Search Documents

By John Wallace

"Monitoring compound semiconductor crystal growth using multifrequency eddy currents for sensing illustrates some of the extreme problems of measurement and interpretation that are not often seen in metallic systems. Using sensor arrays and scanning sensors have produced a qualitative and quantitative understanding of some of the high temperature electrical conductivity mechanisms in several compound systems. A detailed review of the CdTe/CdZnTe data is presented showing some of the complexity in the data as opposed to what is found in elemental semiconductors.HistoryThe most common goal in the use of eddy current measurement in crystal growth is to deter-mine the curvature of the liquid solid interface during growth to test if the heat transfer estimates of the thermal design were adequate for single crystal growth[l]. This aim could be met but represented only a small fraction of the data that was produced observing a growth cycle. A secondary consideration was what could be discovered in the recorded data about the growth and subsequent heat treatment as the boule cooled. This is usually a more difficult task because a crystal growth process is not a controlled experiment so much as a process that continually sees modification. Using a sensor arrays or a scanning loop has produced a qualitative and quantitative basis for understanding some of the high temperature electrical conductivity mechanisms. The implication of the these measurements of electrical conductivity variations are important in that they reflect the complex defect states that will occur on cooling and heat treatment following crystal growth. In contrast to the complex behavior of the conductivity of these compound semiconductors in the solid and liquid state we have the very well characterized system silicon to compare. Initially the interest on using eddy currents to monitor compound semiconductors came from G. Westphal at the Texas; Instruments Company in 1987 to monitor aspects of growth and compounding of GaAs. This was followed by work on solution growth of HgCdTe with D. Witter. The initial interest in the use of eddy cur-rents for monitoring CdTe crystal growth came from Prof. Wilcox at Clarkson University in the practical interest to determine and control the crystal interface curvature during vertical brigdeman growth. The first actual work was done by one of his former students. G. Neuge-bauer at the II-VI Corporation which was carried on by G. Rosen at Clarkson and R. Shetty at II-VI Corporation and with A. Socha at Johnson-Matthey Electronics. The work on CdTe extends over four years and yielded sufficient data to allow one to evaluate the utility of the information produced as compared to what could be obtained from monitoring an elemental semiconductor such as silicon."

Jan 1, 1997

By B. Wasmund, K. Adham, K. O'Keefe, C. Lee

"Metal chlorides (e.g. iron and nickel) can be pyrohydrolysed at elevated temperatures to yield an HCl rich off-gas and a metal oxide product. Typically, the high energy requirement for pyrohydrolysis is provided by the combustion of a hydrocarbon fuel with air. Here, it is demonstrated that the use of oxygen-enriched combustion can result in lower fuel requirements and higher HCl concentrations. In addition, the oxygen enrichment can result in a smaller volume of off-gas and thus, smaller and less expensive process equipment. This new concept can be applied to both the spray roaster (SR) and the fluidized bed reactor (FBR). Similar to the aircombustion case, the oxygen-enriched process can use a direct contact venturi scrubber, to recover energy from the roaster off gas, but at a higher efficiency. The new process also uses an absorption tower for capturing HCl from the roaster off-gas, but generates a stronger HCl solution than is possible with pyrohydrolysis in air.BackgroundIn recent years, the metallurgical industry has become increasingly involved with developing methods for extracting metals, upgrading products or cleaning metallic products by using hydrochloric acid. These applications of chloride metallurgy often result in metal chloride solutions, which should be processed to regenerate HCl for reuse, and to recover the metal value as a product or by-product oxide [2, 3, 4].The pyrohydrolysis of metal chloride solutions has been done in two types of air roasters: spray and fluidized bed. The existing roasters burn a hydrocarbon fuel in air, to provide the required energy for evaporating the feed solution and to provide an elevated temperature for the chloride pyrohydrolysis to occur, according to the following reactions:"

Jan 1, 2011

By Feng Gao

A general unsteady- state model, based on a cracked substrate, has been developed to account for reaction and diffusion within porous substrate during oxidation of Carbon Fiber Reinforced Carbon matrix (CIC) composites. The effects of several parameters, such as diffusion and reaction rate ratio, oxygen concentration, and composite density, on oxidation process are explored. Also, theoretical results for a set of parameter values of the CIC composites are compared with experimental data. It shows that the model predicted values agreed well with the experimental data in weight loss. Based on this model, quantitative predictions of oxidation of a composite with cracked substrate can be made.

Jan 1, 1993

By Jong-Jin Pak

The present work reports the commercialization of a recycling process of spent acid to recover molybdenum. The process consists of ammonia gas neutralization of spent acid containing molybdenum, crystallization and filtration of ammonium molybdate, roasting and hydrogen reduction of molybdic oxide to produce a commercial grade molybdenum metal powder. The mother liquor, highly nitrogeneous residual solution after the filtration of ammonium molybdate, can be utilized to produce chemical fertilizers.

Jan 1, 2006

By C. Leticia Hernández, P. Martín Reyes, D. Iván Alejandrox Reyes, L. Miguel Pérez, T. Julio Cesar Juárez, G. Mizraim Uriel Flores, T. Raúl Moreno, R. Aislinn Michelle Teja

This study shows the characterization of tailings from the mining district of Coscotitlán, State of Hidalgo, Mexico. Chemical analysis by Spectroscopy of atomic absorption (AAS) allowed to quantify the concentration of Fe, Mn, Zn, and Pb as the most abundant elements in the mineral sample; in addition to the presence of Sn, Te, Bi, Ni, Co, and Cd. The presence of precious metals as the Ag (64 g ton−1) and Au (0.65 g ton−1) were identified. The greater distribution of Ag was detected in particles with diameter of 74 lm. Species as pyrite (FeS2), galena (PbS) and hematite (Fe2O3) were observed in a matrix of quartz (SiO2) by Polarized Optical Microscopy (POM), these species were also identified by X-ray Diffraction (XRD). Both the elemental and mineralogical composition of tailings was corroborated by the technique Scanning Electron Microscopy - Energy Dispersive Microanalysis (SEM-EDS).

Mar 1, 2018

By Zhenfeng Zhou, Qingguo Xue, Jingsong Wang, Guang Wang, Yuanyuan Zhang

The oxygen blast furnace is a new technology for ironmaking, where the oxygen and CO2-stripped blast furnace top gas are blown into the blast furnace replacing the conventional hot air. The oxygen blast furnace could reduce the consumption of coke and emission of carbon dioxide. In this chapter, a three-dimensional numerical model was developed to simulate the lance-blowpipetuyere-raceway region of a blast furnace, and the flow and combustion behaviors of coal particles were investigated based on an oxygen blast furnace. Compared with the traditional blast furnace, the combustion characteristics in the raceway of the oxygen blast furnace were different. In addition to the combustion of coal and coke, the combustion of large amounts of reducing gas was included. The coal combustion of different oxygen content (70, 80, 90, 100%) were investigated. The simulation results indicated that the coal burnout was only 21.64% at an oxygen content of 70%, a decrease of 51.52%, compared with a traditional blast furnace. The coal burnout was increased with the increase of oxygen content. When the oxygen content is 100%, the coal burnout was 90.38%, an increase of 17.22%.

Mar 1, 2017

By Kunwar Pal, S. K. Tyagi, A. K. Pandey

"This study deals with the performance evaluation, technical and environmental aspects of different cookstove models (NIRE-02, NIRE-03 & NIRE-04). These cookstove models were designed, fabricated and evaluated following Bureau of Indian Standards (BIS) and their performance was compared from technical and environmental points of views. The theoretical efficiencies of all the cookstove models are found to be in good agreement with the experimental one. Also, the overall performance of these models is found to be in the order of (NIRE-04 > NIRE-03 > NIRE-02) which is also observed to be much better than that of the traditional cookstoves being used by the people in most of the developing countries around the world. The CO2 emission reduction from these models is found to be between 2.0-3.0 tons per household annually which is ultimately in good agreement with the experimental values.IntroductionMore than 2.5 billion people around the world depends on the biomass based resources for cooking and heating applications which includes wood, cattle dung, charcoal and agriculture residue [1,2]. Generally, people of rural area cook their food on unvented open fire, which burn biomass fuel inefficiently besides it creates many thermal and environment pollution hazardous causing health problems in the women and girl children due to more exposure of emissions. Also the consumption of biomass is very high as compared to the fossil fuels due to the fact that the large population of the developing countries lives in the rural area than that of in the urban area. It is estimated that about 3% of the diseases are caused due to incomplete combustion of biomass, which results in the around 1.8 million premature death every year including around 0.9 million death under five year of their age [3,4].Ramanathan and Carmichael [5] recently found that the black carbon of unburned smoke is playing a major role in global warming. The emission factors for different combinations of fuel and stove tested in China for direct and indirect GHGs as well as other airborne pollutants such as, CO2, CO, CH4, TNMHC, N2O, SOx, NOx, TSP etc. for a typical set of operating parameters [6]. The improved biomass cookstove technology came into assistance which is technically feasible, socially reliable and economically viable [7, 8]. The improved biomass cookstove not only reduces pressure on the biomass resource, but also reduces the environmental pollution and also minimize the time required for collection of fuel wood [9, 10]. Sharma et al. [11] emphasized on the adoption and large-scale propagation of efficient stoves to improve the health of rural women and to reduce the consumption of firewood and environmental pollution."

Jan 1, 2014

By J. R. Donald

Surface and interfacial phenomena play a significant role in refractory performance. For example, the wettability of the refractory material with slag, matte, and metal influences infiltration and interfacial reactions. Yet, very little fundamental information regarding the surface properties of refractory materials and slag is available. Thus, in the present work, the sessile drop technique incorporating a high temperature furnace equipped with X-ray fluorescope was employed to investigate the surface and interfacial phenomena of fayalite-type slags on solid alumina at 1200?C. The iron to silica (Fe/SiO,) ratios employed were 1.4 and 2.0, and the oxygen potentials used were log p02 =-11 and log p02=-9 atmospheres. The contact angle between the fayalite-type slags and the alumina were determined to be relatively low, at about 16.9 to 19.6 degrees under the experimental conditions. The surface tension of fayalite slag (Fe/SiO2=1.4) at an oxygen potential of log -11 was 0.298, which agreed with the work of previous researchers. The surface tension of the fayalite was observed to increase with time. The spinel FeAl2O4. was determined to be the product of the interfacial reaction, and 8.8 to 15.8 mass percent alumina was dissolved into the slag after 40 minutes.

Jan 1, 1996

By Christoph Pichler

A special desulphurization slag accrues during the processing of iron ore to steel, which is needed to generate high quality steel. Sulphur removing is done by different technologies, but the most common one is the generation of a high sulphur containing slag by sulphur affine elements. Currently, this desulphurization slag is partly recycled, however, huge amounts are still dumped. To utilize this desulphurization slag for future purposes, a recycling process must be established. Therefore, first characterization of this material started some years ago at the Chair of Nonferrous Metallurgy, Montanuniversität Leoben. Subsequent trials in lab scale size were performed, also some investigations for different treatment steps were evaluated, starting with a parameter study in a hot stage microscope at various gas-atmospheres. Finally, the developed recycling process concept was verified in pilot scale trials to confirm the new recycling technology. Due to the successful treatment process, also a patent was applied.

By F. Nava-Alonso, O. Alonso-González, A. Uribe-Salas, R. Pérez-Garibay

"Cyanidation is the most used method to recover gold and silver from their ores. In this process, other metals besides gold and silver may sometimes dissolve and interfere with the efficiency of extraction. Copper is one of those metals, reaching concentrations as high as 1000 mg/L in some cyanidation plants, making difficult the extraction and purification processes, and increasing the operating costs.This preliminary work was intended to study the feasibility of using amines to form a precipitate and to eliminate copper from a synthetic solution containing high copper and cyanide concentrations, as is the case of some cyanidation effluents. The solid formed is removed from the solution using conventional filtration techniques. Seven amines were evaluated at different pH values and amine additions. Up to 90% of copper present may be removed at the natural pH of the effluent (alkaline). The remaining copper would permit to recycle the solution back to the cyanidation process. IntroductionCopper is generally considered the most problematic metal in gold leaching due to the rapid formation of copper cyanide complexes when some readily-soluble minerals are processed (e.g., azurite, malaquite, cuprite, chalcocite and bornite). The copper solubilization as cuprous cyanide complexes leads to a significant economic penalty in terms of excessive cyanide consumption and high cost for cyanide elimination. When activated carbon is used to recover gold and silver, the copper-cyanide complexes decrease the efficiency of the process because of the competition of the cuprocyanides with the aurocyanide for the adsorptive sites on the activated carbon (Rees and Deventer, 1999).Several techniques have been developed to attempt to overcome the problems caused by the copper presence in cyanidation solutions, notably: acidification-volatilization-regeneration (AVR), ion exchange-electrolysis or solvent extraction-electrowinning (Lu et al., 2002). In this work the use of some amines is proposed to remove the copper-cyanide complexes by precipitation of a copper-cyanide-amine solid. The process was evaluated for different amine additions and pH values, using copper-cyanide synthetic solutions of composition similar to that presented by some cyanidation plants with high copper."

Jan 1, 2008

By Hiroshi Hashimoto

For the application of sodium carbonate slag treatment to product high purity copper on an industrial scale, the counter-flow batch process that reduces the amount of utilized slag is proposed from the viewpoint of the post-treatment of slag. Based on the distribution ratios of several impurities between the slag and molten copper determined previously, the effectiveness of this process is discussed using a mathematical model and confirmed experimentally. According to the model, the slag consumption to remove Sb to a required level in case of the counter-flow batch process with 3 reactors is calculated to be around 30 % of that in the case of an ordinary batch process, where pure sodium carbonate is used as a slag at every stage.

Jan 1, 2003

By J. R. Parga

A shortage of landfill space and growing environmental concerns in Mexico are renewing interest in the recyclability of scrap from automobiles. This work describes a pyroumetallurgical process for the recovery of metallic lead from waste lead paste. Argentopyrite concentrate is commingled with lead paste residue and smelted in a fuming process thereby transferring the precious metals into lead bullion. The process consists of smelting lead paste and argentopyrite, sodium carbonate, and metallic iron at smelting temperatures of about 1100 T. The reaction products are slag and molten lead bullion enriched with precious metals. A major feature of this process is the removal of precious metals from the bullion by means of zinc, whereby a silver-zinc intermetallic compound is formed and floats out of the lead. The recoveries of precious metals are about 98%.

Jan 1, 1996

By Hiroshi Hashimoto

For the application of sodium carbonate slag treatment to product high purity copper on an industrial scale, the counter-flow batch process that reduces the amount of utilized slag is proposed from the viewpoint of the post-treatment of slag. Based on the distribution ratios of several impurities between the slag and molten copper determined previously, the effectiveness of this process is discussed using a mathematical model and confirmed experimentally. According to the model, the slag consumption to remove Sb to a required level in case of the counter-flow batch process with 3 reactors is calculated to be around 30 % of that in the case of an ordinary batch process, where pure sodium carbonate is used as a slag at every stage.

Jan 1, 2003

By Muhlis Nezihi Saridede, Burak Birol

"The scraps of high quality steels generally contain expensive alloying elements such as chromium, vanadium, nickel, etc. These scraps are melted in an induction or an electric arc furnace and refined in ESR (Electroslag Remelting) purification process. A significant amount of alloying elements are lost during these processes. In order to avoid these losses, scraps can be utilized directly in ESR by skipping the melting step. In this study, 316L stainless steel scraps were refined in ESR with selected synthetic slags. The products were analyzed by optic emission spectrometry and the effects of slag compositions on the alloying element losses were examined. According to the analysis of the scrap and the products, generally chromium, nickel and manganese losses were encountered. It was determined that the alloying element losses has no connection with electrical conductivity. The slag containing CaF2, Al2O3, and FeO gives the optimum Cr and Ni losses.IntroductionElectroslag remelting (ESR), which is the consumable electrode refining process, finds a wide range of utilization for the production of high quality, low inclusion alloys. This process is based on melting a consumable electrode under a molten synthetic slag containing CaF2, Al2O3, CaO etc. The synthetic slag provides the chemical refining and insulation of molten metal from air which leads to a higher purity and an inclusion-free product. [ 1,2] A schematic diagram of ESR system is shown in Figure 1."

Jan 1, 2011

By V. M. Mukhin

Among the methods proposed for spent activated carbon regeneration, the most acceptable is, thermal reactivation, because in this case the existing equipment for manufacture of activated carbon can be adapted for this purpose. In order to conduct the process of thermal re-activation of spent activated carbon directly at gold mills, a full-scale drum-type furnace with external electric heating has been developed, i.e. EPV-300 model with a throughput rate of 50 to 120 kg/hour. Its use ensures restoration of the adsorption properties of carbon up to the level of fresh activated carbon with an insignificant (by 0.7%) decrease in strength and with a high (95% to 97%) yield of reactivated carbon. During the recent years, activated powder carbon has been extensively used in flotation processes for treating polymetallic ores at ore treating plants to improve recoveries of main metals (copper, lead, nickel, etc.). Especially large volumes of activated powder carbon are used at the Talnakh concentrator of the Norilsk Mining and Metallurgical Complex in Russia for absorption of residual flotation reagents from recycled water in order to ensure efficient selective separation of minerals with similar physical and chemical properties.

Jan 1, 2006

By Fu-Shen Zhang, Mengjun Chen, Jianxin Zhu

"A novel approach for foam glass preparation, namely vacuum-aided powder sintering technique, was preliminarily investigated in the present communication. The key point of which was to prepare foam glass at a negative pressure. Compared to normal powder sintering process, the new approach could benefit the foaming process by shorting the holding time, reducing the amount of foaming agent and especially decreasing relative density of the product. Optimum conditions were 750 °C, 1000 Pa, 5 min and 1 wt.% foaming agent, respectively.IntroductionFoam glass represents a highly valuable solution for thermal and acoustic insulation, since it possesses a generally higher mechanical, chemical and thermal stability than other foams'1'. The first industrial processing for foam glass production, the direct introduction of gases (""blowing"") into the special molten glass, can be dated back to the end of 1930s'2'. At present, almost all foam glasses is prepared by powder sintering technique instead of blowing,3 since it reduces the temperature by several hundred degrees. Moreover, as fine glass powders or similar powders can be used to substitute corresponding glasses by this technique, considerable attention has been focused on the production of foam glass by considering fully recycled glasses, coal fly ash, or other solid wastes as raw materials,4 especially CRT glasses'3' 5', on the point of environmental protection.In a previous report'6', when discussing the lead removal and recovery from CRT funnel glass by a pyrovacuum process, we found that foam glass could be prepared at a negative pressure. Therefore, in this communication, the similarities and differences between the powder sintering process for foam glass at normal and negative pressure was preliminarily discussed."

Jan 1, 2011

By Long Meng, Yaodong Yi, Kuiyuan Chen, Zhancheng Guo, Yu Li

Blast furnace slag is the main by-product discharged in the iron and steel industry and contains considerable waste heat at dischargeing temperature between 1450 and 1550 °C. To fully utilize waste heat and slag, this study directly converted high temperature liquid Ti-bearing blast furnace slag into glass-ceramics via the “Petrurgic” method. Samples at different crystallization temperature were prepared and its influence on crystal phases, pore structure, and compressive strength were investigated via SEM, XRD techniques, and compressive strength measurements. Results showed that all glass-ceramic samples contained main crystals of perovskite, diopside and gehlenite and had a qualified mechanical performance with compressive strength above 100 Mpa, which meets the requirement of Chinese national standard for natural granite stone. With increasing crystallization temperature, pore size decreased, while the size of the perovskite phase firstly decreased and then increased with decreasing crystallization temperature. Samples had an optimum crystallization temperature of 1215 °C, maximum grain size and a densified structure with minimal pore defect.

Mar 1, 2018

Al2O3,-WC Composite powder for cutting tools was synthesized by self-propagating high-temperature synthesis using A1 powder as a reducing agent. WC, W2C and Al2O3 were concurrently formed in WO3Al-C system. It was found that the complete reaction was achieved with excessive addition of carbon and appropriate processing parameters such as degree of dilution, particle size of aluminum, compaction pressures of green pellets and carbon source. The final product which was leached by 50% HN03+HF diluted solution was consisted of Al2O3-55wt% WC having 2-3um of mean particle size.

Jan 1, 1999

By R. J. Kuczynski

The U.S. Bureau of Mines operated a 2,000-9 (4.4-lb) batch process development unit for recovering platinum-group metals (PGM) from automobile catalysts. Virgin monolith, used pellet and used monolith catalyst samples were tested. Leaching twice with 1-pct sodium cyanide (NaCN) solution at 160' C for 1 h in a pressure vessel dissolved over 95 pct of the PGM from virgin catalysts and over 90 pct from used pellet catalysts. Over 85 pct of the PGM was dissolved from used monolith catalysts when a third leaching step was added. PGM concentrates as metallic powder containing over 99.8 pct of the dissolved PGM and analyzing greater than 70 pct PGM were recovered by heating the pregnant leach solutions from virgin catalysts to 250' C and used catalyst to 275" C for 1 h. The solution after heating contained primarily sodium carbonate from cyanide decomposition and less than 0.2 ppm total cyanide.

Jan 1, 1993

By Afshin Sadri

Acousto Ultrasonic-Echo (AU-E) is a technique developed to provide accurate measurements of the refractory lining wear in operating smelters based on the principles of stress wave propagation. The objective of the system is to provide feedback for the continuous optimization of the overall smelter operation. In some cases, the AU-E refractory lining measurements have allowed clients to extend their smelter campaigns and operate safely for several years beyond their planned reline schedule. In other cases, AU-E results inform clients of serious issues within their furnace allowing them to shut down their smelters ahead of predicted failures and possible disasters. This paper presents the results of several smelter AU-E inspections of the hearth and sidewall. These case studies demonstrate how the AU-E results were used to positively affect the smelter operation.