Search Documents

By Bo Zhou

During secondary aluminum recovery, complex aluminum scraps are melted and refined often in a rotary melting furnace and the aluminum metal has to pass through a molten salt layer and melt down in a bottom aluminum bath. Previous experimental study and industrial observations have indicated that salt shell formation and re-melting on the metal solids in the early stage plays a critical role in the overall melting process of the scrap. In the present paper, mathematical models are developed to simulate the process of salt shell formation and its re melting, as well as aluminum melting in the molten melt. Influence of the salt layer properties, the residence time of the metal particles in the salt layer, the particle size, the temperature of bulk melt were investigated. Reasonable agreement with the measurement data was reached. The developed melting model will be used to construct a population balance model of the scrap melting behavior for a rotary melting furnace, taking into account the distributed characteristics of the scrap. Finally, an overall process model based on Computational Fluid Dynamics (CFD) for the rotary furnace will be constructed, coupling with the population balance model for the scrap melting.

Jan 1, 2003

By Huimin Lu, Liyuan Zhao, Zhijiang Gao

The aluminum matrix composite reinforced by graphene was successfully fabricated using high pressure torsion (HPT). With only 0.5wt% graphene, the grain size was reduced to 100nm while that of pure Al was about 500nm. The hardness of the composite increased from the center (64HV) to the edge (120HV) of the sample. Moreover, the tensile strength of this composite reached 197MPa, while that of pure Al was 157MPa. The enhancement in mechanical properties was induced by grain refinement, load transfer from the matrix to the reinforcement and dislocations piled up at the grain boundaries.

Jan 1, 2015

By A. M. Strachan

Capper Pass & Son Limited Was, until its recent closure, the world's largest producer of tin from secondary materials including solder drosses, non-ferrous smelter flue dusts, tin based metal alloys, residues and slags. Polonium-210, an alpha emitting radionuclide, was present in varying concentrations in some of the numerous feed materials processed by the smelter and refiner. The polonium-210 followed a complex path through the process flowsheet. This paper discusses the behaviour of polonium, both from its arisings in other smelters' process streams and through the entire Capper Pass smelting and refining circuit. The consequential personnel safety and environmental precautions necessarily taken in some areas of the process operation are outlined.

Jan 1, 1992

By Joseph Sofra

It has become increasingly evident that sustainable metals production in the 21st century requires producers to balance the needs of cost effective, high value production with that of responsible plant operation. This is becoming more difficult as lower grade and more complex feed materials, including recycled scrap and residues, are being processed to reduce production costs and decrease exposure to primary metal market fluctuations. One particular facet of the metals industry facing these challenges in the 21st century are copper producers, The recent steady decline in the copper price has seen the industry cut expenditure, tighten control on income streams and focus on high returns on capital investment. For these reasons copper producers are looking towards flexible technologies that can deliver high value products, with minimal environmental impact at low capital and low sustainable operating costs. Ausmelt's Top Submerged Lancing (TSL) technology for copper production is a low cost, proven technology for the processing of both primary and secondary copper materials. Both the smelting and converting operations introduce significant advantages in environmental performance, improved process efficiencies and high rates of metal recovery, Ausmelt has made significant gains in the past 4 years in establishing a strong market position for its copper technology, New installations in China, South Africa and India as well as existing operations in Zimbabwe and China have demonstrated its effectiveness. This paper reviews the application of Ausmelt Technology for both smelting and converting of primary and secondary sources, It discusses Ausmelt's design and implementation philosophy, and how this philosophy meshes with the needs of the end user.

Jan 1, 2003

By Huanyu Zhang, Zhancheng Guo, Liqiang Fan, Huiqing Tang

"In this study, a simple process has been developed for zinc oxide recovery from RHF (rotary hearth furnace) secondary dust. The results have shown that a high dissolution efficiency of soluble zinc was achieved with water leach at ambient temperature with a liquid/solid ratio of 10/1 in 30min while 20% of the dust was left as solid residue. The rate of dissolution increased slowly after the dissolution efficiency reached 90%. The leaching process was found to be controlled by external diffusion. After separation, zinc was precipitated in leached liquor by introducing a precipitation agent of potassium hydroxide. The resulting solid was purified and dried at 393K. Zinc powder in the form of ZnO with purity of 98.5 mass% was obtained with an average size of 12.4µm.IntroductionThe RHF (rotary hearth furnace) direct reduction process is widely used in many iron and steel enterprises to deal with various metallurgical dusts [l]. The basic principle of this process is that first various metallurgical dusts (BF dust, EAF dust and so on) are pelletized with a coal reductant, and they are then subjected to a fast reduction using RHF after being dried. Highly metallic pellets are produced and at the same time, nonferrous elements such as Zn, Pb, K and Na are evaporated into the RHF flu gas as secondary dust. Zinc is listed by the Enviromnental Protection Agency as one of the 129 priority pollutants. Therefore, recovering zinc from the industrial wastes is important in terms of enviromnental protection [2-3]. On the other hand, nowadays China is in shortage of zinc resource and the annual output from metal recycle only accounts for some 13% of the total zinc resource. There are many ways proposed to recover zinc from various wastes [ 4-7]. The aim of this paper is to recover zinc oxide from RHF secondary dust by a method with water leach followed by caustic precipitation. This work investigated the influence of the leaching temperature and leaching liquid/solid ratio on the zinc recovery efficiency. The process consisted of three stages: (1) leaching with water; (2) liquor/residue separation; and (3) zinc precipitation in caustic milieu."

Jan 1, 2014

By Zhucheng Huang, Zhikai Liang, Lingyun Yi, Tao Jiang

"In this study, reduction of iron ore pellets was carried out at 800-950°C by simulating the atmosphere of typical coal gasification gas. The effects of temperature, gas composition and reduction degree on swelling were investigated respectively. Reduction degree was obtained according to the weight loss records. And volume changes of pellets during reduction were evaluated by infrared photography. Results showed that the pellet swelling increased with temperature and decreased slightly with hydrogen content in the reducing gas. The swelling peaked when reduction degree reached about 40% and then decreased to be stable finally. The microstructures of pellets during reduction were examined by reflected light microscope and relatively rational explanations were proposed for their swelling behaviors.PrefaceDirect reduction iron is an important and indispensable raw material for high-purified and high-quality steel in the electric furnace smelting. Gas-based shaft furnace direct reduction process has very strong competitative ability; however, this technique requires natural gas as reducing agent, so its development has been restricted by gas source and area. Compared with gas-based reduction method, coal based reduction method has the disadvantages of higher production cost and lower productivity. In China, coal resources are abundant and coal gasification technology is mature, and the development of coal gasification shaft furnace direct reduction process is promising. [1] The gasification methods of fixed bed method (Lurgi method), fluidized bed method (Undok method), airflow bed method (Texaco coal water slurry method and Shell dry powder coal method) have been put into use successfully. These syngas generated by different methods can meet the actual production requirement of shaft furnace. However, the compositions of the effective reduction gas in the syngas are quite different. The ratios of hydrogen and carbon monoxide (H2/CO) of Undok or Shell coal gas, Texaco coal gas and Lurgi coal gas are 0.4, 0.6~ 1.0 and 1.6~2.3, respectively. [2] In the coal gas direct reduction process, the swelling behavior of iron ore pellets is various due to the differences of the gas composition, reduction temperature and reduction degree, and it seriously affects the normal operation ofDRI production. [3-9] Therefore, the research on the swelling behavior and its mechanism of iron ore pellets in direct reduction were carried out in this paper."

Jan 1, 2013

By Gerardo Fuentes

The stoichiometry and kinetics of the hydrothermal reaction of enargite in copper sulphate solutions was investigated in the range 140–300 °C, and particle size under 15 and 50 μm. The stoichiometric experiment was performed at 300 °C, using one gram of sample (96% enargite, 4% tennantite) and 100 mL of copper sulphate solution (10 gpl) at 1.2 pH. Enargite reacted completely after 80 min. A solid product was obtained and characterized by XRD. The main product was chalcocite (M) and some traces of djurleite and chalcocite (Q). Tennantite did not react under these conditions. The kinetic experiments were conducted at 140 °C, 190 °C, 250 °C and 300 °C. From fitted data and Arrhenius equation the calculated activation energy (Ea) was 51 kJ/mol. According to the hydrothermal transformations studied, the reactivity of different phases found in the copper concentrates was bornite > chalcopyrite > covellite > sphalerite > pyrite > enargite > tennantite.

By Ryan Walton

The Flash Converting Furnace at Kennecott Utah Copper converted over 465kmt of high-grade matte in 2002 but was restricted due to low matte production to 395kmt in 2003. This paper presents updated operational performance data and describes improvements implemented since the mid 2001 rebuild. Matte burner feed distribution, silica and arsenic impacts on settler lime-based slag operability, blister laundering, uptake/boiler accretion control, and dust sulfation will be discussed, as well as current development requirements dictated by operational imperatives and furnace modification plans.

Jan 1, 2005

By John ?gren, Martin Schwind, Henrik Larsson

"A new model for internal oxidation, as well as similar processes, has been implemented on computer. It is based upon a combination of random walk and cellular automata and is capable of treating 3-dimensional cases. To model diffusion, it utilises quantised units of matter. All steps of the process are included: nucleation, growth and coarsening. The effect of grain boundaries on diffusion as well as nucleation is taken into account. Further possible development is briefly discussed; especially the treatment of nucleation needs further consideration. IntroductionComplex diffusion-controlled processes may now be simulated on a routine basis when concentration varies along one co-ordinate only. One-dimensional simulations capture much of the information of interest but not all. For the case at hand, especially the spatial and the size distribution of precipitates, as well as the impact of grain boundaries, would be interesting information not accessible from 1-D simulationsSolving the full Fick-Onsager law in three dimensions does not seem feasible with the computers of today. In the model described in this article, random walk by quantised units of matter are considered. The model should be useful for a number of cases involving dispersed systems. With further development, it would indeed seem possible to simulate most types of phase transformations.Previous workWe have previously published two articles [1,2] on the new approach discussed in this work. In those articles we described the basic idea and showed, among other things, that very good agreement with an experimental concentration profile can be obtained, in a single-phase system, using independently assessed thermodynamic and kinetic data. Also, Schwind used the same random walk based concept to model coarsening [3]."

Jan 1, 2001

By Chuan-fu Zhang

Li(Nil/3Col/3- xMnl/3)MxO2(M=Ti, Mg) cathode materials were prepared from LiOH?H2O and oxalate precursor. The physical and electrochemical properties were studied by XRD, SEM, cyclic volt-ampere (CV), AC impedance and constant current charge-discharge. The results show that crystal volume of Ti4+ or Mg2+ doped sample is increasing and the electrochemical reaction resistant Rct is decreased at high rate, improving the cyclic performance and rate capability. The effect of Ti4+ doped is better than Mg2+. The sample is well crystallized and simple pure phase with a-NaFeO2 layered structure when doping quantity x=0.025. The second specific discharge capacity of Li(Nil/3Col/3- 0.025Mnl/3)Ti0.025O2 is 143.2mAh/g at 1C,128.0mAh/g at 2C in the voltage of 2.75-4.3V,and still has 140.7mAh/g and 121.7mAh/g after 20 cycles, respectively, keeping 98.25%, 95.07% capacity.

Jan 1, 2009

By Christiana Mystrioti

Greece is the only EU country with extensive nickel laterite deposits. Since the 1960s, the Greek laterites are treated for ferronickel production via a pyrometallurgical route, which involves pre-reduction of the ore in rotary kilns and reduction smelting in electric arc furnaces. Due to the rising cost of energy and the decreasing grade of mined laterites, the pyrometallurgical treatment is economically marginal. For this reason, alternative treatment processes are currently under investigation. Potential applicability of hydrometallurgical treatment, using either H2SO4 or HCl, under atmospheric pressure conditions, for Ni and Co extraction from two low grade laterite ores, was examined in the present work. The two samples were selected to represent the different mineralogical composition of the saprolitic and limonitic ore deposits of the Greek laterites. The investigated parameters were temperature (65–90 °C), acid concentration (1–4 N) and solid to liquid ratio (10–30% w/v). The results indicated that HCl was more efficient than H2SO4 for the treatment of the saprolitic ore; Ni and Co extractions were very high for both elements, up to 98% and 96% respectively, while H2SO4 could leach efficiently Ni, up to 100%, but extracted only 34% of Co. Hydrochloric acid was also more efficient for the treatment of the limonitic ore, with Ni and Co extractions up to 98.3% and 87.6% respectively. With H2SO4 the maximum extractions were 71.3% for Ni and 52.1% for Co.

By G. A. Brooks

Reactive ball milling has been proposed as a new route for producing carbides from oxides through carbothcrmic reduction. It is claimed that through milling oxide and graphite powders to the nanoscale, amorphous materials with very high reactivity are formed, that allows for easy transformation of the starting material to another in a subsequent thermal process. Thermodynamic analysis of this proposed process suggests that unless particle sizes are reduced to below 10nm, then reduction in size alone cannot explain a change in the stability of oxides. Even with nanometer scale powders, the products formed need to have a lower total surface energy than the reactants before a chemical change will occur. A model developed by Bhattacharya and Arzt for predicting localized temperature changes based on milling conditions suggest that temperarure rises less than 400 K will be achieved in laboratory conditions. The present calculations suggest that nanometer scale powders formed through high speed ball milling (>10 mls) may have undergone a process analogous to melting and quenching. Further work is required to fully distinguish these features.

Jan 1, 2003

By S. P. Song

A computational methodology based on the coupled finite element and boundary methods is developed to predict the free surface shapes of electrically conducting liquids supported by the electromagnetic field. The work is an extension of our previous FEIBE model for induction calculations. The free surface algorithm is developed using the Weighted Residual Method, the very same used for nonlinear finite element formulation. This allows the treatment of field computation and free surface prediction in the same manner, thus making easier the formulation of the magnetically-supported free surface problems. Like other nonlinear algorithms, the boundary/finite element free surface scheme is also iterative owing to the fact that free surface shapes are unknown a priori. But the numerical scheme is robust and efficient and is capable of handling rather complex free surface deformations. Computational algorithms will be given and are tested by comparing with other solutions whenever available. Computed results of magnetically-supported free surface shapes are presented for magnetic levitation under microgravity and floating zone refining processes under normal gravity.

Jan 1, 1996

By A. Galvan

High rate compressible media filter (CMF) tests produced exceptional total suspended solids (TSS) removal at hydraulic loading rates ranging from 97.8 to 122.2 m/h. The compressible media is manufactured from a robust resin fiber that can withstand low pH and temperatures up to 149 °C. The media porosity can be varied by applying compression onto the media. At 40% compression, the CMF can remove particles greater than 4 μ. Three synthetic test-samples were generated by Hazen Research Inc., (Golden, Colorado) to simulate the copper Pregnant Leach Solution (PLS), Raffinate and Electrolyte solutions used for the testwork conducted at their facility. The preliminary results showed that the CMF was very effective in removing TSS without the use of chemical conditioning from the above test-solutions with efficiencies of 98%, 97%, and 96%, respectively. Given the remarkably high hydraulic loading rates, the industrial equipment footprint would be minimized appreciably over conventional clarification and alternative filtration systems.

By G. A. Brooks

Reactive ball milling has been proposed as a new route for producing carbides from oxides through carbothermic reduction. It is claimed that through milling oxide and graphite powders to the nanoscale, amorphous materials with very high reactivity are formed, that allows for easy transformation of the starting material to another in a subsequent thermal process. Thermodynamic analysis of this proposed process suggests that unless particle sizes are reduced to below 10nm, then reduction in size alone cannot explain a change in the stability of oxides. Even with nanometer scale powders, the products formed need to have a lower total surface energy than the reactants before a chemical change will occur. A model developed by Bhattacharya and Arzt for predicting localized temperature changes based on milling conditions suggest that temperature rises less than 400 K will be achieved in laboratory conditions. The present calculations suggest that nanometer scale powders formed through high speed ball milling (> I 0 mls) may have undergone a process analogous to melting and quenching. Further work is required to fully distinguish these features.

Jan 1, 2003

By Keith E. Forrester

This paper presents results of laboratory and field optimization of a proprietary processes developed by FESI for the stabilization of heavy metal bearing wastes. The specific waste studies presented within the paper include foundry ash, aluminum sweat furnace ash and a heavy metal contaminated soil. The FESI process chemistry and engineered processes were found to be the most cost efficient demonstrated and available method of stabilizing heavy metals and highly successful in passing regulatory limits.

Jan 1, 1994

By Maria D. Salazar-Villalpando, Anthony Cugini, Bryan Reyes

"The electrochemical reduction of CO2 was performed in a laboratory-made, divided Htype cell. A copper electrode was used as the cathode. An Aldrich Nafion 117-type ion exchange membrane (0.18mm thickness) was used as the diaphragm. NaHCO3 and KHCO3 were studied as the catholytes. Hydrogen evolution from water reduction and products from CO2 electrochemical conversion were recorded. Higher CO2 reduction enhancement was observed by KHCO3 as compared to NaHCO3. The main conclusion of this work is that in fact CO2 can be electrochemically reduced with copper electrodes.1.-INTRODUCTIONThe direct electrochemical reduction of CO2 may allow for a simple process and, by avoiding high temperature reactors, would enable the process production rate to be quickly varied to follow the time of day availability of surplus electricity [1]. Temperature has a major effect on the electrochemical conversion of CO2 since its solubility increases when temperature decreases [2]. The electrical potential applied to the electrochemical reacting system will have an influence on the product distribution, as well. For example, a narrow potential range during cyclo-voltagraphic studies will determine the detection of a lower number of products. A recommended potential range to study the electrochemical reduction of CO2 is -2V to 2V. Moreover, the reaction rate on the electrode is governed by various processes, such as the kinetics of electron transfer, adsorption/desorption at the electrode surface, and diffusion of CO2 to the Cu electrode. The availability of active species, CO2 for electro-reduction, is extremely low at the vicinity of the electrode surface and it seriously interferes with the rate of mass transfer. In batch type electrolytic reactors, depletion of CO2 at the surface takes place first. CO2 from the bulk then has to diffuse to the electrode surface, resulting in mass transfer controlled kinetic phenomena. During the above process, several other competitive side reactions could suppress the primary reaction even though the cathode has good electro catalytic properties for reduction of carbon dioxide. When the dynamic supply of specific active species is ensured to electrode surface, the mass transfer effects are minimized to certain extent. Hence it is envisaged that a continuous flow reactor is more efficient for the electro-reduction of CO2 in CO2 saturated aqueous electrolytes. The primary reactions that occur at the copper electrode during the reduction of CO2 are listed below (with the standard potentials calculated using formation energies [1] :"

Jan 1, 2010

By Sebastian Schmuck, Petrico von Schweinichen, Dieter Senk, Mohammad Peymandar

"At Department of Ferrous Metallurgy of the RWTH Aachen University in Germany steels in the system Fe-Mn-C(-Al) are investigated and produced in the framework of the SFB 761 ""steel-ab initio"". A new world of steel grades leads to special challenges regarding the production and recycling at the end-of-life cycle of product. In order to recycle high manganese steel alloys the EAF has to be chosen preferentially. A good slag practice is necessary avoiding loss of manganese content during melting in the EAF. This paper investigates on the reaction kinetics at the interface of slag and steel containing Mn (17-22 wt.-%) and up to 3 wt.-% Al. The effect of changes in the composition of slag and steel on the interfacial reaction kinetics is studied. The thermodynamic software FactSage™ is utilized to calculate the composition of slag and steel at equilibrium.IntroductionTRIP and TWIP steels are highly alloyed steels which show superior strength and ductility when compared to standard carbon steel and stainless steel alloys. These TRIP- and TWIPsteel grades contain typically 15-30 wt.-% manganese, 0-4 wt.-% silicon and aluminum, and up to 1 wt.-% carbon. Steels containing 18-28 wt.-% manganese and 0.7-1.2 wt.-% carbon together with aluminum addition from 3 to 12 wt. -% and without silicon refer to TRIPLEX high manganese steel alloys. These alloys combine high strength at even large ductility [ 1-4]. At the Department of Ferrous Metallurgy (IEHK) of the RWTH Aachen University in Germany, steels in the system Fe-Mn-C(-Al) is under investigation at the collaborative research center, SFB 761 ""Steel-ab initio"". In this project, high manganese alloyed TRIP and TWIP steels are in the focus.The mechanical properties such as high strength and high ductility make this kind of steels perfect candidates for impact absorption applications in auto body such as vehicle doors and bumpers [2, 5]. With increasing the use of TRIP-, TWIP- and TRIPLEX-steels more high manganese steel scraps will be available at the end of life cycle of products, which need to develop the technologies and metallurgical processes to recovery of high manganese steel. A new steel grade brings new challenges in recycling. In order to recycle high manganese steel scraps the electric arc furnaces (EAF) have to be chosen preferentially [1]. Nevertheless it's not easy to prevent the manganese loss during the process in EAF. During the oxygen refining of high manganese molten steel in EAF the manganese content decreases strongly by oxidation and vaporization, which is affected by slag composition, slag properties such as basicity and viscosity, slag weight as well as melt temperature [6-8]."

Jan 1, 2014

By D. W. Hoey

Eight years use of the ISA Process is reviewed and current design and operations described. Nodern Technology used for impurity control and disposal as well as the use of mechanised electrode handling equipment, cell voltage monitoring, cell insulation and an efficient contact bar system are described. Improvements achieved in terms of energy usage and plant productivity are detailed.

Jan 1, 1987

By A. M. Alfantazi, M. Boissoneault, D. B. Dreisinger, J. Synnott

Acid mist generation is a major concern in zinc, copper and nickel electrowinning industries and there is a strong environmental drive to control its emission into the work environment. Foaming reagents are typically added to the electrolyte to alleviate this problem. In zinc electrowinning, Licorice and Saponin are examples of foaming reagents used for this purpose. In order for the foaming reagent to be effective, its foaming behavior must be determined. In this work, a test procedure was developed to study the foaming characteristics of various surfactants for use as foaming agents to control acid mist in aqueous metal electrowinning. This new test was termed as "mini-flotation test" and it was used to study the foaming behavior of a large number of reagents in an industrial zinc sulfate electrolyte under simulated zinc electrowinning conditions (gas sparging). In addition, the influence of important process parameters such as current density, electrolyte temperature, reagent addition level and sulfuric acid concentration on the foaming characteristics of the electrolyte for each surfactant were investigated. The results of this study have identified the most important factors that influence foam formation, growth and stability. This method could be used as a process control for reagent addition in the cellhouse by generating a calibration curve for the optimum electrolyte conditions.

Jan 1, 1997