Search Documents

By Zhihe Dou, Zimu Zhang, Guozhi Lv, Yan Liu, Xiaoli Jiang

"Cyclic heat stewed slag washing water carries high content of alkali and calcium and may cause serious tube scaling and impose an adverse impact on normal production. This study proposes a solution to utilize washing water by absorbing and mineralizing CO2, potentially restraining scaling and being able to create calcium carbonate powders. Effects of water flux on water quality, utilization ratio of CO2 and yield of calcium carbonate powder have been investigated; meanwhile, features of calcium carbonate powder are also represented. On the other hand, effects of factors such as as injection flux, pressure of CO2 on utilization ratio of CO2, morphology and purity of calcium carbonate are also investigated. The results show unambiguously that after soften injection of CO2, calcium ions were removed effectively via precipitation, alleviating the scaling problem. High purity yet fine carbonate powder could be achieved.IntroductionNowadays, 0.34 tons of blast furnace slags will be produced when producing 1 ton of pig iron; ensuing that, 0.12 tons of steel slag will be generated with 1 ton steel production while 1.57 billion tons of steel output all over the world in the year of 2012. It is therefore a critical issue to realize zero discharge of steel slags to achieve sustainable development and cyclic economy of iron and steel industry. In recent years, research institute of MCC and China JINGYE engineering company developed a heat stewed steel slag self-decomposition technology GENERATION III to solve the problem of instability of steel slags and realize the zero discharge. However, the problem of circulation line scaling which may cause the clogging, even exploding, need to be solved. The principles of the technology are: directly spraying water to the high temperature steel slag when it is poured into the hot closed pot, realizing the selfdecomposition via utilizing the waste heat of steel slag. The washing water is recycled to achieve a cyclic utilization. The process is shown in Figure 1."

Jan 1, 2014

By Sang-Su Lee

This paper shows the application of the porous plug system in the Mitsubishi continuous copper smelting and converting process. This system has already been adopted and utilized in the steel industry to enhance productivity. Recently, some copper smelters have adopted this system but the results have not been satisfactory. The porous plug system was installed at the anode furnace in December 2001 to reduce the oxidation time and decrease the oil consumption. A good effect was that the nitrogen stirring of the melt through porous plugs improved the melt heat transfer. As the result of the enhancing heat transfer the oil consumption and the build-up inside the furnace were actually decreased. But until now the oxidation time has not been sufficiently reduced. In the future, further research and tests are needed in order to increase the productivity and save costs.

Jan 1, 2003

By Junji Shibata

Some fundamental studies were carried out in order to produce composite powders comprising of two or three metal salts by using liquid-liquid extraction and to develop the control technology of the particle size. The combination of samarium and cobalt was selected as the two component composite powders. Both stripping and crystallization occurred at the same time by emulsifying the organic phase loading the two metals extracted with Versa tic Acid 10 and the aqueous solution containing oxalic acid. The effect of aqueous pH, oxalic acid concentration and agitation speed was examined on some properties such as crystallization percent, particle size and shape of each metal oxalate powders obtained in this process. The analysis by using EDX showed that the two metal oxalates were distributed uniformly at the same ratio as the organic phase composition.

Jan 1, 2001

By William Petruk

The behaviour of sphalerite during mineral beneficiation of base metal ores has been studied at CANMET and other institutes for at least 15 years by determining the liberations of sphalerite in mill products and calculating the recoveries of liberated and unliberated sphalerite in zinc concentrates. Sphalerite in base metal ores commonly occurs as layers and as interstitial material between pyrite. Layered sphalerite is generally liberated during primary grinding, but interstitial sphalerite requires re-grinding to achieve liberation. Around 95% of liberated sphalerite is generally recovered in zinc concentrates frau zinc circuit feeds. A series of tests was conducted on sphalerite in the ore of Brunswick Mining and smelting during a continuous fine tuning operation of the concentrator. It was found that a grind of 80% minus 37 micrometres was required to liberate the interstitial sphalerite. The fine grind increased Zn recoveries from 75% to 78-80%, but produced liberated slimed sphalerite which was lost. Since regrinding to a fine grain size is needed to obtain the desired sphalerite liberation, a method of recovering the slimed sphalerite is required.

Jan 1, 1990

By Peter K. Liaw, Charlie R. Brooks, David C. Joy, Wei Zhao

In this paper, effects of oxidation, porosity and fiber-fabric stacking sequence on flexural strength of a continuous silicon carbide fiber (SiCr) fabric-reinforced SiC ceramic-matrix composite (CFCC) were studied. The failure mechanisms were correlated with flexural strengths of CFCC samples, both before and after oxidation. Microstructures and fractography were investigated using scanning electron microscopy (SEM). The chemical change after oxidation, such as Si, C, and 0, and their distributions, were detected by the SEM energy-dispersive X-ray spectroscopy (EDXS) line-scan chemical analysis technique. These effects on the strength of the CFCC can be attributed to following reasons: (i) The decrease in the flexural strength after oxidation is mainly due to degradation of the strength of Nicalon fibers and the damage of fiber/matrix interface both caused by high-temperature chemical reactions, (ii) Porosity is not too important in affecting the strength of the CFCC, when the bonding of the forced flow chemical vapor infiltration (FCVI)-SiC matrix is stronger than that of the fiber/matrix interface. However, a higher porosity content will be harmful, because higher porosity will both decrease the effective elastic modulus of the FCVI-SiC and make pore-linkage easier to occur, which is more likely to cause premature failure, (iii) The variation in the lamina stacking sequence of the CFCC changes the elastic stress distributions along the thickness direction of specimens, the magnitude of ceramic matrix-cracking stress, the effective elastic moduli of the laminate, and different crack initiation sites as well as different failure modes, and thus, leading to the scatter in the flexural strength of the CFCC.

Jan 1, 1998

By Gus Van Weert

This paper describes the results of autoclave testwork where ferric nitrate was hydrolysed in the presence of certain cations and anions and the resulting hematite analyzed for foreign constituents. For the cations Zn++, Ni++, Cu++, and AI+++, selectivity factors of over 107 were found. Magnesium gave 3.106. These factors are calculated as Me/Fe in solution over Me/Fe in the hematite; Me representing the metal in ion added. As-a result of the testwork at Delft University of Technology, BUDELCO (the Netherlands electrolytic zinc producer) ran a series of ferric nitrate hydrolysis tests in the presence of 10 additional trace elements. Impurity levels were prejudiced on Me2 EPHA extraction of iron from their zinc circuit, followed by HNO3 stripping. Good selectivity against base metals was confirmed, but trace elements forming anions (As. Sb) and sulphate were incorporated in the hematite. These BUDELCO results are also presented.

Jan 1, 1995

By J. W. A. Morris

To investigate the use of centrifugal fields in fused salt electrowinning cells, a high temperature rig has been designed, constructed and commissioned. Initially, the cell has been applied to the fused salt electrowinning of zinc. Current efficiencies of 93% have been obtained for inter electrode gaps as small as 8mm for 70mm diameter electrodes rotating at 100rpm. The construction of a semi-rigorous physical model has shown the potential exists to extend the use of centrifugal fields to the electrowinning of light metals.

Jan 1, 1994

By Gary K. Elliott

Many industrial processes generate hot waste gases which contain particulate pollutants. Conventional clean-up techniques suffer limitations either because collection efficiency is low or because the gas must be cooled before treatment. thereby increasing costs and preventing energy recovery. The application of increasingly stringent environmental legislation to the non-ferrous metallurgical industry is presently illustrating these conventional technology limitations. Low density ceramic media allow filtration to ta,ke place at 'high temperatures and are now rapidly becoming accepted In many industries. This paper reviews experiences with a proprietary low density ceramic filter element. CerafH. It includes consideration of the structure, composition. typical operating and case studies with particular reference to non-ferrous metallurgical furnace applications.

Jan 1, 1992

By S. Moussa

The formation of boron-doped nickel aluminides Ni3AI, (76 at. % Ni) from elemental powders by reaction synthesis using reactive sintering was studied. The process involves the mixing of elemental powders of nickel and aluminium with various wt % of boron up to 1 wt % boron. Nickel and Aluminium powders were mixed in the correct proportion to form the intended boron-doped nickel aluminide intermetallic. XRD, SEMI EDS, Image analysis and Archimedes principle; were used to study the effect of Boron addition on the final microstructure, bulk density, average grain size of as reactively-sintered nickel aluminides (boron-doped), compared with no boron addition. The results showed that at greater boron content than 0.3 wt %, a two-phase non-equilibrium microstructure of consisting of NiAI phase in NiJAI matrix was formed that have been primarily retained even after heat treatment for 5 hours at 1000 °C. Boron was present in solid-solution within both the NiAI and the Ni3AI (in greater amounts) phases.

Jan 1, 2001

By Y. Moriya, Y. Sadayoshi, Y. Nonogaki, Y. Takeda

"Preparation and growth processes of CaF2 on Si(111) and of . InxGa1-x,As islands on CaF2 by molecular beam epitaxy (MBE) are described. It was found that first of all the Si(111) surface treatment process to obtain the 7x7 reconstructed structure was necessary to ensure the cleanness of the surface and to grow a flat and high quality CaF2 on it. Growth of InxGa11-x,As islands on CaF2 was tried by droplet heteroepitaxy using the same MBE reactor. In,GaxGa1-xAs islands were successfully grown epitaxially, and the size and density of the islands dependent on the In composition were investigated.IntroductionThough semiconductor/semiconductor heterostructures are widely used for many device applications, small band off-sets of the conduction bands and the valence bands restrict the utilization of the intra-subband transitions to far-infrared regions. With InAs as the quantum well and fluorides as the barrier layers, we can design three-electronic-level systems in the infrared region, which is the low loss transmission window of the silica optical fibers. To realize those structures, we have grown InxGa1-xAs islands on CaF2 thin films that were epitaxially formed on Si(111) substrates by molecular beam epitaxy. By the droplet heteroepitaxy that we invented, the InxGa1-xAs islands with height of -10 nm have been obtained successfully. Optimum processing to obtain atomically smooth surfaces of Si and CaF2 and high quality InxGa1-xAs islands is reported.ExperimentsMBEMachineCaF2 was grown on Si(111) and InxGa1-xAs islands were grown on CaF2 successively by MBE. The MBE machine consisted of a growth (or reactor) chamber and a loading chamber. The reactor chamber was equipped with Ga, In, As and Er metal source cells and CaF2 and BaF2 source cells. Cell materials were P-BN for Ga, In and As metals, and were graphite for CaF 2, BaF 2 and Er to avoid reaction with BN cells. The electron gun and screen were attached to the reactor to observe the RHEED pattern during the substrate surface treatment and the growth of CaF2 and InxGa1-xAs islands. The substrate manipulator was designed to heat up the Si substrate up to 1,200°C for the surface cleaning. The QMS was also equipped to analyze the residual gas species in the reactor chamber. The base pressure of the reactor chamber was 2-5x10-11 Torr, being pumped by ion pump and the liquid nitrogen shroud"

Jan 1, 2000

By Jens Decker

"In consideration of energy savings the ideal refractory furnace lining should possess the following features:??Lowest thermal conductivity possible in order to avoid heat loss.??Single component lining in order to allow freeze plane changes caused by wear, infiltration and temperature changes of the furnace.??Resistance against mechanical wear from cleaning tools and stirring in order to allow maximum output without equipment downtime due to maintenance.??Resistance against thermo-chemical attack from aluminum and alloying elements.However, refractory materials with a low thermal conductivity typically possess a higher porosity and this leads to lower strengths and resistance against chemical attack and wear. Hence, as a compromise, multi layer linings are required in order to meet energy saving standards.In this paper we present the features of chemically phosphate bonded dense and light weight refractories and how such refractories can contribute to energy savings.IntroductionIn several reports, the U.S Department of Energy published theoretical energy requirement limits for aluminum production as a future target, with recommendations on how to reduce energy losses. The reports provide a basic description of the processes and equipment involved, their interrelationship, and their effects on energy consumed. The report uses onsite process measurements as benchmarks that industry uses to compare performance between facilities and companies [1]. The energy consumptions used in this paper are primarily based on numbers published by the Department of Energy. However, their reports do not consider the potentially significant energy losses from process interruptions due to a lack of preventive maintenance and material deterioration over time. Further, the Department of Energy reports do not consider equipment costs and availability. Energy input to metal output depends on factors beyond energy losses through the furnace wall. For instance, a focus on energy savings should consider fixed output costs due to depreciation of the equipment and the plant."

Jan 1, 2009

By Felipe P. D. Lopes, Jr. dos Santos, Sergio N. Monteiro, Frederico M. Margem

"Continuous and aligned fiber composites provide the highest possible reinforcement for a polymeric matrix. In particular, the impact resistance is significantly increased in comparison with a low energy absorbed brittle polymer. For this reason, investigations have been carried out with both synthetic and natural fibers as a way to improve the toughness of polymeric composites. Among the natural fibers, ramie was not yet been studied for its reinforcement effect to make tougher polyester composites. Thus, the present work assesses the impact toughness of polyester composites incorporated with different amounts of ramie waste fibers.IntroductionIn most engineering and other technological areas, the use of materials associated with low energy processing conditions is gaining attention for the possible environmental benefits. This offered an incentive towards the substitution of natural renewable and biodegradable materials for the traditional energy intensive synthetic materials [1]. Natural fibers from both origins: animal, such as silk and wool, and vegetable, such as cotton and jute, are typical examples of those environmentally friendly materials. Low cost and highly reduced processing machinery wear are important advantages of the natural fibers over the most common synthetic ones such as glass fiber and nylon. For these reasons, polymeric composites reinforced with natural lignocellulosic fibers have nowadays been the subject of investigation [2,3].The mechanical strength is one important property of lignocellulosic composites to access the possibility of uses like structural materials for building parts such as doors and panels, as well as furniture. In this case, mechanically strong fibers like sisal, jute, curaua and ramie [4-7] are most convenient. Moreover, the relatively low fiber/matrix interfacial shear stress in these composites is associated with higher impact energy. In fact, a greater energy has to be expended for the rupture of a weak interface. The many cracks that are formed by impact tend to branch during the fiber pullout from the matrix [8]. A larger number of cracks correspond to a greater fracture surface and consequently higher toughness."

Jan 1, 2008

By Gary K. Elliott

Many industrial processes generate hot waste gases which contain particulate pollutants. Conventional clean-up techniques suffer limitations either because collection efficiency is low or because the gas must be cooled before treatment. thereby increasing costs and preventing energy recovery. The application of increasingly stringent environmental legislation to the non- ferrous metallurgical industry Is presently illustrating these conventional technology limitations. Low density ceramic media allow filtration to take place at high temperatures and are now rapidly becoming accepted in many industries. This paper reviews experiences with a proprietary low density ceramic filter element, Cerafill. It includes consideration of the structure, composition. typical operating and case studies with particular reference to non-ferrous metallurgical furnace applications.

Jan 1, 1992

By Kenneth G. Thomas

This paper reviews the alkaline and acid gold autoclaving experiences gained at Barrick Gold Corporation. Alkaline autoclaving was operational at Barrick Mercur, Utah, U.S.A., on carbonaceous/sulphide refractory ore for eight years commencing in 1988. Acid autoclaves have been operational at Barrick Goldstrike, Nevada, U.S.A., on sulphide refractory ore since 1990 and now process 17,500 stpd of ore through six large autoclaves. Information is presented on operating costs, materials of construction, reagent requirements and flow sheet developments that reduced capital and operating costs.

Jan 1, 2000

By Norihisa Iida, Yutaka Koshiba, Tsutoipu Masui

"Mitsubishi Materials has many years of experience in the production of oxygen free copper (OFC) and its alloys with a fully continuous-casting process. Four grades of OFC, commercial, electronic, superconductor, and ASTM class I are available according to user needs such as stabilizer for superconductivity, magnetron, and ultra-vacuum systems. Along with Cu-Ag and CuSn, we offer OFC based copper alloys such ·as Cu-Cr-Zr, Cu-Fe-P, Cu-Ni-Si and others, that are suitable for lead frame and connectors. Within the maximum sizes of 260mm X 1050mm for cakes and 385mm diameter for billets, we are very flexible and can adjust the ingot size to customer’s requirements. Other products that we can supply are semi-finished products such as hot rolled sheet, ·forged blank, extruded rod and finished products like mold for continuous casting of steel, ring mold for non-ferrous casting and backing plate for sputtering target.IntroductionMitsubishi Materials Corporation developed mass produced high quality oxygen free copper and. high copper alloy ingots in the 1960's. We produce 60,000 - 70,000 tons annually giving us 22 - 23% share of the world's market.Our oxygen free copper and. copper alloys are produced with a fully continuous casting process using only high-grade copper cathodes from our Naoshima and Onahama refineries. The raw material is melted and cast in' a carefully controlled atmosphere resulting in a product with low impurities and excellent properties.Using a controlled atmosphere it is possible to produce high quality copper alloys including active elements like chromium (Cr), zirconium (Zr), titanium (Ti), and magnesium (Mg) which are difficult to produce using standard batch casting methods.Using our own cakes and ·billets we produce and supply worldwide wrought materials like molds for ferrous and non-femous casting. These products receive special patented thermo-mechanical· treatments resulting in high strength and excellent conductivity with low cost."

Jan 1, 2000

By J. Alberto Vázquez M.

A sensor employing yttria-stabilized zirconia (YSZ) was used to determine the oxygen activity of molten copper at laboratory scale at temperatures of 1200° and 1300 dc. The reference electrode was a Ni-NiO mixture. The amount of the deoxidizing agent (CU3P) ranged from I to 3% of the mass of copper. Thermodynamic analysis of the Cu-O-P liquid system was carried out to predict the required deoxidizing agent and the final composition of the molten copper. Both results, calculated and experimental, show that the oxygen removal is more efficient at lower temperatures. The kinetics of the deoxidizing reaction is very fast in the first minutes of the treatment. A metalography analysis of rapid cooled samples show the oxygen and phosphorus distribution

Jan 1, 2003

By William A. Apel

Several different strains of bacteria have been shown capable of reducing hexavalent chromium, Cr(VI), to Cr(III), a less toxic, .. more readily recoverable form of Cr. This paper examined the Cr(VI) reduction efficacies of 3 different Cr(VI) reducing bacteria: Pseudomonas f1uorescens LB300., Pseudomonas aeruginosa PAOI, and Pseudomonas aeruginosa PAOI (pCROI) It was demonstrated that all three bacterial stratns reduced Cr(VI) primarily during their exponential growth phases while using glucose as their carbon and energy source. Significant differences in the three organisms' Cr(Vl) reduction capabilities depending on initial Cr(VI) concentrations were also demonstrated. P. aeruginosa PAOI showed superior Cr(VI) reducing capabilities over the. entire range of Cr(VI) concentrations tested while the Cr(VI) reduction capabilities of the other two strains were increasingly inhibited as Cr(VI) concentrations increased.

Jan 1, 1991

By Steven Wright

BHP Billiton?s Olympic Dam copper flash smelter employs the direct to blister process for smelting high grade copper concentrates. SO2 evolution during tapping gives rise to safety concerns. A thermodynamic model for the blister copper (Cu-Fe-S-O) was used to predict the volumes of SO2 evolved. The Multiple Phase Equilibria Model (MPE) was used to evaluate the slag chemistry inside the furnace. The blister copper model was used to explore the relationship between %S and %O in the copper and the amount of SO2 evolved on cooling. The volume of SO2 evolved was sensitive to the O content with reduction to levels below 0.2 ? 0.15% likely to suppress SO2evolution on cooling. Concentrations of S and O in copper samples from trials generally lay above the equilibrium line calculated for an average temperature of 1275C and a partial pressure of SO2 of 1 atm. Consequently there is a thermodynamic driving force for SO2evolution when cooling to this temperature during tapping. A number of potential process options to suppress SO2 evolution on tapping were investigated thermodynamically. Some of the options require treatment of the blister in a forehearth or separate furnace, while others impact on current practises in the flash furnace with slag present. The opportunities that these options present are discussed.

Jan 1, 2006

By Thomas M. Harris

Cation exchange is not sufficiently selective to be used for the removal of heavy metal ions from a general industrial wastewater. However, if the metals can be converted to polyvalent anions through complexation, they may be removed both selectively and efficiently by anion exchange. This approach, referred to as chelation-assisted anion exchange (CAAE), has been examined using industrial wastewater samples contaminated with Ni2+ and Cr3+. For this particular application, the Ni2+ is complexed with 8-hydroxyquinoline-5-sulfonic acid, and the Cr3+ with sulfosalicylic acid. Removal efficiencies and adsorption isotherms for both the complexants and the complexes were determined in batch-mode tests.

Jan 1, 1994

By W. K. Tolley

The Bureau of Mines is investigating hydrometallurgical processing techniques to recycle metals from semiconductors and other advanced materials. Cadmium and tellurium were recovered from CdTe scrap produced in the manufacture of infrared optic devices. Sulfation, ferric chloride leaching, and oxygen-pressure leaching have been tested. Cadmium dissolution was achieved using oxygen-pressure leaching in dilute sulfuric acid. However, no satisfactory scheme for dissolution of the higher valued tellurium has been devised. Leaching the ground CdTe for 75 min at 110°C in 1.1M H2S0, under 120 psig 0, yielded 99.5% Cd extraction. Tellurium remained in the leach residue as TeO, and elemental tellurium; residual cadmium was less than 0.5%. The cadmium in the leach liquor was purified of coextracted metals such as gallium and iron by adjusting the pH. The cadmium was recovered as cadmium sulfate crystals by evaporating the solution. Recovery of by product metals, notably gallium, is possible.

Jan 1, 1991