Search Documents

By Wang Zhi

High-Mg-content concentrates are usually treated in Jinchuan flash smelting Furnace. Because the viscosities of high-Mg-content slag is very high, the operation of flash smelting becomes very difficult. To solve this problem, the viscosities of the semi-synthesized FeO-MgO-SiO2 slag of different compositions were measured. The results showed that when in the slag the weight percentage of MgO [w(MgO)] is 6-10%, the ratio of the weight percentage of iron to that of Si02, w(Fe)/w(Si02) is 1.1-1.4 and the temperatures are within 1473-1773K, the slag viscosities increased with the increase of W(MgO) and w(Fe)/w(SiO,). When w(Mgo)<6%, the smelting temperature should be controlled at I 300°C in order to to keep the smooth operation. When w(MgO)>10%, the temperature should be kept above I 633K. When the content of MgO is higher, a lower viscosity slag can be produced by decreasing the ratio of w(Fe)/w(SiO,). The appropriate ratio of w(Fe)/w(SiO,) for Jinchuan flash smelting furnace is about 1.2.

Jan 1, 2003

By Jan Vrestal, Josef Tomiska, Pavel Broz

"Thermodynamic investigations on fcc solid ternary Fe-Ni-Cr alloys have been performed by means of the computer-aided Knudsen cell mass spectrometry. Ternary T.AP.-series (Thermodynamically adapted power series) are used for the algebraic representation of the thermodynamic excess properties. At 1650 K the molar excess Gibbs energy GE is negative over the whole field of stable fcc phase. The molar heat of mixing HE is exothermic in the predominant part of the fcc phase field. Only between the section with a constant ratio of mole fraction Xcr/XNi = 0.64 and the fcc phase field boundary the HE values are slightly endothermic. The results of this work can be used successfully for phase diagram calculations.IntroductionThermodynamic investigations on multicomponent alloy systems such as the Fe-Ni-Cr ternary system including the three binary boundary systems are very time-wasting and usually beset with considerable experimental difficulties. Additionally, the required experimental equipment is very expansive and the obtained results are not always satistying. Therefore it is understandable that many phase diagram calculations are based only on few experimental values of the molar excess free Gibbs energy GE. Consequently, Kundrat and Elliott [1] as well as Hillert and Qiu [2] used in their reassessments of the phase diagram of the Fe-Ni-Cr system thermodynamic data mainly assumed and/or optimized by means of various reasoning.Lee [3] reported recently, a revision of the used thermodynamic description of the Fe-Ni liquid phase is necessary to obtain a better agreement with the experimental data on the bcc/liquid or fcc/liquid tie lines and liquidus temperatures in the Fe-rich region of the Fe-Ni-Cr ternary system than in the previous assessments. This is 'in full agreement with mass spectrometric investigations of Fe-Ni alloys in the liquid and in the fcc solid phase, published earlier [4,5]. Indeed, phase diagram calculations based upon the molar excess free Gibbs energies GE obtained in these studies yield liquidus and solidus lines in excellent agreement with experimental phase diagram data [5]. Nevertheless, these experimental data have not been considered later on any more, not even in the revision by Lee [3]."

Jan 1, 1996

By Stephen Northey, Nawshad Haque, Terry Norgate

"Life cycle assessment (LCA) is a recognized tool to evaluate various processing routes for metal production. Declining ore grades and higher specific energy requirements for primary metal production put greater emphasis on recycling. Greenhouse gas (GHG) emissions of steel and aluminium metal production were quantified with recycling scenarios using material recovery facility (MRF) data from the database of SimaPro LCA software. The GHG footprint of the MRF is relatively minor compared with that of associated transport during collection (i.e. 10 times more than MRF) of curbside recyclable material. Additionally, if the bulk recyclable material is sent overseas (i.e. Australia to China) from the MRF for further processing, the GHG footprint of shipping can significantly be larger compared with the sum of the collection and MRF (assuming electricity is from same source). Thus opportunities exist for reducing GHG emissions from secondary metal production if it is processed close to the MRF.IntroductionIt is a challenge to recycle metals significantly, although theoretically infinite recycling is possible due to their elemental nature. Leaks from the metal stocks in society occur through corrosion, wear and dispersive uses, or via land filling or similar activities that return metals to the earth. In order to provide a technically sound and transparent assessment of metal recycling, a methodology such as life cycle assessment (LCA) should be used. By taking a life cycle perspective, the beneficial recycling properties of metals can be evaluated in a manner that enables appropriate comparisons with other materials or product systems that do not have recycling loops. In practice, mixtures of primary and secondary metals are often used in new products, and also at the end-of-life various processing methods are used for recycling.The difficulty of introducing recycling into LCA is to set the right boundaries for the different flows ending in different product systems. It is a question of which observed material flow belongs to the first product system and which one to the second or subsequent systems. Recycling can be part of any product LCA. However, it is often a complex issue which requires specific considerations. As pointed out by Yellishetty et al. and Birat et al. [l, 2], LCA practitioners are left with much freedom in allocation of environmental burdens to account for recycling, thus making subjective judgments on recycling and allocation of credits to recycling. This often makes it difficult to compare the results of LCA studies conducted by two different practitioners even on the same processes. As LCA is often used to define policy in government, business and society circles, it should be based on a sound, objective and unbiased description of recycling."

Jan 1, 2014

By Frank Field, Elsa Olivetti, Randolph Kirchain, Elisa Alonso, Gabrielle Gaustad

"The primary technological challenge to increased use of secondary raw materials is the presence of undesirable elemental species in scrap streams. Recent literature indicates that this may become exacerbated by accumulation of impurities over time. Devising strategies to mitigate this problem depends upon understanding the mechanisms of accumulation. This paper takes a first step at characterizing the extent of this issue by presenting a simple analytical model of recycling rate for materials experiencing exponential growth. Low potential recycling rates limit accumulation due to dilution. Empirical analysis of several major materials indicates that, even for current recovery rates, theoretical recycling rates can reach above 60%, making accumulation issues a possibility.IntroductionIt is well known that recycling of secondary materials can provide significant environmental and economic benefits. Energy savings, in particular, can be quite large when substituting secondary materials for primary. Nevertheless, over the past decade, the recycling rates within the U.S. of many materials appear to not be increasing as rapidly as one would predict or even at all (Figure 1). While many barriers exist to increasing materials recycling, one that is cited consistently by the literature and producers[1-3] is compositional limitations; that is the mismatch between the characteristics of secondary materials and those desired for the finished goods into which they would be transformed..One particular aspect of compositional limitations that is receiving increasing attention is the potential for progressive deterioration of the quality of secondary raw materials streams. For some materials, for example paper or polymers, this phenomenon is inherent and relatively rapid[4, 5]. As such, it is well documented and plays a significant role in recycling decision-making even for prompt or in-house material recycling. Conceptually, this issue can manifest in other secondary materials as well, albeit through a different mechanism.As materials are mixed, used, and reprocessed during recycling, they come into contact with and often pick up other elements. The presence of these, so-called, tramp elements alters the original known composition, possibly requiring additional measurement and processing and may even preclude economic, productive reuse; ultimately, this unintentional pick up is unwanted. A growing number of studies and literature would suggest that accumulation of unwanted elements is an emerging problem, in most recycled material streams. Table I provides a brief literature review of various recycled material streams and the accumulated elements noted as problematic by various authors"

Jan 1, 2008

By P. Halsall

Smelters of medium or low grade tin concentrates must recover a high proportion of tin from iron-bearing slags or concentrates; the volatility of tin sulphide makes possible the production of iron-free tin fume. Laboratory work defined conditions which would promote the sulphidisation of tin slags and concentrates melted with them, to result in tin recovery as fume, and a residue of less than 0.5% Sn content, which could be controlled to vary with the value of tin. Subsequently pilot-plant work on 6-tonne and 15-tonne scale led to a commercial plant of 45 tonne. capacity (1962), for melting and fuming primary and secondary low-grade tin materials by submerged combustion. Some factors contributing to the rate of Working expressed in terms of the &apos;half-life and the amount of work done, the &apos;half-life-tonne&apos; are studied, leading to the design and operation (1972) of the 100-tonne water-jacketed unit, presently in use, treating a wide range of slags and low tin-content ores and residues.

Jan 1, 1983

By Larry Southwick

This Peirce-Smith Converting Centennial symposium is celebrating the contributions of two men, William Peirce and E.A.C. Smith, in advancing technology allowing the copper industry to realize its full potential. However, theirs is representative of a larger story: New, simpler technology releasing the stranglehold of older, more complicated technology, new developments in vessel configuration and design finding alternate routes around dead ends in operability, advances in technique and concepts removing roadblocks of cycle time and capacity, and overall innovation opening up vast new reserves around the world to those companies willing to embrace those improvements. Our story is also one of personalities, stubborn smeltermen versus the innovators, those inside the industry versus those from outside. It is a story of an initial borrowing from the steel industry, but also Peirce and Smith, from the refining end of the copper business, taking the ideas of Baggaley from Pittsburgh’s steel and airbrake industry, who built on what Hollway, Manhès and David, Douglas, and others had done in smelter tests, further to compete with the previous primacy and closely held expertise of the copper smeltermen in Wales. These advances have been well recorded in photographs taken over the last 150 years. A number were submitted especially for this symposium. Many others were published in the mining and metallurgy press of the times. Several mining schools also retained copies of photos either taken during field trips, or donated to the school by alumni and operating companies. This presentation will provide a selection and discussion from these sources of “converters in action”, describing the various designs, operations and developments depicted. The focus here will be on the first roughly 60 years of copper converter development, from Bessemer’s days at the dawn of this new idea, up to and slightly past the time of initial adoption of Peirce and Smith’s designs.

Jan 1, 2009

By J. Rastas

The recovery of lead, silver and gold from existing and potential zinc process residues using a sulfidization-flotation method was investigated on a laboratory scale. The following residues were tested: neutral leach residue, high acid leach residue, and hematite residues. The sulfidization of lead and silver is carried out at low pH by the addition of a stoichiometric amount of sulfide at a controlled rate. To increase the particle size of the sulfides, seeding with synthetic lead and silver sulfides -is employed. The flotation is carried out at pH 2-4 using low pH-collectors such as dithiophosphates and dithiophosphinates. Special attention must be paid to the role of oxygen in the conditioning stage. The effect of different parameters on both the sulfidization and the flotation has been evaluated. Recoveries of 85-90, 90-95 and about 80 % were obtained for lead, silver and gold, respectively. Typically, concentrates containing 50-60 % lead, 3-5 kg/t silver and 10-15 git gold were produced.

Jan 1, 1990

By S LeClair

Intelligent manufacturing involves intelligent, product-directed systems that facilitate the on-line, real-time generation of an improving product process cycle. A first step in the journey relates to self-directed systems which have the ability to reason and create their own processing paths in response to varying product and process conditions encountered during the process. This paper discusses an application of self-directed process control in the manufacture of graphite-epoxy laminated composites. An Air Force team involving researchers and production personnel have caused the development of a system now in use at the Air Force Logistic Center at McClellan Air Force Base in Sacramento CA. The paper discusses results and lessons learned in the process of trying to speed the implementation of research efforts which show significant potential of improving the product quality in less time and at less cost

Jan 1, 1992

By Xi-chang Shi, Yun-feng Fu, Bai-zhen Chen, Hui Xu, Xiang Xiao

"Extracting boric acid from saline brine by boron specific ion-exchange resin was investigated. Effects of resin amount, temperature, time and stirring speed on boron adsorption rate were studied in the experiments. The results indicated that the XSC-700 resin showed excellent boron absorbability and it performed better property for elution. The maximum boron adsorption capacity was 6.16 mg/ml in the optimum conditions: the resin concentration of 5 ml/(100 ml brine), the temperature of 60°C, the time of 5-6h and the stirring speed of 100 r/min. Boron was eluted from the resin with HCl and boric acid was crystallized by evaporating the eluate. The product of boric acid was in pure form as confirmed by XRD and other analysis techniques.1 IntroductionBoron has a number of minerals in nature such as tincal, colemanite, ulexite, and kemite, etc. [1-2]. Boron and its compounds are chemical materials of significant value. The principal industrial uses of boron compounds are in the production of glass, porcelain, enamels and detergents. Other uses include fertilizers, metallurgy, and nuclear shielding [3-4]. In recent years, because of the large-scale mining boron ore, ore resources are drained gradually. With the development of science and technology, the boron mineral resources will be unsatisfied with the future requirement. There exits abundant boron resources in salt lakes which cover about 40% of the total reserves in China. If we can obtain boron from salt lakes, it will produce great economic interests [5-6]. Therefore, actively seeking boron from salt lake and other resources in suitable conditions has become a hot spot in the research organizations of boron resources development and utilization in the world [7].There are many methods such as acid crystallization, solvent extraction and ion exchange processes suggested effective for boron extraction from aqueous solutions. Acid crystallization method has the shortcomings of complicated procedures, the pollution caused by hydrochloric and other ingredients returning to salt lakes during the extraction process. Although solvent extraction process increases the boron acid recovery efficiency, the cost of production is high [8-9]. However, Chelating resin extracting boron has the characteristics of simple process, easy operation and no pollution. It was reported that chelating resins containing functional groups show a high selectivity for boron extraction [10-12]. Therefore, ion exchange technique which is now the most practical application of significance and most extensively used ha"

Jan 1, 2011

By William Petruk

The development of automatic image analysers brought the application of image analysis into process mineralogy because the analysers can measure parameters more easily, quickly and accurately than by manual grain counting techniques, and can also collect data unobtainable by manual grain counting. Data from ore specimens and mill products are used to predict and to define the behaviour of minerals during processing. The analyses are generally performed on the basis of either surface areas or linear intercepts of grains in polished or thin sections, and the data are computer processed to give mineral quantities, liberations, size distributions, and characteristics of middling particles. For analysis, the minerals must be detectable and discriminatable from each other. An image editor is usually used when minerals are not easily discriminated. In addition BSE-8EM photographs have been used where the silicate minerals could not be discriminated from the mounting media. Methods of analysis, typical results, and their applications are discussed.

Jan 1, 1982

By K. Prashant Sarswat

Isotopes are critical to a variety of applications including physical science analyses, biology, medicine, pharmaceuticals, and national security. In most cases isotopes must be relatively pure or highly enriched before they become useful. Current isotope separation technologies are relatively inefficient, capital and labor intensive, and often produced by a limited number of suppliers. In the category of isotopes, lithium is among other important candidates. Lithium is found naturally in two isotopes, 6Li which accounts for 7.5% of all lithium, and 7Li which makes up the balance of 92.5%. Each of these isotopes is important to the nuclear industry. 7Li is often used in the form of lithium hydroxide which is used to control pH in pressurized water reactors. The current supply of 7Li is based mostly outside of the United States, and its long-term supply is uncertain. Apart from supply issues, the use of mercury for 7Li separation is also a concern in commercial processing using the most common and efficient approach [1–3]. Hence, a reliable, environmentally friendly, and efficient technique is needed to produce 7Li. In this line of investigations, the authors used a two-compartment system and significant separation was achieved. In this piece of research, some preliminary results are presented including cell design and actual isotope ratio after enrichment. Applying an electro-potential across two electrodes can be used to drive electromigration of Li isotopes. The electromigration is in addition to normal diffusion. Note that 6Li diffuses faster and hence there will be a lowering of the 6Li concentration near the positively charged electrode and an enhancement in 6Li near the negative electrode during the separation process. Similarly, 7Li will be more prevalent near the positive electrode and less prevalent near the negative electrode during the initial separation stage [1].

By T. Plikas, L. H. Gunnewiek, L. Oshinowo

"Electric furnace smelting is one of the principal unit operations for ferroalloy production, and increased process intensity, improved availability, minimal maintenance and a longer campaign life are common objectives for electric furnace operation in order to obtain favourable economics of production. Furnace designers have continued to develop innovative solutions, e.g., furnace cooling systems, that have allowed these objectives to be realised and CFD modelling plays a key role in the design process. Enhanced understanding of the energy transfer process in the furnace and the ability to develop, evaluate and optimize components of the crucible design to match process requirements are the key motivators for modelling.This paper provides an overview of recent applications of CFD to the design of electric furnaces. The aim is to illustrate what can be done, and identify areas where further work is needed in this field. Examples include furnace bath simulation, crucible cooling system design, taphole design, baking of Soderberg electrodes, off-gas systems, and fume control and building ventilation. It is argued that the trend is for numerical models to become more encompassing while at the same time more accessible, and therefore further improvements in furnace design will be realised with continued and well validated modelling efforts.IntroductionOne of the main processing steps in ferroalloy production is the smelting of ore in electric furnaces. The three-electrode, AC submerged arc furnace is most prevalent method for smelting in the industry, with shielded-arc and DC plasma arc furnaces achieving limited application (1,2). Commercial furnaces range in size from a few megawatts to more than eighty megawatts of supplied power, and operate with the objective of maximising the return on capital invested. Maximising productivity and energy efficiency are two pathways to achieving this objective, through process intensification, increased availability, minimal maintenance, and increased campaign life for the furnace and associated equipment. Concurrently, the need to reduce the environmental impact of metal production by controlling the emission of particulate emissions, greenhouse gases, and other harmful by-products must also be met."

Jan 1, 2004

By Zhi-biao Yin

Copper smelter flue dusts often cannot be directly recycled to the smelting process and accumulate as hazardous wastes requiring environmentally acceptable disposal. Because of the limited amount of flue dust, a separate copper extraction process must be simple and require-a small plant investment. A flue dust process has been developed, consisting of the following steps: (1) roasting a pelletized mixture of hydrated lime and flue dust to fix arsenic and sulfur as insoluble calcium salts, (2) heap leaching the roasted pellets with a buffered ammonia/ammonium salt solution to extract copper as an ammine complex in a lined cell that is the final repository of the leached pellets, and (3) boiling ammonia from the lixiviant to precipitate copper. Condensed ammonia and the filtered solution are returned to leaching. Heap leaching in the final repository cell lowers the capital investment significantly compared with competing extraction processes. Chemistry with respect to arsenic, sulfur and copper is discussed.

Jan 1, 1992

By Gerald M. Rich

Magma Copper Company, a subsidiary of Newmont Mining Corporation, has initiated many changes in the continuous casting of 5/16 inch diameter copper rod since startup of the San Manuel rod plant in early 1972. With rod production at forty percent over design capacity, many production records have been established including a record cast of 761 tons of salable rod in a twenty-four hour period. The most challenging and rewarding introduction was the continued utilization of an alloyed copper casting wheel in lieu of the conventional steel wheel. With proper cooling and careful control of the mold release agents. as much as 58.000 tons of copper were cast on a single copper wheel. Other advantages are: 1) Fifteen percent increase in available casting time 2) Reject rod from steel inclusions was reduced by nearly one-hundred percent 3) Wheel cost was decreased by ninety-one percent 4) Natural gas consumption dropped approximately fifteen percent 5) Large increase in refractory component life 6) Reduction of manhours/ton. Many other modifications have contributed to excellent rod quality and high operating efficiency. A two-piece launder was replaced with a single castable launder which reduced oxygen pickup and provided better slag removal. Modifications to the bar preparation unit, pickling system, and coiler resulted in considerably higher milling efficiency.

Jan 1, 1976

By C. S. Griffith

Lithium Australia NL (ASX:LIT) and ANSTO Minerals have been working together since 2015 on the development of halide accelerated leaching for the extraction of lithium from lithium-bearing micas, spodumene and clays. This technology has been termed SiLeach® process. The driving force behind development of the SiLeach® process, initially, was to develop a hydrometallurgical process to extract lithium from micas and spodumene without the need for the energy intensive, high temperature processing conventionally applied to lithium extraction. This driving force remains today and continues to hold promise in realising the value of previously under-utilised lithium resources. A comprehensive understanding of the technology and its applicability to the processing of micas and spodumene currently exists, and the flowsheet has been rigorously piloted. Production of battery grade lithium carbonate has been demonstrate

By Pengfu Tan

Electric arc furnace (EAF) dust from the steel industries is listed by the United Sates EPA as a hazardous waste under the regulations of the Resource Conservation and Recovery Act due to the presence of lead, cadmium and chromium. The disposal of the approximately 650,000 tons of EAF dust per year in the U.S. and Canada is an expensive and unresolved problem for the majority of steel companies. The Waelz process has been considered as the best process for treating EAF dust. A process model, combined thermodynamic modeling with heat transfer calculations, has been developed to simulate the chemical reactions, mass and heat transfer and heat balance in the kiln. The injection of air into the slag and the temperature profile along the kiln has been modeled. The effect of (CaO+MgO)/SiO2 on the solidus temperature of slag has been modeled also and discussed. Some optimizing results have been presented in this paper.

Jan 1, 2005

By Youliang He

Twin-roll casting is an integrated casting and rolling process that involves the continuous solidification of a melt and the plastic deformation of the solidified metal between two rotating rolls. Computer modeling is a valuable tool to help engineers understand the metallurgical process during twin-roll casting. However, commercially available software can only model either the fluid flow/heat transfer of the melt or the plastic deformation of the solid, but not both. In this study, an object-oriented finite element program was developed to simulate the steady-state fluid flow, solidification and plastic deformation of an A7,31 magnesium alloy in a horizontal twin-roll caster. The melt, the mush zone and the solid were treated as a generalized Newtonian flow in an Eulerian reference frame and different constitutive equations were employed to describe the material behaviours. The effect of operational parameters on the solidification process was discussed based on the simulation results.

Jan 1, 2010

By Tianzu Yang, Weifeng Liu, Lin Chen, Deyu Wang

"Due to the gradual exhaustion of easily extractive gold ores, it is vital to make efficient use of refractory gold ores which hold 30% gold storage of the world. However, the disadvantage of current processing technologies for refractory gold ores consists of severe pollution, low gold extraction ratio, high investment, etc, thus great research interests were attracted during recent years. This article provides an overview of the distribution and categories of the refractory gold ores in the world. The state of art in processing refractory gold ores by pyrometallurgy, hydrometallurgy and biometallurgy techniques and their industrial applications are highlighted. Potential environmental conservative techniques for efficient gold extraction are also reviewed.IntroductionResources of Refractory Gold OresAs easily extractive gold ores are going to be exhausted with the large scale mining nowadays, refractory gold ores are becoming more and more important. Gold in the refractory gold ore cannot be fully extracted using conventional method (cyanidation) even with fine grinding. The amount of gold in the refractory gold ores is about 1500~2000t in China, which occupies 30~40% of the total gold storage [1]. Therefore, it is vital to make efficient use of refractory gold ores."

Jan 1, 2013

By Zhang Yongzhu

In hydrometallurgical processes of PGMs separation and refining, differences between 1-PGMs (Ru;Rh;Pd) and h-PGMs(Os;Ir;Pt) in thermodynamics and kinetics have been observed. The successful practice in the separation and refining of PGMs in China, is mainly based on the following two kinetically extraction sequences of: (1) for the extraction of PGMs complexes in different configurations with coordination mechanism (AuCI,) -> (MCl6)2-> (MCl4 )2-> (MCI6) 3- , and the substitution rate for h-PGMs complexes with higher effective nuclear charge Z&apos; is much more slow than that of I-PGMs. and (2) for the extraction of PGMs in different configurations with oxonium (or ion -exchange) mechanism (AuCl4)-> (MCl4)2--> (MCl6)2-> (MCl6)3- and the extraction of h-PGMs complexes with low surface charge density is more fast than that of I-PGMs complexes. In view of atomic structure theory, the similarity of atomic radii and chemical properties and difficult separation of PGMs resulted from the Lanthanide Contruction between 5th period (1-PGMs) and 6th period (h-PGMs). The differences between h-PGMs and 1-PGMs are due to the loss shielding of 4f subshells on 5d electrons for h-PGMs with higher nuclear number, which makes h-PGMs have a higher Z&apos; (effective nuclear charge) and strong attraction for outer space electrons. As a result, h-PGMs metals and complexes are thermodynamically more stable and kinetically more inert than the corresponding 1-PGMs. The differences between h-PGMs and 1 -PGMs in aspects of elements properties, complexes, hydration, substitution and redox reactions , are discussed.

Jan 1, 1993

By T. P. R. de Jong

Dual energy X-ray transmission imaging is extensively applied for safety luggage inspection. Its advantages are its rapid scanning rate (25 to 100 cm/sec) at approximately I mm resolution and simultaneous thickness independent metal identification. This is especially advantageous for secondary scrap metal inspection and automatic sorting. Other applications include metal product inspection, bale control, and waste processing. Recent progress in development of an automatic on-line sorter for bulk solids is presented and discussed. Besides various non-metal applications (solid fuels, wastes etc.) it appeared particularly effective in light metal sorting. As inspection tool better control of difficult to monitor solid bulk streams, batteries, bales and other related metals becomes possible.

Jan 1, 2003