Search Documents

By Chu Yong Cheng

The solvent extraction (SX) processes of the three pressure acid leach (PAL) nickel plants in Western Australia have been reviewed. The use of intermediate precipitation, solids/liquid separation and re-leach in the three W A nickel plants make these processes complicated and costly in capital and ?operation. The research work carried out by the SX group at the AJ Parker Cooperative Research Centre for Hydrometallurgy I CSIRO Minerals has led to the development of direct solvent extraction (DSX) processes to recover and purify nickel and cobalt from leach solutions. The simplicity of the process flowsheets and the expected savings in capital and operating costs are the major advantages of the new DSX processes over the reviewed processes. By using a new synergistic organic system in semi-continuous tests with a pilot plant leach solution (after iron precipitation) from BHP-BiIliton Stainless Steel Materials, the metal values (Ni and Co) together with zinc and copper were separated from the major impurities (Mn, Mg and Ca, together with Cl) in the first SX circuit. The co-extracted manganese, magnesium and' calcium were easily scrubbed out. After stripping, the metal values (Ni and Co) together with zinc and copper were concentrated, resulting in a much smaller second SX circuit and equipment in the down stream processes. The extraction and stripping kinetics of the metals with the new synergistic organic solution were very fast. The extraction and stripping almost reached steady state within 0.5 minutes. Semi-continuous test work with a synthetic leach solution, a cobalt pilot plant leach solution from Peko Rehabilitation Project Pty Ltd and a synthetic solution to simulate a concentrated laterite leach solution from BHP-Billiton Stainless Steel Materials showed that manganese, calcium, copper and zinc can be effectively and efficiently separated from nickel, cobalt and magnesium by extraction, scrubbing and stripping. This led to the development of another DSX process using D2EHPA to recover nickel and cobalt from leach solutions.

Jan 1, 2003

By Yunhua Gan, Xiaowen Chen, Meilong Hu, Haige Li, Yang Tong

Ethanol is a kind of renewable fuel, which can be produced from biomass and applied in many energy areas, such as motorcar. The combustion of ethanol in meso-scale is facing great challenges, such as great heat loss, poor stability, and low combustion efficiency. Electro-spraying technique is an effective method to atomize liquid ethanol due to its great advantage of monodisperse and uniform characteristics. In present study, electro-spraying was applied in liquid meso-scale combustor to produce very small droplet diameter and uniform droplet distribution. Experiments were carried out based on nozzle-ring-mesh electrode structure using pure liquid ethanol as fuel. Electro-spraying characteristics were measured by Phase Doppler Anemometer (PDA) under different nozzle voltages, ring electrode voltages, flow rates, and steel mesh positions. The results may be helpful to the design of new meso-scale electro-spraying combustor using renewable liquid fuel.

Mar 1, 2017

By Batric Pesic

Calcium silicate slag (Di-Cal) and magnesium oxide condensate (MgO) are the by-products of magnesium smelting operations, As these oxides have acid neutralizing and metal precipitating properties, it was decided to examine their reactions with (a) individual heavy metals and (b) with a mixture of metals in solution, The resulting solid reaction products were further tested with respect to the stability of the contained metals, The stability of the solid precipitates were examined as a function of the method of precipitation and as function of the solution pH With respect to the method of precipitation, the performance of Di-Cal and MgO was compared to the performance of lime, an industry standard for heavy metal precipitation, Four different pH solutions (4,0, 5,0, 7,0 and 1 LO) were used to study the effect of pH on the stability of the precipitates. It was found that Di-Cal, in most cases, produced the most stable precipitates and thus, outperformed lime, Metal precipitates prepared by the addition of MgO were the most soluble for each metal studied, except for Se,

Jan 1, 2001

By Y. F. Jia

Arsenic constitutes a major contaminant for the hydrometallurgical industry. Its removal and immobilization from process effluents typically involves lime neutralization and co-precipitation with ferric iron (Fe (III)/As(V)>3). Alternatively, precipitation of scorodite (FeAsO4?2H2O (cr)) may be applied to arsenic fixation. The mechanism of arsenic fixation in the former process has been suggested to be surface adsorption. Unequivocal characterization of these products is difficult because of their amorphous nature hence a variety of methods need to be applied including the particularly powerful method, extended x-ray absorption fine structure (EXAFS) spectroscopy. In this study, we have investigated the preparation of arsenate-adsorbed ferrihydrite with the purpose to compare its structure to that of Fe(III)-As(V) co-precipitates and scorodite (both amorphous and crystalline). Furthermore the solubilities of these Fe(III)-As(V) solids are measured as a function of pH. Their structures are elucidated and correlated to their solubilities and thereby the application of these findings to the practice of arsenic removal and disposal is assessed.

Jan 1, 2003

By Mahmood Alemrajabi

When LKAB processes their iron ores in northern Sweden, they generate apatite as a by-product. The apatite has been recovered by flotation and the concentrate contains about 0.4 wt% rare earth elements (REE). Both phosphate rock and REE are listed as critical raw materials for the European union. In the present study, the recovery of REE within the nitrophosphate process of fertilizer production has been studied. In the first stage, the REE are precipitated and isolated as a phosphate concentrate. For further purification and individual separation of REE by solvent extraction, removal of phosphorous from the concentrate to enhance the dissolution of REE in mild acidic solutions is essential. In this study, thermal treatment of the concentrate with sodium hydroxide at elevated temperatures followed by water leaching has been studied in order to separate the phosphorous and thereby facilitate dissolution of the REE. The results show that 95% of total phosphorous initially present in the REE phosphate concentrate is removed after thermal treatment with NaOH 1:1 mass ratio, at 400 °C.

By Viktor Ashikhin, Pavel Arkhipov, Yurii Zaikov

"Lead alloys electro-winning from chloride melts was under investigation. Impurities concentration in cathode lead is strongly depended on temperature, electrolyte composition, anode current density. The equilibrium electrode potentials of lead-antimony alloys with the various content of electropositive metal in the alloy were investigated in the wide temperature interval. Thermodynamic properties of Pb-Sb alloys containing 20-95 mol% of Pb were studied by EMF method in temperature interval 723-873K in molten mixture of potassium and lead chlorides. Partial and integral thermodynamic characteristics were calculated. Small negative deviations from Raul’s law were found. Anode processes were investigated. The lead dissolution was found to be the only process in certain interval of current densities and electropositive metal content in alloy.IntroductionAt present human race is facing the problem of pollution by lead and its compounds and also the pollution influence on population health all over the world. One of the solution ways is the recycling lead containing technical wastes by ecologically clean technologies.World scientific community pays much attention to the electrolysis of molten salts. The usage of salt mixtures, as electrolytes, discovers new possibilities in the production of metals, metal compounds and alloys. ?????????? of the electrolysis at the temperature 50 - 200 °? above the melting temperature of chosen salt mixture allow to unbreaks processes, that undergo in the pre-electrode layer. The rate of the electrodepositing of elements are much higher than in the water electrolytes. At present there are technologies developed for production of metals (Ta, Nb, Ti, Zr, Hf, Ca, Al, Mg, Be, Li and others) by the electrolysis of the melts. Electrolysis of melts might be used in order to convert different technological formations containing lead and other nonferrous metals, that produced by different enterprises. According to the level of the influence on the living organisms lead is in the group of highly dangerous substances alongside with arsenic, cadmium, mercury, selenium, zinc, etc. Toxity and ability to accumulate in the human organism are two main sources of danger for the human being."

Jan 1, 2008

By Lennart Hedlund

There is today a long and well-documented experience of the use of Boliden "Kaldo' technology for treatment of various feed matedals. The process is In commercial' operation in the Boliden Mineral's Rönnskär plant In Sweden for treatment of copper scraps and lead concentrates (In campaigns). This plant was built In 1976 for treatment of lead dusts from the copper plant but later modified to take other raw materials. Boliden's Kaldo techr:lology Is also In operation since 1991 for treatment of low-grade copper scraps In Enlrlsorse's plant In Porto Marghera (Venice), Italy. The plant is producing 25 000 tons of blister copper ,per year. The Kaldo furnace Isa high :Intensity smelting unit, where several successive treatment steps can be done In the same vessel. The furnace can be totally enclosed to protect the working environment, and the small off-gas volume can easily be dedusted. Input materials can vary over a very wide range, the products will be a dump slag with low (0,5%) copper and lead contents and black copper or blister copper. The dust from the process can be used for zinc production. A new development is autogenous smelting of scrap in a Pierce-Smith converter, implemented at Compagnie Générale d' Èlectrolyse du Palais in France.

Jan 1, 1995

By Vadym Drozd, Yongzhou Sun, Shah Najiba, Jiuhua Chen, Andriy Durygin

"Phase transitions of the potential hydrogen storage compound, ammonia borane (NH3.BH3), was investigated using Raman spectroscopy and a diamond anvil cell at high pressures up to 9.5 GPa and low temperatures down to 90K. At room temperature, ammonia borane has three phase transitions in this pressure range. Upon cooling, four new phases were discovered through changes in characteristic Raman spectra. This result provides information about the stability of new bonding characteristics of this potential hydrogen storage material at low temperature and high pressure region.IntroductionDevelopment of hydrogen technology requires the safe, efficient and environmental friendly materials for hydrogen storage and hydrides have attracted much attention as hydrogen storage media. Among chemical hydrides, ammonia borane (BH3NH3) stands out due to its high gravimetric and volumetric hydrogen density ' "". Despite high hydrogen content, this compound is very stable. It releases hydrogen in several steps by thermal decomposition in the temperature range of 100°C to 500°C. Direct thermal decomposition also causes toxic borazine emission. Recent research interests on ammonia borane include destabilizing this compound to lower the dehydrogenation temperature with an enhanced hydrogen release rate using different techniques, e.g. the nanoscaffolds'', ionic liquids"" and acid'"" or transition metal catalysts' ""'. As a molecule of ammonia borane consists of protonic (NH) and hydritic (BH) hydrogens bonded by the polarized dative bond, thermal or catalyzed decomposition requires breaking of N-H and B-H bonding. Still now, the detailed information about the bonding characteristics of ammonia borane is not sufficient to understand details about its phases and structures. The development of methods to enhance hydrogen discharge rate from ammonia borane requires a detailed study about the structural and dynamical properties that control the stability and the intermolecular interactions of this material. This study is motivated to investigate the stability of the existing phases and also to explore the existence of any new phases at different temperatures and pressures which may have enhanced hydrogen release and uptake properties."

Jan 1, 2012

By Alejandro R. Alonso, Lizet Alvarado, Gretchen T. Lapidus

"Cobalt and lithium recovery from spent Li-ion secondary batteries has been increasingly studied in recent years due to the high value of both metals and the low proven reserves for lithium. The standard method employed until now has been the deactivation and crushing of the batteries, followed by leaching of the L1C0O2 spinel from the battery cathode using acid solutions, such as 1.5 to 2.0 M HC1 or H2SO4, in a temperature range from 120°C to 250°C. Once leached, the cobalt is separated by electrodeposition and the lithium by precipitation, using large amounts of carbonate to bring the solution to alkaline pH values. In the present work, citric-thiosulfate solutions are used for the spinel leach at room temperature, favoring a reductive environment at room temperature, which stabilizes the cobalt(II) as cobalt citrate and lithium(I) at pH 5, and recovers approximately 99% of both metals.IntroductionThe Li-ion batteries industry has become an important economic sector in recent years. This type of battery is the most promising system for energy storage, because of its high efficiency in charge-discharge cycles, and its adaptability to many configurations. The demand will probably increase because of the need for mobile energy sources in many types of devices ranging from cell phones, tablets, and laptops to medical, navigation and sophisticated communication equipment and even in automobiles.One major problem related to the use of these batteries is the method employed for recycling the components, mostly cobalt and lithium. Currently, there are two processes employed on an industrial scale: the Sony/Sumimoto process, used since 1990 [1] and the Toxco Process [2]. In the first case, incineration is used to open the batteries and at same time volatilize the organic solvents. After that, the metals (copper, iron and aluminum) are physically separated. The cobalt and lithium are recovered as oxides and then thermally treated in order to recycle them for new batteries manufacture."

Jan 1, 2012

By R. T. Hernández, I. Hilerio, A. Altamirano, M. A. Barrón

"The principal objective for finishing surfaces is to protect and/or to decorate them. This can be achieved by adding or removing material from the work surface. The addition of aggregated material is called coating or recovering. In this work, mecano-chemical techniques are investigated for surface finishing. For these techniques, barreling or polishing by the friction method will be used. These are the cleaning or finishing processes most used for great volumes of small pieces. These methods improve the surface finishing by eliminating burrs, sharp pointed, tool marks and crusts of casting. They are used to clean metallic pieces, ceramics and polymeric materials. The process is based on rubbing or friction by abrasives. The pieces are arranged in the barrel with an abrasive and an additive (water or chemical additive). The machine produces a rotating movement on the pieces. When the abrasive passes against the surfaces of the pieces, it produces an action of rubbing and impact that cleans the surfaces. The rubbing action is developed when the upper layer of the charge slides to the lower extreme when the barrel rotates. The barrel can be hexagonal or octagonal to facilitate the sliding of the charge. The barrels can be between 15 to 120 cm in length and they can have almost any diameter and velocity of rotation. There are several types of barrel: individual, multiples, and multiple compartments. The barrels are rotated using a wheel spindle or rolling pins, that the can ride horizontally or be tilted to produce an additional movement of the charge.IntroductionShot penning is a cold method in which compressive effects are induced on an exposed surface of a metallic piece, by the impact of a rain of shots directly on the surface of the metal, at great speed under controlled conditions. This differs from cleaning with the help of air, because even when shot penning cleans the surface of the metal, this function is incidental. The main purpose of shot penning is to increase the resistance of the piece to fatigue. The process has other applications: raises the tensile strength and decrease corrosion fracture."

Jan 1, 2012

By Roberto Giovanardi, Isabella Lancellotti, Luisa Barbieri, Ercole Soragni, Fernanda Andreola

"Recovery of precious metals (PMs) is a present topic, as they are used almost in every electronicelectric device. Gold is the second PM in order of consumption (following silver) and it is almost ubiquitary in electronics where it mainly finds application to produce bonding wires in integrated circuits and as a coating for contacts and connectors. Given this, discontinued electronic and, with a minor role, electric devices may represent a primary source of PMs as gold mines or jewelery wastes.At present the recovery of gold from such waste is generally accomplished by two strategies: by oxidative thermal treatment followed by metallurgical or chemical processes or by cyanide chemical etching; both techniques do not represent the optimum as the first one deserves a great amount of energy and non-combustible pollutant slag and fumes are produced, while the second procedure comports the use of a highly pollutant agent as cyanide.The aim of this work is the characterization of different electronics scraps to evaluate the gold concentration, and the selective recovery of this metal using enviromentally-friendly techniques. In particular, a new process was developed in order to overcome such environmental and efficiency issues. The process reaches the goal of detach the gold film from the substrate by selective leaching of the supporting metal.IntroductionThe treatment of waste from electrical and electronic equipments is a current topic as their role in modern life is increasing. The disposal of such waste represents both an environmental and an economical concern due to the vast amount of both precious and non precious metals.The use of precious metals (PM) in this field is of primary importance given PM’s unique properties, which give to each of them a specific and irreplaceable role. Silver is the most used, with a demand of over 5000 tonnes per year, mainly for switches and contacts in electric appliances. Gold is the second PM in order of consumption (over 250 tonnes per year and 8% of the total demand) and it is almost ubiquitous in electronics where it finds application to produce bonding wires in integrated circuits and as a coating for contacts and connectors. It is also used as solder in integrated circuits (in alloy with tin) or for wide coatings where it ensures protection against corrosion. Palladium, platinum, rhodium and iridium follow in order of consumption [1- 3]."

Jan 1, 2008

By O. Chemezov, Yu Zaikov, A. Apisarov, A. Isakov

"Silicon deposits containing 99,9 wt.% of main component were obtained by SiO2 electrolysis from chloride-fluoride melts. The operating temperature was varied from 973 up to 1073 K. The conditions for obtaining crystalline fibrous micro- or nanodeposits were determined. The deposits were investigated by ESM methodIntroductionThere are large reserves of natural quartz of high purity in Russia. Processing of this raw material by electrolysis in molten salts produces silicon containing 99.9 weight percent of basic substance.[1]This method is less energy-consuming in comparison to existing methods for producing high purity silicon from gas phase.Another advantage of the electrolytic method for producing silicon from its oxide in molten salts is the possibility of production of high-purity silicon under air atmosphere. It dramatically reduces costs of the electrolytic cell construction, and the operating costs at electrolysis.On our opinion, the main advantage of the electrolytic production from SiO2 in molten salts is a unique opportunity to obtain micro-and nanostructures of silicon deposits. In particular, it is possible to obtain fibrous structures of silicon. The electrolytic method allows smoothly adjusting the thickness and length of silicon micro- and nano-wires by varying the cathode current density and temperature of the process."

Jan 1, 2012

By Maria Cristina Ruiz

The removal of iron from the leaching circuits is a common problem in the hydrometallurgical processing of non ferrous metals. Among the currently available processes, hematite precipitation is the most recommendable from an environmental point of view. This paper is concerned with the batch precipitation of hematite from ferrous sulfate solutions. One of the main objectives of the study was to determine the effect of the experimental conditions on the extent of iron precipitation as well as the purity and the particle size distribution of the precipitates. The main variables studied were temperature (180 to 220 ºC), concentration of sulfuric acid (1 to 10 gpl), initial iron concentration (1 to 15 gpl) and partial pressure of oxygen (3 to 7 atm). The results showed that increasing the oxygen partial pressure from 3 to 7 atm produced a very small increase on the rate of hematite precipitation indicating that a large partial pressure of oxygen is not needed for an effective ferrous to ferric oxidation. An increase in the temperature produced finer precipitates with lower sulfur contents. On the other hand, an increase in sulfuric acid concentration and initial iron concentration produced precipitates with larger particle sizes and higher sulfur contents.

Jan 1, 2006

By I. Barin, G. Eriksson, F. Sauert

Computer-aided calculations using data bases and program systems are more and more needed for the rational development and optirnization of high-temperature processes. The calculation of mass and energy fluxes between different process steps as well as the determination of the chemical equilibria will be discussed, giving examples from nonferrous metallurgy. The simulation of a waste-material treatment process including high-temperature combustion and gas-cleaning systems will also be demonstrated.

Jan 1, 1988

By Kaixi Jiang, Lei Zhang, Sanping Liu, Yufang Wang, Xiaoping Zou

"Molybdenite concentrates are usually treated by roasting, but low concentration SO2 pollution is a problem. Extraction of molybdenum and rhenium from molybdenite concentrates with a pressure oxidative leaching (POX) and solvent extraction (SX) process was studied. A series of POX-SX laboratory and pilot tests were carried out on the molybdenite concentrate. In the POX stage, more than 95% rhenium and 15-20% molybdenum were leached into solution. Solvent extraction recovered the rhenium and molybdenum from the POX solution. The extraction rates of Re and Mo were above 98%. The loaded organic reagent is stripped with ammonia. The stripping ratio of Mo is more than 98%. Compared to the roasting process, the total recovery of Mo increased from 93% to 97%, and Re from 60% to 90%. In the coming five years, POX-SX technology will be competitive in China.IntroductionMolybdenite is the main resource for the production of molybdenum, and about 99% of the total molybdenum was extracted from molybdenite. Rhenium is one of the important new materials in national defense, space flights, nuclear energy and electronics, because of its high melting point, high strength, plastic properties and significant creep resistance. There are no single rhenium ores in the world; rhenium mainly co-exists with molybdenum. Consequently, molybdenite is also the main resource for the extraction of rhenium."

Jan 1, 2012

By Yuya Nakai, Kuniaki Murase, Kazuhiro Fukami, Atsushi Kitada, Ken Adachi

The resources of vanadium –titanium magnetite in China are very abundant, most of which are used to prepare titanium-rich materials. Titanium pigment, electric welding bar and titanium sponge are made from titanium-rich materials such as synthetic rutile and titanium slag etc. To fully utilize titanium resources, many production methods of titanium-rich materials were proposed. In this article, authors review on methods of preparing titanium-rich materials which are Electric Smelting Process, Reduction-rust Process, Selective Chlorination Process, Acid Leaching Process, and sum the advantages and disadvantages of them. Existing problems and possible tendency of production methods of titanium-rich materials are also discussed.

Mar 1, 2018

By L. N. Ertzeva

The present work is dedicated to investigation of the sulfidizing process of ore pyrrhotite concentrate with recovery of a sulfide material, enriched with non-ferrous metals, and waste pyrite, with downstream separation by a certain beneficiation method.

Jan 1, 2006

By Y. C. Avniel, T. E. Warner

"It is important to be able to measure sulphur and nitrogen in molten iron and steel on-line. Unfortunately, there are no solid electrolytes which are stable under oxidising conditions and in which the ions of these species are mobile. In this paper, novel applications of beta alumina electrolytes are described and the results compared with data in the literature. Excellent agreement was obtained confirming this approach as a viable method of detecting elements whose ions are not mobile in solid electrolytes.IntroductionIn the past two decades, the rate of many processes in steelmaking have increased substantially. The sophistication of chemical analysis has also increased but analytical equipment is frequently positioned a significant distance from the operating plant which dictates that time is spent taking a sample, sending it to the analytical facility, preparation of the analytical sample prior to insertion into the equipment. In many cases, the time taken for analysis can exceed the time taken for the actual process and is now the rate defining step. Furthermore, most analytical methods are unable to distinguish between the amount of element which is dissolved in the steel and that contained in precipitates. Even if the analytical equipment could separate these two, the distribution would have changed between the molten steel and the cast sample. It would be an advantage to analyse on-line for impurities in molten metals."

Jan 1, 1997

By A. C. Wadhawan

In the present context of rapid industrialization, production of Lead-Zinc metals from low grade materials, residues and wastes can make substantial contribution to the supply of these metals in India. Recovery from secondary sources also plays an important role in conservation of mineral resources and lower power consumption. Conscious effort is therefore, required to increase the secondary metals which, besides saving in energy cost will also help in waste material management and keeping environment clean. The major thrust is, therefore, needed in this direction. During all these years, the Indian Lead- Zinc industry has made sustained efforts for recovery of metals from low grade ores and from metallurgical wastes and residues. The paper identifies the treatment of low grade ores by various technologies and techniques and the treatment of metallurgical residues and wastes generated during primary Lead and Zinc smelting in India. Some of the major achievements in past decade have also been elaborated in the paper. The strategies to be followed for continuing treatment of low grade ores and waste materials by adopting newer, environmental friendly technologies, in consonance with the rigid standards being adopted by most of the countries including India. have also been dealt with in the paper.

Jan 1, 1994

By Saskia Duyvesteyn

Small ion-exchange resin particles provide faster mass transport than conventional-sized beads. Unfortunately, high pressures are needed to pump solutions through columns containing small resin particles. It is preferable to disperse fine resins in the solution being treated. Screens have been used to separate the resin from the solution, but screens do not retain fines created by attrition of the resin particles. We have developed a separation process based on flotation, which relies on the surface characteristics of the resin, instead of size. The resin is conditioned with a surfactant before dispersing it in the solution to be treated; this increases the hydrophobicity of the resin sufficiently for froth flotation, without introducing surfactant directly into the solution. The surfactant adsorbed on the resin surface does not appear to impair the kinetics of metal ion removal. A flowsheet for an effluent treatment process is proposed; other applications are clearly possible.

Jan 1, 1998