Search Documents

By J. D. McCain

Magma's San Manuel smelter has adopted new operating techniques resulting in 21% increased productivity and 87% reduction in lost time accidents. Reverberatory furnaces were converted to coal firing from expensive natural gas and fuel oil. Slag and matte flow problems and safety were improved by implementing hydraulic slag stopping and matte tapping machines. Coordination of furnaces, converters and acid plant was improved by using a computer-aided converter controller/scheduler function. Manual mudding of converter lips after each collar pull was replaced with a gunning system for coating the mouth castings. One converter punch car was automated using robotic technology. An automatic anode take-off was installed with fewer moving parts and a mechanism for ear twisting one cell contact. Anode copper refining was improved by replacing propane/hydrogen mixtures with high pressure/velocity natural gas tuyeres. Improved converter scheduling increased acid plant production 43% with more autothermal operation time. Six dedicated computers/microprocessors are utilized for automation, data acquisition, process monitoring and on-line air quality information for the Supplementary Control System.

Jan 1, 1983

By Liu Wei-feng

In this paper, the practice of separating precious metals from base metals in gold-antimony alloy by selective chlorination leaching under controlling potential in China has been introduced in detail. The precious metals and the base metals can be separated completely when the complex gold-antimony alloy is treated by this process. The impurity metals were removed effectively since the leaching efficiencies of copper, nickel and antimony are over 99%, with direct recovery of gold being 99.83% that is about 20% higher than that of the original process and silver, antimony, copper and nickel are also recovered effectively. The gold grade of the resulting crude gold powder can reach to 94%.The new process has been applied in the treatment of gold-antimony alloy for two years, and many former procedures have been cancelled, such as electrolysis, Anode slime leaching by nitric acid, smelting in crucible and blowing in muffle. The new process is more shorten, lower cost and friendly to the circumstance comparing to the original process.

Jan 1, 2008

By Jakub Kaczorowski

In the production of Mn-alloys, the Boudouard reaction significantly influences the mass and energy balance. The endothermic nature of this reaction requires more energy for the process, while the direct consumption of carbon is reflected in the greater demand for carbonaceous raw materials. Therefore, it is desirable to eliminate or suppress the reaction. The kinetics of the Boudouard reaction are a function of many factors, of which coke properties and the conditions around the particles (i.e. temperature, gas composition) seem to be the most important. In the present study properties of selected single source and commercial metallurgical cokes are compared with reactivity results. The single source cokes represent a single coal that has been carbonized in a laboratory scale furnace. The commercial cokes are products of carbonization of coal blends under industrial conditions. The coke properties include proximate, ultimate and ash analysis. Also, coke petrography with carbon forms is included. The reactivity tests were performed on different particle sizes at various temperatures, gas compositions and gas flow rates. The experimental parameters were chosen to simulate the conditions in an industrial furnace. The results show that highly graphitized structure of cokes, minimal surface area and a low concentration of ash retard the reactivity. Of the other factors, the temperature and the gas composition have the greatest impact on the reactivity.

Jan 1, 2006

By F. H. (Sam) Froes, C. Suryanarayana, K. C. Russell, C. M. Ward-Close

"Far from equilibrium synthesis allows development of novel crystal structures and microstructures, leading to achievement of enhanced physical and mechanical properties. A number of ""far from equilibrium"" techniques are reviewed with emphasis on the amount of departure from equilibrium. The ability of two such techniques, mechanical alloying (MAl, and physical vapor deposition (PVD) to develop novel structures are discussed in detail. For the MA process emphasis is placed on intermetallic compound compositions. Solubility extension, beyond rapid solidification (RS) levels, is found in terminal compositions but not for the intermetallics. Nanostructure-sized grains (< 100nm) form which can be retained after ""low temperature"" compaction. On continued milling in many cases the nanometer-sized grains transform to an amorphous structure. Ordering is destroyed by MA, except in those intermetallics with large negative enthalpies of formation. For the PVD process, a review of application to terminal light alloy compositions is presented. This includes a new high-temperature aluminum alloy, layered materials with nanometer spacing, corrosion-resistant magnesium alloys and low-density titanium compositions. IntroductionTo enhance the mechanical property combinations of advanced structural materials innovations in process/synthesis are required [1-6]. In this paper the capability of various ""far from equilibrium"" synthesis techniques [7,8] to produce novel constitutional and microstructural effects, and hence potentially enhanced physical and mechanical properties, in advanced materials is presented. The application of two such methods, mechanical alloying (MA) and physical vapor deposition (PVD) is discussed in detail. For the MA process emphasis is on intermetallic compositions with consideration given to solid solubility extension, microstructural refinement, amorphization, and formation of intermetallic compounds. For the PVD process application to terminal light alloy compositions is discussed."

Jan 1, 1994

By Yuanbo Zhang, Zhixiong You, Zijian Su, Bingbing Liu, Guanghui Li, Guang Yang, Tao Jiang

Sodium stannate is widely used in the electroplating and tin alloy industry. But the traditional processes for sodium stannate production are characterized by long flowsheet, high production cost and strict requirement for the equipments, etc. In this study, a novel process for sodium stannate preparation from cassiterite concentrate and sodium carbonate via roasting in CO/CO2 mixed gas then followed by leaching was developed. The effects of roasting parameters on the Sn leaching efficiency were conducted. A Sn leaching efficiency of 77.2% was obtained under the optimal conditions. Sodium stannate (Na2SnO3·3H2O) with a purity of 95.8% was produced by the new process, which is better than that specified for the industrial first-grade product.

Jan 1, 2014

By Xin Li, Hai-Xing Fang, Bing Xie, Hong-Yi Li

Chromium-containing vanadium slag (V-Cr slag) was obtained by an industrial smelting process of Hongge Ore, which is valuable vanadium-titanium magnetite to extract V and Cr in China. Sodium roasting thermodynamics of V-Cr slag in presence of oxygen were calculated to evaluate the reactivity of chemical compounds. Results showed that the oxidation of FeV2O4 was intensified in presence of Na2CO3 while the oxidation tendency of FeCr2O4 was far lower than that of FeV2O4. It was probably that reactions of impurities including Al2O3, SiO2 and Fe2O3 with Na2CO3 happened and the products can promote the oxidation of vanadium or chromium compounds in lower valence. Based on thermodynamic analysis, a two-step selective extraction process of vanadium and chromium was proposed. Extraction rate of vanadium was 88.6% while 7.0% for chromium in the first extraction step; extraction rate of 90.7% and 95.4% for vanadium and chromium, respectively, were obtained in the second step.

Jan 1, 2014

By Roderick Guthrie

Gas injection into liquid steel baths is widely practiced, ever since the early days of Bessemer’s pneumatic steelmaking process. What has not been fully appreciated is the critical role of bubble sizes for delivering higher quality commercial steels than is presently possible. This was first proposed by Prof P. Hayes and his research group. Using a full-scale water model of a typical 4-strand Ladle-Tundish-Mold system, we demonstrate the potential advantages of modifying a typical ladle shroud, to generate microbubbles within the water flowing into the tundish. This is possible by taking advantage of high shear rates and turbulence kinetic energy available in that region. These microbubbles enhanced the removal of “micro-inclusions” (hollow glass microspheres) in the 5–50 micron size range, to the upper surface of the tundish. There, they were absorbed into an overlaying “slag” phase. Accompanying CFD studies confirmed that no microbubbles in the size range generated (500–900 μm), pass through the submerged entry nozzles into the moulds.

By Baozhong Zhao

Laboratory experiments have been conducted on the removal of As, Sb and Bi from molten copper by SF 6 injection. The results showed that the impurities can be removed by SF6 injection in the? sequence of Sb >As >,Bi and the rate of Bi removal is affected significantly by the concentration levels of As and Sb in the copper melt. Analysis of the experimental data indicates that the impurity removal process is under chemical reaction control rather than by mass transfer of impurity through the molten copper phase. On the basis of experimental results, a kinetic model was developed and the order of chemical reaction and the volumetric chemical reaction rate coefficients of impurity removal were determined.

Jan 1, 1996

By Andrea R. Kim, Ramana G. Reddy

Electrodeposition of cobalt from cobalt chloride using the urea and the choline chloride ionic liquid (2:1 molar ratio) was studied to search the optimized parameters for the higher current efficiency. The cyclic voltammetry was tested with 0.2 MCoCl2 using various scan rates to determine the reduction potential in Urea/ChCl at 323 K. Based on the data from cyclic voltammetry test, the transfer coefficient and the diffusion coefficient were calculated as 0.22 and 3.38 × 10−6 cm2/s, respectively. The parameters for electrodeposition of cobalt were various temperatures (323 –383 K), applied potentials (2.4 –3.3 V), and concentration of CoCl2 (0.2–0.5 mol/L). Current efficiency and energy consumption were calculated to investigate the optimal condition for the electrodeposition of cobalt. The highest current efficiency (95%) was obtained under the temperature 323 K, the applied voltage 2.7 V, and concentration 0.5 mol/L of CoCl2. Scanning electron microscope (SEM) and X-ray diffraction (XRD) were used for the characterization of cobalt deposits.

Mar 1, 2017

By Ruirui Wei, Mingrui Yang, Xuewei Lv

Calcium ferrite, as the main bonding phase in the sintering process, greatly influences the property of sintered ore. Ultrasonic vibration has been widely applied to the treatment of metals to improve the properties of metals. In this work, ultrasonic vibration was introduced into the calcium ferrite and numerical simulation was carried out by solving the Rayleigh-Plesset equation to investigate the influence of ultrasonic conditions, including frequency, power and initial radii of cavitation bubbles on the cavitation bubbling behavior in calcium ferrite melt. The results indicated that lower ultrasonic frequency, higher power, and an appropriate initial radius of bubble promotes ultrasonic cavitation.

Mar 1, 2018

By Yuanbo Zhang, Zhixiong You, Daoxian Duan, Guanghui Li, Tao Jiang, Xiaohui Fan

"Presently, high-grade manganese oxide ores are usually utilized by a coal-based reduction roasting process. However, there were some obvious drawbacks, including serious environmental pollution, high energy consumption, etc. The reduction temperature is relatively high (850-900 °C). In this study, a kind of biomass, pine black charcoal, was used as a reductant to reduce low-grade manganese oxide ores. Under the optimal conditions of reduction temperature of 600~650 °C, roasting time of 30~45 min and ratio of ore to reductant 5:1, the leaching efficiency of manganese reached more than 98%. Compared with the traditional coal-based reduction process, the reduction temperature is reduced by 250-300 °C.IntroductionManganese plays a very important strategic role in the national economy, and it is widely used not only in the metallurgical industry, but also in the light industry, chemical industry, medicine, agriculture, etc [1]. The average grade of manganese ores in China is evenly about 21%, which belongs to typical low-grade manganese ores [2]. Therefore, large quantity of high-grade manganese ores is required to import in order to meet the rapid development of Chinese manganese industry. As reported, the conventional treatment of reduction roasting has been widely applied for processing manganese oxide ores, in which coals or reducing gases (CO, H2 or CHi) were usually used as reducers [3]. However, there were some insuperable problems, such as high energy consumption, poor operating conditions, serious environmental pollution, etc [ 4-9]."

Jan 1, 2013

By A. Navarra

Peirce-Smith converting (PSC) is applied for roughly 50% of primary nickel and 70% of primary copper production. PSC cycles produce batches of ironfree sulfide matte (or blister copper, in the case of copper smelters), that are subject to further processing. However, the number of cycles that can be performed simultaneously is limited by the offgas handling system. Moreover, PSC suffers from variation in the yield and duration of the cycles. This variation is managed by conventional smelter designs, in which the upstream smelting capacity exceeds the nominal converting capacity; PSC is thus a major bottleneck in conventional nickel and copper smelters. Stabilization and standardization of PSC operations can therefore increase smelter throughput. The current paper presents a discrete event simulation (DES) framework to assist in smelter debottlenecking. It features random number generation to represent cycle variability, and time-adaptive finite differences to represent thermochemical complexity. Preliminary computations are presented.

By Dengfu Chen, Mujun Long, Youguang Ma, Xin Xie, Xing Zhang, Leilei Zhang

"Processing parameters of a submerged entry nozzle (SEN) affect significantly on the patterns of fluid flow and temperature distribution in beam blank continuous casting mold with double SEN s. Effect of the geometry structure and immersion depth of double SEN s on the fluid flow in beam blank continuous casting mold was studied by water modeling. Results showed that, the optimal nozzle inner diameter was 40mm, and immersion depth was 70-90mm. The mold surface fluctuation, slag distribution, impact depth and removing rate of inclusion particles were discussed under different processing parameters of double SENs. As the results indicated, slag distribution was more non-homogeneous with a higher casting speed. The results provided basic data for the design and optimization of SENs used in beam blank continuous casting mold.IntroductionNear-net-shape casting has the distinct advantages of less rolling procedures, higher metal recovery and lower energy cost. Therefore, in the recent decades, one of the recent trends in the steel making process is moving toward near net shape casting. in which beam blank casting is a typical technology. The schematic section of beam blank is shown in Fig 1."

Jan 1, 2014

By F. -Z. Ji

Carbon injection into metallurgical slag is important in electric arc furnace (EAF) steelmaking for foamy slag practices and in nonferrous slag cleaning operations. The current publication presents kinetic data for coal injection into EAF slag to understand the interaction between injected carbon and metallurgical slag. Coal particles were injected into EAF slag and the kinetics were followed by gas and slag analysis. The results were analyzed, in terms of fundamental rate equations for each possible reaction step, as a function of temperature and slag composition.

Jan 1, 2003

By Kuniaki Murase, Tetsuji Hirato, Koji Nitta, Yasuhiro Awakura

"The redox behavior of copper species in an ""ammonium imide"" room temperature molten salt was examined in order to clarify the applicability of the salt to the electroplating media of various metals. Trimethyl-n-hexylammonium bis(trifluoromethanesulfonyl)- amide (TMHA-Tf2N), having an electrochemical window of 5.6 V (50 °C), and corresponding copper(II) salt were synthesized. In TMHA-Tf2N media monovalent copper ion, Cu(I), was stable and Cu metal was oxidized, or corroded, in the presence of Cu(II) species. Cathodic electrodeposition of copper metal and anodic dissolution of it were, thus, one-electron reaction and their current efficiencies were almost 100%.IntroductionElectrodeposition of metals from aqueous solutions is an important soft process for manufacturing thin-film materials, surface finishing, and extractive metallurgy. However, the electrodeposition of base metals, such as zinc, chromium, and nickel, from aqueous media inevitably accompanies hydrogen evolution, which lowers the cathodic current efficiency of metal deposition. Since the electrodeposition of aluminium, titanium, and rare earths from aqueous media is actually impossible due to their largely negative redox potentials, nonaqueous media such as aprotic organic solvent and high-temperature molten salts have been employed for the electrodeposition of these metals. Room temperature molten salts (RTMS),1, 2) or room temperature ionic liquids, have also been developed as a promising electrolytes for the electrodeposition of base metals. In this field, chloroaluminates of alkylpyridinium or alkylimidazolium cation have been well investigated for aluminium3) or alluminium-alloy4-5) electroplating media. On the other hand, in order to avoid high hygroscopicity arising from the use of aluminium chloride, attempts have been made to combine the alkylimidazolium cations with fluorine-containing hydrophobic anions, e.g. BF4-,6) CF3SO3- (TfO-),7) (CF3SO2)2N- (Tf2N-),8) and H(HF)n-ions,9) and investigated for electrodeposition media.'°) Recently, a new series of RTMS consisting of tetraalkylammonium cations and Tf2N- anion, sometimes abbreviated as TFSI- anion, was found independently by MacFarlane et al.11, 12) and Matsumoto et al. 13) This type of RTMS, which is commonly named ""ammoniumimide"" salt, has a wide electrochemical window of ca. 5 V and, thus, the RTMS seems to be suited for practical application as a solvent for the electrodeposition process. In this paper, we report the electrochemical behavior of copper species in an ammoniumimide RTMS, trimethyl-n-hexylammonium bis(trifluoromethanesulfonyl)amide (TMHA-Tf2N)."

Jan 1, 2000

By Xueqin Li, Xuewei Lv, Yu Zhang, Wenchao He

In order to make full use of the chromium-bearing vanadium titanium magnetite with chromium, a new process of “direct reduction-electric furnace smelting separation” has been developed for recovering the iron, vanadium, titanium and chromium in recent years. In this paper, FactSage, one of the most frequently-used thermodynamic calculation software, was used to calculate the reduction degree of Fe, V and Cr with different n C/nO (mole ratio of carbon and oxygen). It was found that the suitable operating conditions of direct reduction process were n C/nO > 1.07 and T > 1473 K. In addition, the direct reduction experiment of Hongge vanadium titanium magnetite was carried out and the obtained samples after direct reduction were analyzed by XRD and chemical composition. The result shows that the metallization rate of carbon-containing pellet is nearly 90%.

Mar 1, 2018

By Wei-Tong Du, Zheng-Lei Guo, Yu Wang, Shu-Chao Wang

The influence of bottom blowing a CO2–O2 mixture on the bath temperature of a vanadium extraction converter was studied by using the characteristics of CO2 with weak oxidizing. It was studied in two aspects: oxygen content and temperature. The experiments showed, when the ratio of the mixture of CO2–O2 was 2:8 at 1300 °C, the bottom blowing of the converter inhibited the heating up of the hot metal, thus keeping the temperature below the carbon vanadium transition temperature. At 1360 °C, the sensible heat absorption by CO2 was 1.44 times that absorbed by O2 per mole. Meanwhile, at 1300 °C, 20% CO2 released the chemical heat of 13.58 kJ. So with the increase of the CO2 ratio, the bath temperature was reduced. The research showed that the bottom blowing of a CO2–O2 mixture had an advantageous effect by decreasing the temperature of the vanadium extraction converter.

Mar 1, 2018

By W. E. Wallace, J. A. Warren, D. Josell, D. Wheeler

"We present the results of experiments and modeling of flip-chip geometry solder joint shapes under shear loading. Modeling, using Surface Evolver, included development of techniques that use an applied vector force (normal and shear loading) as input to determine a vector displacement of the pads connected by the solder joint (standoff height and misalignment). Previous solutions solved the converse problem: fixed displacements used to determine required applied force. Such solutions were inconvenient for applications, where the applied force (chip weight) is known. Also, for geometric and materials studies of solder joint shapes involving multiple parameters, determining the equilibrium displacement from applied force by bracketing solutions could become computationally expensive. Measurements of solder joint standoff height and misalignment as functions of the applied force (normal and shear), solder volume and pad diameter are presented. Experiments were carried out for solder ball diameters from 0.38 mm (0.029 mm3 volume) to 0.15 mm (0.0019 mm3 volume) on pads of diameter 0.64 mm and 0.35 mm. Fitting of simulation to experimental results gave optimized values for the contact angle and surface tension of the solder which were consistent with measured and literature values. IntroductionIn packaging technology flip-chip has become an important method for attaching semiconductor devices to substrates. Generally, the chip and substrate are bumped with solder and then the chip is flipped onto the substrate and the solder reflowed to form conductive interconnects. An epoxy underfill is normally flowed between the substrate and chip to reduce the thermal fatigue on the solder joints. A flip-chip assembly is illustrated in Figure 1.In flip-chip applications, the use of an integrated underfill/solder bump system [1, 2) removes an extra process step, namely infiltration of the underfill. However, the presence of an underfill will retard the self-alignment of the flip-chip. A first step in understanding and predicting this retardation is to develop a model to describe normal and lateral force-displacements curves when underfill material is not present. At this stage it is unclear whether static surface tension theory is sufficient to describe a complete model for flip-chip realignment even without underfill."

Jan 1, 2001

By I. G. L. Sinclair

The Selbaie deposit is located in northern Quebec. It is comprised of three distinct, but genetically related, Cu-Zn-Ag ore bodies which also contain economically significant amounts of Au. The deposits are Archean in age and volcanogenic in origin. At Selbaie, ore microscopy has been employed to aid in planning of ore beneficiation methods and to monitor the ongoing performance of the concentrator. Examples of both types of study are described. Early in the life of the mine, excessive amounts of Zn appearing were found to be appearing in the Cu concentrate. Microscopic examination of concentrates showed that this was being caused by the presence of coatings of supergene chalcocite on sphalerite grains. Fine coatings of supergene galena and chalcopyrite were also observed on some sphalerite grains. The presence of Ag and Au in the ores makes an important contribution to the revenue of the mine. The various modes of occurrence and mineralogical relationship of these two metals are described and discussed. Monitoring of the ongoing concentrating process at selbaie is done by qua-litative and quantitative examination of products collected at various points along the circuit. Causes of such problems as excessive loss of metals to the tailings or inefficient recovery of individual metals, can often be identified and possible solutions proposed.

Jan 1, 1989

By Ruirui Wei, Mingrui Yang, Xueqing Li

Ultrasonic vibration was introduced into calcium ferrite (CF) melt in order to develop a new sintering process. Based on the acoustic refraction and reflection principles, ultrasonic propagation between amplitude transformer and CF melt has been analyzed and discussed. In addition, numerical simulation of ultrasonic propagation in CFmelt has also been carried out using finite element method. The distribution of acoustic pressure in CF melt were obtained, and the effects of ultrasonic power and frequency on acoustic pressure distribution were also investigated. The results show that increasing ultrasonic power promotes the acoustic pressure amplitude in the CF melt, while increasing frequency decrease the acoustic pressure amplitude. The acoustic pressure amplitude with the frequency closer to the resonant frequency may get the best cavitation effect because its average acoustic pressure is greater than those of others.

Mar 1, 2018