Search Documents

By J. Bertisen, G. Davis

Previous analyses of small samples of mining projects have found that feasibility studies tend to well under-estimate the actual capital costs of the project. Our review of 63 mining and smelting projects completed over 4 decades confirms that as-built capital costs are, on average, 25% higher than as estimated at the bankable feasibility study stage. There appears to be little attenuation over time of this bias in capital cost estimation, at first appearing to reflect an absence of learning on the part of the consulting engineer. We instead argue that this persistence of bias is intentional, driven by a scarcity of project financing and the need to inflate the project economics in a bid to secure financing. Around this intentional bias is a considerable amount of scatter. Roughly half of all projects’ as-built capita costs fall outside of the expected ±15% of the feasibility study capital cost estimate, even after allowing for intentional estimation bias. Cost overruns of 100% or more happen in roughly 1 out of 13 projects. The data reveal that a shifted lognormal probability distribution should be used when modeling mining project capital costs in a Monte Carlo analysis.

Jan 1, 2007

By Ryan P. Sullivan, G. Alan Klevens, Jian Huang

"BACKGROUNDLake Hamilton in Hot Springs, AR was created in 1932 when the Arkansas Power and Light Co. completed Carpenter Dam on the Ouachita River to generate electricity. Today, the 7,200-acre (2,914 hectares) impoundment is one of Arkansas’s most popular recreational and residential lakes.U.S. 70 crosses Lake Hamilton by means of a seven-span bridge featuring nine steel girders per span. Constructed between 1982 and 1984, the 1,410-foot long (430m) bridge carries four lanes of traffi c across the lake. The bridge is supported by six intermediate reinforced concrete piers composed of hammer heads, stems, footings and seals, which sit on the underlying rock. (See Figure 1). The bridge rises to a maximum of 33 feet (10m) above the surface of the lake and the footings and seals extend a maximum of 29.5 feet (9m) below the surface of the lake. The seals are situated on hard, fractured sandstone and shale.Routine underwater inspections in 1993 revealed large cracks in the lean seal concrete and refl ective cracks in the reinforced concrete footings. Infrastructure Engineers, Inc., The Arkansas State Highway and Transportation Department’s (AHTD) design consultant, then conducted an in-depth underwater inspection of the pier foundations. The investigation included cross-hole sonic logging, singlehole sonic logging, visual examination and strength testing of core samples, and petrographic analysis.The investigation revealed extensive cracking and low-strength concrete within the seals of all intermediate pier foundations. Many voids within the seal concrete had become fi lled with silt. There was evidence of continued seal deterioration between underwater inspections.AHTD and its engineers considered three rehabilitation solutions in the preliminary engineering stage: micropiles, a cofferdam supported concrete jacket, or a pile supported concrete jacket. The three alternatives were estimated to cost $1,250,000; $4,320,000; and $3,030,000 respectively. All three options would transfer the loads from the pier footing directly to the rock below, bypassing the seal concrete."

Jan 1, 2007

By Y. A. Topkaya

In this research work, a process was described for the recovery of copper and zinc in copper converter flue dust from the Black Sea Copper Works' Samsun Smelter Plant. After characterization of a representative flue dust sample, the process included roasting of the flue dust and then leaching in dilute sulfuric acid solution. Roasting time and temperature were studied to determine the optimum roasting conditions. Sulphuric acid concentration, duration, temperature of leaching and solid to liquid ratio were the parameters studied in the bench scale laboratory leaching experiments.

Jan 1, 2007

By J. West

For many years line-of-sight (LOS) issues for underground mobile equipment is a growing focus of research. This research is a result of the numerous fatalities and injuries which occur in the mining industry and which are related to poor operator LOS. Three assessment methods are currently used to assess operator LOS of underground mobile equipment. The light filament (LF) method is a hands-on assessment method that is performed in the field. This method is not evaluated in this paper. The laser scan (LS) method of assessing equipment is a quick and reliable method that comes from the need to evaluate vehicles already located in the field. The computer simulation (CS) method can assess LOS issues using a computer aided drawing (CAD) model, which is useful for assessing current or prototype models. The purpose of the current research is to compare and validate different operator LOS assessment methods. Comparison of the results of the LS and CS visibility plots yielded similar quantifiable results. A visual comparison of the results further illustrate that the LS and CS methods are acceptable assessment tools for mobile equipment operator LOS evaluation. The visibility assessment methods are now being prepared as guidelines for the mining industry to assess current and potential designs.

Jan 1, 2007

By John E. Newby

Washington?s King County is constructing a new regional wastewater treatment facility, called Brightwater, in response to growth in the greater Seattle region. Planning conducted in the late 1950s identified the need for two regional treatment facilities. Constructed in the 1960s, these plants have served the region well. However, an eventual need for a third facility was also recognized. The Brightwater project implements the final phases of the long-term plan. The project includes a new treatment plant and an extensive conveyance system. When completed in 2010, the Brightwater facilities will treat sanitary sewer flows from growing populations living in northern King County and southern Snohomish County. The new system will fulfill commitments to provide wastewater services to local jurisdictions and sewer service providers in the King County Service Area. It will also provide more flexibility in the operation of the King County regional wastewater system. The Brightwater wastewater treatment plant will provide secondary treatment capacity using membrane bioractor technology in 2010 for 36 million gallons per day (mgd), with anticipated expansion in 2040 to 54 mgd, using membrane bioreactor technology. These capacities are for average wet-weather flows. The plant will also accommodate peak hourly flows of 130 mgd by 2010 and 170 mgd by 2040. The Brightwater Conveyance System consists of more than 8.1 km (13 miles) of tunneled influent and effluent conveyance lines, five tunnel portals/shafts, microtunneled influent and outfall connec-

Jan 1, 2007

Western Fuels Association, Inc. ?WFA was formed in 1976 ?Nation?s first fuel supply cooperative ?Original members included Basin Electric and Tri-State G & T ?Formed to ensure provision of coal supply to new power plant projects being constructed

Jan 1, 2007

By R. Van Rijswick

Crankshaft driven piston and piston diaphragm pumps inherently generate a varying flow each crankshaft revolution. Depending on the system connected, this flow variation results in a pressure pulsation. This pressure pulsation may, depending on the structural design, result in structural vibrations. In order to limit the level of pressure pulsations, volume absorbing devices, mostly gas filled vessels, are used. The standard selection of these so-called dampeners is based on the flow variation of the pump but does not incorporate the interaction with the connected system. The paper discusses the application of a pulsation analysis tool developed by WEIR Minerals Netherlands, manufacturer of GEHO positive displacement slurry pumps. The paper first discusses the basics of pressure pulsation analysis, such as flow variation generated by crankshaft driven pumps, and hydraulic effects such as capacitance, inductance and resistance and their influence on the hydraulic response of a system. Furthermore, the relation between pressure pulsations and structural vibrations, known as fluid structure interaction, will be discussed. Additionally, the capabilities of the pump pulsation analysis tool are presented, illustrated by examples of simulation results and experimental verification.

Jan 1, 2007

By Rajib K. Mohapatra, K. Vizaya Kumar

In any manufacturing organization internal logistics plays a vital role in improving and maintaining the productivity. In Ferro Alloys manufacturing organization where there is huge input of raw material in terms of ore, reductants and variety of fluxes amounting to about four times of the mass of alloy produced need to be handled from yard to furnaces , internal logistics requires utmost attention. Any deviation or mismatch between stock and requirement will affect furnace operation. Though the activities are being outsourced by most of the organization, these require close monitoring. This communication presents an optimization model which can work as a ready reference for the manager to decide upon the material quantity and the furnace to be fed with an objective of minimizing the cost of handling and zero production loss.

Jan 1, 2007

By Jim Richards, Eli Choueiry, Brett Robinson, Amanda Elioff

The Los Angeles Metro Gold Line Eastside Extension (MGLEE) extends Metro’s light rail system to the densely populated and growing East Los Angeles communities. Much of the 6 mile alignment consists of at-grade track, but the project also features a1.7 mile underground segment in cut-and-cover and twin-bored tunnel structures. In light of past experiences with open shield construction, The Metropolitan Transportation Authority (Metro) specified, for the first time, use of Pressure Face Tunnel Boring Machines (TBM’s) to advance tunnels through soft ground. This paper describes the history of the tunnel design, construction management, and construction methods adopted that resulted in successfully completing the tunneling segment.

Jan 1, 2007

By S. Jordanov

The nature of processes that take place on top of copper bearing grains during the suppression of copper acid drainage from mine tailings was studied on a grain model. Cyclic voltammetry (C.V.) was employed as an experimental technique suitable for indirect measuring of copper leaching. Experiments were done in sulfuric acid (pH=2) at electrodes that progressively approach the real situation during acid main drainage, starting with Cu-metal, then with CuO and finally with CuO covered with CaSO4. Oxidation was found to be the only process that takes place on metallic copper electrode anodically polarized up to 2 V vs. Cu/CuSO4 reference electrode. Dissolution is intensive and reaches up to 50 mA.cm-2. When the same was repeated, but on CuO electrode, anodic currents were some 4 times lower than on the bare metallic surface. This indicates that the electrode material is not completely oxidized to copper(II)oxide and the Cu(O) or Cu(I) residues are oxidized during the anodic polarization. This explains the diminished dissolution. Dissolution is further restricted at electrodes covered with CaSO4. It is some 20 times lower than on the bare oxide electrode. When the second layer of CaSO4 was applied, anodic currents were another 15 times lower. Total decrease of anodic currents when transition is made from Cu-metal to CuO covered with 2 layers of CaSO4 reaches up to 7.500 times. C.V. measurements produced a proof that mechanical blockage is the way how lime prevents leaching of copper bearing grains in immobilization experiments referred elsewhere.

Jan 1, 2007

By A. Eslami

When producing high grade mattes in smelter plants, copper losses in the slag are inevitable. Hence, the recovery of copper from slag has been the focus of many research projects, copper flotation being a widely used process. In the Khatoonabad converter, 200 t/d of slag are presently produced with a grade of 2.3% Cu. Assuming a 85% recovery by flotation, about 3.9 t/d copper could be produced, which is of prime importance economically. In the present work, a sample of this slag was crushed and ground in the laboratory to liberate the copper-bearing minerals. Following mineralogical studies, optimum laboratory flotation parameters were obtained, resulting in 90.27 % recovery and 9.42% of copper grade for the rougher stage. At pilot scale, a pulp of 28% solids was floated at ph 10.5 using 40 git of Z6, 25 git of R407 and 20 git of MIBC and A65. A recovery of 83.52% was obtained for a concentrate grade of 28.36% Cu. In the rougher cells, the feed consisted of particles 94% finer than 74 microns whereas in the cleaning stage, particles were 95% finer than 44 microns. Based on the obtained results, the Sarcheshmeh Khatoonabad converter slag is presently being fed to the Chargonbad flotation plant, where a concentrate of 32% copper at 86% recovery is being produced.

Jan 1, 2007

By D Chalmers

Drill and blast mining techniques are used to mine coal outburst prone and high gas content coals in Australia. As the risk of an outburst is increased in high gas content coal, it is considered that drill and blast is the safest way to mine coals that refuse to yield gas even after considerable gas drainage efforts. The availability of suitable explosives for drill and blast in Australia is dependent on the æBuxtonÆ tests. With the diminished coal operations in England, the type and supply of such explosives is tenuous, causing significant disruption to the production of coal in some mines. In an attempt to free up the availability of explosives a review of the methods used for the testing of coal mine explosives was undertaken to ascertain the scientific basis for these tests. It was hoped that this comparison would allow regulators to have the confidence in explosives that had been tested elsewhere. Although this was not achieved, it has spawned a major research project that aims to better understand the mechanisms involved so that either confirmation of the current testing regime can be achieved or more suitable and scientifically based tests can be adopted. This paper looks at the ongoing research program investigating the parameters that are involved with methane ignitions from explosives. By utilising high-speed data capture and processing the research project is trying to view an ignition as it happens to identify the mechanisms involved so that better explosives can be designed for the coal mining industry.

Jan 1, 2007

By C O. Gomez

The bubble size, together with the gas rate, determines the bubble surface area flux in flotation machines and, therefore, impacts directly on the kinetics of flotation. Understanding the variables that influence bubble size is one of the keys to understanding flotation recovery. Surprisingly, these relationships are poorly understood, largely due to the difficulties associated with gas dispersion measurements in industrial environments. The McGill gas dispersion sensors (bubble size, gas rate, gas holdup) are capable of reliably making such measurements. This paper reports on a study, using the McGill sensors in a 0.8 m3 Metso RCSTM pilot cell, which investigated the effect on bubble size of frother type and concentration, gas rate, temperature and rotor speed. A Denver laboratory cell was used to investigate the effect of elevation above sea level. Frother concentration proved to have the predominant influence on bubble size, and the effect of frother type can be normalised as a function of the critical coalescence concentration (CCC). Measurements made at many plant sites worldwide are compared to the model developed using the Metso RCSTM unit.

Jan 1, 2007

By Christian Roche

Our study is focused on the sub-assembly con-tact shoes, pressure rings and pressure bellows. We were keen to mainly study [ ] 1.The contact shoe design 2.The most efficient pressure to ensure an optimal electrical contact between the contact pad itself and the casing 3. The contact shoe cooling circuit in view to provide to the shoe the best mechanical and electrical characteristics in order to bring to the users of COFOR® components a new standard in process setting technical solutions. A finite elements simulation, combined with a thermal and structural studies were used. Our presentation which follows is dedicated exclusively on the influence of the contact shoe cooling system on the process through a thermal and structural analysis. [ ]

Jan 1, 2007

By Descour Jozef, Suguru Shirasagi, Takuji Yamamoto, Koji Murakami

For TBM tunneling no visual inspection of excavated ground is possible. This may hinder the high-speed excavation, particularly in complex ground conditions. The TBM Excavation Control System was developed for better prediction of geological conditions ahead of the tunnel face during excavation. The seismic reflector tracing produces volumetric images of anomalies in the ground in “near-real time.” These images are verified using logging data from pilot boring and TBM driving data, to improve reliability and precision of ground mapping. Also good correlation was obtained between the rock strength index computed from TBM data, and one derived from volumetric seismic images.

Jan 1, 2007

The simple act of taking a sample implies that someone will use the information contained in the analytical result to make a decision about a course of action. In the mining industry, the decisions may involve huge capital commitments for opening or closing a mine, or marginal tactical costs that involve deciding if a truckload of mineralized rock should be sent to the mill for processing, or the waste dump. Sampling is among the most fundamental activities in a mining operation, and this paper aims to examine some of the technical issues that can assist in ensuring that samples are representative and correct. Insights into the scale of variability require that we disaggregate sampling variance into its component parts and evaluate each one individually. The work of Pierre Gy in understanding the different sampling errors is the first step in establishing an optimal protocol. This must be followed by the appropriate measures to ensure the protocol is implemented such that minimal bias is introduced in the sampling process. Even with these insights the possibility exists for large unseen and hidden costs can accumulate in a mineral development because of sampling errors. These hidden costs arise due to misunderstanding of the principle factors that affect the size of sampling errors, such as the mass of the sample, the effects of splitting a sample to reduce the mass, and the influence of the nominal particle size. The handling of sample material without due regard to the sampling characteristics of the material being sampled is also a major source of sampling errors. The most significant problem is due to the influence of the so-called volume-variance effect. This effect is a consequence of the support effect and the information effect both of which relate to the difference in size at which samples are collected and mining blocks are extracted. The information effect is a function of the availability of data at the time that decisions are made about the destinations of mineralized rock, namely the mill or the waste dump. Implementation of appropriate sampling protocols in the mineral value chain remains a challenge throughout the industry. The growing understanding and deepening appreciation of sampling theory and methods means we stand on the threshold of a new era for implementing and understanding appropriate sampling procedures and protocols. In the interests of optimal development of the national patrimony it is suggested that standardization through the identification of structural problems and continuous improvement of mining processes be instituted at a national level.

Jan 1, 2007

By L Lorenzen, C Aldrich

In this paper, a neurofuzzy model is proposed for the development of an explanatory model of an industrial gold leach circuit based on historic plant data. A regression tree was used to partition the data in the predictor variable space and the structure of the tree was used as a basis for the derivation of fuzzy rules that could be integrated into a fuzzy expert system useful for operator decision support or process control. The position and shape of the membership functions were optimised with a backpropagation algorithm in a neural network framework. The approach yielded a significantly better explanatory model of the gold losses in the plant than comparable linear models. Although a regression tree could perform somewhat better in accounting for the variance of the dissolved gold losses, the tree was less robust than the fuzzy model.

Jan 1, 2007

By A. E. M. Warner, I. E. Hills, C. L. Harris

Since the late Dr. Keith Brimacombe, et al, performed tests at the now-closed Asarco Tacoma smelter and the Inco Copper Cliff Smelter on Peirce-Smith copper converters almost thirty years ago, many Pyro-metallurgists have investigated using the technology. To the best of the authors knowledge, except for shrouded tuyere technologies using substantial oxygen enrichments, the core idea of using high pressure air injection has not been implemented anywhere in the world. This paper reviews the fundamentals of this technology and summarizes the basic economic considerations. It also presents the circumstances of where and when high-pressure injection might be justified.

Jan 1, 2007

By Charles Stone, Hannes Lagger, Dru Desai

The design methodology of the planned Second Avenue Subway Project (SAS) led to development of the initial support design to estimate cost and quantities in the Preliminary Engineering (PE) stage. Careful selection of the cavern design rules that recognized the impact of rock quality, rock cover, excavation geometry, and excavation sequence helped to overcome the design challenges of large, shallow caverns for the initial ground support. In the course of the design verification process prescribed by the design methodology, the design team was continuously reviewing and updating the support quantities. The design procedure includes methods using different approaches of empirical, continuum, and discontinuum analyses, which are currently advanced in the Final Engineering (FE) stage. The paper is a continuation of the RETC 2005 “Trials and Tribulations” and focuses on the procedures that led to the changes in the initial support as a result of the ongoing design development.

Jan 1, 2007

By S. L. Zekovic

This paper analysis the medium and long-term perspectives, framework and considered possibilities of sustainable development of RTB "Bor" (Copper mines in East Serbia) after consolidation in the period of transition. The copper mine was opened in 1903. and today is the best quality copper producer on Balcan. This paper are elaborates the problems of privatization, debt, investment, growth of copper production from own mines (and imported raw), opening of new mines, economical efficiency of production, markets, environmental problems and impacts of the recent industry consolidation. The RTB "Bor" is a serious hot spot in Serbia. Unsustainable trends and processes are identified, as follows: open-pit waste dumps, flotation tailings, mining and processing waste waters, air pollution; no efficiency (excessive) using nonrenewal resource in the copper production; inefficiency in the use of energy, water and other inputs in copper complex; transboundary character of emissions of dust; environmental degradation and quality of wide area and ecologically highly risk, etc. Analysing some trends and planning-developmental perspectives and development strategies of company, it might be assumed that in the forth coming period, in parts of the Serbia, the borders areas of Bulgaria and Romania, there is an anticipated increase of ecological risk.

Jan 1, 2007