems is hampered by the requirement of three or more dimensions for explicit graphical representation. In the present work, the "solid-modeling" capabilities of a computer aided design (CAD) system have been applied to the representation of three-dimensional phase diagrams. Relevant phase diagrams for a hypothetical quaternary eutectic system were constructed and used to demonstrate the capabilities of the technique. These capabilities lead to relative ease of phase diagram construction and improved access to qualitative and quantitative information. Results of this work are contrasted and compared to previous efforts toward computer ,representation of phase diagrams. It is concluded that solid-modeling of three-dimensional phase diagrams can be used to advantage in both education and research.

Jan 1, 1991

By Charles W. Kenney

Mercury contamination of soil at an old chemical plant surrounded by a residential community and adjacent to a river has provided unique challenges for the current owner. Inorganic and organic mercury compounds had accumulated over the past 50 years to levels that require remediation. Hazen Research, Inc. conducted a multi-phased program to characterize contaminants and their occurrences, evaluate various treatment technologies, and demonstrate the selected technology at bench and pilot scales. A combined physical cleaning and chemical treatment was demonstrated to meet treatment goals for the site. This paper discusses the methods of process selection and results of the bench-and pilot-scale testing.

Jan 1, 2003

By C. Y. Tang, Z. H. Chen, T. C. Lee

"In sheet metal forming process, the forming limit and strain distribution are governed by plastic instability and fracture following strain localization. It has been proved that the temperature gradient caused by plastic deformation as well as friction is one of the crucial factors to induce the strain localization in high-speed metal forming processes. In this paper, a numerical simulation of the sheet metal extrusion process has been conducted by using thermal-mechanical coupling finite element method. An improved mixed finite element method has been used to solve the large deformation elasto-plastic problem. In thermal phase, the transient heat transfer finite element method together with the Crank-Nicholson algorithm has been employed to determine the temperature field. Both the numerical results and the experimental observations reveal that the temperature gradient plays an important role in inducing the strain localization, which eventually leads to fracture failure in the sheet metal extrusion process.IntroductionSheet metal extrusion is such a process where the extrusion punch penetrates into one surface of the sheet metal material to let it extrude and flow towards the outlet of the die. This process can be used to produce protruding parts on a strip material. In engineering applications, the quality of the product is affected by many factors such as stress state, loading speed, material properties and lubrication condition. The research on failure mechanisms and improvement of formability in sheet metal forming processes by exploitation of differential thermal conditions has been of great interest recently [1-3]. It has been proved that the temperature gradient caused by plastic deformation, heat transfer, and friction between sheet and tools is one of crucial factors to affect 'the formability in high speed sheet metal forming processes [4]. In our previous study of sheet metal extrusion, it has been observed that plastic deformation is highly localized and some specimens are subjected to fracture failure in the form of crack propagation [5]. To understand this failure phenomenon, the effects of temperature gradients must not be ignored."

Jan 1, 2001

By Toshiaki Akahoshi

Keywords: Wasted catalyst, Hydrodesulfurization, Ammonium vanadate, Ammonium molyb-date, Hydrometallurgical process. The fundamental reactions have been investigated in order to develop a hydrometallurgical process for recovery of molybdenum and vanadium from wasted catalysts generated in the hy-drotreating desulfurization of heavy oil. The principal steps of the process are a mild oxidation roasting of the waste catalysts at temperature around 500°C, leaching of the target metal components with dilute ammoniacal aqueous leachates, selective precipitation of vanadic acid, and ammonium molybdate precipitation. The selective recovery of vanadium as vanadic acid is successfully performed using ammonium sulfate as a salting-out agent. Recovery of ammonium molybdate is based on large dependence of solubility of ammonium molybdate in ammoniacal solutions upon temperature and ammonium salt concentration. In this process, the solution after recovery of vanadium and molybdenum is recycled to the leaching stage of the roasted materials, and the ammonium salts in the process liquor is in the repeated use. Employment of am-moniacal system makes it possible to operate the roasting at much lower temperature than that for the currently operating process.

Jan 1, 2005

By M. B. Sizgoric

Quantitative mineralogy is used in a study done on an Inco Metals Company nickel sulfide occurrence from 'the Thompson area in Northern Manitoba. The study included: a) determination of the variations in chemical composition of the ore minerals; b) determination of the liberation of the ore minerals for the various types of ore and for different feed grinds; c) assessment of the preliminary mill test results by comparing the mineral distribution in the different tailings. Preliminary mill test results had outlined three main problem areas: 1) unacceptabiy low grade concentrate with, 2) very high weight recovery and, 3) low pyrrhotite rejection resulting in a high sulfur concentrate. The mineralogical study readily explained these results by showing that: 1) between 20 and 40% of the nickel in the feeds and 55 and 75% of the nickel lost in the tailings is associated with pyrrhotite. This accounts in part for the low grade of the concentrates obtained at high recoveries: 2) hexagonal nonmagnetic pyrrhotite constitutes over 90 percent of pyrrhotite. Since hexagonal pyrrhotite floats more readily than monoclinic pyrrhotite, this could be part of the reason for the undesirable high pyrrhotite recoveries into the concentrates. Further test work to establish both the optimal grind and the best conditions for pyrrhotite rejection is therefore mandatory.

Jan 1, 1981

By Tom Marttila

During the last few years, when a new tankhouse or a major modernization has been planned, automatic or semiautomatic crane and grab systems have at least been considered. It seems that in the future tankhouse managers for new, modernized and even old tankhouses will be looking for a proven and reliable system for automatically moving and positioning electrode loads in the tankhouse and in storage areas. In this paper, we will describe the Wenmec solution for automatic electrode handling. The advantages of automatic handling and very accurate electrode positioning will be discussed, and the way Wenmec has solved the problems in mechanical construction and in automatic, accurate and reliable positioning will be presented.

Jan 1, 1990

By Georges J. Kipouros

Anhydrous neodymium trichlorids (NdCl3), containing ~1 weight percent neodymium oxychloride (NdOCI) was prepared by the dehydration of neodymium trichioride hexahydrate (NdC13.6H2O). Dehydration of the hexahydrate was conducted in three steps. First, the hexahydrate was slowly heated in air to about 250 °C until all the low temperature water of crystallization was removed. In the second stop, the neodymium hydroxychloride (Nd(OH)2C1) fanned in the first step was decomposed by heating under argon to 430 ° C. Finally the salt was ground and then treated with HCl gas at 330 °C until practically all of the NdOCl was converted to NdCl3.

Jan 1, 1992

By Juliana Gutiérrez-Paredes

Keywords: Slag, chromium oxide, recovery, stainless steel Experimental and theoretical work was performed to estimate the effect of slag basicity and amount of reducing agents on the reduction of chromium oxide from the slag which interacted with molten steel at 1600°C. The slag system contained CaO, MgO, SiO2, CaF2 and Cr2O3 together with Fe-alloys (Fe-Si and Fe-Si-Mg). The CaF2 and MgO contents in the slags were 10 mass % each; Cr2O3 was 25%. The amount of the ferroalloys ranged from 12.5 to 50 g per 100 g of slag. The (CaO+MgO)/SiO2 ratio was held at 1 and 2. The Cr yield was determined using both Fe-alloys as reducing agents. Some estimations were made to determine the theoretical effect of temperature, slag basicity, (CaO+MgO)/SiO2, and amount of reducing agents in the slag on the chromium recovery. The FACT (Facility for the Analysis of Chemical Thermodynamics) computational package is used to determine the equilibrium between the slag and molten steel.

Jan 1, 2005