Search Documents

By Han Ilhan

This paper discusses and describes aspects of a cost effective and safe tailings impoundment selection. In light of the current low metal prices and recent tailings embankment failures around the world, it is becoming extremely more important to develop tailings impoundment design that balance cost efficiency with safety. The paper will present critical design components associated with a tailings impoundment which need to be addressed during the planning phase. Procedures for identifying various tailings impoundment alternatives, and evaluation and selection of alternatives are presented.

Jan 1, 1999

By P. R. Bruggink

"A quantitative tool has been developed to assess the impact of changes in recycling rates on the environmental impact of aluminum supply. It has been applied to the USA to forecast sources of aluminum scrap and to examine the impact of an increase in Old Scrap recovery on the USA supply system and the subsequent effect on the Life Cycle Impact of aluminum supply. The reported data for primary, secondary and import/export supply and product shipments for aluminum in the USA show a fairly good balance between supply and demand on average over the years. Therefore, it is reasonable to use the data, along with published estimates of average product lives, recycling rates and recoveries to draw conclusions about future aluminum scrap generation· and recovery. The Life Cycle Impacts of increasing post-consumer recovery rates to recover an additional 450,000 MT/yr (1 billion lb/yr) has been estimated using the model.The spreadsheet model upon which this work was based was developed in U.S. Customary units. Converting the figures to Metric units would have required converting the entire model and rebuilding the figures. I have chosen to leave the figures in U.S. Customary units. I apologize for any inconvenience this may cause."

Jan 1, 2000

By R. M. Luna-Sánchez

Electrochemical studies, particularly Evans? diagrams, have been employed in hydrometallurgy to simulate and explain the redox phenomena that take place at mineral and metal surfaces during operations such as leaching and cementation. However, despite their utility, in some cases, the combination of the cathodic and anodic branches, determined separately, does not reproduce the chemical environment present when both processes occur simultaneously on a specific surface. In the present paper, limitations of Evans? diagrams are analyzed through two examples: silver sulfide cyanidation and gold cementation on zinc. In both cases, the surface kinetics are sensitive to the local pH and cyanide levels. When the electrochemical oxidation of silver sulfide or the reduction of gold are performed in the absence of its corresponding redox reaction, the local pH obtained does not simulate the real situation and the combined reaction kinetics may be very different from those determined from the Evans? diagrams.

Jan 1, 2003

By Sheng-hai Yang

The electrochemical synthesis was conducted in anhydrous ethanol solvent mixed with conductive reagent when tantalum plate was used as anode and stainless steel plate as cathode. The effects of different conductive reagents (such as NH4Br, (CH3)4NCl, (C4H9)4NCl), conductive reagent concentration and the space on the cell voltage and the current density were investigated. The current efficiency of electrosynthesis was more than 95%. The electrolyte, a mixed solution was then undergone air distillation and vacuum distillation to get the final product which was characterized by Fourier Transform Infrared(FTIR) spectroscopy, Raman spectra, 1H-Neclear Magnetic Resonance(1H-NMR) spectroscopy. Carbon and hydrogen contents in the product were determined by elemental analysis instrument. Results consistently show that the product was tantalum penta-ethoxide.

Jan 1, 2006

By Hong Yong Sohn

On the occasion of this symposium in my name, I reflect upon the contributions of my academic mentors and early associates who helped shape my professional career. I was fortunate to have these people around me during my graduate work and at the start of my professional career. In forming my view of the technical field and career, they represented academia, research institutions, industry, and different parts of the world.

Jan 1, 2006

By Mala Nath, Atjit Mallick, Asheesh Kumar

"The present research work is aimed to focus on the development of chemically stable light weight microporous carbonaceous material, such as activated charcoal incorporated either with titanium n-butoxide, titanium diisopropoxide bis(2,4-pentanedionate), vanadium 2,4-pentane-dionate or zinc 2,4-pentanedionate having varying wt% of the metal (2-8%) using ethanol as solvent at 40--50 oC followed by calcinations at 100, 150 and 200 cC, except the samples with titanium diisopropoxide bis(2,4-pentanedionate) which are calcinated at 80 oC. Atomic absorption studies along with FESEM revealed that the maximum incorporation of metals (Zn, V and Ti) in activated charcoal was observed with 4 wt% of zinc 2,4-pentanedionate calcinated at 150 oC , 4 wt% of vanadium 2,4-pentanedionate at 100 oC, 2 wt% of titanium n-butoxide at 100 oC and 2 wt% of titanium diisopropoxide bis(2,4-pentanedionate) at 80 oC, and equilibration time of 20-24 h was used in each case. Hydrogen sorption behavior in these carbonaceous materials has also been studied at 77.4 K and low pressure up to I bar. The highest hydrogen uptake obtained was 1.45 wt% (164.5 cm3 (STP)/g at P/Po = 1.0) for activated charcoal incorporated with 4 wt% of zinc 2,4-pentanedionate calcinated at 150 oC.IntroductionTwo of the major challenges for humanity in the next twenty years are the shrinking availability of fossil fuels, the global warming and potential climate changes that result from their ever-increasing use. So it is necessary to fmd an energy source that is convenient, flexible and controllable. One possible solution to these problems is to use an energy carrier such as hydrogen, and ways to produce and store hydrogen in electric power plants and vehicles. Hydrogen storage is the bottleneck for the breakthrough of hydrogen as energy carrier in automotive applications [1]."

Jan 1, 2012

By E. Yegan Erdem, Fiona M. Doyle, Alyssa A. Maich

"There is an expanding interest in synthesizing high quality magnetic nanoparticles, most notably for biomedical applications. Different processing routes have been reported for the synthesis of magnetite and maghemite. However, some ambiguity remains on their precise chemistry, intermediates, and final products, due to the structural similarity of maghemite and magnetite, and the relative ease of redox transitions during synthesis. Here we present the results of TEM, x-ray and electron diffraction, and SQUID studies aimed at characterizing the products from two different reaction systems, thereby clarifying the reaction chemistry. The first system hydrolyzed aqueous FeCh and FeCb chlorides with ammonia in a micro fluidic reactor at ambient temperature; although the reaction product displayed a uniform distribution, it included non-magnetic goethite and lepidocrocite. If the aqueous solutions contained dissolved oxygen, there appeared to be extensive oxidation of Fe(II). The second system thermally decomposed iron (III) acetylacetonate in ether. In prior studies, oleylamine has been reported to serve as both a reducing agent and capping ligand to control particle characteristics; however, our studies revealed little reduction, with maghemite dominating the reaction products.IntroductionMagnetite and maghemite nanoparticles are co=only used in ferrofluids, in medical applications, and in drug delivery. Superparamagnetic properties, along with low cytotoxicity, colloid stability and bioactive molecule conjugation capability, make these nanomagnets ideal for both in-vitro and in-vivo biomedical applications [1]. One of the major constraints on widespread adoption of nanoparticles for these applications is the amount needed. Typical batch synthesis methods produce polydispersed nanoparticles, which require further size selection procedures to isolate the mono disperse nanoparticle population needed for many applications. In order to maximize the yield of usable particles from a synthesis operation, the reaction conditions must be closely controlled. This requires full knowledge of how the reaction conditions control the various aspects of nanoparticle growth. Many methods have been used to synthesize iron oxides, including sonochemical reactions, mechanochemical synthesis, hydrolysis and thermal decomposition. This work examines the latter two methods, focusing on oxidation and reduction of iron."

Jan 1, 2012

By R. M. Nadkarni

This paper examines the broad' economic parameters of copper smelting by conventional and new smelting technology. Location, transportation of products to market and pollution control options are discussed.

Jan 1, 1983

By Maria G. Alves, Alexandre M. Stumbo, Francisca M. A. Pinheiro, Jonas Alexandre, Sergio N. Monteiro, Valdo da S. Marques, Paulo R. N. da Silva

"Brazil is among the few countries with potential for developing all sources of renewable forms of energy. In particular, the country is leading the world efforts of substituting petroleum based fuels for biofuels, such as ethanol and biodiesel. Most of the Brazilian petroleum, which has now achieved self sufficiency, is extracted from offshore wells located at the north region of the state of Rio de Janeiro. In view of the future depletion of petroleum, the State University of the Northern Rio de Janeiro (UENF) has created a Center for Alternative Energies (NEAL) to carry out R&D programs on renewable forms of energy. Today, the main project of the NEAL/UENF is a model park for generation of renewable forms of energy. The objective of this work is to present the structural concept of the park and discuss its contribution in terms of scientific, technological, economical and environmental benefitsIntroductionEnergy is presently a key issue in the world agenda for sustained development and environmental protection. It is of common agreement that the existing status of increasing use of fossil fuels, mainly petroleum, natural gas and coal will not only cause depletion of these resources with a consequent elevation in price but also climate changes, especially global warming. In fact, the humankind may be already facing an irreversible situation of climate alterations as well as reduction of conventional sources of energy. The worse predictions foreseen by specialists, still for this coming century, are dramatic disasters due to catastrophic weather in association with a profound energetic crisis. This scenario may, however, be avoided by actions that could effectively tackle the core of the problem. These actions have been suggested and discussed by scientists and leading authorities, especially in international symposia [1-3]. In particular, the Kyoto Protocol proposed goals for reduction of greenhouse gas emissions as well as a mechanism of carbon credits to allow for decreasing CO2 content in the atmosphere without affecting industrial production [3]."

Jan 1, 2008

By Matthew Tunnicliffe, Akram Alfantazi, Paul Nesbitt, Farzad Mohammadi

"Lead and its alloys are proper candidates for anodes in electrowinning processes mainly because they are insoluble in the leach solutions and relatively cheap. However, the annual cost of corrosion problems associated with these anodes is millions of dollars. In this study lead-silver and lead-calcium anodes were tested under typical nickel electrowinning conditions and the effect of chloride on the corrosion performance of the anode materials was investigated. Corrosion rates of the anodes were calculated using the discharge plateau (reduction of lead dioxide to lead sulfate) after galvanostatic experiments. It was found that lead calcium anodes have the highest corrosion rate both in the presence and absence of chloride. Surface morphology of the electrodes was studied using SEM and the corrosion products were characterized using XRD.IntroductionLead (Pb) is usually the preferred material for commercial anodes since it is insoluble in the leach solution and the costs are manageable. One advantage of using an insoluble material as an anode is the higher purity of the cathodic deposits and better quality of the end product. During nickel electrowinning, metallic nickel is deposited on the cathode while oxygen evolution reaction (OER) takes place on the anode. In practice, relatively high potentials are necessary for the reaction to proceed at the desired rate because of the high overpotential of OER on lead. Lead anodes get oxidized in typical electrowinning conditions and usually have two to three years of lifetime. Although the price of each anode is insignificant, the overall cost of corrosion of these anodes is considerable, which is due to the large number of anodes used in a plant, typically two to three thousand. Therefore, corrosion is a significant problem associated with lead anodes in commercial nickel electrowinning plants and industries show interest in addressing this problem. Corrosion of lead electrodes in acidic environments has been previously the subject of many research studies [I-7]. It has been reported that, during the anodic polarization of lead, several phases may be present on the surface, depending on the potential range that is being studied [8]. Lander showed that lead is oxidized at potentials higher than 0.252 YsHE with tetragonal lead monoxide being the main reaction product [9]. At 0.666 YsHE lead can transform to lead dioxide; however, it is not stable and transforms to lead sulfate and lead oxide. At potentials higher than 1.684 YsHE, lead dioxide is eventually a stable phase and forms a protective layer on the surface [I 0, 11]. Under conditions of a typical nickel electrowinning plant, usually a 200 A/m2 current density is passed through the electrodes."

Jan 1, 2012

By T. T. Chen

Secondary copper anodes are generally rich in Sn, Pb, Ni and Sb, but are notably deficient in Se, Te and Ag. In the secondary copper anodes, most of the Ni, virtually all of the Ag, slightly more than one-fifth of the Pb, about one-third of the As and Sb, and approximately one-tenth of the Sn are in solid solution in the copper. The remaining impurity contents occur as 1-5 µm grain-boundary inclusions in the anodes, and these are mainly Cu2O, SnO2, Cu-Pb-As-Sb-Bi oxide, Pb-Sb oxide, Sn-Ni-Zn oxide, Cu-Sn-Ni oxide, Cu-Sb-Ni oxide (Kupferglimmer) and trace Cu2(Se,Te). Barium sulphate, which originates from the mold wash used in casting, is also present in the anodes. During electrorefining, the BaSO4, SnO2, Pb-Sb oxide, Sn-Ni-Zn oxide, Cu-Sn-Ni oxide and Cu- Sb-Ni oxide inclusions are liberated and accumulate in the slimes layer. Solid solution Ni dissolves and the Ni accumulates in the electrolyte. Solid solution Sn and Pb dissolve, but partly reprecipitate as Sn arsenate and PbSO4, respectively. Solid solution Ag dissolves but rapidly reacts to form Ag2(Se,Te), Ag powder, Ag-bearing Cu2O, (Cu,Ag)SO4 or a complex oxidate phase. Partial dissolution of the Cu-Pb-As-Sb-Bi oxide particles takes place; the Pb component is converted to PbSO4, whereas Cu, As, Sb and Bi dissolve. The reacted particles retain the morphology of the original Cu-Pb-As- Sb-Bi oxide phase. Some of the solubilized As, Sb and Bi remains in solution, but much reprecipitates as SbAsO4, As-Sb-Bi oxide, and as a poorly defined oxidate phase which consists mostly of Cu-Ag-Pb arsenate-sulphate. The high Sn contents of secondary copper anodes do not seem to affect the behaviour of the anodes during electrorefining.

Jan 1, 1999

The presence of clay adversely affects the floatability of copper and molybdenum during processing porphyry copper/molybdenum ores. In addition, reagent consumptions are much higher than when treating clay-free ores. Ores containing kaoline, brammollite, illite and montmorillonite were examined in the laboratory to determine how clay minerals affect the floatability of copper and molybdenum, and to find a possible solution to alleviate the harmful effect of clay slimes. It was demonstrated that the presence of clay mostly affects floatability of coarse and middling particles, and reduces selectivity. The results of the research work showed that there may be several possible ways of reducing the detrimental affects of clay slimes on flotation, some of which include a) use of alternative flowsheets, b) flotation at reduced pulp density, and c) the use of special frothers. The applicability of the findings in plant practice are discussed.

Jan 1, 1999

By Tong Deng

Clean processing of copper converter slags for reclaiming cobalt and copper could be a challenge. An innovative and environmentally benign approach for recovering metal values from such a slag was developed in the present work. Curing the slag with sulfuric acid, without re-smelting or roasting as currently practiced in the industry, made it amenable to leaching, and more than 95% of the cobalt and up to 90% of the copper was extracted, together with iron, by water leaching, leaving silica behind in a residue. Copper in the leach liquor was recovered by cementation with iron, and the dissolved iron crystallized as ferrous sulfate monohydrate. Cobalt in the pregnant solution rich in iron was recovered by either cementation or sulfide precipitation. Chemical and mineralogical characterization of the slag and its products were examined and compared to determine the nature of the changes occurring during curing and leaching. Operating variables were also investigated and optimized.

Jan 1, 2003

By A. Alvarez

In this work, mesophilic and thermophilic cultures have been used in the presence of silver as a catalyst. Chalcopyrite and byproducts of bioleaching were characterized in order to: a) obtain information about the kinetics control of the process, and b) explain the different behaviour observed during the mineral attack. With thermophilic microorganisms (68°C and Norris medium as nutrient) the reaction stopped at approximately 65% copper extraction, with and without Ag ion addition as a catalyst. The remaining chalcopyrite appears surrounded by hydronium jarosite (with ammonium ion in substitution in the "alkaline site"), goethite and elemental sulphur. With mesophilic cultures (35°C and 9K medium as nutrient) the reaction stopped at approximately 25% copper extraction (without Ag) and approximately. 85% extraction (with Ag). In both cases, the remaining chalcopyrite was surrounded by agglomerates of ammonium jarosite (with hydronium ion substitution in the "alkaline site") and some iron oxides and/or hydroxides.

Jan 1, 1999

By John A. Gisby

Phase equilibria for multi-component systems can be calculated reliably from critically assessed thermodynamic data for sub-systems using software packages like MTDATA, developed by the National Physical Laboratory, UK (NPL). Models and data resulting from an ongoing Mineral Industry Research Organisation (MIRO) project make such calculations possible for the complex systems encountered during sulphide smelting, involving interactions between matte, slag, metal, and gas phases. Predictive calculations can be made that are directly relevant to industrial processes, covering composition and temperature ranges beyond the scope of hard- copy phase diagram compilations, allowing the feasibility of more economic and environmentally sound routes to be explored, better choice of materials to be made, and pilot plant studies to ,be directed more efficiently. Current applications include the selection of suitable fluxing practices in copper and nickel smelting, analysing the operation of the Kennecott copper smelter, optimising the recovery of precious metals and investigating refractory wear.

Jan 1, 2002

By Corale L. Brierley

Bioheap leaching, commercially applied for secondary copper ores and agglomerates, is rapidly gaining popularity. Bioleaching of chalcopyrite concentrates is imminent. Copper bioheap leaching encompasses the bioleaching of acidified and agglomerated coarse, secondary copper ore, stacked on permanent or on/off pads. The stacked ore is irrigated with raffinate containing bacteria. LME-grade cathode copper is produced by SX/EW. Low capital and operating costs, rapid start-up, environmental benefits, operational simplicity and a good performance record make bioheap leaching an attractive technology. This paper looks at the state-of-the-art of copper bioheap leaching and chalcopyrite concentrate leaching, the risks, the benefits, costs, bioheap performance and the future prospects of copper bioleaching.

Jan 1, 1999

By F. Sakurai

The enlarged Mitsubishi process in Naoshima has been in steady operation since. May 1991. However, the sulfuric acid plants have been in operation for more than 30 years. The acid plants were modernized between 1999 and 2001 by renewing some of main equipment such as the drying tower and gas heat exchangers, and introducing new technology. At the same time, as an electric energy saving measure, the electric power consumption in the sulfuric acid plant was vastly improved by decreasing the volume of gas treated the installation of low temperature activity catalyst in the 1st pass of the converter and optimization of main gas blower runner. Furthermore, last year, the oxygen plant was replaced and enlarged, and anode production increased from 240,000 to 280,000 tonnes per year with an associated increase of sulfuric acid from 550,000 to 660,000 tonnes per year. This paper describes these recent improvements in the acid plant at Naoshima smelter.

Jan 1, 2002

By Alpagut Kara

Turkey is the fifth biggest ceramic tile exporter in the world. Considering the expectation that the Turkish tile sector continues to expand, further studies both on the improvement and the development of tile formulations are necessary in order to make the producers advantaged in the world market while maintaining the capital and running costs at reasonably competitive levels as well. In addition to such studies, waste management in tile manufacturing has also recently become an important issue. Accordingly, the industrial use of wastes in the traditional ceramic industry has been intensively investigated in the recent years. This work describes part of a detailed research project carried out jointly on the possible re-use of muds (raw production waste) from glazing and pressing lines of a local tile company in the development of new wall and floor tile formulations. In order to achieve this, the waste material was firstly investigated in function of chemical and mineralogical compositions. Then, the particular focus was given to the presence of the waste material in increasing amounts on the thermal behaviour and physico-mechanical properties of the re-formulated tile bodies. During the studies, SEM in combination with EDS, and thermal analysis techniques such as non-contact dilatometry were widely employed. The results indicated that it was possible to use the waste materials in the commercial tile production without deteriorating the relevant technological properties.

Jan 1, 2006

By Jean Igor Margem, Lucas Barbosa de Souza Martins, Frederico Muylaert Margem, Noan Tonini SImonassi, Sérgio Neves Monteiro, Rômulo Leite Loiola

"Fibers of giant bamboo (Dendrocalmus Giganteus) are amongst the strongest lignocellulosic fibers. Although studies have been already performed, limited information exists on the mechanical properties of polymeric composites reinforced with continuous and aligned giant bamboo fibers. This work evaluates the tensile strength of this type of composite. Standard tensile specimens were fabricated with up to 30% of fibers aligned along the specimen's length. The fibers were press molded with a commercial epoxy resin mixed with a hardener and cured for 24 hours at room temperature. The specimens were tested in an Instron machine and the fracture surface analyzed by scanning electron microscopy. The tensile strength increased significantly with the amount of giant bamboo fiber reinforcing the composite. This performance can be associated with the difficult of rupture imposed by the fibers as well as with the type of cracks resulting from the bamboo fiber/epoxy matrix interaction, which prevents rupture to occur.IntroductionDue to growing concern about the ambient impacts from industrial activities, our society is ever more using environmentally friendly materials. In this regard, cellulose-based natural fibers, known as lignocellulosic fibers, become a promising solution. Nowadays, they are being considered as a substitute for synthetic fibers, such as glass fiber, used by the industry on a large scale [1-5]. The application of these natural fibers is also motivated by many advantages like good toughness and less wear of equipment used in the processing of composites. In addition, such composites are environmentally friendly because they are renewable, biodegradable and neutral with respect to C02 emissions, the main responsible for global warming and climate changes. [3,5,6].Lignocellulosic fibers also have some disadvantages in relation to synthetic fibers such as the difficulty of coupling with polymer matrices, due to the hydrophilic character of fiber and the hydrophobic nature of the matrix, as well as dimensional heterogeneity [ 4,5]. This last one is characteristic of the nature of this material and constitutes an obstacle to the use of these fibers in certain projects, especially those that aim high performance. The above mentioned disadvantages are worrisome reasons for the occurrence of reduction in the strengthening capacity, as indicated by the rule of mixtures for composites [7]."

Jan 1, 2013

By K. S. Jeong

Since the start-up of the Onsan Smelter in 1979, LS-Nikko Copper has grown into a competitive smelter through continuous development. Several environmental improvements have been carried out, in particular, intensive investments in reducing SOx emissions, such as de-sulfurization plants, fugitive gas capturing and TMS(Tele Metering System). In addition, in recent years LS-Nikko Copper has spent more than 10 million USD every year to improve environmental conditions. In order to be a global leading smelter in every aspect especially environmentally, LS-Nikko Copper plans to inspire environment-friendly minds, co-operate with shareholders, and participate in global conventions. This paper describes the environment improvements carried out at Onsan and briefly introduces a sustainable vision for a green smelter.

Jan 1, 2006