Search Documents

By Paykan Safe

The primary source of fugitive gas emissions in most copper smelters are the Peirce Smith converter operations. The modem trend is towards installation of secondary gas collection systems which are intended to collect fugitive gases from charging, standby, and skimming operations. These have been installed with varying degrees of success. Often, the major source of emissions from the converter area is leakage of process gas from the primary hoods when the converter is blowing. This gas is typically collected by the secondary system and discharged to atmosphere or scrubbed with an alkaline agent. Those smelters considering installation of secondary hoods or scrubbing of gases from secondary systems should first address the issue of gas leakage from the primary hoods. Improving the primary hood gas collection efficiency will often be more cost effective than installing secondary hooding. In the case of secondary gas scrubbing, it will significantly reduce the reagent consumption and operating cost of the scrubbing system. This paper examines the parameters that determine whether or not a primary hood will effectively collect process gases without leakage and demonstrates, using Computational Fluid Dynamics (CFD), the effects of variations in these parameters on the overall performance of the hood. It also looks at the application of CFD techniques in the design of secondary hoods and presents a summary of measured emissions from converter buildings.

Jan 1, 2002

By F. Mucciardi

With the increasing trend to continuous smelting and converting, granulation of copper matte is gaining prominence as a means of decoupling the smelting and converting operations. Moreover, granulation is also being seen as a possible avenue to using higher grade oxygen in converters. By feeding cold solid matte, the oxygen concentration can be increased to compensate for the lower enthalpy feed. This leads to a higher grade of SO2 in the off gas and a lower total flow rate. Current granulation technology relies on the cooling of a falling matte film by water jets. This technology while effective has several drawbacks including those related to safety. Noranda and McGill University have developed a new process (patent pending) for solidifying copper matte (or slag). It overcomes many of the negatives of current technology. The system is based on an air cooled twin roll caster. This: new system uses no water and instead incorporates heat pipe technology to transfer the heat from the solidifying matte to the cooling air to produce a thin strip of 1 to 2 mm in thickness. Testing of a prototype unit demonstrated its viability. This paper describes this newly developed, twin roll casting system that is completely waterless. The advantages of this process as well as the findings from several tests are also detailed.

Jan 1, 1999

By Lincoln McCrabb

Correct measurement and interpretation of viscosity data is critical for design of any thickening and pumping process that involves a non Newtonian slurry. The nickel laterite pressure acid leach (PAL) process relies on producing a slurry of maximum achievable solids concentration. Small variations of 1-2% solids concentration can alter economics significantly. For the Ravensthorpe Nickel Project, a rheology protocol has been developed which optimizes the solids concentration across a range of ore types. The vane yield stress technique has been utilized to accurately quantify the flow of thickened slurry in the lower shear range. A yield stress of 100Pa has been used as a benchmark to determine the optimum solids concentration achievable utilizing deep cone thickening. Statistical analysis of the data shows critical rheology distinctions between ore type, particle size, lithology and geochemistry. Linear and power law models have been applied to rheology flow curves to reconcile the material transport properties with the anticipated thickener underflow solids concentration. Keywords: Vane Yield Stress, Thickening, Rheograms

Jan 1, 2004

By Ali Akbar Mottahedi

Chromate conversion coating is a process for making a complex layer at the surface of zinc galvanized steel which makes the metal more resistant to corrosion, especially at marine atmosphere, and increases the adhesiveness of color. In this work the influences of various compositions on commercial zinc galvanized steel sheet to the color of chromate conversion coating has been investigated at normal temperature and the factors that affect the control and optimization of the process have been determined. A bath composition of 20 g/liter Cr203 and 10 g/liter NaOH and a dipping time of 50 seconds at room temperature (25-30°C) make a desirable color of chromate coating. A slow agitation at a constant pH of I (with additions of NaOH or H2SO4) assures a constant bath condition and develops the color. This kind of coating has more corrosion resistance and this bath condition and composition are also more economical.

Jan 1, 2003

By M. E. Ramos Rada

Mexicana de Cobre, which is part of Grupo Mexico, carried out studies for the construction of a copper refinery in the La Caridad Metallurgical Complex located in Nacozari, in the state of Sonora, Mexico. After the studies were concluded, the decision was made to construct a 180,000 t/y refinery using the state of the art permanent cathode Kidd Process. The basic engineering was developed by Fluor Daniel and the detail engineering and the construction were carried out in record time by the Mexican company Bufete Industrial. During the construction phase, Grupo Mexico decided to expand the refinery, and actions were taken to increase its capacity by an additional 120,000 t/y; the final result was a refinery capable of producing 300,000 tonnes of grade A cathode per year. Construction began in January 1996, and the operation of the first stage began on July 1, 1997. The operation of the second stage commenced on January 7, 1998. The capacity of the first stage was reached in November, 1997 and the total capacity of the refinery was achieved in May, 1998. This presentation describes the process and equipment installed in the refinery, the steps leading to the start-up, the operation and the results obtained during the first two years, the handling of anodes with high impurity contents, and the problems confronted and the way they have been solved. It also includes personnel productivity, the control parameters and the most relevant data on the operation of the process.

Jan 1, 1999

By Bing Song, Fei Xi, Xuewei Lv, Kai Zhang

The electric arc furnace process is a common method to produce high TiO2 slag from ilmenite. The pre-reduction process was proposed in recent years in order to reduce electricity consumption. In order to enhance the pre-reduction degree, high energy ball milling was proposed to improve the specific surface area of the ilmenite prior to reduction. In this study, the carbothermic reduction behavior of milled ilmenite concentrate was investigated. It was found that the ball milling method can result in a higher reduction rate and improved metallization of iron. The metallization of iron increased with increasing the time of ball milling. The metallization of iron with milling reached 89.49% when the time of ball milling was 70 min., while the FeO content decreased with 70 min. of milling from 11.84% to 4.76%.

Jan 1, 2014

By Mary Cunningham

The EPA and DOE have collaborated on a series of studies to evaluate the effectiveness of treatment technologies at stabilizing bulk elemental mercury and wastes containing high concentrations (i.e., with greater than 260 mglkg total mercury) and multiple forms of mercury. The data from these treatment demonstrations are intended to help EPA to determine if regulatory revisions to allow a stabilization alternative for high-mercury subcategory wastes are warranted. In addition to mercury-contaminated wastes, the disposal of bulk elemental mercury is of concern because of the excess quantity of mercury in the Defense Logistics Agency (DLA) stockpile, as well as other potential sources of excess elemental mercury. The studies evaluated the effectiveness of several technologies at: I) stabilization of mercury in a "hard-to-treat" matrix; and 2) conversion of elemental mercury into a stable waste form for disposal. A surrogate waste was designed for the study on high-mercury wastes, which included an organic form of mercury, elemental mercury, and several mercury salts in an inorganic matrix. The surrogate waste and the bulk elemental mercury were treated by the vendors, and the treated waste forms evaluated for mercury Icachability, using both the TCLP and an automated, constant-pH leaching protocol. Constant pH leaching was conducted at pH 2,4,6,8 10 and 12 for 14 days at each pH. The leaching data demonstrate that the stability of the mercury in three treated waste forms varies widely across the pH range tested. Clearly, the stability of mercury in these treated waste forms will be highly dependant on the disposal conditions. The combination of site-specific disposal conditions and appropriate treatment technology must be considered as decisions are made about disposal of high-mercury wastes.

Jan 1, 2003

By Zviad Kovziridze

Structure of celsian ceramics in BaO-Al2O3-SiO2system is studied with electron microscope in the entire temperature region of baking interval. The process of the pores filling and the full consolidation of material growth at comparatively high temperatures of baking intervals are described.

Jan 1, 2006

By Peter Willbrandt

Norddeutsche Affinerie's routes date back to the 18th century. NA was established in 1866 as a joint stock corporation. NA's core business covers the production of copper cathodes from primary and secondary raw materials and the processing of them into wire rod and shapes. Part of the shapes are processed into pre-rolled strip and shaped wires within the Group. With some 3,200 well qualified and highly motivated employees, the NA Group produces some 560,000 tonnes of copper cathodes, 370,000 tonnes of wire rod, 230,000 tonnes of shapes, 130,000 tonnes of pre-rolled strip as well as 70,00 tonnes of strips and shaped wires annually. NA's product range is complemented primarily by precious metals, selenium, sulphuric acid, lead and nickel sulphate. The paper will give an insight into the performance of NA and its business units with regard to production, environmental and health protection and occupational safety.

Jan 1, 2006

By Vladimir Lobanov, Vladimir Skorohodov, Boris Radionov, Olga Makovskaya

"The synthetic sorbents and the activated carbons which are used for the metals extraction from weak process liquors are rather expensive. It is propose to use mineral and synthetic high-porous substances which sharply increased sorption properties by special processing. For achievement the desirable properties sorbents are impregnated by specially prepared solutions. Such solutions should contain the substances or its anionic forms which on the one hand are strong enough fixed in a supporter pores, with another are capable to form the insoluble compounds with extracting metals. Selectivity is provided by chemism of the reagent interactions with extracting metal. Due to the high concentration of a reacting ion in a sorbent phase the capacity and rate of sorption increases. Formed insoluble compound remains in a phase of the sorbent and necessity of its filtration disappears. For synthesis the sulfhydryl compounds which chemical properties allow to increase degree of extraction and capacity of the activated carbon were used. At hydrometallurgical processing of precious metals mineral raw materials the commercial solutions with the concentration of gold from 0,1 to 5 mg/dm3 are received. Commonly gold is precipitated from cyanic solutions by the zinc dust. The sorption methods are widely applicable. But the synthetic sorbents and the activated carbon using to these purposes are rather expensive. Expenses for sorbents even at its regeneration can reach 10-15 % from total expenses of gold extraction from ores. When sorbent regeneration, mostly for carbon, is not provided, this share increases to 30-40 %. Thereupon search of the sorbents combining availability, the sufficient capacity, demanded degree of extraction and the low price is actual. For the specified purpose it is offered to use the mineral and synthetic high-porous materials which sorption properties are sharply rose by special treatment. Among such substances are natural zeolites, silica gel, lignine et al. Similar treatment can improve the sorption properties of sorbents used in practice, particularly, the activated carbons. The simplest treatment of potential sorbents consists in its impregnation by specially prepared solutions. Such solutions should contain substances or its anionic forms - impregnating agents. These agents should be on the one hand strong enough fixed in a carrier pores, on the other hand are capable to form with extracting metals insoluble compounds. The more strong compounds are formed the high degree of metals extraction from solutions. The sorbents with similarly changed properties are named the impregnated sorbents."

Jan 1, 2008

By Peter Willbrandt

The flash smelter at NA was commissioned in March 1972 with an initial throughput of 50 tons of dry copper concentrate per hour. As a result of various measures, for example, oxygen enriched process wind, extension of the radiation part of the waste heat boiler, etc., the throughput could be increased to the present 70 tons per hour of dry concentrate. NA's plant is located on the outskirts of the city of Hamburg. The flash smelter's location and the growing awareness of the German population as regards environmental issues necessitate again and again considerable capital expenditure being spent on environmental protection. Thanks to the numerous small and large measures taken to protect the environment the emissions of dust, heavy metals such as arsenic, copper, lead, etc., and as well SO, could be drastically reduced. This paper will be giving an overview on the present state of the flash smelting process and the impact of the increasing environmental awareness at NA.

Jan 1, 1993

By R. Mehta, M. Misra, X. Su

"The conventional methods to assess Acid Mine Drainage (AMD) potential of the waste rocks and tailings are based on wet chemistry and leachability tests. These methods are time consuming and expensive. There is a growing interest to develop alternate techniques to establish the reactivity of acid mine tailings and stability of treated waste forms. The Electrochemical Impedance Spectroscopy (EIS) is a reliable non-invasive technique which can be used for quick estimation of reactivity of the potential acid generating tailings. In this paper the utilization of the EIS technique for the estimation of reactivity of tailings is discussed. EIS can also be used to predict the long term stability of different stabilized waste forms.IntroductionMetal contaminated mine drainage is one of the most persistent environmental problems facing the mining and mineral processing industries today. Of all the mine drainage pollutants, acid mine drainage has become a substantial concern because of the potential long-term environmental implications and the accompanying liabilities. The main source of acid mine drainage is the tailings containing sulfide-ores which are generated during the ore processing. When these sulfide minerals, particularly pyrite and pyrrhotite, are exposed to oxygen and water they begin to oxidize. The initial chemical reactions produce acid and the acid dissolves heavy metals present in the tailings. Rainfall and snow-melt flush the toxic solutions from the waste sites into the downstream environment [1-2]. In addition to mining tailings, several Department of Energy (DOE) sites contain wastes which are contaminated with radionuclides and heavy metals."

Jan 1, 1999

By P. A. Davidson

"We discuss the influence of a static magnetic field on jets, vortices and turbulence. This is particularly relevant to D.C. braking in slab casting. Our main conclusion is that, typically, the magnetic field destroys mechanical energy, via joule dissipation, but is unable to destroy momentum. Rather, it continually rearranges the momentum in such a way that the energy falls.IntroductionIt is well-known that a static magnetic field can suppress motion of a liquid metal. That is to say, movement of the liquid across the magnetic field lines induces a current. This leads to Joule dissipation and the resultant rise in thermal energy is accompanied by a corresponding fall in kinetic energy.This phenomenon has been exploited in a range of metallurgical processes. For example, in the continuous casting of large steel slabs, an intense, static magnetic field is commonly used to suppress motion within the mould. The objective is to keep the free surface of the liquid quiescent, thus avoiding the entrainment of surface debris. In other solidification processes, such as techniques for growing semi-conductor crystals, it is widely believed that natural convection has a detrimental effect on the metallurgical structure of the solid. Again, the imposition of a static magnetic field is seen as one means of suppressing these unwanted motions. Finally, magnetic damping is used in the laboratory measurements of chemical and thermal diffusivities, particularly where solutal or thermal buoyancy can disrupt the measurement technique.In this paper we shall look at the damping of jets, vortices and turbulence. Our aim is to present a unified theoretical framework from which the many published studies may be viewed."

Jan 1, 1999

By P. S. Arthur

The ISASMELT? process is a submerged lance smelting technology operating in smelters in Australia, the USA, Belgium, India, Germany, Malaysia and China. Further plants are under construction in Peru and Zambia. Following the invention of the Sirosmelt lance technology Mount Isa Mines recognised the commercial potential in the novel top blown bath smelting process and embarked on a development program that has lasted more than 25 years. After successful operation of pilot plants and demonstration plants producing copper and lead, Mount Isa Mines decided to license the technology to external companies. Since the purchase of Mount Isa Mines by Xstrata in 2003, Xstrata Technology has assumed responsibility for transferring the technology to ISASMELT? licensees. In the 15 years since the first commercial furnaces started operation plants have been constructed (or are under construction) with a combined annual smelting capacity of more than six million tonnes of concentrates or secondary raw materials. Process development continues on the commercial scale plants at Mount Isa and elsewhere. Many of the improvements implemented by plant operators have been passed on to, and adopted by, other licensees. Exchange of ideas and technical improvements occurs through ad hoc visits to fellow licensee sites and through regular licensee workshops arranged by Xstrata Technology. This paper updates the reader on the status of various ISASMELT? plants either operating or under construction. It highlights the important role that the technology provider?s operational experience plays in ensuring that new smelting plants ramp up quickly to nameplate capacity.

Jan 1, 2006

By S. C. Dhara

The recovery of Platinum Group Elements from various industrial scraps and spent materials in the form of high and low grade, such as, impure metals, matte, catalysts and other ceramic substrates, etc., has .been described by using high pressure reaction method. Nickel, Stainless Steel, Titanium and glass lined reaction vessels? are used in the reaction process. Primarily, the method involves either direct leaching of the substrates from the metal value or dissolving the precious metal from the substrate. Both acids and alkalies are used along with other reagents in the reaction process. The temperature and pressure of the leaching process are the main criteria for the reaction kinetics.

Jan 1, 1989

By N. Verbaan, E. Bourricaudy, M. Dry

"Starfield Resources is developing a novel circuit for the recovery of nickel, copper, cobalt, iron oxide, sulphuric acid and precious metals from the Ferguson Lake deposit in Nunavut, Canada. In this deposit, pentlandite is too finely disseminated in pyrrhotite for the production of a smelter-grade nickel concentrate at an acceptable nickel recovery, so established technology is not applicable and a novel chloride-based circuit is under development. The enabling aspect of this circuit is the hydrolysis of ferric chloride to hematite, releasing gaseous hydrochloric acid that is recycled. Conventional steps are used for separating and recovering the valuable metals from the chloride solution generated. This paper briefly outlines the circuit and presents the results of experimental work on the enabling steps, viz. the oxidation and hydrolysis of iron chloride to hematite and gaseous hydrochloric acid.IntroductionThe Ferguson Lake bulk sulphide ore body in Nunavut, Canada, owned by Starfield Resources Inc., contains significant amounts of base and precious metals but its mineralogy is such that it is not amenable to conventional processing. Pentlandite, for example, is too finely disseminated in pyrhhotite for even modem techniques such as fine grinding and improved flotation reagents to be effective [ 1] and extracting the value requires processing the entire bulk sulphide, including the pyrrhotite. To give the project a total green footprint, in terms of both carbon emissions and acid rock drainage, Starfield imposed the following requirements:• No reactive tailings to generate acid rock drainage.• No gaseous emissions other than normal atmospheric constituents.• No liquid effluents.• No regular consumption of fossil fuel.• High recoveries of all the valuable metals."

Jan 1, 2011

By Kandipati Sreenivasarao

Ion flotation is a promising separation process for continuously removing toxic metal ions from dilute process effluents. After treating the effluent with appropriate surfactant(s), the metal- bearing species adsorb onto the surface of rising gas bubbles and can be collected as foams. Suitable collectors have been identified for most of the elements of the periodic table. However, a better understanding of the thermodynamic, kinetic and engineering principles that determine the performance of ion flotation systems would facilitate commercial utilization of this technology. A model system of sodium dodecylsulfate-ethanol has been studied for the removal of Cu (11) from dilute solutions, using laboratory-scale flotation columns. This paper reports the effects of the air flow rate, solution height, foam drainage zone height and col1ector:metal ion ratio on the flotation kinetics, ultimate recovery of metal, flotation product grade, foam losses and effluent quality. Preliminary results for Pb (11) removal are also reported.

Jan 1, 1993

By D. W. Collins

Several organic and inorganic substances are widely used to control deposit structure and morphology during the electroprocessing of copper. Methods for monitoring the levels of thiourea, glue and guar gum during electrorefining and electrowinning have been successfully developed under the trade names of Reatrol and CollaMat. Other instrumental methods have been developed for additives and decomposition products associated with the electroplating of copper and other metals. Generally, these methods have been found to be either insufficiently sensitive or lacking in the desired selectivity for some or all of the additives. These procedures have mostly employed DC techniques; i.e., cyclic voltammetry, Tafel analysis, etc. In this work, chronopotentiometry (CP) and AC voltammetry were used to examine the interaction of glue, guar gum, thiourea and chloride during the electroplating of copper onto a platinum electrode. In addition, the interactions between the additives have been explored. It was found that glue in pure electrolyte (H2S04 and CuS04 only) had no effect on the chronopotentiogram. Glue was only active if chloride ions were present. The addition of thiourea resulted in several different chronopotentiograms depending on the presence of either chloride or chloride and glue. Thiourea used in conjunction with glue and chloride showed a significant increase in the polarization during copper deposition when compared to the electrolyte containing only glue and chloride. The use of a modified channel electrode further increased the sensitivity of CP. The use of AC voltammetry was explored as a technique to monitor some of the additives. AC voltammograms have more spectral detail then their DC counterparts and it is possible to monitor some of the additives at very low concentrations with AC techniques.

Jan 1, 1999

By Uday B. Pal

In the electrochemical vapor deposition (EVD) process, gaseous cation precursors are passed over one side of a porous substrate, and oxygen is passed on the other side of the substrate. The gases diffuse and react within the porous substrate, and the pores get filled with the desired solid oxide. Subsequent solid state electrochemical transport through the solid oxide in the pores continues the reaction, and the film grows over the porous substrate. The EVD process has been used to deposit lanthanum chromite interconnection films and yttria stabilized zirconia electrolyte films over porous air electrodes. The EVD growth of these solid oxide films is found to be parabolic in nature, which indicates that the solid state transport (diffusion) of ions through the film controls the growth. This solid state transport can be analyzed using Wagner's treatment of the electrochemical transport. Conductivity measurements and the information on the defect structure of the oxide can be combined with the EVD growth rate measurements to calculate the solid state transport properties (transport numbers and partial conductivities) of the rate-controlling minority species in the oxide. Using this approach, the EVD growth of other electronic, mixed conducting and ionic solid oxide films can also be analyzed.

Jan 1, 1992

By Tatsuki Uzawa, Takashi Nagai

The consumption of Nd and Dy is increasing dramatically because of an exceptionally high demand for Nd-Fe-B-(Dy) magnets and a significant amount of the magnets are wasted. It is important to develop a recycle process the elements from the wasted magnets. In this study, Nd and Dy were extracted from the magnets by silver at high temperature. Nd can be extracted more than 70 % by silver. However, Dy is extracted only 25 % in the same experimental condition.

Jan 1, 2014