Search Documents

By Henrique Kahn

The Anitapolis alkaline massif in southern Brazil underlies a sub circular area of 6 km2. Bore-hole data show a concentric rock distribution, with mafic rocks in the central part and felsic rocks in the border zone. The rocks are covered by talus and weathered material, 30 m thick on average, and very inhomogeneous in composition. Phosphate mineralization associated mainly with two levels of the weathering mantle and with fresh rocks. A preliminary ore-type classification was based on distribution of apatite, feldspar, vermiculite, biotite-phiogopite, calcite, pyroxene, amphibole and analcime, determined by semiquantitative diffraction method. Technological tests performed on eluvial ore samples from three adits resulted in a subdivision of ore-types based on the difference in behavior due to mineral characteristics during mineral pr

Jan 1, 1991

By Mark Kramer

This paper is limited to treatment of bottom and fly ash waste resulting from WTE and RTE Cogeneration plants, commonly known as trash burners. The body of the paper defines waste generation and conventional treatment schemes. This paper does not identify a best treatment, however, it does offer a general perspective of the treatments to lead the reader to further investigation. Advantages and disadvantages of the ash treatments Is discussed in each treatment section.

Jan 1, 1996

By Mohamed Ahmed, A. Kawy

"Smelting of scrap copper and residual anodes and cathodes carried out in a reverberatory type furnace. In this, deoxidation process is carried out by wood, which acts as a resource of reduction gases such carbon monoxide, hydrogen and methane. Use of wood causes the formation of soot pollutants and efficiency of oxygen removal from copper is low leading to added costs in removing contaminants. This expensive problem was solved by using of reformed natural gas as a source of reduction gases (CO+ H2).IntroductionThree reverberatory furnaces were used for smelting of scrap copper and residual anodes and cathodes. Each furnace had a 7tpd capacity and was operated at 1183 °C.In this furnace, Step1-compressed air supplied by tubes from the side of the furnace to remove sulfur from copper matte by oxidation .The copper is also oxidized to copper oxide .[1]Step 2- copper from matte is deoxidized by a reductant. Typically deoxidation process is carried out using wood as a resource of carbon monoxide, hydrogen and methane which are the reduction gases. Use of wood causes the following:1- Forms soot pollutants2- Oxygen removal efficiency from copper is low; more contamination in copper matte increased energy in deoxidation3-the process is highly expensive.In the recent trends, this problem has been solved by using reformed natural gas as a source of reduction gases (CO+ H) .This results in 1-Reduced pollution during smelting.2- High efficiency in the removal of oxygen from copper to produce oxygen free copper. The surface of copper produced from this method is smooth which helps in forming and machining.3- Low cost and natural gas is more readily available in Egypt than wood."

Jan 1, 2010

By D. Y. Wang, G. Y. Sha, X. L. Shen, D. R. Gu

The study of the volatilization kinetics of zinc and lead in pellets made of zinc-leadbearing dust mixed with coal powder, in a nitrogen atmosphere and at a temperature range between 1100 °C and 1300 °C, shows that the reduction temperature has a significant effect on the volatilization rates of zinc and lead, and that both the particle size of the coal powder and the extra carbon content has no effect on the volatilization rates. The obtained activation energies for the volatilization of zinc and lead are 79.42kJ/mol and 88.74kJ/mol respectively. The volatilization rate of zinc is controlled by the reaction between the zinc oxide and carbon monoxide while that of lead is controlled by the lead evaporation reaction, and the diffusion of gaseous lead through the gas boundary layer covering the surface of the reduced liquid lead.

Jan 1, 2000

By P. R. Taylor

Titanium carbide and titanium diboride powders have been successfully synthesized by direct treatment of ilmenite concentrates in a non-transferred arc thermal plasma reactor. Methane gas was used as the reducing agent and boron oxide was used as the boron source in these processes. Free energy minimization plots were used to predict the behavior of each system under different molar ratios and operating conditions. Products were characterized by XRD, SEM and chemical analytical techniques. The average size of the ceramic product is in the submicron range. Metallic iron apparently is finely deposited on the surface of the titanium carbide or titanium diboride particles. Minor impurities such as silica, manganese and zircon were converted to the carbide form.

Jan 1, 1995

By Erwin Flender, Preben N. Hansen, Peter R. Sahm

"Until now FDM-Techniques have been widely used for Modeling Solidification Processes in Castings. Often a rigid, regular type of enmeshment (cubes, , --) have been used. This has the advantage of low CPU-costs, but the disadvantage of a zig-zag presentation of the interface between the casting and the mold. The last point is the reason why FEM-Techniques, giving the possibility of a true presentation of the shape in the enmeshment, are increasingly used. The disadvantage is the high CPU-costs. In this paper, a technique is presented, which uses the FDM-Mesh with the zig-zag presentation of shape and ADI-Algorithms to calculate temperatures and gradients. The new idea is that the calculated parameters are not presented related to the mesh in which they are calculated, but displayed using the true shape of the casting. Such an advantage of both low CPU-costs and shape correct presentation of the calculated results are achieved. IntroductionThe main reason for using a regular type of enmeshment is that it gives the possibility, via ADI-Algorithms, of obtaining a very fast FDM-Technique. The technique presented by P.R. Sahm and P. N. Hansen (1984), and also used by E. Flender (1985), is numerically so stable that average time steps, at least 200 times larger than the limit given by the explicit FDM-Technique, can be applied. To obtain reasonably good results, average time steps in the range of 20 to 50 times the explicit limit seems to be applicable. It should be pointed out,however, that FDM-Techniques can be used on arbitrary nets, the disadvantages being the same as for the FEM-Techniques. This has, among others, been discussed by P.R. Sahm and P.N. Hansen (1984)."

Jan 1, 1986

By Alwin Frei, Aldo Steinfeld, Peter G. Loutzenhiser, Enrico Guglielmini

"Using concentrated solar radiation as the energy source of high-temperature process heat, the carbothermal reductions of Al2O3 to Al and SiO2 to Si were examined thermodynamically and demonstrated experimentally at vacuum pressures. Reducing the system pressure favors Al(g) and Si(g) formation, enabling their vacuum distillation and avoiding contamination by carbides and/or oxycarbides. Exploratory experimentation in a solar reactor was performed with mixtures of charcoal with alumina and silica in the ranges of 1300-2000 K and 1997–2263 K, respectively, at 10-3 bar by direct exposure to concentrated thermal radiation. Distilled samples contained up to 19 wt% of Al in Al-Al2O3 mixtures and 79 wt% of Si in Si-SiO2 mixtures. When the reducing agent is derived from a biomass source, the solar-driven carbothermal processes are CO2 neutral.IntroductionMetallurgical extractive processes for producing Al1-2 from Al2O3 and Si3-6 from SiO2 are characterized by their high specific energy consumption and concomitant emissions. Alternatively, concentrated solar energy can be used as a high-temperature heat source to drive the carbothermal reductions and, thus, avoid greenhouse gas emissions and other pollutants derived from fossil-fuel-based processes7-12. When the reducing agent is biomass charcoal, the solar-driven carbothermal reduction is CO2 neutral. The carbothermal reductions of Al2O3 and SiO2 are represented by the simplified overall stoichiometric reactions:"

Jan 1, 2011

By Jorge Alberto Soares Tenório, Denise Crocce Romano Espinosa, Viviane Tavares Moraes

"The development of mobile phone technology has increased the replacement of outdated equipments for more modern models, transforming disposal of such devices into a serious environmental problem. Recycling appears as an attractive alternative to minimize the environmental impact of disposing such large quantities. Recycling can be accomplished by treating the printed circuit boards of used mobile phones by using the same techniques used in ore treatments with hammer mill; magnetic separation, electrostatic separation and grain size range. Before performing the recycling process a PCB characterization was performed to identify the fraction with the higher metals concentration/content. This study demonstrated that the electrostatic separation was not the best metals concentration of PCB aiming the recycling, while the non-magnetic residue had presented a more significant metal concentration. Furthermore, after the magnetic separation was possible to separate the following metals: iron and nickel.IntroductionPortable electronic devices have gained increasing acceptance over the last decades. Mobile phones sales in Brazil, for instance, have reached 104 million in 2007, and 128 million in 2008. It is estimated that, around the world, 100 million mobiles are thrown away every year, either because of loss of functionality or because newer models are launched in the market [1,2, 3]. Printed circuit boards in mobile phones are made of many materials, with approximately 83% in weight being metals and fiber-glass, and the balance being plastics pl. Several metals can be recovered from the electronics waste, such as copper, tin, iron, lead, nickel, titanium, aluminium as well as some precious metals such as gold, silver and palladium [4, 5, 6, 7, 8]. Concurrent with the increasing world demand for copper, there average metal content in ores has been decreasing. Economically interesting copper mines used to have 4% metal content, whereas presently, such content is around 1%, i.e., for every 1 ton of ore extracted, only 10 kg are copper [9, 10]. Approximately 33% of printed circuit boards (PCBs) composition is copper, that is, for every 1 ton of PCBs waste, 330 kg are copper [1]. Research in recycling PCB waste focuses on mechanical, electrometallurgy, pyrometallurgical and hydrometallurgical processes [3, 8]. Collecting and recycling obsoletes electro-electronic equipments is very important these days, in order to, not just preserve the non renewable natural resources but also to keep the environment and the population safe from the pollution caused by the toxic materials and heavy metals present in this kind of waste."

Jan 1, 2011

By Ernt. W. D.

A membrane based mixed extractant process was developed for selective removal of copper from waste acidic cupric chloride etchant solutions found in printed wire board manufacturing. The process uses a mixture of Adogen 381 (tri-isooctylamine), MOC®-45 (ketoxime) and MOC® 55TD (aldoxime) in a kerosene diluent. The mixed extractants recover the copper from a hydrochloric acid medium and transfers it to a sulfuric acid medium. The process also utilizes unique wetted membranes to separate the aqueous and organic phases. The driving force for these membranes is not pressure but the difference in surface tension between the two phases. By using these membranes, complete phase separation results. There is no physical entrainment contamination as found in conventional systems. The only cross contamination is the solubility concentration of one phase in the other. This however is less than 10 mg/l.

Jan 1, 1998

By I. Gaballah

The kinetics of oxychlorination of pure CI-2O3 with C12+02 gas mixtures is studied by ThermoGravimetric Analysis (TGA) in non and isothermal conditions up to 1000 °C. The reaction of Cr2O3 with C12+O2 chlorination gas mixtures starts at about 550 °C and the reaction product is CrO2Cl2. The oxychlorination rate of Cr2O3 is almost proportional to the chlorine partial pressure and to the fourth root of the oxygen partial pressure in the chlorinating gas mixtures. At 800 °C, the maximum chlorination rate is obtained using a gas mixture having a C12/O2 ratio equal to 4. The apparent activation energy of the oxychlorination reaction of Cr2O3 is 87 and 46 kJ/mol at temperatures lower and higher than 650 °C, respectively. By varying the chlorine and the oxygen partial pressures of the oxychlorinating gas mixtures at temperatures higher than 550 °C, it is possible to extract selectively the chromium chlorinated compounds from the chromium bearing materials. a. Laboratoire Environnemem et Minéralurgie, BP 40, 54501 Vandceuvre, France, b. École Nationale Supérieure de Géologie, Rue du Doyen Marcel Rouhault, 54501 Vandoeuvre Cedex, France, c. Centre National de la Recherche Scientifique, 3 rue Michel - Ange, 75794 Paris Cedex, France, d. Insritut National Polytechnigne do Lorraine, Rue de la Font de Haye. 54501 Vandceuvre Cedex, France.

Jan 1, 1997

By Mingchun Lu, Zhe Wang, Mingming Cao, Xiangdong Xing, Shan Ren, Jianliang Zhang, Zhengjian Liu

"The effect of reduction temperature on the vanadium titano-magnetite carbon composite pellets was investigated by X-ray diffraction (XRD) and scanning electron microscopy (SEM), and the discussion has put emphasis upon the enhanced reduction mechanism of additives containing CaF2 and NaF in this paper. The results showed that the reduction temperature of 1350°C was needed for the generation, mergence and growing up of metallic iron as well as monomer dissociation between metallic iron particles and slag phase in the vanadium titano-magnetite metallization pellets. The iron compound was completely reduced into metal iron, and Fe2Ti04 was mainly transformed into metal iron, (Fe,Mg)Ti205 and FeTi03 at 1350°C. The maximum metallization ratio was only 88.5% at 13500 for 30 min without any additive. However, with the addition of 3.0% CaF2 or NaF, the metallization degree of pellets could reach up to 94.8% and 92.5%, respectively.IntroductionVanadium titano-magnetite which is mainly distributed in the area of Panxi, Chengde and Maanshan in China is a kind of complex iron ore which contains various valuable metal elements such as iron, vanadium, titanium, etc. Among the above areas, Panzhihua (Sichuan Province in China) area possesses the largest deposits of vanadium titano-magnetite and the future reserves are more than 100x108t, and the reserves of Ti existing as Ti02 reach to 8.7x108t which occupy over 91% of the whole nation and ranked No.1 in the world[1]. Lots of researches on the comprehensive utilization of vanadium titano-magnetite have been conducted in the world. And many technological processes have been applied successfully in industrial production. Among these processes, the process of rotary kiln-electric furnace is employed to recover iron and vanadium in South-Africa, while the process of blast furnace-rotary furnace is widely used in Russia and China. Besides, many researchers have made efforts on employing new direct reduction process to realize the effective comprehensive utilization of vanadium titano-magnetite[2-4]. However, the direct reduction process is only researched in laboratory and it has not been used in industry."

Jan 1, 2013

By Andre L. De Vegt

Hydrogen sulfide is an expensive chemical used in nickel, zinc and copper mining and metallurgical operations for selective recovery and concentration of metals, from leach water streams, acid plant blow down streams, refinery electrolyte bleeds and precious metal, plant bleeds. Hydrogen sulfide is either produced on site by catalytic reduction of elemental sulfur or transported to the site as liquefied hydrogen sulfide (H2S) or as a sodium sulfide solution (NaHS) Biologically produced hydrogen sulfide has economically very interesting, application possibilities in the mining and metallurgical industry. Converting sulfates from waste streams into usable hydrogen sulfide by biological reduction results in operational cost savings in existing lime treatment systems. H2S can be produced biologically for less-than $500/ton S. For the past ten years Paques has been engaged in the development and installation of treatment systems based on biotechnological processes to remove sulfur compounds from water, air and gaseous streams. Paques has designed and installed a groundwater treatment system for the Budelco zinc refinery in the Netherlands to remove sulfate and heavy metals. The hydrogen sulfide produced is used for recovery of metals,, mainly zinc, from the ground water stream. The system has been operating since May 1992 treating a flow of 5000 m3/d. At Kennecott's Bingham Canyon Utah copper mine, a pilot plant started operation in November 1995 to develop the process for selective recovery of copper from leach water using biologically produced hydrogen sulfide from sulfate containing groundwater. Other pilot plants are operated at DOE's Pittsburgh Research Center and at Cominco Research focusing on selective recovery of metals.

Jan 1, 1998

By W. D. Cho

The slag chemistry in steel processing plays an important role in terms of the removal of impurities including alumina particles. In the present study, the dissolution of solid alumina particles in CaO-based fluxes at the temperatures between 1450 and 1550 °C has been investigated to determine dissolution kinetics and mechanism. Alumina particles were added directly in the slags and the size of alumina particles was measured as a function of time using optical and scaru;ling electron microscopes. The dissolution rate has also been obtained as a function of Si02, CaF2, MgO and MnO contents in the slags. The diffusion boundary layer between alumina and bulk slag phase has been observed and analyzed using SEM and EDX. In addition, some experiments have been performed for the dissolution of alumina in BaO-based fluxes.

Jan 1, 2003

By W. K. Tolley

The U.S. Bureau of Mines (USBM) is currently investigating improved technology for mineral flotation. A variable often neglected in flotation control is redox potential. The use of redox control is illustrated by the separation of molybdenite from chalcopyrite. Laboratory testing showed that redox potential had a greater effect on product quality than collector addition. A significant need in froth flotation is greater reliability of the sensors used in measuring and controlling redox potential in mineral slurries. The USBM has developed an automated method for removing scale and reconditioning gold redox-sensing electrodes. Fouled electrodes are anodically polarized to 1.2 V versus the AglAgCI reference potential to remove scale. The electrodes then are conditioned by a brief potentiodynamic treatment to re-establish electrochemical equilibrium. In laboratory tests, this technique removed calcarious deposits from gold electrodes and reconditioned them for useful service in approximately 10 min. In plant practice, this technique would obviate the need for plant operators to manually polish electrodes, and also should result in greater reliability in redox measurements. Inexpensive, automated equipment to condition electrodes in a plant setting is described.

Jan 1, 1995

By W. K. Choi

Stainless steel exposed to wet environments at ambient temperature is subject to the formation of a surface biofilm. Depending upon the prevailing environmental conditions (dissolved oxygen, pH, Eh, concentration of cationic/anionic species), the biofilm may stimulate corrosion through formation of differential aeration zones and concentration cells. Corrosion significantly impacts the United States economy, since on a yearly basis, corrosion induced losses are estimated to be over $200 billion. A large portion of this corrosion is imputable to bacterial activity, and basic information is needed for a better understanding and control of the biocorrosion phenomenon. The present study has investigated the influence of Thiobacillus ferrooxidans in the corrosion of American Iron and Steel Institute (AISI) 304, 316 and 416 stainless steel samples. The formation of biofilm and microstructural changes on the surface of stainless steel samples and their weldments were assessed by microscopic examination, and the changes in the mechanical properties by stress-strain measurements. The significance of the results will be discussed.

Jan 1, 1993

By Pinakin C. Chaubal

Today?s steel industry is in a vibrant and resurgent mode. This transformation has been in the making for some time now. Over the last few decades, the industry was steadily transforming itself into becoming a high tech industry. New technology was adopted, efficiencies were enhanced, lean manufacturing concepts were brought in and a strong customer focus was developed. Today?s mills employ sophisticated instrumentation, computerized monitoring, on-line smart systems etc. driving processes that are producing at rates of many tons/minute. All this is not possible without judiciously using the latest available technologies in various fields and developing a more sophisticated work force. Prof. Sohn has been a pioneer in driving the concept of process engineering in process metallurgy. In this paper the focus is on some aspects of process engineering ? primarily process modeling - as applied to iron and steelmaking processes. Examples are shown to demonstrate how problems have been addressed. Some thoughts on future directions are presented.

Jan 1, 2006

By Hong Ro Lee, Seang Suk Cho, Byung Sun Chun, Chang Whan Won

"The preparation of Al203-SiC-TiC composite powders was studied by SHS process using silica (source of Si02) powder instead of Si which is expensive. And, aluminum powder was used as reducing agent of silica and charcoal activated was used as carbon source. Effects of the molar ratio in raw material mixtures and compaction pressure and initial temperature of reactant on the products and combustion process were studied. The most important variable affecting the synthesis of Al203-SiC-TiC was the molar ratio of carbon. The combustion reaction generated in powder state without preheating. But the unreactants exist in the product on all molar ratio. When the preheating temperature is over 400 °C, the combustion reaction was able to be generated in pellet state. Without preheating, the combustion reaction was possible by Ti02 addition. The optimum condition in this system was the molar ratio of Si02:Ti02:Al:C=2.5:0.5:4:3.1. INTRODUCTIONCeramics have demonstrated a capability as a cutting tool, especially in competition with WC-Co cermets (ceramic-metal composites) as inserts for metal turning and milling operation. The advantage of ceramics compared with carbides is retention of high hardness, strength, and chemical inertness to temperatures in excess of 1000 ·c . This allows use of the ceramics at much higher machining speeds than can be tolerated by carbides. However, the ceramics have lower toughness than the carbide materials, and have only been used successfully in the limited operations of turning and milling. There are several classes of cutting tools. The addition of TiC or PSZ, or both, and reinforcement with SiC overcame the poor fracture toughness and thermal-shock resistance that limited Al203 use in the past [1]."

Jan 1, 1998

By M. Misra

Acid mine drainage from reactive sulfide tailings is a major environmental concern facing the mining and mineral industries. A preventive technique to control acid mine drainage by agglomeration and encapsulation process is presented in this paper. The reactive tailings are agglomerated using Portland cement type I1 as binder. The cold bonded agglomerates after specified curing period are, strong and resistance to weathering. The leaching and weathering experiments have shown that a significant reduction in the concentration of dissolved metals can be observed with the agglomerates as compared to as- received tailings. Addition of small amount of sodium silicate during agglomeration increases the strength and develop good resistance to weathering by forming a glassy coating and elongated crystals within the agglomerates.

Jan 1, 1993

By Hong Ouyang

A unified computational model has been developed for the Bridgman growth processes of B-NiAI and CdTe crystals. To handle the geometrical and physical complexities, a two-level approach has been developed. At the gtobatlevel, conjugate heat transfer, phase change dynamics, and variable material properties along with the realistic geometries and thermal boundary conditions are accounted for inside the entire crystal growth system. Refined calculations are then made within the ampoule, with the boundary conditions supplied by the global simulations. This model can optimize the use of computational source, help understand solidification behaviors, and improve designs of crystal growth system.

Jan 1, 1996

By Kenneth L. Driggs

The Environmental Protection Agency's Clean Air Act of .1970 provided the driving force for the current Magma Smelter configuration. The historical and technical perspectives of those process developments are reviewed. Innovations in procedures and equipment have allowed compliance with the requirements of the regulating authorities. The wet scrubbing of converter gasses and the monitoring of converter operations by a controlling foreman are two of the major contributors to these successes. The Clean Air Act Amendments of 1990 have posed many new concerns for all U.S. industry, including the few (seven) primary copper smelters remaining. Future concerns include tightening the sulfur dioxide ambient standard from the current three-hour averaging period to one hour"

Jan 1, 1992