Search Documents

By Joel Anderson

Allvac 718Plus is a newly developed superalloy with a good potential for use in fabricated aircraft engine structures when service temperatures exceed 650°C; the limit for standard alloy 718. Fabrication involves welding, where cracking usually is a prohibitive factor. Comparison of the solidification cracking behavior between these two alloys was made by Transvarestraint testing. It was shown that the total amount of cracking was significantly lower for 718Plus alloy, which was associated with a lower amount of ?/Laves or ?/NbC eutectic-type constituents. This in turn is believed to be due to the lower iron content of the Allvac 718Plus material. The analysis of alloying element segregation both within primary dendrite and interdendritic constituents clearly indicates that the segregation of Nb is the controlling factor in determining the final solidification microstructure in these alloys. The Nb concentrations of these constituents are significantly higher compared to the bulk alloy concentration. This was confirmed by the SEM-EDS analysis and calculations assessed with JMatPro, the latter also indicated that alloy 718 is more prone to form Laves and NbC eutectic-type constituents compared to Allvac 718Plus material.

Jan 1, 2008

By N. Mizutani, S. Harada, Z. Asaki, T. Tanabe

"The development of lead-free solders is urgent in view of environmental standpoints. In this -work the wettability of tin-bismuth- silver solders on copper was studied. Three kinds of fluxes were used. The wettability of conventional eutectic tin-lead .solder exhibited an excellent level over the other solders of tin-bismuth systems. Poor wettability of the tin-bismuth solders may be caused by the growth or dendritic copper-tin compounds at copper/solder interface, in contrast to the case of tin-lead'· solder. The wettability was improved by the addition· of silver in the solder. In this tin bismuth- silver system, silver was abnormally concentrated at the copper I solder interface even in the initial stage of contact. The wettability of the solder and the thickness of compound formed on the copper have a good correlation; the solder containing 2% silver exhibited the best wettability and the formation rate of copper-tin· compound on the copper was slowest.IntroductionSocial demand to avoid lead use in the industrial fields has been recently promoted· (1) because of the environmental protection of water resources. Especially the lead-bearing solders have been widely used in electronics and automobile products, and it is urgent to replace them with nontoxic materials (2)-(4). Thus the development of lead-free solders becomes an indispensable subject to the new generations and many works (5)(6) have already been carried out on the research and development of new solders. New lead-free solders are expected to have some requirements, for example, moderate melting temperature, proper strength and integrity, and lower prices, as compared with conventional solders. There have been already several alloy systems developed. Among ·these alloy systems, tin-bismuth binary or tin-bismuth-silver ternary alloys have great advantages such as having a wide range of soldering .temperature by controlling con:ipositions, though they have such disadvantages as ""lift-off"" (7)-(9): It is said, on the other hand, that a frequently overlooked property of solders, or one that is typically ignored by the research scientist as an ""issue"" for the manufacturing or product engineer, is wettability (10), although a ·work on the wettability has recently been published (11). In this Work, therefore, the authors selected Sn-Bi-Ag solders and focused mi the effect of Ag-addition to wettability of the solder."

Jan 1, 2000

By Cz. Mazanek

Specific biostimulating and anticancerous properties have been observed in peat, Ash Vacanta, and in an amorpous silica that is obtained as a by-product of alumina production from Turow clay in Poland. The anmphous silica was characterized and found to have a large specific surface area. This property may account for the beneficial characteristics of the material.

Jan 1, 1989

By Carlos Maurício. F. Vieira, Lázaro A. Rohen, Sérgio N. Monteiro, Rafael G. de Castro, Gustavo X. Borges, Maycon A. Gomes, Frederico M. Margem, Anna C. C. Neves

Economic and environmental benefits are motivating studies on natural fibers, especially lignocellulosic extracted from plants, have been studied to substitute synthetic fibers, such as glass fiber as reinforcement in polymer matrices. By contrast to synthetic fibers, natural fibers have the disadvantage of being heterogeneous in their dimensions specially the diameter. About the hemp fiber, little is known of their dimensional characteristics. The aim of the present work was to statistically characterize the distribution of the diameter of hemp fibers. Based on this characterization, diameter intervals were set and the dependence of the tensile strength of theses fibers with a corresponding diameter was analyzed by the Weibull method. The diameter was measured with precision using a profile projector. Tensile tests were conducted on each fiber obtain mechanical strength. The results interpreted by Weibull statistical showed a correlation between the resistances of the fiber to its diameter.

Jan 1, 2015

By Jewel A. G. Gomes

Lead has long been an USEPA priority pollutant and an important environmental and health concern because of its toxicity at ppb levels. In light of health and exposure data for lead, the EPA has set standards for Maximum Contaminant Level (MCL) and a MCL Goal (MCLG) as 15 ppb and 0 ppb, respectively. An accurate and rapid measurement of lead in the field remains a technical challenge. In this work, a relatively new method of deploying a nanoband electrode system using anodic stripping voltammetry has been optimized by changing deposition potential, electrolyte, and plating time used for the measurement of Pb(II) in water samples. Green rust has been proven to be an efficient intermediate matrix for removal of lead contaminants. We also report here the removal efficiency of lead using green rust produced by electrocoagulation, both directly and indirectly. Lead containing floc was also characterized through XRD, SEM, and EDAX techniques.

Jan 1, 2008

By Kazuyuki Kakegawa

"Sintered body of lead zirconate titanate (PZT) was prepared through the spark plasma sintering (SPS) technique. When the mixture of raw materials was calcined at 800°C and sintered at 900°C for 10 min. with SPS technique, the sintered body had almost theoretical density but was a mixture of lead titanate (PT) and PZT. When a calcining temperature of 1100°C was employed, sintered body had a single PZT phase but a lower density. High dielectric constant was obtained for a sample calcined at 800°C, sintered with SPS tecbriique and fired again in the air at 1100°C.IntroductionSpark plasma sintering (SPS) is a recently developed technique for sintering metals and ceramics1. The scheme of SPS is shown in Fig. 1. Sample is put in a graphite die in a vacuum chamber. It is pressed and pulse voltage is applied. The electric current heats the die. It is said that the pulse causes a spark-plasma between particles in the sample. Because of the spark- plasma, sample can be sintered at temperatures lower than that in the ordinary sintering by several hundred degrees of Celsius. The sintering period is also very short2Low sintering temperature and short sintering period in SPS technique cause low reaction rate. It is both disadvantage and advantage. In some cases, the reaction cannot be completed under the SPS conditions. If a mixture of several compositions having different properties can be sintered without a compositional change by the diffusion during the sintering, combination of properties, and therefore a design of property will be possible3. The low reaction rate of SPS may enable such combination."

Jan 1, 2000

By Xiangru Chen, Qijie Zhai, Haicheng Li, Chao Yang, Zhang Wei

The Nb-rich phase generated by the addition of trace amounts of Nb(<0.1wt%) \ and the effects of different content of Nb on the morphology and distribution of graphite in ductile iron were studied in this paper. The results showed that when the content of niobium less than 0.1wt%, the two-dimensional morphology of Nb-rich phase existed in microalloyed ductile iron were mainly regular pattern such as square, triangle, polygon etc. Besides, Nb-rich phase in large size distributed in the matrix with a certain distance from graphite. With the increasing amount of niobium, the dispersion degree of graphite diameter, average diameter and roundness increased slightly, and the number of graphite decreased slightly.

Jan 1, 2015

By Thomas J. Keefe, O&apos

The effects of cobalt, B-naphthol, glue and antimony on the polarization behavior of zinc sulfate electrolyte were investigated. It was found that B-naphthol was beneficial in reducing the detrimental effects of cobalt while antimony and excess glue were each harmful. Since the nu cl eat ion over potential was insensiti1ve to coba1t, other regions of the polarization curve were used to indicate electrolyte balance. The low? current density area occurring in the reverse or anodic sweep direction was? often an indicator when an ?unstable condition existed. The two parameters evaluated were the degree of inflection in the polarization curve in the low current density region during scanning and the rate of current rise observed when the sample was potentiostated at -0.781 Volts (SHE). Using this technique, a two-additive system was shown to be desirable to control cobalt and antimony containing electrolytes. The structure of the deposits was examined using scanning electron microscope techniques.

Jan 1, 1985

By Sung Jin Han

Magnesia-based refractory is generally used in an electric arc furnace (EAF) due to its relatively high corrosion resistance and strength at high temperatures. However, the magnesia refractory is attacked by EAF slag and thus the lining life continuously decreases. Thus, it is significant to identify the interfacial reaction between magnesia refractory and FeO-rich EAF slags. In the present study, the influence of FeO-rich slag on the corrosion behavior of MgO refractory was evaluated. The (Fe,Mg)Oss layer was observed at the slag-refractory interface and its thickness increased with increasing content of FeO in the slag. The specific reaction phenomena and formation behavior of (Fe,Mg)Oss layer were evaluated by thermochemical computing program, FactsageTM7.0.

By P. Chris Pistorius

"Ilmenite smelting involves partial reduction of iron oxide from a slag consisting mainly of T1O2, T12O3 and FeO, yielding as products iron (with approximately 2% carbon) and titanium slag. Slag purity requirements preclude any fluxing additions, and the aggressive nature of the slag necessitates a furnace freeze lining. Large departures from thermal and chemical equilibrium hold in the smelter, with possible implications for process stability. The slag is approximately 150K. hotter than the metal, which means that the metal temperature is below the slag melting point; this difference in temperature has been shown to lead to formation of a solid TisOs-rich layer between the slag and metal. Recent equilibrium measurements have confirmed that the slag and metal are not in chemical equilibrium either, with significantly more reducing conditions in the metal than in the slag. After solidification, the pseudobrookite slag structure is metastable below approximately 1400K, and may transform upon slight oxidation.IntroductionThe natural mineral ilmenite is the main source of titanium, which is mainly used to produce Ti02-based pigments. Ilmenite has the ideal formula FeTiC>3, but natural minerals can be partially oxidized (to contain some Fe3+), and typically contain MnO and MgO as well, together with associated silicate minerals. Smelting is one of the methods to upgrade ilmenite for subsequent T1O2 pigment production; smelting involves partial reduction of FeO to form metallic iron as a byproduct and titanium slag as the main product. Reduction is typically controlled to yield a slag which contains around 10% FeO, 85% (Ti02+Tij03) and 5% impurity oxides (mainly MnO, AI2O3 and S1O2). An example of a typical average slag composition from reduction of South African ilmenite is shown in Table I. As this indicates, a significant side reaction is reduction of some T1O2 to T12O3. The relative extents of reduction of FeO to Fe and of Ti02 to T12O3 are such that the slag stoichiometry is close to that of the pseudobrookite phase [1]. Pseudobrookite has the structure AB2O5 (where ""A"" and ""B"" are different cation sites); the phase which makes up the bulk of solidified titanium slag has the AB2O5 structure and stoichiometry [2], and can be viewed as a solid solution of FeTi20s, T13O5, ÌçÔÀ2è5, MgTi20s, AI2T1O5 and C^TiOs [1]. This solid-solution phase is referred to as ""pseudobrookite"" or ""M3O5"" in this paper."

Jan 1, 2012

By Sergio Bustos

Covellite resulting from an original 0.5 % Cu(tot) chalcocite ore has been leached in columns at different temperatures, in the lower range of 10 - 20 °C, under acid - ferric bacterial leaching conditions. Dissolution of copper from covellite depends on the rate and extent of sulphide oxidation by ferric ion. While it is recognised that the dissolution of sulphide minerals is electrochemical in nature, an apparent chemically controlled dissolution pattern was measured with activation energy of 78.09 kJ/mol (18.66 kcal/mol). Ferric iron is the main oxidant and its production and availability will depend on the bacterial activity developed in the system. This activity is characterised by the population size and by the specific oxidation rate of the bacteria. Bacterial growth was followed directly by the number of bacteria appearing in the column effluent solutions and indirectly by the generation of ferric iron or by the total oxidation observed in the columns. These results have been interpreted by using the heap oxidative capacity parameter, which indicates an equivalent ferric production of about 0.07 - 0.15 kg Fe +3/t/day at 20°C. Although bacterial activity decreases to about 0.03 kg Fe +3/t/day with decreasing temperature, a significant bacterial oxidation is still observed at 10 °C. However, extended lag times are observed, which delay the start of bacterial growth to times concurring with covellite leaching. Under these conditions, bacterial activity is displayed through a population controlled by the rate at which- ferrous iron is released from the reducing covellite surface. These results suggest the potential benefit of including some kind of inoculation when operating at lower temperatures. Also, heat loss control and/or heat addition to the heaps should be considered during process design and operation of ferric bacterial heap leaching of secondary copper sulphide ores at temperatures lower than 20°C.

Jan 1, 1999

By Srinath Viswanathan, Zhijing Zhang, Ramana G. Reddy

"The viscosity measurements were carried out on melts of 380 aluminum alloy containing 20 volume % SiC particulates under various shear rates at different temperatures using a Brookfield viscometer. Results showed that viscosities of the melts increased with decreasing temperature and decreased with increasing shear rate. These results were compared with those of 356 alloy and it was found that the temperature had a more significant effect on viscosity of 356 alloy than that of 380 alloy containing SiC particulates. Based on the present experimental data an empirical viscosity model, which considers the effects of both solid fractions in the melt and shear rate, is proposed.IntroductionDiscontinuously reinforced metal matrix composites materials (MMCs) such as aluminum alloy containing SiC particulates have considerable potential for applications in the automotive industry because of their superior stiffness, higher specific mechanical properties, better dimensional stability and strength retention at elevated temperatures when compared to their monolithic counterparts. They have a great advantage in the specificity of their properties, meaning that specific materials can be engineered for specific applications. With such freedom of design, materials engineers have to accumulate a very large database of mechanical properties. Among these properties, the viscosity of alloy slurries is very important for producing, casting and forming process of metal matrix composites materials because viscosity has a decisive influence on fluid flow. The understanding of the rheological behavior of alloy slurries is necessary for these materials to become economic reality. Therefore, a study was carried out to measure the viscosities of 380 aluminum alloy containing 20 volume % SiC particulates under various shear rates and temperatures. In addition, a viscosity model representing the primary features of the alloy slurries was developed."

Jan 1, 1999

By Rikiya Kamezawa, Rudiono, Manabu Takeuchi

"Schottky type solar cells based on phthalocyanine (Pc) thin films were fabricated, and their photovoltaic performance was investigated in various ambient atmospheres. Most of cells prepared in this study showed a good rectification and photovoltaic effects in the visible wavelength region. The introduction ofN02 gas into the measuring chamber was confirmed to increase the current both in dark and under light illumination. However, chemical reaction between the Al electrode and N02 formed some oxide and deteriorated the Schottky barrier, resulting in an increase in cell resistivity. SF 6 gas also showed similar effects on the cell performance.IntroductionPhthalocyanine is one of the typical organic semiconductors, which shows high photoconductive sensitivity in the visible to infrared region. Today, several kinds of metal phthalocyanines are used in electrophotographic photoreceptors. In addition, application of phthalocyanines to solar cells have also been trying by many workers [1, 2]. Many efforts have been made for improving performance of phthalocyanine solar cells by modification of device structure [3, 4], doping by dye or pigment [5, 6] and incorporation of metal clusters [7]. It is known that electrical conductivity in phthalocyanine is increased by adsorption ofNO2 [8, 9]. We tried to improve photovoltaic performance ofphthalocyanine solar cell by adsorption ofNO2. This paper describes the influence of N02 adsorption on the photovoltaic behavior of phthalocyanine solar cells."

Jan 1, 2000

By Zhijing Zhang

Sodium borosilicate is the basic composition of coating materials, Vycor and Pyrex glasses. In the present study, viscosities of Na2O-Si02-B2O3 ternary melts were measured under various compositions and temperatures. Experiments were carried out using rotary viscometer and graphite components. Our experimental results were compared with those in literature. Based on present experimental results, the previous structure based viscosity model was modified. The predicted viscosity results are in excellent agreement with the present experimental data in the temperature range with molten state samples. The fitting ranges of the model cover the composition of XB2O3 from 0.1 to 0.6 combined with xSio2 / xNa2O = 0.5, 1,2 and 5 respectively.

Jan 1, 1998

By T. Alboussiere, O. Paireau

"We have designed an experiment to simulate natural convection in a direct-chill aluminium ingot. In this experiment we induce natural convection within a hemisphere filled with liquid-metal (mercury). The device consists of a copper hemispherical bowl closed by a copper plate. The top is maintained at superheat temperature while the boundary is cooled. While the temperature measurements were found using thermocouples, the velocities were obtained using an original technical procedure that relies on MHD properties. By applying a steady local magnetic field, we measure the velocity. The distribution of temperature and velocity can be separated into a thermally stratified core bounded by thermal wall jets. These wall jets greatly influence the degree of macrosegregation in ingots.1. Natural Convection in Aluminium CastingIt is well known that the quality of the final product in aluminium casting depends on the movements within the liquid metal such as forced or thermogravitational convection. Strong buoyancy-driven flows are known to occur in the liquid metal pool of an aluminium ingot caster. These flows have a significant influence on the metallurgical structure of the ingot through the redistribution of heat, fragmented dendrites and segregated material within the pool. Macrosegregation mechanisms depend on favourable temperature and flow distributions in the sump, and these factors will determine the pattern and degree of macrosegregation. Moreover, for many years, the importance of thermally-driven natural convection in casting has been underlined (Cole & Bolling, 1965). In this way, a precise determination of the velocity and temperature fields is required in order to improve understanding of the macrosegregation mechanisms. That is precisely the aim of this paper, which provides experimental data of the flow and the temperature distributions in a natural convection experiment. We intend, with this laboratory experiment, to determine accurately the velocity field, particularly within the thermal boundary layer where the effects of the flows may have an important role in the transport of crystals."

Jan 1, 1999

By V. Baltazar

The behaviour of arsenic and antimony during copper electrorefining was studied in order to identify the conditions under which good quality copper cathodes could be produced from anodes with high levels of these impurities. Examination of the effect of current density over the range 21 to 37 mA/cm2 indicated that the relative amounts of As and Sb entering the electrolyte affected the onset of passivation. When the ratio of As/Sb entering the electrolyte was greater than 2, the anodes showed no sign of passivation even at the highest current density; when the ratio was less than 2, the anodes passivated at 37 mA/cm2. Cathode analyses showed that anodes with an As/Sb dissolution ratio less than 2.0 tend to produce cathodes of inferior quality even at normal current densities (25.7 mA/cm2). The criterion of a minimum As/Sb dissolution ratio of 2.0, and mathematical correlations for the distribution of As and Sb between the electrolyte and slime developed in a previous study, allow the calculation of the maximum allowable Sb level in en anode for a given As concentration. Analyses of plant data at the CCR Division of Noranda Inc. for the last four years of operation have demonstrated that the use of this as a quality control tool has allowed the quality of copper cathodes to be maintained despite a significant increase in the average Sb levels in anode receipts.

Jan 1, 1987

By June-Yong Eom, Jong-Jin Pak, Jung-Mock Jang, Min-Kyu Paek

The nitrogen solubility in liquid Mn-Si, Mn-Si-Fe, Mn-Si-C and Mn-Si-Fe-C alloys has been measured by the gas-liquid metal equilibration technique in the temperature range of 1673-1773 K. The additions of silicon, iron and carbon significantly decreased the nitrogen solubility in liquid manganese alloys. The experimental results were thermodynamically analyzed by the Wagner’s formalism to determine the first- and second-order interaction parameters of silicon, iron and carbon on nitrogen in liquid manganese. The thermodynamic parameters can be used to predict the nitrogen solubility in ferromanganese and silicomanganese alloy melts as functions of the melt composition and temperature at given nitrogen partial pressures.

Jan 1, 2014

By M. Nilmani, J. Sofra

The transverse distributions of the solids discharge velocity and mass flux at the discharge end of vertical and inclined lances were measured in order to detennine the transverse distributions of the axial momentum flux, which is a dominant factor influencing the penetration behaviour of particles into melts during submerged injection. The effects of gas velocity (10 - 30 m/s), solids loading (5 - 10), lance length (0.15 - 1.0 m), lance inclination (vertical downward - horizontal) and particle density (2500 - 8900 kg/m3 ) were investigated, while the lance diameter and particle size were fixed at 10 mm and 220 µm respectively. The particle velocities and mass fluxes were measured by image analysis of particles illuminated in a laser-generated light sheet aligned vertically through the axis of the lance at the discharge point. The particle discharge velocity profiles for vertical downward flows were synunetrical about the centre-line of the lance, with the maximum velocities occurring at the centre-line. The velocities increased with increasing gas velocity, increasing lance length and decreasing particle density in accordance with previous observations. The transverse mass flux profiles were also synunetrical for vertical downward flows, however at the lower gas velocities the peaks in the profiles were displaced from the centre-line of the lance by a fractional diameter of about 0.15. The particle discharge velocity profiles become increasingly asynunetric as the lance orientation was changed from vertical to horizontal, with higher particle velocities present near the top wall of the lance. The mass flux profile also became asyrrunetric as the horizontal orientation was approached, however in this case, the profile became biased towards the bottom of the lance. The effect was much more pronounced for a gas velocity of 10 m/s than for 30 m/s, showing the relatively stronger gravitational influence as the velocity was reduced.

Jan 1, 1996

By Zhijing Zhang

Long-term thermal stability of ionic liquids is essential for reliable performance of ionic liquids in any engineering applications. TGA studies were carried out on a series of ionic liquids with different cations and anions such as 1-butyl-3-methylimidazolium chloride ([C4mim]Cl), 1-hexyl-3-methylimidazolium chloride ([C6mim]Cl), 1-hexyl-3¬methylimidazolium tetrafluoborate ([C6mim]BF4), 1-hexyl-3-methylimidazolium hexafluorophosphate ([C6mim]PF6), 1-octyl-3-methylimidazolium hexafluorophosphate ([Csmim]PF6), and 1-butyl-3-methylimidazolium bis(trifluromethanesulflonyl)imide ([C4mim][Tf2N]). The short-term thermal stability of ionic liquids was evaluated by measuring the onset temperature of decomposition of ionic liquids, and the long-term thermal stability of ionic liquids was also evaluated by weight loss of ionic liquids over a long period of time at various temperatures. The experimental results showed that the long-term thermal stability of ionic liquids decreased with increasing temperature and was significantly lower than the onset temperature of decomposition of ionic liquids.

Jan 1, 2002

By James A. Warren

The phase field method has been successfully employed as both a tool to model heterogeneous materials and as numerical method for calculating the motion of interfaces and phase boundaries without explicitly tracking those interfaces. The method has been used to model a diverse suite of problems describing the microstructural evolution in materials. These models are derived from thermodynamic arguments and symmetry principles, and usually guarantee positive local entropy production for systems out of equilibrium. Descriptions of how phase field methods can be applied to the problems of solidification, grain growth, and electroplating will be presented.

Jan 1, 2001