Search Documents

By V. D. Tathavadkar

Chromite ore is of immense importance for the extraction of metallic chromium and chromium chemicals. The mineralogy and crystal structure of chromite phase are therefore important part of our investigation on the extraction chemistry of chromium species. In this investigation, we have studied the effect of the processing parameters, i.e., the temperature and the oxygen potential on the microstructure and composition of mineral phases formed in the Cr2O3 ?Al2O3 -FexOy -MgO system. In particular the importance of the spinodal decomposition reaction is emphasized in the extraction of chromium as sodium chromite and sodium chromate. Experiments were carried out in order to study the differences in the crystallography of different chromite minerals. Phase equilibria in natural chromite minerals were investigated by calcining chromite mineral in air, argon, and 5% hydrogen + argon atmospheres over a temperature range from 200 to 1200 °C. The effect of the oxygen partial pressure and temperature on the phase constituents of the calcined product has been discussed. The microstructural changes were examined using scanning electron microscope (SEM) and the changes in elemental composition in different phases were analysed by electron probe micro analyser (EPMA). The results obtained from EPMA studies were used to calculate lattice parameter of the spinel lattice, and these values were compared with the values obtained from X-Ray powder diffraction data. On the basis of the experimental data, the mechanism of the spinodal decomposition of complex spinel phases is described under the influence of oxygen partial pressure and temperature.

Jan 1, 2000

By C. Pereira

Spent nuclear fuel (SNF) can be treated in a molten salt electro refiner for conversion into metal and mineral waste fonns for geologic disposal. The fuel is dissolved in molten chloride salt. Non-transuranic fission products in the molten salt are ion-exchanged into zeolite A, which is subsequently mixed with glass and consolidated. Zeolite was found to be effective in removing fission product cations from the molten salt. Breakthrough of cesium and the alkaline earths occurred more rapidly than was observed for the rare earths. The effluent composition as a function of time is presented, as well as results for the distribution of fission products along the length of the column. Effects of temperature and salt flow rate are also discussed.

Jan 1, 1996

By ZhiLong ZHAO, Lin Lin, Zhancheng Guo, Jingtao GAO, Huiqing Tang

Grain sticking often occurs in the fluidized bed reduction of f ine iron ore, which is closely related to the precipitation morphology of metallic iron on the surface of ore particles. In this work, simulating the gas-solid reduction process of iron ore, in situ observations were carried out to investigate effects of doping mineral oxides on the precipitation morphology evolution of metallic iron during reduction of iron oxides with CO. Results indicate that the precipitation morphology of metallic iron is related to the quantity of doped mineral oxides. The minimum mole fraction of doped oxide ( xyOA N ) that can inhibit the growth of iron whiskers is related to its cation radius ( Ax r ), extranuclear electronic layers ( Ax n ) and valence electrons ( Ax q ). Their relation can be expressed as:

Jan 1, 2016

Physical and chemical properties of the salt flux phase play a significant role in the recycling of UBC in Aluminum melting processes. Particularly knowledge of several properties such as salt vapor pressure, melting temperature, loss of aluminum, corrosion of refractories are useful for the process control decisions in order to attain a good quality of aluminum produced. A literature review and analysis of several salt flux systems for the selection of a flux for the Aluminum melter (low temperature natural gas bath melting) process were made. Based on these analysis two salt flux systems are recommended for further studies. These are NaCl?KCl?LiF system and NaF?LiF?KCl system with small amounts of other salt additives. Application of these fluxes to Al industrial processes are discussed.

Jan 1, 1996

By Yunnen Chen

The test and use of natural materials as biosorbents for the removal of heavy metals from industrial wastewater is under constant development. In the present study, the biosorption capacity of waste microzyme was studied for cadmium The cadmium removal study has been carried out batchwise where the influence of physico-chemical key parameters such as pH value of solution, contacting time and initial cadmium ions concentration have been considered. The influence of metal ion concentration was evaluated and the results were fitted using adsorption isotherm models. The kinetic of cadmium biosorption was also investigated. The maximum percent removal was attained at the pH 7.0 after about 30 min. Waste microzyme was a potential biosorbent for the removal of Cd(II) from the effluent of electroplating industry.

Jan 1, 2009

By Fernanda Margarido

Recovery of metals contained in the electrode materials of batteries was studied considering an integrated recycling process constituted by physical and chemical operations. The physical treatment included the shredding of the spent batteries, followed by a wet sieving operation of the fragmented material. The physical behavior of Ni-Cd and Zn-Mn based (alkaline and saline) system batteries was studied and compared. In that sense, shredding operation was performed and the sieving of shredded fractions was accomplished to evaluate the efficiency of the separation of electrodes and scrap. For Ni-Cd batteries the loss of electrode material with the supra fraction (scrap) after the shredding operation was lesser than the Zn-Mn batteries. Especially for saline-type batteries, the electrode attached to the scrap was substantial leading to important losses. This difference can be explained by the composition of the case materials and the internal physical constitution of the electrodes. The wet sieving studies carried out allowed optimizing the separation of the electrode fine fractions from the scrap materials through the analysis of selectivity Cd/Fe or Zn/Fe. For Ni-Cd batteries, maximum selectivity was achieved for the granulometry of 1.4 mm, while for alkaline and saline systems best selectivity were obtained at 2.8 mm and 5.6 mm, respectively. This process allowed the recovery of about 70% of electrodes for Ni-Cd and alkaline systems, and 50% for saline batteries, with less than 5% of scrap as contaminant. This physical step can be considered as a pre-treatment of this type of waste material envisaging its valorization by chemical treatment, as improves the concentration of the elements of interest and decreases the iron content.

Jan 1, 2006

Two pilot-plant investigations were conducted in which strong-base resins were compared with activated carbon for the extraction of gold cyanide from leached pulp from the Golden Jubilee Mine. The results show that gold can be recovered with carbon, but that the extraction efficiency is poor, probably because high concentrations of humic and fulvic acids are. present m the pulp. .However the extraction of gold cyamde from this material with strong-base resins JS very effo:1ent, and the overall efficiency of extraction is better with resin than with carbon, even when the concentration of resin is one-third that of carbon, and the flowrate of resin is one-third that of carbon. The results of the pilot-plant campaign reported in this paper led to the conversion of the Golden Jubilee plant from carbon-in-pulp to resin-in-pulp in February 1988.

Jan 1, 1989

By Kelly J. Driscoll

Impure zinc (98.5%) was electrorefined to high purity zinc (99.995%) using a fused salt electrolyte of molar composition 1: 1 : 1 :2 ZnCI2:KCl:NaCl:LiCl with a current efficiency of about 90% at 723 K. A recessed channel electrorefining cell was developed which achieved excellent mixing of both the metal and the electrolyte and by ensuring a very small anode to cathode spacing the voltage drop across the cell was 0.16 V and at a current density of 7kA m-2. The physical characteristics of the cell were observed using a low temperature model which showed the formation of droplets and rivulets which provided mixing. The application of this approach to the refining of other non-ferrous metals is discussed.

Jan 1, 1992

By Jagdish C. Agarwal

Although copper ranks very low in the order of abundance of elements in the crust of the earth, it has been one of the first metals utilized by mar, at his emergence from the Stone Age, about 10,000 years ago. Use of copper for weapons, tools, utensils and ornaments dates back to the twilight of history, 6,000-5,000 B.C. Native copper outcrops and the malleability of the metal explain its very early use by the cave-dwellers. The working, melting and extraction of copper from its minerals are among the oldest metallurgical achievements of the human race. The oldest complete smelting installations for the extraction of copper from its minerals, dated about the fourth millenium B.C., were recently discovered in the Timna Valley, Wadi Arabah, Israel. (1) The history of the developments of the extractive metallurgy of copper has been adequately reviewed recently. (2,3) The center of copper production migrated from the Eastern Mediterranean to Northern Europe (Mansfeld, Germany, Swansea, Wales) towards the end of the Middle Ages (1500 A.D.). The production of the metal was boosted tremendously in North America since the end of the nineteenth century (Fig. 1).

Jan 1, 1976

By KAGAN BENZESIK, Onuralp Yücel, Mehmet Bugdaycı, Ahmet Turan

ZrB2 and B4C are one of the most significant advanced ceramics. They are being used in various industrial areas from space technology to nuclear industry owing to their physical properties such as high melting point, high thermal/electrical conductivity and low density. Present study was conducted in two main stages: Self-propagating high-temperature synthesis (SHS) reactions and leaching. ZrO2, Carbon black, B2O3 were used as starting material to produce ZrB2-B4C powders by SHS. Also Mg powder was used as the reductant. The reaction mixtures (approximately 100 g) were mixed thoroughly 15 minutes in a turbula mixer and charged into Cu crucible and compacted. W (tungsten) wire was placed at the top of copper crucible and the reaction realized by passing current through the wire. After initiation, a highly exothermic reaction became in a self-sustaining mode and propagated throughout the SHS mixture. The samples were characterized by using AAS and X-Ray Diffraction.

Jan 1, 2016

By Denise Nascimento, Alice Barreto Bevitori, Felipe Perissé Duarte Lopes, Renan Carreiro, Sergio Neves Monteiro, Isabela Leão Amaral da Silva

"Natural fibers obtained from plants have increasingly been used as reinforcement of polymeric composites in engineering applications. This is the case of the fiber extracted from the piassava palm tree, a native of the southeast region of South America, which for a long time has been used in simple items like brooms and brushes. Recently it was reported that the tensile strength of the piassava fiber varied inversely with the equivalent diameter. Following that previous work, the elastic modulus and the density dependence on the diameter of stiffer piassava fibers of the Attalea fiinifera species was investigated. Precise measurements with a profile projector and Weibull analysis of the experimental results indicated that both the elastic modulus and the density of piassava fibers also follow an inverse correlation with the diameter. Scanning electron microscopy observations of the microstructure and fracture surface showed that defects and participation of microfibrils are responsible for this correlation.IntroductionIn the past decades, both the increase in the price of the petroleum and climate changes due to greenhouse gas emissions are motivating the use of renewable and low cost natural materials as a substitute for energy intensive and CO2 contributor synthetic materials [1]. A typical case is that of natural cellulose-based fibers extracted from cultivated plants in comparison to glass fibers, which are extensively used for composite reinforcement. In fact, these natural lignocellulosic fibers are increasingly being investigated [2-6] as possible reinforcements of polymeric composites, and in some cases, successfully replacing glass fiber composites in engineering applications [7]. The automobile industry has remarkable examples of lignocellulosic fiber composite substitutions [8-10]. Not only do some of these fibers display specific mechanical properties comparable to glass fibers but their composites also contribute to lower equipment wear and better finishing of molded components [6]."

Jan 1, 2012

By Zhigang Liang

A carbon free precast block was prepared by using high-alumina fused corundum as aggregate and fused magnesia, and ultra-fine Al2O3 and ultra-fine SiO2 powders as matrix materials. A small linear expansion for the precast block was achieved through spinel formation from the reaction of MgO with Al2O3. The precast block showed a lower apparent porosity, higher hot modulus of rupture and better slag corrosion resistance compared to the traditional Al2O3-MgO-C brick. Moreover, the practical application of the precast block to the ladle lining proved it to possess a better thermal insulation which could effectively prevent the temperature drop of molten steel during the refining process. It can be predicted that the carbon free precast block could possibly be accepted as a new type of ladle lining material for the production of low-carbon and ultra-low-carbon steel.

Jan 1, 2009

By Pesic. Batric

A novel chitosan-pyridoxal-epichlorohydrin was synthesized and evaluated in our laboratories. The evaluation was achieved by performing kinetic and equilibrium studies of copper sorption. The parameters examined were pH, temperature, concentration of copper, particle size and selectivity of copper sorption against iron, zinc, cadmium and cobalt. It was found that pH was the most important parameter, and sorption of copper increased with pH increase in the range pH 2.5-6.0. The low activation energy of the sorption reaction, 1 1.13 kJ/mole (2.66 Kcal/mole), showed that temperature was not an important parameter. The synthesized chitosan was selective against iron, zinc, cadmium and cobalt. The selectivity with respect to last three metals was achieved by the kinetic difference of sorption, as sorption of copper was much faster than for other metals. Iron (Fe2+) does not adsorb on chitosan. The mechanism governing the sorption of copper is intraparticle diffusion. This finding was supported by the dependance of copper sorption on the square root of time, the low activation energy, and the fit of experimental data in the diffusion through the product layer equation.

Jan 1, 1994

By Ajay K. Singh

The surface quality demands for galvanized and galvannealed steel sheets by the automotive and appliance industries have been getting increasingly stringent over the past few years. Intensive efforts by Hot-Dip-Galvanizers to meet these demands have resulted in substantial improvement to the hot dip coating process. However, elimination of zinc bath contaminants which directly affect the coated strip surface quality continues to remain a tough challenge. As part of our effort to improve the zinc bath cleanliness, Inland Steel Company has developed a test method to quantitatively measure the contaminants in incoming zinc spelters and establish a specification for incoming zinc quality. The test is currently being used for auditing the incoming zinc quality. The zinc suppliers are also using this test for quality control purposes. The purpose of this paper is to describe the test method and how it has improved the galvanizing operation at Inland.

Jan 1, 1992

By N. L. Piret

In copper smelting minimization of solid waste generation is receiving increased attention with more stringent environmental legislation and lower disposal space availability. Copper smelting slags generally being valorizable, solid waste generation is attributed to the presence in the feed of unvalorizable impurities which do not report to the slag and to the unavoidable formation of contaminated dilute acid solutions which need neutralization. As to unvalorizable impurities, solid waste minimization is achieved by rejecting them in the highest possible concentration. Dilute acid is mainly due to the formation of SO3 in the smelter gases and to the discard of decopperized bleed-off electrolyte. Its generation is substantially lowered by preventing SO3 formation, by converting the dilute acid to a valorizable product, e.g., by thermal decomposition for H2S04 recovery or by precipitation as chemical gypsum, and by suitable treatment of the bleed-off electrolyte for impurity removal. Industrial processes are evaluated and alternatives are discussed.

Jan 1, 1994

By C. P. Manning

This paper reports recent progress in the development of a unique metal extraction technology utilizing zirconia-based inert anodes for the electrolytic reduction of metals from their oxides. In this process, the target metal oxide is dissolved in an ionically conducting liquid solvent phase. An extended anode consisting of an oxygen-ion-conducting stabilized zirconia membrane in intimate contact with a catalytically active electronic phase and an inert electronically conducting cathode are inserted into the molten flux containing the oxide. When the appropriate electric potential is applied between the electrodes the target metal is reduced at the cathode and oxygen ions are selectively transported across the stabilized zirconia membrane and oxidized at the anode. When the process is conducted at temperatures between 1200-1400°C, the ohmic resistance drop across the stabilized zirconia membrane is low, and high current densities on the order of I A/cm2 or greater can be obtained. In addition, the process efficiency can be increased further by directly reforming hydrocarbon fuel over the anode. Laboratory experiments at Boston University have demonstrated the technical viability of employing zirconia-based inert anodes for environmentally sound production of metals such as magnesium, tantalum, aluminum, etc., directly from their oxides. Significant progress has been made in the application of this concept to the electrolytic reduction of magnesium at 1300°C. The research topics covered include stability of the zirconia membrane in the selected molten solvent (flux), volatility of the flux, electrochemical characterization of the electrolytic cell, and analysis of the metals produced.

Jan 1, 2003

By R. E. Moore

The lining systems currently in use in BOF furnaces, certain steel ladles, and the slag line of electric are furnaces were developed during the late seventies through the mid-eighties using a trial and error method of combining aggregate, carbon sources, additives and binders. They are currently based on magnesia, graphite, metal additives and resin binders, the selections of each being tied to the anticipated intensity of the use conditions. The general functions of the respective constituents are well appreciated, however, there is still a great deal that is not known about how the socalled antioxidants protect the graphite nor how impurities from the graphite and the aggregate enter into the wear processes. In a simplified assessment of wear processes, it appears that if the deoxidized layer can be kept very thin, less than 810 mm in depth, and if the viscosity and quantity of the matrix glassy phases can be controlled to resist erosion of the deoxidized layer, lining life can be maximized for the various applications. This paper will discuss the characteristics of the starting materials systems currently being employed for applications requiring a deoxidation function to realize extended wear. It will not attempt to explain all the complex interrelationships between the respective constituents but will point to the potential for improvements through the use of improved constituents.

Jan 1, 1991

By L. A. Harris

The formation of coke during coal liquefaction can eventually result in catastrophic failure of the conversion system. Coking typically proceeds by the formation of liquid crystals (mesophase) and the subsequent separation of these crystals from the plastic phase formed during heating of coal. The anisotropy of the mesophase makes it readily detectable in the optical microscope under polarized light. This study examines the solids formed during coal liquefaction processing by optical and electron microscopy. Observations on the relationships between the coke morphology, minerals and inert macerals are presented.

Jan 1, 1982

By Yongbin Yang, Meixia Cai, Yufeng Guo, Guanzhou Qiu, Tao Jiang, Jianjun Fan

"A series of sintering and metallurgical experiments were carried out to optimize the blast furnace burden structure in this study. The results indicated that the sinter disintegrated seriously with basicity around 1.4, and after this “turning point”, the sintering properties were improved gradually with the increase of basicity of sinter. Based on the results, an idea was put forward which focused on producing two different kinds of sinter with different basicity. Different with the original burden structure of 85% sinter with basicity 1.4-1.5 + 15% pellets, an alternative new BF burden structure was proposed by the following structure?44% sinter with basicity 1.05 + 44% sinter with basicity 1.87 + 12% pellets. This new alternative BF burden structure has been adopted by some steel plants.IntroductionIn recent years, conventional blast furnace (BF) process was put into operation to produce hot metal in “A” steel plant. “A” steel plant owns two sets of sinter strands at present. Because the sinter production capacity exceeds the actual requirements of BF, a burden structure with 85-90% self-made sinter + 10-15% purchased pellets is adopted to take advantage of the low–cost sinter. But the serious problems encountered with the BF operators are that the sinter disintegrated easily during transportation and storage process. Therefore, the rate of return fines is very high after sinter being screened."

Jan 1, 2012

By A. A. Bustos

A model was developed to simulate the blow-by-blow operation of the converting process. From the weights, compositions and temperatures of all converter feeds the model calculates the composition and tonnage of both converter matte and slag as well as bath temperature at the end of each blow. The development of the model and its application to the converter aisle operation are described. There is good agreement between model predictions and observed results. At the present time the model is being used to investigate different converting schemes and their effect on pay metal recoveries, slag chemistry and temperature of the bath. Future work involves the use of the simulation model as a process control tool for the converting operation.

Jan 1, 1988