Search Documents

By Wei Yu, Tiejun Chun, Jian Pan, Deqing Zhu

In this paper, the technology of producing fluxed pellets by using hydrated lime as binder instead of bentonite was carried out. Green balls with 0.8% bentonite and others with 2% hydrated lime were obtained under the same conditions of 1.5% coke, 1.45 basicity and balling at 8.5% moisture for 13 min in disc pelletizer. The properties of two types green balls were as follows: drop numbers of 4.8 to 5.0 times/0.5m, compressive strength of 19.7 to 24.2 N/pellet and thermal shock temperature of 280 to 385?, respectively. Comparing with bentonite as binder, the compressive strength of fired pellets with hydrated lime is elevated by 13.8% and climbs up to 3113 N/pellet under the following conditions: preheating at 1050? for 10 min and firing at 1300? for 15 min. The hydrated lime also improves the metallurgical performance of fired pellets. The reduction index was enhanced from 68.6% to 70.6%, RDI+3.15 increased from 90.1% to 98.8% and reduction swelling index dropped from 22.4% to 7.4%, respectively. Therefore, hydrated lime can not only replace bentonite as binder to enhance the firing behaviors of green balls, but also effectively improve the metallurgical performance of fluxed pellets which can be used as high quality feed for blast furnace.

Jan 1, 2011

By Shadia Ikhmayies

Thermo-Calc software was used to investigate the phase diagram of the calcium silicon (Ca–Si) system for the range of Si mass percent 0–100, and temperature range T = 200–1800 K. The melting points of Ca and Si deduced from the phase diagram are very close to the values obtained experimentally. Three stable intermediate solid phases were found, which are Ca2Si, CaSi, and CaSi2, where the first one appeared in the Ca rich side of the phase diagram, and the third one in the Si rich side. In addition, three eutectic points were found at Si mass percents of 3.95, 33.00, 62, and temperatures T = 1048.7, 1519.14, 1308.5 K respectively. Atomic Si (Diamond structure) is found mixed with CaSi2 intermediate phase for temperatures less than 1305 K, and mixed with a liquid CaSi for higher temperatures. These results are important for thermodynamic and metallurgic studies of these intermediate phases.

Mar 1, 2018

By Jun Sugiyama, Hiroyuki Sano, Toshiharu Fujisawa, Hideki Takeuchi, Chikabiuni Yamauchi

"The solid .state electrotransport (SSE) is one of the most promising methods for the elimination of gaseous impurities from chemically active metals, such as rare earth metals. . In the present work, the SSE process was applied for the oxygen removal from praseodymium. The SSE factors, such as effective valence, were measured under the various temperatures, electric field intensities and initial oxygen contents, and the effects of those conditions on the SSE process were discussed. Furthermore, the solubility of oxygen in .solid praseodyillium was also measured·, by using the SSE method and metal-oxide equilibrium method.IntroductionWhen a direct current is passed through a solid alloy, not only electrons but also solute atoms are transported as charge carriers toward the anode or cathode. This phenomenon is referred to as an electrotransport or electromigration. The solid state electrotransport (SSE) is the application technique, based on this principle, to the pUrification of the solid metallic materials.Rare earth metals are used for various functional materials, such as magnetic, optical or electronic materials, therefore their high purity metals are required [l ,2]. However, rare earth metals are chemically active and have a strong affinity with gaseous elements (e.g. oxygen, nitrogen, hydrogen and carbon). In many cases, eliminating operations of gaseous elements have not been always made commercially, because these impurity elements could not be eliminated by usual treatments applied to the purification of ·common metals. As an alternative method, authors have proposed the· application of the SSE process to the elimination of gaseous impurities from rare earth metals. Investigations have been carried out on the yttrium-oxygen and neodymium-oxygen systems and the results were already reported[3,4]."

Jan 1, 2000

By Björn Saxen

Outotec atmospheric Direct Leaching has so far been implemented for zinc production capacities of around 100,000 t/a. Lately, there has been growing interest for small scale direct leaching plants, producing circa 30,000 t/a of Zn. Such small leaching plants can provide extra front-end capacity in existing roaster-based plants and enable treatment of feed materials not suitable for roasting. In small scale plants the proven OKTOP® 9000 Direct Leaching reactors are not readily applicable, due the large size. For smaller installations a modular approach is proposed providing multiple advantages, such as reducing the construction time and amount of the site work required causing less disturbance to regular plant operation with reduced cost. In this paper, we present advantages that can be achieved by using modular OKTOP®C reactors and discuss also process design when connecting a small scale direct leaching process to an existing zinc plant. Also benefits of direct leaching expansion are presented.

By Fuqiang Zheng, Shuai Wang, Ting Duan, Yufeng Guo, Tao Jiang, Andrew Yakovlevich Travyanov

Organic compound binder can effectively enhance the strength of green pellet and reduce the addition amount of binder during pelletizing. However, compared with traditional bentonite binder pellet, the compressive strength of the preheated and roasted pellets significantly declined. It is of significance to resolve this problem for the application of organic compound binder. In this paper, magnetite concentrate was used as raw material, carboxymethyl cellulose (CMC)- bentonite compound was used as binder, characteristics of preheated and roasted pellets and the effects of additives on that were systematically studied, The results show that sodium acetate can effectively improve the characteristics of the finished compound binder pellets. The compressive strength of the preheated and roasted pellets were increased by 52/N·p-1 and 342/N·p-1 respectively when the addition amount of sodium acetate is 2.2%wt of compound binder. Moreover, sodium acetate has no adverse effect on pelletizing process and drying characteristics of green balls.

Jan 1, 2015

By Yeole Shivraj Narayan, Nunna Nagabhushana Ramesh, Banoth Balu Naik, Alluru Ramya

MicroEDM process is mainly used for producing miniaturized features like microholes on different types of materials that are hard to cut and difficult to machine. One typical application of microEDM process is microhole drilling operation. Choice and utilization of optimum pulse parameters is of utmost importance for achieving superior surface quality and higher machining rates. However, the process is characterized by low machining rates and considerable overcut as compared to conventional EDM drilling. An attempt is made to investigate the effect of pulse parameters on maraging steel 300 alloy during micro EDM drilling. Parameters like pulse on time, pulse off time, voltage and current are explored through 09 experiments replicated thrice using Taguchi method. Machining characteristics like material removal rate and overcut are studied while drilling micro holes of 500 µm diameter using brass electrode. Evaluation of microhardness after microdrilling is also performed. It is found that puls on time and current influenced the machining characteristics. Minimal change is observed int he microhardness of the alloy after microdrilling.

Mar 1, 2018

By Chen Qizhou, Wang Yun, Zhu Rong

SiO2 and Al2O3 in the metallurgical slag of nickel laterite ore have great recycling values. In this work, Si and Al were extracted from the slag in NaOH based molten salts through alkali roasting and water leaching process for preparing zeolite materials. The extraction ratio of SiO2 increases with increased temperature and appropriately prolonged time, and more than 80% SiO2 can be recycled from the slag after roasting at 550°C. Si and Al from the slag are in the filtered liquor for producing zeolite materials, while Mg, Ca, Fe and other impurities remain in the leached residues. Adding Na2CO3 into the alkalin-slag roasting process can reduce the amount of pure NaOH used with minor decrease in extraction ratio of SiO2, while make better separation of Ca to avoid it getting into the filtered liquor. Adding Al2O3 into the alkalin roasting process can replace part of more expensive NaAlO2 addition that is required for preparing zeotite material, which may bring out a minor decrease in extraction ratio of SiO2 due to formation of NaAlSiO4 in the filtered residues. Quality X zeolite and 4A zeolite materials can be made from the starting liquor containing Si and Al recycled from the laterite nickel slag through alkali roasting and water leaching process.

Mar 1, 2018

By Richard M. RusselI, Jerry Sweeney

"The disposal of Aluminum slag wastes continues to challenge an otherwise environmentally beneficial and highly desirable industry - Aluminum Recycling. Slag wastes contain soluble salts that can be reused in aluminum smelting. Reclaiming salt is a logical first step in eliminating slag waste.Reclaiming salt flux has been conducted on a limited basis in the United States for reasons of economy. Practical methods and rising landfill tipping fees will increase the number of plants which opt to recover salts from slag wastes.The authors share their experiences in the design, operation and startup of a commercial scale flux reclamation plant operated by Tennessee Aluminum Processors at Mt. Pleasant Tennessee. This paper identifies three elements that allow practical operations:• Minimizing Evaporator Heat Duty• Simplifying Evaporator Operations• Potassium Chloride Fortification of the Recycled Salt"

Jan 1, 2000

By Sarel Johannes Francois Gates, Ida Kero, Yan Ma, Gabriella Tranell

During the tapping and casting of manganese ferroalloys, fumes are generated and released to the working environment. The fumes are mostly composed of metallic oxides generated due to reaction between high temperature molten metal and ambient oxygen in the air. From an environment perspective, it is important to limit these emissions. However, to do so, it is important to understand fuming mechanisms and kinetics as well as fume compositions, i.e. element behavior during the oxidation process of liquid manganese ferroalloys. Silicomanganese alloys are composed of aminimum of 65 wt% Mn and 17 wt% Si, 2 wt% C as well as minor and trace elements. These elements include Fe, Mg, Al and other elements originating from ores and reductants. Trace elements behavior in fume from liquid silicomanganese generated under an impinging air jet in the temperature range of 1450–1700 °C has been investigated in this work. The thermodynamic and kinetic conditions governing the generation mechanisms are discussed.

Mar 1, 2017

By C. J. Newman

In January 1999, a redesign of the Kennecott Flash Converting furnace settler was initiated to enhance furnace integrity and extend furnace life. This furnace uses Kennecott-Outokumpu Flash Converting technology to produce copper directly from copper matte. A detailed assessment was made of all technology available around the world before making a decision on the design features to be incorporated in the new design. The new design includes the following: redesign of all sidewall cooling elements to include the latest cooling element technology; redesign of the furnace hearth to include a stadium hearth at the reaction shaft end of the furnace; redesign of the furnace hearth to include a stepped hearth design adjacent to the furnace sidewalls; addition of flat settler roof cooling elements .around the reaction shaft; replacement of reaction shaft transition elements with an improved design and improvements to the furnace cooling element monitoring systems. The Flash Converting furnace was shut down on a planned basis in July 2001 to implement these improvements after 29 months of operation, converting more than 1,000,000 tonnes of matte. During the 30 day shut down, the improvements were successfully completed, with furnace start up in August 2001

Jan 1, 2002

By E. V. Verhoef

The proposed EU directive on the restriction of the use of certain hazardous substances in electrical and electronic equipment promotes the substitution of lead in consumer electronics to reduce emissions from lead in the end of life phase. In this paper, the consequences of substituting lead in solders is assessed using the Eco-lndicator-99 method for the examples. The base metal production system is considered as an interconnected network modeled dynamically in Simulink 4 and Matlab 6 (Mathworks Inc 2000), where the recovery and production of metal components of the assessed product partially overlap. This approach requires global modeling of metal production processes and mass balances and resulting allocation choices. It also reveals the susceptibility of LeA scores to different choices in the modeling and data availability and uncertainty. Besides the comparison between lead-free and lead-containing solders, other side effects are revealed. Lead is carrier material for the recycling and production of many co-elements in the interconnected production and recovery system. Substitution may have adverse effects such as temporary shortages of other connected metals that are often not considered in normal LeA assessments, thus leading to erroneous results. The suggested approach provides directions for including these external effects and for further assessment of the environmental effects of substituting lead. This paper shows that in order to assess the environmental aspects of metallurgy, dynamic modeling of the total system is required based on the fundamental thermodynamics in each metallurgical reactor, the basis of this dynamic model. With this the true environmental impact of metallurgy can be explained. In the case of lead free solder, it is shown that the mining of substitutes has a very much larger impact.

Jan 1, 2003

By E. V. Verhoej

The proposed EU directive on the restriction of the use of certain hazardous substances in electrical and electronic equipment promotes the substitution of lead in consumer electronics to reduce emissions from lead in the end of life phase. In this paper, the consequences of substituting lead in solders is assessed using the Eco-Indicator-99 method for the examples. The base metal production system is considered as an interconnected network modeled dynamically in Simulink 4 and Matlab 6 (Mathworks Inc 2000), where the recovery and production of metal components of the assessed product partially overlap. This approach requires global modeling of metal production processes and mass balances and resulting allocation choices. It also reveals the susceptibility of LCA scores to different choices in the modeling and data availability and uncertainty. Besides the comparison between lead-free and lead-containing solders, other side effects are revealed. Lead is carrier material for the recycling and production of many co-elements in the interconnected production and recovery system. Substitution may have adverse effects such as temporary shortages of other connected metals that are often not considered in normal LCA assessments, thus leading to erroneous results. The suggested approach provides directions for including these extemal effects and for further assessment of the environmental effects of substituting lead. This paper shows that in order to assess the environmental aspects of metallurgy, dynamic modeling of the total system is required based on the fundamental thermodynamics in each metallurgical reactor, the basis of this dynamic model. With this the true environmental impact of metallurgy can be explained. In the case of lead free solder, it is shown that the mining of substitutes has a very much larger impact.

Jan 1, 2003

By G. Richards

The Trail smelter of Teck Metals Ltd. produces about 90,000 tonnes of lead per year through two stages of refining following KIVCETTM smelting. Bullion from the KIVCET furnace is first treated in a pyro-refining plant in preparation for Betts electrorefining which makes 99.99% pure lead. Pyro-refining consists of number of integrated unit operations to remove primarily copper, arsenic, antimony and tin. The operation of this plant to meet the specifications for electrorefining requires attention to bullion management and selective use of reagents. The processes used for pyro-refining are reviewed in terms of chemistry and control.

By Claassen J. O.

The Zinc Corporation of South Africa Ltd. (Zincor) operates an integrated roast ? leach ? electrowinning circuit. The efficient removal and control of iron forms an integral part of the process. Zincor developed its own iron removal process (Zincor Process), which was recently shown to be unique with some similarities to the para-goethite iron removal process. Newly developed operating parameters for iron removal are in the process of being implemented. These include a change in the pH-profile and operating temperature, the recycling of seed material and the utilisation of an alternative neutralising agent to aid iron removal. Some of these actions, together with the implementation of a pre-neutralisation step, new filtration equipment and control systems in Zincor?s Residue Treatment Plant have significantly reduced zinc losses associated with iron in calcine and the iron residue produced. This enabled Zincor to take a step closer to world-class zinc recovery levels of around 96% for a similar type of operation.

Jan 1, 2003

By Wangzhi Zhou, Jian Xu, Jing Zhang, Xuecheng Gong, Mingsheng He, Guohua Xie

Graphite, which has a unique stack structure that enables a small friction coefficient, is used as one kind of the best hearth rolls to support and convey silicon steel strip in continuous annealing furnace. However, the buildup formation in/on the surface of carbon sleeve has always been a worldwide difficulty in the silicon steel industry. Based on the analysis of the microstructure, topography and composition of the buildups, combined with simulation experiments, the mechanism of forming buildups is discussed. The results show that buildups experience the process from nucleating to growing-up, and buildups are formed by nano liquid phase sintering (NLPS). Meanwhile, some countermeasures to reduce or prevent the formation of the buildups are proposed.

Mar 1, 2018

By Kimberly Conner-Mills

Due to increasingly stringent worldwide environmental regulations for gaseous, aqueous and solid waste emissions, conventional smelting technology cannot effectively process arsenic containing materials. Many globally significant copper properties have copper sulfide mineralogy that has a high arsenic content present as enargite with significant contained precious metals. As global copper, silver and gold demand increases while significant world resources decrease, treatment of sulfide orebodies with enargite is becoming increasingly important. Methods to selectively dissolve and fix arsenic, leaving behind clean copper and precious metals-bearing concentrates could effectively treat these ores.

By Senlin Cui, In-ho Jung

Significant amount of commercial aircrafts will be retired in 2020, and the recycling of Al components in such aircrafts becomes an important issue in aerospace and Al industry. Recycling of Al from obsoleted Al products can effectively reduce the energy consumption and CO2 emission which is more economical and ecofriendly. In the present study, thermodynamic analysis for the various recycling technologies of Al alloys were performed based on the comprehensive and accurate thermodynamic database. The recycling technologies reviewed in this work include the vaporization process to reduce Zn, precipitation process to reduce Fe, Mn, Si, Ti, Zr, flux treatment for Al 2O3 and MgO, etc. Several key issues and limitation of the recycling of the aircraft Al were discussed. The recycling technologies discussed can also be utilized to recycle other Al alloys for common usage. All the thermodynamic calculations were performed using the FactSage FTlite database.

Mar 1, 2017

By Dale T. Peters

Conductivity, both electrical and thermal, are attributes accounting for about 70% of the applications of copper and its alloys. This paper presents results of on-going research into two new applications that depend on copper's excellent conductivity. The Copper Development Association (CDA), together with materials and motor company partners, is working toward a solution to the key problem preventing pressure die casting copper for the conductor bar/end ring structure of the induction motor rotor, i.e., lack of a durable high-temperature mold material. Work is showing that a combination of high- temperature materials and elevated temperature processing gives much improved mold life compared to die steels. Substitution of copper for aluminum in the rotor can result in a 20% decrease in electrical losses in motors consuming 35% of electrical power generated in the U.S. The second development uses the excellent thermal conductivity of several high-strength high-copper alloys to simultaneously improve productivity and part quality in the injection molding of plastic parts.

Jan 1, 1999

By J. Huisman

With the introduction of ever-stricter environmental operating guidelines, capital expenditure restrictions and operational budget cutbacks, the biological method of SO2 removal becomes more and more attractive. Biological treatment of dilute flue gases is a more cost effective technology in comparison to conventional sodium hydroxide scrubbing. Although the investment costs for sodium hydroxide scrubbing is lower, the operational costs are significantly higher. In addition, the end product of the biological installation is sulfur instead of sodium sulfate; and no further wastewater treatment of the bleed from the biological installation is required since heavy metals are removed simultaneously. Another option for the treatment of SO2 containing gas at a sulfuric acid plant is the production of extra sulfuric acid of the discharged SO2 by applying an additional converter. Comparing biological treatment with this option shows much lower investment costs for the biological installation. Sulfur is produced which can be converted to sulfuric acid, so the bio-route will be more cost-effective than an additional converter. In principle, the biotechnological gas cleaning system is an integration of an absorber with a wastewater treatment facility. In the absorber, the SO2 containing gas is brought into contact with the washing water. The effluent absorber liquid contains a mixture of sulfite and sulfate that is converted into elemental sulfur. This conversion takes place in an integrated system; first, the sulfite/sulfate mixture is converted anaerobically into sulfide; secondly, the sulfide is converted aerobically into elemental sulfur. Subsequently the sulfur is separated and the water is returned to the absorber. Due to the buffer capacity of the washing water, removal efficiencies over 98% are possible. In addition to SO2 removal, it is possible to convert for example other bleeds streams such as scrubber acid or weak acid to sulfur in the same SO2 installation. Recent evaluations concluded that biological desulphurization of flue gases is not only economically attractive in comparison to convention sodium hydroxide scrubbing but also in comparison to gypsum producing systems and even seawater scrubbers. This paper describes the technological and economical viability of biological flue gas desulphurization.

Jan 1, 2005

By Chai Li-yuan

Anodizing behaviors of magnesium alloys AZ31 at constant applied current, based on the electrolyte solution free of chromate or fluoride, were investigated. The anodizing process was influenced by constituents of electrolyte greatly. Therein, the oxylate salts, which led to the occurrence of the two totally different processes, played a determinant role in anodizing. They were stable and sparking process respectively. The morphology of anodizing film was observed by SEM and the structure of film was analyzed by XRD. During the stable process, a brown thin film was formed, however the sparking process led to the formation of white hard thick film. The functions of some kinds of additives, such as ammonia, glyceryl alcohol and PVP etc were also studied. Some of them had great effect on surface morphology of anodic film and some of them affected stability of anodizing process significantly.

Jan 1, 2006