Search Documents

By Gerhard Meyer

A new instrument for the determination of iron., zinc, calcium, and other metals independently directly in the fumes emitted from steelmaking processes is described. Based on the well- accepted method of X-ray fluorescence, the instrument can detect numerous metals simultaneously in the fume as well as report their concentration on a mass per unit time basis real time to a control room computer. The instrument mounts on the wall of the fume duct and can., via a small opening, directly view the hot exhaust plum inside the duct. The concentration of metal in the fume over time has been shown to change dramatically depending on process variables. Variables such as oxygen flow rate, lance height and nozzle configuration., slag condition., and episodic scrap addition can affect the presence of metal particles and fume in the exhaust. An analysis response time of 6 seconds enables better control of the steelmaking process thereby conserving primary resources and reducing environmental impact.

Jan 1, 2001

By Chikabumi Yamauchi, Mitsuru Tanahashi, Tsuyoshi Taniguchi, Nobuo Furuta, Toshiharu Fujisawa

"It is essential to clarify the equilibrium relations among nonmetallic inclusions of the Mn0-SiO2-CrOx system and molten stainless steel in order to control non-metallic inclusions formed by the deoxidation of stainless steel with silicon. In the present study, the phase equilibria of the MnO-SiO2-CrOx system were measured by conducting the following experiments under controlled oxygen partial pressure, Po2, at 1873 K:1) Phase equilibria of the MnO-Cr20 3 binary system were measured for Po2 = 2 x 10-6 ~2 x 102 Pa.2) Phase equilibria of the MnO-SiO2-CrOx ternary system were measured for Po2 = 2 X 10-6 Pa.Based on the results, the phase diagram of this ternary system was established under the condition of the Si-deoxidation process of stainless steel (Po2 = 2 x 10-6 Pa and T = 1873 K).IntroductionAt the deoxidation stage in steelmaking process, generally multiple deoxidizers participate in deoxidation reactions, and the composition of deoxidation products ""non-metallic inclusions"" greatly varies depending on deoxidizing efoments and their contents. In order to control non-metallic inclusions formed by the refining process of steel, it is essential to clarify the equilibrium relations among non-metallic inclusions and molten steel.Especially, during the refining process of stainless steel, nonmetallic inclusions in molten steel seem to- change as follows. After the oxidation refining, Mn-chromite is formed in molten steel as non-metallic inclusion. By the deoxidation with silicon addition (mainly less than 1 mass%), Mn-chromite inclusions are changed their compositions to Mn-silicate. Segawa et al.[l] have reported the effect of amount of silicon addition on composition and mass ratio· of non-metallic inclusions during the Sideoxidation process of 18Cr-8Ni stainless steel at 1873 K, as shown in Figuri; L At higher silicon content than 0.5 mass%, only Mn-silicate was identified as non-metallic inclusion. On the other hand, at lower silicon content, both of Mn-chromite (MnO Cr2O 3) and Mn-silicate were identified. However, the thermodynamic and the kinetic analyses of the above-mentioned Sicdeoxidation process have not been made due to lack in the thermodynamic data for the non-metallic inclusions· of the MnO-SiO2-CrOx system, such as the phase diagrams, the activities of the components, and the free energy of intermediate compounds. In relation to the phase diagram of this system, those of the MnO-SiO2 [2] and the SiO2-Cr2O 3 [3] binary systems have been only reported"

Jan 1, 2000

By Jafar Safarian

A new kinetic modelling technique has been applied to study the rate of MnO reduction from slags by dissolved carbon in liquid iron. Based on a consideration of the fundamental reaction kinetics, a general differential equation for the slag reduction process has been formulated, which then is solved analytically for certain special cases. By re-writing the solutions in a dimensionless form the poorly known kinetic constants are eliminated, which makes the model both flexible and applicable to a wide range of experimental conditions. For example, changes in process parameters such as temperature, metal composition, slag composition, gas composition can readily be captured along with variations in the crucible geometry. Based on a comparison with a series of experimental reduction curves being reported in the literature, it is concluded that the predictive power of the model is surprisingly good, yielding outputs that are both reliable and physically reasonable. An attractive feature of the model is that it provides an alternative way of calculating the activation energies from experimental reductions curves. For example, it suggests that the activation energy for the reduction of MnO by dissolved carbon in liquid iron is about 90 kJ/mol, which is different from the previously reported activation energies. The model also suggests that the crucible geometry, which affects both slag the volume and the resulting slag/metal interfacial area, has a significant influence on the overall reduction kinetics. This design parameter is a key to further optimisation of the process on an industrial scale.

Jan 1, 2006

By Bradford C. Wesstrom, Omar Araujo

"Impurities from an electrolytic refinery are typically extracted from the electrolyte utilizing conventional electrowinning cells. These cells are arranged in series with cascading solution flow and are commonly referred to as liberator cells. The Freeport McMoRan Copper & Gold El Paso Refinery has optimized the removal of arsenic in cascading liberator cells by utilizing two separate feed solutions. The primary feed solution is recycled liberator electrolyte and the secondary feed solution is ""neat"" tank house electrolyte. The secondary feed solution is added based on the voltage response across the individual cells utilizing independent variable frequency drive (VFD) pumps. When the voltage across a cell changes, a signal is sent to the VFD pump to maintain a cell voltage of 1.98 volts. By maintaining this voltage the copper content in each cell exits at 2-4 grams per liter. This safely optimizes the arsenic removal as copper arsenides on the liberator cathodes.IntroductionDuring the electrolytic refining of copper, impurities from the copper anode report both to the bottom of the electrolytic refining cell as slimes and to the electrolyte. The impurities which enter the electrolyte are arsenic, antimony, bismuth and nickel. The impurities that report to the electrolyte during the electrolysis process gradually increase. As these impurities increase, they are incorporated into the refined copper cathode. There are many processes that have been used to remove these impurities from refinery electrolytes. Some of them are listed as follows: solvent extraction, ion exchange, hydrogen sulfide reduction, bioreactor, adsorption onto a low - solubility metal-oxide hydrate, adsorption onto activated carbon and EMEW cells. The conventional process used by the copper refining industry for controlling the level of impurities in electrolyte involves multistage electrolytic cascading liberator cells. In these cascading liberator cells copper, arsenic, antimony and bismuth are removed as various mixed deposits from the electrolyte. Removal of these impurities is achieved through an increase in voltage resulting from the depletion of copper in the electrolyte through electrowinning. With this higher voltage, the Group Vb elements, arsenic, antimony and bismuth are deposited on the copper cathode and report as slimes to the bottom of the cells. Nickel is removed in a subsequent process."

Jan 1, 2012

By Yahui Feng, Zhiwen Wu, Chen Chen, Xin Hong

Large amounts of copper slag containing about 40 wt% iron is generated during the process of producing copper. Recovery of iron from the copper slag is very essential not only for recycling the valuable metals and mineral resources but also for protecting the environment. The purpose of this study was to investigate the possibility of separating fayalite by oxidation-reduction process into Magnetite and silicate phases in intermediate temperature condition. Experimental results show that when the oxidation reaction at 1000℃ for 120min and the oxygen flow is 0.1L/min, most fayalite decompose to hematite, less part of magnetite and silica. And then, the mixture of carbon and oxidation product is pressed into blocks and reduced to magnetite and silica at 900℃ for 90min. A magnetic product containing about 57.9wt% iron was obtained from the magnetic separation under a magnetic field strength of 100 mT.

Jan 1, 2015

By A. Cullaj

Several industrial sites suffer from the contamination of soils from heavy metals, which are emitted among others by anthropogenic mining and metallurgical activities. Effective and economic physicochemical technologies for remediation of these sites remain complicated and costly. A new alternative remediation technique is the so-called phytoremediation. This is based on the ability of some plants to accumulate very high concentrations of metals from soils and thus providing the basis for a remediation of the contaminated sites. This technique as an emerging branch of natural biotechnology, has several advantages compared to the sophisticated physicochemical techniques of soil remediation. It is not only environmentally friendly but also its costs are quite low since it is solar driven. Furthermore plants can accumulate metals to such levels that the mineral recovery maybe feasible even in conventional Ni refinery or smelting operations. In this work, thc potential of many plants to accumulate nickel has been investigated in order to identify the species which offer the best phytoremedial potential for nickel contaminated soils in Albania. Field surveys have been made in five nickel-containing sites in order to identify the nickel tolerant species that have spontaneously grown in contaminated soils. Atomic Absorption Spectrometry measurements were carried out on 145 different plants collected. 16 of them were identified as having an hyper ability to accumulate nickel since they contained more than 10 000 mg Ni per kg (DW). Seven taxa are of Alyssum genus and one of Bornmuellera genus of Cruciferae. The highest accumulation of nickel was present in aerial parts of Alyssum murale var. chlorocarpum Hausskn (25 500 mglkg or 2.5%) and Alyssum markgrafli O.E. Schulz (23 700 mg/kg or 2.37%). The seeds germinated are more evidenced at A.m.var. chlorocarpum, about 63%. These plants are suggested as the most promising species to be used for phytoremediation purposes in nickel contaminated soils and phytoextraction of nickel.

Jan 1, 2003

By I. E. A. Aghachi

During static strain-aging of low carbon steel, when the material is pre-strained, the dislocation density increases. If totally or partially unloaded and aged for a prescribed time, interstitial solute atoms diffuse under the influence of the dislocation stress fields, thus tending to lock dislocations causing an increase in yield stress. If held for long periods at certain aging temperature, a decrease in yield stress (over-aging) is observed following the initial increase. This behaviour has been variously attributed to either recovery of cold worked dislocation structure and/or formation and coarsening of carbide precipitates. The present work demonstrates that, using a "process control" model for the competing processes of hardening and softening, dislocation recovery is responsible for over-aging of mild steel specimens under conditions tested during this investigation. Keywords: Strain-aging, Precipitation, Recovery

Jan 1, 2003

By Klaus-Markus Peters, James G. Hemrick, John Damiano

"Work was performed by Oak Ridge National Laboratory (ORNL), in collaboration with industrial refractory manufacturers, refractory users, and academic institutions, to employ novel refractory systems and techniques to reduce energy consumption of molten material processing vessels found in industries such as aluminum, glass and pulp and paper. The energy savings strategies discussed are achieved through reduction of chemical reactions, elimination of mechanical degradation caused by the service environment, reduction of temperature limitations of materials, and elimination of costly installation and repair needs. Key results of several case studies resulting from US Department of Energy (DOE) funded research programs are discussed with emphasis on applicability of these results to high temperature processing industries.IntroductionRefractory materials are limited in their application by many factors including chemical reactions between the service environment and the refractory material, mechanical degradation of the refractory material by the service environment, temperature limitations on the use of a particular refractory material, and the inability to install or repair the refractory material in a cost effective manner or while the vessel is in service. All of these limitations reduce the energy efficiency of the process as degraded refractory materials lead to loss of process heat (reduced insulation by refractories) and the need for maintenance through repair or replacement of refractory linings.This situation is conceptualized in Figure 1 which shows that when the thickness of the refractory wall is reduced by chemical or mechanical degradation, the heat losses through the wall increase exponentially. The subsequent maintenance to repair such conditions often requires cooling of the furnace or refractory lined vessel which entails loss of energy due to cooling and consumption of energy due to reheating. Additionally, production time and capability are sacrificed.Additionally, in most applications where refractories are used (metal melting furnaces, glass furnaces, steel making furnaces, gasifiers, etc.) wear of the refractory lining is not uniform. Very often, specific areas will wear (become thinner) more rapidly due to exposure to more corrosive or erosive conditions. This concept is illustrated in Figure 2, through the example of excessive metal line corrosion."

Jan 1, 2009

By C. F. Ferron

A process has been developed to treat the copper gold ores from the Guelb Moghrein mine in Mauritania. The process consists of pressure leaching the sulphide concentrate, neutralising with the oxide ore, recovery of copper by SX/EW and of gold by cyanidation of the autoclave residue. This paper focuses on the pressure leaching step, and presents data from bench and pilot plant test programs. In particular, attention is drawn to the effects of temperature, grind size, neutralisation, retention time and solution recycle on the kinetics of copper dissolution from various flotation concentrates. Likely leach mechanisms are briefly discussed.

Jan 1, 2000

By Ruirui Wei, Yanhui Liu, Fangqing Yin, Meilong Hu

In China, Basic Oxygen Furnace (BOF) slag is traditionally used as an aggregate for civil engineering, for road engineering and fertilizer. In order to make full use of BOF slag, the experiments of BOF slag with high temperature roasting has been carried out and the phase transformation is studied. The BOF slag from Chongqing Iron & Steel is roasted in the electric muffle furnace at three different temperature. The influences of the high temperature roasting on change the phase composition of BOF slag was characterized by XRD. The results revealed that SFCA was produced at the high temperature in air atmosphere and melting temperature of slag was lowered. Therefore, if the BOF slag which treated by roasting was utilized in the sintering process, it is advantageous to improve the sintering strength and the formation of the liquid phase and reduce fuel consumption in the sintering production process.

Jan 1, 2015

By George Grandy

Kvaerner experience is being used to develop software to design or simulate crushing and screening plants. The model techniques discussed are presently being used for open-circuit plants and are being extended to closed circuit plants. The program contains a library of routines, each representing a piece of equipment or unit operation, which are assembled into one of several open-circuit plant configurations. Routines include gyratory primary crushers; standard secondary and shorthead tertiary cone crushers; single, double or triple deck screens; and stockpiles, feed bins and belt conveyors. The program uses steady-state models to simulate the performance of crushers and screens that have small residence times and quickly reach equilibrium when operating conditions and/or parameters are changed. The dynamic aspect of the total circuit model concerns the storage units within the circuit, i.e. stockpiles and bins, and, in the closed circuit configuration, circulating loads and size distributions. In many cases, just vendor's catalog data are necessary for a pre-feasibility simulation; in other cases, actual plant test data are required to obtain more accurate simulations. The entire plant is shown in a single graphic screen so the user can see all the relevant information he might want, and soft-keys are provided for the user to make on- line parameter changes and observe the effects on storage elements, equipment feed rates and the final product size distributions. The model also reports equipment utilization in percentage, power consumption, and other related operating information, and soon, will be able to report estimated capital and operating costs.

Jan 1, 1999

By M. A. Halim, V. I. Lakshmanan, T. Sheikhzeinoddin, R. Roy

"Chloride metallurgy is emerging as an alternative process for the production of base metals. Process Research ORTECH Inc. (PRO) has been at the forefront of technological development of chloride metallurgy. PRO has developed an innovative technology for the production of high purity titanium dioxide, iron oxide and vanadium pentoxide from ilmenite ores and concentrates. PRO is also developing its proprietary mixed chloride technology for the extraction of vanadium from other sources such as oil shales. In this paper, results from the test work conducted at PRO for the extraction of Ti and V using a mixed chloride lixiviant are presented.IntroductionTitanium and vanadium alloys and compounds have numerous industrial applications. Titanium dioxide is used in paints, plastics, rubber, paper, inks, textiles and a number of other miscellaneous applications. Currently nanosize T1O2 is being investigated for application in the cosmetics industry. Inorganic sunscreens mainly use T1O2 or ZnO particles, which reflect and scatter ultra-violet light. T1O2 nanomaterial is also finding application in smart construction materials and coatings, as a photo-catalytic converter. Nano TiO2 can catalyze the dissociation of NOX gases and other automotive emissions, thereby reducing the smog in urban centers. After the construction material is exposed to sunlight or ultra-violet light, the T1O2 is photo-activated and degrades the pollutants.Titanium metal and titanium dioxide are produced from ilmenite (FeTiOs) or rutile (naturally occurring T1O2) ore. Only about 6% of the titanium resources are used to produce titanium metal and the rest is used to produce T1O2. Many of the titanium ore deposits currently have unacceptable levels of transition metals which limits their processing by conventional routes."

Jan 1, 2012

By Oleg I. Platonov

Method of high-temperature reduction of oxygen-bearing sulfurous gas has been developed at Copper Plant (CP) of MMC ?Norilsk Nickel? Trans-Polar Division (PD) with the aim of producing elemental sulfur from Vanyukov furnace? off-gas. Non-explosive reduction technology of oxygen-bearing sulfurous gas by methane utilized at Copper Plant has been designed to separate the processes of gas heating and sulfur dioxide reduction based on different kinetic of the reactions oxygen fixing and SO2 reduction. First, natural gas promptly reacts with oxygen contained in the process gas to heat a gas mixture up to the temperature of sulfur dioxide reduction (1200C). Then isothermal reduction takes place within 1 sec. Combustion chamber (pre-chamber) design developed based on the above principles is presented. Practical experience of the two reduction reactors operation at CP since 1996 proves high efficiency of the developed reduction process. The volume efficiency rises dramatically thanks to the fact that both fuel and reducing agent are fed into the reactor volume in the form of high-speed turbulent jets providing an intensive mixing of the reacting gases. On condition of equal internal volume of the reactors, the developed process offers higher efficiency of reagent interaction resulting in sulfur conversion exceeding 90%, as compared to the equilibrium one.

Jan 1, 2006

By Kazuki Morita, Ye Wang

In order to optimize the B removal during slag-refining process for solar-grade silicon production, a new process for the removal of B in molten Si was proposed based on the principle of oxidized chlorination and evaporation. B can be generated and evaporated in the form of B-containing gas (BOCl) from molten Si using CaO–SiO2–CaCl2 slag system. Compared with the binary systems of CaO–CaCl2 and SiO2–CaCl2 slag, the ternary slag system CaO–SiO2–CaCl2 showed a better potential (90 pct) for B removal at 1723 K for 2 h. Moreover, the diffusion coefficient (D) of B in the slag was also determined using tube-molten pool method. Through this, it was found that the rate-limiting step of B-removal in the slag refining process is controlled by B transfer in the slag interface and surface.

Mar 1, 2017

By Larry M. Southwick

The smelting of copper and other non-ferrous metals have made considerable advances over the last 125 years. Many of the ideas and processes currently in use were attempted early in the history of smelting and were unsuccessful. Often the cause was incomplete understanding of the metallurgy involved, inadequate refractories, poor materials of equipment fabrication or trying too many new ideas at once. With time, these problems get solved and the technologies become commercialized .These were processes whose time had not come when originally proposed, but did eventually. On the other hand, there have been some concepts whose time will never come. They were impossible then and they are impossible now. The people that dream these up were either crackpots (they didn't know what they were doing, but thought they did), or charlatans (they knew they didn't know what they were doing, but didn't care). Both rely on bad science to propose metallurgical absurdities. These too have their place in the development of technology, though mostly negative, and several examples will be discussed in this paper. Three from around the turn of the century will be covered, as well as one from this decade. The last demonstrates that the art of creating absurdities has not withered, even after ninety years of scientific sophistication, and some can even be patented. The first three reached field trials due to the gullibility of company management. The last arose from a fortuitous mis-operation of a plant which solved a problem, but the explanation and patent which arose are metallurgically impossible.

Jan 1, 1999

By Kamal Adham

Hydrochloric acid is used as lixiviant in such hydrometallurgy processes as synthetic rutile production and nickel extraction. The intermediary metal chloride is normally roasted to release gaseous HCl and a solid metal oxide. A large amount of fuel is required for this thermal regeneration, mainly to vaporize the water content of the feed solution. To conserve fuel, some energy recovery from the off-gas is currently achieved, but the fuel costs can further be reduced by process optimization and energy recovery from the gaseous, aqueous and solid products of the regenerator. Here, first the existing limitations to fuel efficiency in the industrial scale HCl regeneration roasters are described. Then, for the case of a dilute feed solution, options for pre-evaporation and fuel minimization are modeled and compared. Finally, energy recovery technologies including heat pumps, acid heat exchangers and solid waste heat boilers are described, and their potentials as the heat source for pre-evaporation of the feed are evaluated.

Jan 1, 2003

By Anne C. Chinellato, Alejandra T. Soria, Nelida L. del Mastro, Amanda C. S. Pereiral, Esperidiana A. B. Moura, Anibal V. Abreu

"This work presents a comparative study of the thermo-mechanical and morphological properties of sugarcane bagasse fiber/HDPE composite treated with electron-beam and gamma radiation. The composite samples obtained by extrusion and injection molding processes were irradiated at 50 and 90 kGy using either a 1.5 MeV electron beam accelerator or gamma irradiator EMI-9, at room temperature in presence of air. The irradiated and non-irradiated samples were submitted to mechanical and MPI tests, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), sol-gel analysis and X-Rays Diffraction (XRD) and the correlation between their properties was discussed. Improvement of the bagasse fiber/HDPE composite properties, using electron-beam or gamma radiation, was found.IntroductionResidues of sugarcane bagasse fiber are widely produced in Latin America and other countries: in Southern Africa, Egypt, South-Eastern Asia, India, China, Australia, Cuba, among other producers, as by-products of the sugar and bioethanol industry. The sugarcane industry in Brazil and Uruguay is well established and expanding with large potential to increase the production of sugarcane bagasse in the next years [1-3]. Although the major portion of the bagasse is currently burnt for energy supply in the sugarcane industry, the disposal of this byproduct is still inefficient and, consequently, it is critical for agricu1ture profitability and environmental protection. Sugarcane bagasse is a lignocellu1ose fiber mainly constituted by around 46 % cellu1ose, containing hemicellu1ose, lignin, fat and waxes, silica and other elements [3, 4]. Studies have reported that sugarcane bagasse can be used to produce thermoplastic polymeric composites with excellent properties for many applications. [5-8]. Based on this survey, the transformation of bagasse into high quality industrial products, such as bagasse-polymer composites, can provide its more effective utilization."

Jan 1, 2012

By Kezhuan Gu

Data on the kinetics and thermodynamics of dephosphorization are analyzed in terms of the dynamic partition ratio, determined by a combination of slag thermodynamic properties and the balance of oxygen supply and consumption. A recently developed phosphate capacity correlation is combined with data on kinetics to quantify the most significant parameters in controlling the interfacial oxygen potential. The role of slag composition, entrained gas fraction and temperature are discussed in addition to metal carbon and sulfur content. It is demonstrated that the mass transport of oxygen in the slag is enhanced by factors increasing conductivity and inhibited by entrained gas. The mass transfer of phosphorus in the metal is described considering surface renewal induced by CO bubbles.

By Patrick Clark

As part of the Mine Waste Technology Program (MWTP), a large-scale column test using bacteria and a sulfide ore was conducted at McClelland Laboratories, Inc., in Sparks, Nevada. Four technology providers participated in this demonstration. A mining company in Nevada provided the sulfide ore, process effluent and make-up water. A process effluent column, a chemical oxidation column, and the four biological treatment columns were set side by side on a test pad outside the laboratory building. The process effluent and chemical oxidation columns were used for experimental control. The goal of this project was to evaluate the viability and feasibility of using these biodegradation technologies to reduce the cyanide to the regulatory level of 0.2 parts per million (ppm) within an acceptable timeframe and with low operational costs. The column testing began on December 3, 1998 and operated until May 17, 1999. One technology provider reached the regulatory level within the 158 days. The remaining three biotechnology columns were approaching the regulatory limit at completion of the demonstration. The MWTP is funded by the U.S. Environmental Protection Agency (EPA) and is jointly administered through an interagency agreement with the U.S. Department of Energy (DOE).

Jan 1, 1998

By Adolfo Pillihuaman, Alberto Nogueira, Cyro Takano, Marcelo Mourão

The organic household waste has a growing disposal problem, requiring costly disposal systems. It is necessary to find new applications for these materials; one could be the steelmaking raw material production. In this paper is studied the development of self-reducing pellets from the organic waste pyrolysis, where is generated carbon and condensable and non-condensable volatiles. Non-condensable volatiles were burned and condensable volatiles were recovered. The resulting tar was mixed with iron ore, coal powder and flux (CaO), to then be pelletized together. Compression, falls and tumbler tests were conducted to characterize the pellets before and after heat treatment and reduction processes. The reduction curve and their physical and morphological characterization were measured. The results were as was expected, the fluidized coal create sufficient adhesion that pellets earned resistance with an equivalent resistance of common pellets, showing a good feasibility of this process.

Jan 1, 2015