Search Documents

By Admire Chaendera

A gas jet was blown through submerged nozzles to stir the bath in the presence and absence of slag. Mixing and mass transfer rates were then studied. Water and kerosene (10% by volume) were used to simulate the metal and slag phases respectively in the cold model. The mixing time (Tmix), defined at 99.66% bath homogeneity level, increased with bath height and decreased with an increase in the gas injection rate. Its value in the model vessel was related to gas flow rate (Q), bath weight (W), and bath height (H) by, Tmix = 4.39Q-0.73W0.24H1.12. Inclusion of the slag phase increased Tmix by about 16% and the mass transfer parameter, [(Reloc,r)0.25(Ret)0.32], values by about 32%. Mass transfer rates were higher near the bath surface and in the gas-liquid plume region. They increased with gas flow rate but decreased with an increase in bath height. The relationship, K Q0.08, showing derived mass transfer coefficient (K) dependence on the gas injection rate (Q) was established. The proportionality constant in the equation varied with gas flow rate and sample location.

Jan 1, 2006

By Liping Gu, Gordon A. Irons

"A 1/3 scale ""thin-slice"" model of an electric arc furnace was developed so that gas could be injected to simulate foaming gas evolution. The influence of arc jets, oxygen lancing and bottom bubbling was also simulated. Liquid velocities were measured by a white light particle image velocimetry system. Numerical simulations of some of these effects were made using commercial CFD packages. Comparisons with measured results show that considerable care is required to select the appropriate model and to interpret the computational results.INTRODUCTIONDuring recent years electric arc furnaces (EAF) have captured a significant share of steel production, partially due to increased productivity through the introduction of advanced technology such as oxygen injection, slag foaming and long-arc operation, process automation and post-combustion. However, systematic analysis of the process and these effects on heat transfer and fluid flow in the furnace is still in its infancy. Most investigationsl1 6l have been restricted to a specific application such as oxygen lancing or bottom stirring. In addition, it is very difficult to make comparisons between these computed results and experimental/industrial results. In this work a 1/3-scale ""thin-slice"" model of Dofasco's 190 ton EAF was built. The fluid flow in the bath due to the arc jets, bottom stirring, oxygen lancing and CO evolution was simulated. The velocity distributions in the bath were measured using Particle Image Velocimetry (PIV) System. In addition, numerical simulations of bottom stirring and CO evolution were carried out using two commercial CFD packages (Fluent and Phoenics). The objective of this work is to validate the mathematical models so that they can be applied to the full-scale furnaces."

Jan 1, 1999

By Georgina De Micco

The National Commission of Atomic Energy is investigating a suitable physicochemical process for the conditioning of spent nuclear fuel and treatment of the scrap of research reactors of the Al-UxSiy type. A possible way of processing is through dry chlorination of the cladding with the purpose of selective separation of the aluminium from the remaining elements such as Fe, Ni, Zn, Cu, etc. transforming them into volatile chlorides. Some important advantages of this method are the thermal stability of the chlorides that allow the easy separation of the halides by physical methods and the low volume of radioactive waste generated. The interactions in the following systems were studied in the range of temperature between 150º-500°C: Al-Fe, Al-Ni, Al-Cu, Al-Zn, Cu-Zn and the pure metals. We found that the reactivity was different depending on if the elements were alloyed or separated. The separation factors of the systems under study were determined. Nickel is perfectly separated from aluminium for all temperatures, whereas good conditions for copper separation were achieved below 400ºC. In the case of iron, complete isolation was never attained. However, by decreasing temperature to 150ºC it is possible to obtain aluminium chloride with less iron content. The separation of zinc from the product was also difficult. It was detected that zinc chloride volatilization decreases when other chlorides were present, for example cooper chlorides. In the Cu-Zn alloy, zinc chlorides remained in the condensed product due to interactions with copper. The samples were characterized by scanning- electron microscopy (SEM), X ray diffraction (XRD) and atomic absorption.

Jan 1, 2006

By William E. Frazier

The presence of minute amounts of sulfur (10ppm) in nickel-base superalloys has been associated with reduced oxidation resistance and the premature spallation of protective coatings. Removal of sulfur by annealing these alloys in a hydrogen atmosphere has been successfully attempted by several researchers. This paper examines the fundamental thermodynamics and kinetics governing hydrogen desulfurization of elemental nickel. Limiting conditions for successful desulfurization are delineated. Assuming that the diffusion of sulfur is the rate limiting process of desulfurization, the effectiveness as well as time associated with hydrogen desulfurization is explored.

Jan 1, 1994

By Thomas Schuman, Jaan Kers, Lucas N. W. Damoah, Xiangjun Zuo, Lifeng Zhang

"Rapid technological innovation has propelled the use of electronic equipment leading to the generation of more and more waste electrical and electronic equipments (WEEE). Printed wiring board (PWB) is a component made of one or more layers of insulating material with electrical conductors. To investigate an environmentally friendly process to recycle PWBs, PWB samples with and without additives were pyrolyzed. Liquid, gas and solid products were achieved with different conversion fraction. Analysis of the exhaust gases from the experiments using GC-MS and MS showed that without CaCO3 additives poisonous gases such as C6H6 and HBr were produced which were adequately controlled if CaCO3 was added.IntroductionPyrolysis is one of the best methods for treating complex mixtures of waste polymers and to recover the material and energy content. The process consists of thermal decomposition at moderate temperatures in total absence or small amount of oxygen in which the structures of polymers break down into smaller intermediate products "". The decomposition temperature of a substance is the temperature at which the substance breaks up into smaller substances or into its constituent atoms 2). Thermal treatment of PWBs were reported using DC Arc Plasma furnace 3), and fixed bed reactor 4). One drawback in dealing with thermal treatment of PWB scraps is the likely production of super-toxic halogenated dibenzodioxins and dibenzofurans from the bromine containing structures. Pyrolysis of organic materials contained in waste PWBs leads to the formation of gases, oils, and chars which can be used as chemical feedstock or fuels ""'. Dehalogenation of the pyrolysis product of electronic scraps is essential to make it commercially acceptable. It would be obviously the most advantageous solution as pyrolysis and dehalogenation are carried out simultaneously. Reported pyrolysis investigations are at experimental stage and have been carried out in vacuum, molten salt, fluidized bed, rotary kiln, entrained, stationary, and moving bed reactors 7). Comparing to the incineration and combustion of PWBs, the pyrolysis process has several characteristics: 8'"">) 1). Converting the organic solid substance into fuel gas, fuel oil and carbon-black as storage energy; 2) Emitting toxic substances such as sulfur, bromine and heavy metals in wastes; and 3) Keeping metals from being oxidized. Although many researches into the pyrolysis of PWB wastes have been reported, most of the works have been carried out using analytical pyrolysis techniques or very small batch reactors ""~'5). Also, most of the works for the pyrolysis of PWBs haves concentrated on the composition of the organic products, particularly the brominated organics. The current study is to investigate the pyrolysis of PWB powders in a small TG-DTA scale and a 50-gram tube furnace scale."

Jan 1, 2011

By Toshia Suzuki, Keiji Kakudate, Yoshihiro Adachi

"A macro model for the steel usage pattern in Japan is proposed. The steels are classified into four types; converter steel for machinery and for construction and electric furnace (EF) steel for machinery and for construction. The steels are assumed to be discharged from the society in accordance with lifetime distributions of each usage. The amount of EF steel and the accumulation in society are calculated using a population balance model. The comparison with the calculated results and statistics ensures the validity of the model. Since the amount of EF steel for construction will increase and be oversupplied, EF steel will have to be used for machinery. The required and available amounts to supply EF steel for machinery are considered from the point of allowable· copper concentration for machinery use. Copper contaminates steel used for machinery during recycling process and contamination ratio is evaluated with the model. Copper concentration in EF steel is predicted for various scenarios.IntroductionThe amount of CO2 emission from Japanese steel industry is 48.0 million C-ton in 1990 and it occupies 15.1% of the total amount in Japan. In order to reduce the C02 emission and to save the natural resources, it is strongly required to promote the recycling of steel. However, the impurity contaminates steel in recycling process and lowers its quality. The copper concentration in EF steel is analyzed by Toi et al. using a macro model with the assumption that steel is discharged in proportion to the accumulation amount [1]. However the discharged amount of products is dependent on their age for service and usage pattern and not on the accumulation amount. In addition, the degree of copper contamination is different depending on the usage of steel. Therefore a precise model that contains the age for service within the society as a parameter and distinguishes the usage· of steel is necessary in order to clarify the problems in the recycling of steel."

Jan 1, 2000

By Ruben Alvarado

The need to increase business competitiveness while complying with environmental requirements represent the great challenge that the Caletones smelter has decided to face in a new development project with a compromising and willing alliance with its workers. To date, the project is at the feasibility stage, with start up scheduled for the middle of the year 2002. The processing capacity of the Teniente Converters will be increased to levels up to 2400 tpd of chalcopyrite-based concentrates containing 30% Cu, by means of more intensive use of oxygen and improved stabilization of the overall operation. Productivity increses in the converting of white metal and the pyrometallurgical treatment of slag are also planned. As a result of related strategies, the productivity of the supporting facilities, included the capacitiy of the sulfuric acid plants, will be increased. An intensive and well-designed labor-upgrading scheme will allow the transformation of every worker into an expert in his working areas, thus becoming an active driving force in technology development. Mechanization, appropiate infrastructure, and complete process control and instrumentation will give to the skilled and motivated personnel the necessary tools in order to attain the highest potential ever reached with the Teniente technology. The necessary investment for this project based on the adding facilities to the existing plant is only a third of that required to reach the same objective for a greenfield plant, thus yielding a very high return on investment.

Jan 1, 1999

By Julian Szekely

A review is given of the current metals processing operations, where electromagnetic forces play an important part in affecting the performance of the system. These include arc furnaces, plasmas, the Hall Cell, electromagnetic stirring and others. These considerations will be extended to discuss what new frontiers may be breached by the intelligent application of electromagnetic phenomena. The topics discussed will include magnetic flow control, levitation melting and cold crucible melting and refining.

Jan 1, 1988

By Chai Liyuan

Chromium-containing slag was detoxified by the method of microbial treatment using Ch-1bacteria isolated from nature by our research group, belonging to achromobacter sp. and with the characteristic of reducing high concentration of Cr(VI) in alkaline solution. The detoxifying process of Ch-1 to chromium-containing slag was studied by column-leaching techniques respectively. The results indicate that Cr(VI) in leachate can not be detected when chromium-containing slag has been column-leached for 7 days, and Cr(OH)3 content in precipitate is up to 32.8% with great value of resource recycling. Flowchart of engineering experimentation was ascertained based on the parameters of column-leaching experiments. Using the technique of pelletization of chromium-containing slag heap-leaching by Ch-1,the leaching rate of water-soluble Cr(VI) existing in chromium-containing slag reaches up to 100%, while the leaching rate of full chromium is up to 90%, when the process has been operated for 7-10 days under the conditions of 25-40C and consecutive spray by circular leachate. The content of Cr(VI) in chromium-containing slag after detoxified meet the national identification standard for extraction procedure inxicity for hazardous wastes(GB5085-1996) in China, moreover approximately 90% of Cr(VI) existing in chromium-containing slag has been recycled.

Jan 1, 2006

By Yousef Mohassab, Feng Chen, Hong Yong Sohn, Mohamed Elzohiery

The determination of reduction degree in a DR process is sensitive to the total iron in the ore and DRI. An accurate and high throughput analysis method for total iron has been developed. Titration of the solution after tin(II) chloride reduction of ferric ion is a widely used method for iron analysis. However, it is a multistep method that requires many chemical reagents and much time. In this work, an ICP-OES analysis method with higher or equivalent accuracy compared with the titrimetric method was developed. This method has much higher throughput and demands fewer chemical reagents compared with the titrimetric method. In this paper, a comparison of the two methods is presented.

Jan 1, 2016

By L. N. Ertzeva

The process for thermal treatment of current pyrrhotite concentrate in reducing environment with the use of disperse metal iron as an iron-bearing additive (optimal volume 20-30%), with downstream magnetic separation of the calcine, has been studied. The reduction process has been performed in conditions emulating those of both tube and fluidize-bed furnaces.

Jan 1, 2006

By Edgar Blanco

A thermodynamic and experimental investigation to develop a new process for converting molybdenite concentrate to molybdenum dioxide by a water-vapor oxidation process was carried out. In addition, the behavior of rhenium and selenium in molybdenum concentrate during the process was investigated. The kinetics of the reaction were determined by measuring the weight change of a sample with time in water vapor at temperatures between 700-1000°C. The results were analyzed by a Shrinking Unreacted Core model under chemical reaction control, which showed an activation energy value of 102 kJ/mol. To determine the behavior of rhenium and selenium, their concentrations in the molybdenum sulfide and the product molybdenum dioxide were measured by the use of ICP. While most rhenium remained with the molybdenum dioxide after the water vapor oxidation, almost all selenium volatilized. These results agree with thermodynamic analysis.

Jan 1, 2006

By Jyri Talja, Shaolong Chen, Hannu Mansikkaviita

"For optimum smelting results, proper treatment of the feed is needed to ensure favourable conditions for ignition characteristics, heat balance, mass balance with tolerable impurity levels, and overall process economics. Feed preparation consists of physical treatments before drying (blending), chemical treatments before drying, (roasting, if required), drying itself and physical treatments after drying (fractioning, if required).Effects of fluctuation on mineralogy and moisture should be minimized by blending the concentrates in a bedding plant prior to drying. As an alternative to drying, additional treatments such as roasting for impurity removal may be needed for part of the concentrate.Sustainability, energy efficiency, utilization of waste energy, low gas and dust emissions, product quality, availability and occupational exposure reduction are decisive criteria in drying today. These criteria are best met by the Kumera steam dryer, which has the best energy efficiency, zero CO2 emission, lowest operational and maintenance expenses, and superior availability and product quality.IntroductionFeed preparation plays a crucial role in having a smooth smelting operation and also the overall smelting economics in metal production. Therefore, it is of significant importance for all copper, nickel and lead smelter operations in which sulphide concentrates are fed to the primary smelting furnace. Generally speaking, the higher the metal content in the matte after primary smelting, the more important the feed preparation. This is of particular importance in the direct blister (DB) process for copper production and direct oxygen nickel (DON) for nickel production.Bedding is the first stage in feed preparation. This is very important for the sake of smoothing the mineralogical fluctuation in the feed for better smelting control. Its importance increases as the number of concentrates available for the feed mix decreases."

Jan 1, 2012

By Ashish Kumar

Comminution is an essential mineral processing operation to liberate the minerals from the ore. This however, is an energy intensive step in mineral processing industries. This work highlights the possibility of saving in grinding energy for ore comminution reducing work index of the ore by effective utilization of microwave energy. This reduced work index results in increased throughput of the grinding circuit in mineral beneficiation plant in order not to shift the product size. The fundamental principle behind this application remains the ability of microwave to heat individual phases within the ore matrix. The constituents of the ore typically having different thermal and mechanical properties develop stress of sufficient magnitude to create intergranular and transgranular fractures during heating and subsequent quenching of the ore. The experiments conducted with the ore samples of Zawar Mines and Rampura Agucha Mine of Hindustan Zinc Limited, India (A member of Vedanta Resources Plc) reflect a substantial up-shift in cumulative weight percentage passing in finer sieve fractions under quenched conditions. Further, the experiments carried out on Rampura Agucha ore reveal 20-30% reduction in work index, which result in decreased milling time or saving in grinding energy. The simulation studies estimates a 2-4% increase in plant throughput. Moreover, preliminary flotation studies indicated a significant increment in total metal recovery and concentrate grade for the desired grade and recovery values respectively. This paper is a technical note on the laboratory investigations carried out at Central Research & Development Laboratory of Hindustan Zinc Limited. Results have been encouraging to progress the work further. It is also proposed to carry out modeling work for simulation so as to predict the changes in minerals.

Jan 1, 2006

By Henrique Ventura Oliveira

Continuous casting is the most important process for solidification of steels. In this process, the fluid flow pattern in the tundish and in the mould have significant effect on the product quality. Problems associated to fluid flow in the tundish include surface turbulence, ?short-circuits?, formation of dead zones and vortexing. During grade changes, mixing in the tundish plays a significant role in determining the length of the intermixed slab. All these flow aspects can be studied by means of mathematical and physical models. In the last years, numerical simulation of fluid flow has become a very popular tool in the analysis of the performance of continuous casting tundishes. In setting-up these numerical simulations, special care should be taken in choosing the appropriate mesh distribution, the interpolation scheme, the adequate location of the inlet boundary and the turbulence model. In the present paper, turbulent fluid flow in different configurations of tundishes was simulated. Different turbulence models were used in the simulations. Residence time distribution (RTD) and mixing curves during grade changes were predicted and compared to results obtained in physical models. The performances of the different turbulence models were evaluated. For the tundishes that have been studied, the performances of the different turbulence models tested in the present work were similar. There is no evidence that any of the models provided sustained improvement when compared to the well-established standard k- model. All turbulence models tested presented limitations in simulating flows under low turbulent Reynolds numbers.

Jan 1, 2006

By Roger L. Williams

The Zinc Corporation of America Monaca smelter continues to use the St. Joe-developed electrothermic process for producing zinc metal and zinc oxide. As we enter the 1990s, the electrothermic process flexibility permits treatment of larger quantities? and lower-grade zinc-bearing recycle materials. A new sinter plant having one large sinter machine will increase sinter feed production required to meet our capacity target of 150,000 tons per year.

Jan 1, 1990

By Banqiu Wu, Ramana G. Reddy, Robin D. Rogers

Experimental studies on aluminum recycling via electrolysis in ionic liquids were carried out at the temperature of 105°C. Impure aluminum was dissolved at the anode and pure aluminum was deposited on a copper cathode. The products were characterized using an optical microscope, micro-image analyzer, X-ray diffraction, emission spectrometer, and atomic absorption analyzer. The electrorefining process with a current density of 310 - 730 AJm2, and current efficiency of about 99% was obtained. Impurities such as Si, Cu, Zn, Fe, Mg, Cr, Ni, Mn and Pb were removed as anode residue. Impure aluminum was purified from 79.8wt% to 99.9wt%. At a cell voltage of 1 volt, the energy consumption of about 3 kWh/kg-Al was obtained. The process has advantages of low energy consumption and low pollutant emissions, compared with the current industrial refining process.

Jan 1, 2000

By G. K. Ruhlandt, C. W. Kim

"A 3-D Finite Element Method program called ""SOLCAST"" has been developed to simulate the casting solidification process. Using the temperature recovery method to evaluate the latent heat of fusion and applying a new combination of the time integration scheme, SOLCAST reduces the computational time significantly compared to an existing commercial FEM program, and produces accurate results comparable to experimental casting results. Prediction of casting shrinkage porosity for A390 aluminum alloy will also be discussed. To make this FEM program useful for foundry engineers, this program was connected to a commercial pre- and post-processor.IntroductionBecause of recently increased competition, foundrymen must produce high quality castings more economically. Therefore, casting solidification analysis prior to casting production is an attractive way to reduce costs and development time.Although the actual casting solidification process is a very complicated phenomena, foundrymen could predict where shrinkage defects would occur based on a transient conduction heat transfer analysis that includes the liberation of latent heat. A numerical analysis is generally required to solve the heat diffusion equation with the latent heat diffusion term, because casting shapes are very complicated and pure materials are rarely used.Different numerical methods have been applied to the casting solidification analysis 1. Among them, a finite difference method 2 and a finite element method (FEM)3 are most commonly used.Each simulation method has one or more basic difficulties which are different for each method. These difficulties are:(1) Modeling casting shapes on a computer.(2) Time consuming computation.(3) Uncertain material properties."

Jan 1, 1986

By Hector M. Henao

In order to provide the thermochemical data regarding the slag system, which are of importance for sulfide smelting and metallurgical processes but still lacking, an experimental study was carried out on the phase relations and activity of iron oxide in the FeOX-CaO-SiO2 system at temperatures between 1300 and 1400 °C and partial pressures of oxygen between 10-9 and 10-4atm. First, the solubility of CaO and SiO2 in the solid FeO were obtained and the tie lines connecting between the solid wustite (FeO) or magnetite (Fe3O4) phase and the liquid phase were determined. Secondly, iso-activity lines for FeO in the homogeneous liquid region were determined, based on the activity of iron in the Pt-crucible used in the equilibrium experiments. The activity coefficient of FeO in this region was also derived from the composition of FeO and FeO1.5 in the liquid region. Finally, the effect of (CaO/SiO2) ratio in the system and partial pressure of oxygen on these thermochemical quantities is discussed.

Jan 1, 2006

By M. Fafard, R. Ahmed, O. Dion-Martin

"The optimization of aluminum sheet and tube forming needs the use of large strain finite elements software. The precision of the predicted results from those simulations depends mainly on the quality of constitutive law of the material used. In order to improve quality of these simulations, Barlat has suggested a new yield function named YLD2000-2d. This criterion describes the anisotropic behavior of the rolled aluminum plates. This work consists of characterizing the AA5754 alloy and estimating the material parameters needed for the YLD2000-2d criterion in LS-DYNA. In order to get these parameters, various mechanical testing were performed such as bulge and tensile tests. Moreover, the bulge test was also used to obtain an estimation of work hardening curve in large strain condition, up to 50%. The objective of this paper is to share the experimental results of the characterization of AA5754 aluminum alloy.IntroductionResearchers from National Research Council Canada's Aluminium Technology Center (NRCATC) and Aluminium Research Centre - REGAL, are working on aluminium tube hydroforming processes of AA-5754-0 alloy, used in automotive industries. Hydroforming process presents several difficulties such as wall thinning and section changes. In order to control them, some parameters can be set during the process like pressure rate and end feed level [1]. Given the complexity of the parts and the variability of the control parameters, the use of finite element method (FEA), like LS-DYNA, based on large strain theory is thus necessary. The accuracy of predicted results depends mainly on the quality of the constitutive law used to model the behavior of material. FEA results seem to be valid with the von Mises yield criterion used in some cases. But, given the anisotropic properties of the AA-5754 alloy, a more appropriate criterion could be used. The *MAT_ BARLAT YLD2000 shell material criterion, developed by Barlat [2], who's taking into account the anisotropic behaviour, was chosen due to its large flexibility and its good adaptation to particular elastoplastic behavior of aluminum. However, the use of this criterion needs to determine some material parameters by experimental way."

Jan 1, 2013