Search Documents

By K. Muehlenbachs, J. U. Stemler

"Abstract - The Boston deposit is a recently discovered Archean lode-gold deposit located approximately 700 km northeast of Yellowknife, in the southern portion of the Hope Bay volcanic belt. Primary H2O-CO2-NaCl fluid inclusions associated with gold mineralization at Boston are of low salinity (4.6 ± 1.4 eq. wt.% NaCl, n = 182) and contain pure CO2. Homogenization temperatures of liquid-phase inclusions average 270° ± 33°C (n = 141), but some fluid inclusion assemblages contain coexisting liquid- and vapor-phase inclusions that homogenize near critical conditions, suggesting phase separation. In these groups, liquid-phase inclusions homogenized at 299° ± 25°C (n = 24), and vapor-phase inclusions homogenized at 338° ± 28°C (n = 18). These temperatures overlap within error, and a median temperature of ~320°C is taken as representative of trapping conditions within the veins. An approximate pressure of 2-3 kbar was estimated from fluid inclusion isochores at this temperature. Stable isotopic compositions of carbonate minerals from the mineralized zones range from -4.7‰ to -3.1‰ in d13C, and from 11.2‰ to 12.8‰ in d18O; quartz ranges from d18O = 12.8‰ to 14.9‰; and pyrite ranges from d34S = 2.1‰ to 3.5‰. The d18OH2O, d13CCO2, and d34SH2S values of the fluid calculated from these minerals at 320°C are 6‰-9‰, -2.4‰ ± 0.6‰, and 1.5‰ ± 0.5‰, respectively, and are intermediate between metamorphic and magmatic compositions. A unique source for the fluids cannot, therefore, be constrained from these data. Petrographic and geochemical data for the Boston deposit are consistent with data from other Archean lode-gold deposits worldwide, implying that the Boston deposit formed in a similar environment and from similar types of fluids. These results suggest that the Hope Bay volcanic belt may represent a major new mesothermal gold belt in this part of Nunavut. Sommaire - Le gîte Boston a été récemment découvert à environ 700 km au nord-est de Yellowknife dans la partie sud de la ceinture volcanique de Hope Bay, il s’agit d’un gîte d’or filonien d’âge Archéen. Les inclusions fluides primaires de H2O-CO2-NaCl associées à la minéralisation aurifère du gîte Boston présentent une faible salinité (4.6 ± 1.4 eq. pds.% NaCl, n = 182) et contiennent du CO2 pur. La température d’homogénéisation des inclusions à phase liquide est en moyenne de 270° ± 33°C (n = 141), mais certains assemblages d’inclusions contiennent des phases liquides et gazeuses coexistantes qui s’homogénéisent dans des conditions quasi critiques, suggérant qu’elles résultent d’une séparation de phase. Dans ces groupes, les inclusions de phase liquide s’homogénéisent à 299° ± 25°C (n = 24) et les inclusions de phase gazeuse s’homogénéisent à 338° ± 28°C (n = 18). Ces températures se recoupent à l’intérieur des limites de l'erreur de mesure, et nous considérons qu’une température médiane de ~320°C est représentative des conditions de piégeage dans ces veines. Les isochores permettent d’estimer une pression d’environ 2-3 kbar à cette température. La composition des isotopes stables des carbonates dans les zones minéralisées s’étend de -4.7‰ to -3.1‰ pour d13C et pour de 11.2‰ à 12.8‰ pour d18O; les valeurs de d18O pour le quartz varient de 12.8‰ à 14.9; et les valeurs de d34S dans la pyrite vont de 2.1‰ à 3.5‰. Les valeurs de d18OH2O, d13CCO2, et d34SH2S du fluide calculé à partir de ces minéraux à une température de 320°C est de 6-9‰, -2.4‰ ± 0.6‰, et 1.5‰ ± 0.5‰ respectivement, reflétant des conditions intermédiaires entre des compositions métamorphiques et magmatiques. Il n’est donc pas possible d’identifier une source unique pour ces fluides à partir de ces données. Les données pétrographiques et géochimiques du gîte Boston sont similaires à celles d’autres gîtes d’or filoniens ailleurs dans le monde, ce qui implique que le gîte Boston s’est formé dans un environnement similaire à partir des mêmes types de fluides. Ces résultats suggèrent que la ceinture volcanique de Hope"

Jan 1, 2006

By O. Rabeau, M. Legault, F. Fallara

"Abstract - The development of robust 3-D geological models involves the integration of large amounts of public geological data, as well as additional accessible proprietary lithological, structural, geochemical, geophysical, and diamond drill hole data. 3-D models and maps have been available, particularly in the petroleum industry, for more than 10 years. Here, we demonstrate how robust 3-D maps can be used as interactive tools for mineral deposits exploration. In particular, we show how the interrogation of 3-D data sets can constrain exploration targets at depth. The main advantages of this technique for the mining industry are the homogeneity of data treatment and the validation of geological interpretations, taking into account geophysical and geochemical data. Data integration and cross-correlation of geology and geophysics can be achieved in two dimensions in any good GIS package. However, the added strength of 3-D analysis is the integration of separate data sets in three dimensions to build more complete, more realistic models, and in delineating areas of high economic potential at depth. Furthermore, these models can be modified and improved at any time by adding new data from ongoing drilling and geoscientific surveys. This paper presents two examples of 3-D models used for mineral exploration: the Joutel VMS mining camp and the Duparquet gold camp, Quebec. In both examples, the creation of the model is discussed and queries specific to the relevant exploration model are introduced. Eight potential exploration targets are generated at Joutel and seven at Duparquet. Although the targets defined are dependent on the details of the chosen queries, it is apparent that this technique has the potential to generate promising exploration activity that can engender new targets. Sommaire - Le développement de modèles 3-D géo-intégrés fiables implique l’intégration de grandes quantités de données géologiques publiques ainsi que des données lithologiques, structurales, géochimiques, géophysiques et de forages en provenance du secteur privé. L’industrie pétrolière dispose de modèles et de cartes 3-D depuis plus de 10 ans. Ce manuscrit présente un exemple d’utilisation de modèles et de cartes tridimensionnels détaillés comme outils interactifs dans l’exploration de dépôts métallifères. L’emphase est mise sur le processus d’interrogation des données en 3-D pour la définition de cibles d’exploration en profondeur. Les avantages principaux de cette technique sont l’uniformité du traitement des données et de la validation des interprétations géologiques, tout en tenant compte des données géophysiques et géochimiques. L’intégration de données et la corrélation de la géologie et de la géophysique peuvent être accomplies en deux dimensions dans n’importe quel logiciel SIG. La plus grande force de l’analyse 3-D demeure cependant la possibilité de construire des modèles complets et réalistes permettant de cibler des secteurs à haut potentiel économique en profondeur. De plus, ces modèles peuvent être modifiés et améliorés de manière interactive en ajoutant de nouvelles données provenant de forages et de levés géoscientifiques en cours. Ce manuscrit présente deux exemples de modèle 3-D géo-intégrés développés pour l’exploration minérale : le camp de SMV de Joutel et le camp aurifère de Duparquet, Québec. Dans les deux cas, la construction du modèle est décrite et les requêtes spécifiques à chaque type de gisement sont présentées. L’exercice a permis de définir huit cibles d’exploration potentielles à Joutel et sept à Duparquet. Bien que les cibles identifiées dépendent des contraintes utilisées pour les requêtes choisies, cette technique permet de générer de nouvelles cibles qui pourraient relancer l’activité d’exploration dans les camps miniers " matures " ou dans des secteurs moins explorés."

Jan 1, 2006

By D. J. W. Piper, T. Hundert, G. Pe-Piper

"Abstract - Potentially commercial deposits of kaolin are found in the fluvial Lower Cretaceous Chaswood Formation, the sedimentologically proximal equivalent of deltaic sediments of the offshore Scotian basin. The geological setting of the kaolin deposits has been interpreted from high-resolution seismic-reflection profiles and boreholes, and mineralogical studies on one reference borehole. The kaolin is a product of early diagenesis involving meteoric water below the water table. The distribution of kaolin is controlled by the presence of intraformational unconformities that were sites of ground water recharge, and are marked by the development of oxisols above the water table. Such diagenesis was facilitated by interbedded, loosely consolidated, permeable sandstone. The highest-grade kaolin deposits are found in areas close to river belts, where overbank muds were not sufficiently drained to develop paleosols, but where later uplift created intraformational unconformities. In the sandstone, meteoric water flow altered feldspars to kaolin, thus yielding commercial silica sand deposits. It also altered ilmenite to rutile, which is concentrated as secondary placers in modern rivers that have eroded the Chaswood Formation and tills derived therefrom. Sommaire - Des dépôts de kaolin potentiellement économiques ont été notés dans la Formation de Chaswood d'’âge Crétacé Inférieur, laquelle constitue un équivalent latéral en milieu fluviatile aux sédiments deltaïques du bassin de Scotian. Le contexte géologique de ces dépôts de kaolin a été interprété a partir de profils de seismique-réflection à haute résolution, de sondages, et d’études minéralogiques sur un sondage de référence. Ce kaolin est un produit diagénétique précoce formé par de l’eau météorique sous le niveau de la nappe phréatique. La distribution du kaolin est contrôlée par la présence de zones de recharge associées à des discordances intraformationelles marquées par le développement d’oxisols au-dessus du niveau de la nappe phréatique. La présence d’interlits de grès perméables faiblement consolidés a contribué à l’efficacité de ce processus diagénétique. Les dépôts de kaolin les plus riches se trouvent en périphérie des rivières, là ou les boues de la plaine d’inondation n’étaient pas suffisamment bien drainées pour permettre le développement de paléosols, mais où des mouvements verticaux subséquents ont crée des discordances intraformationelles. La circulation d’eau météorique dans les grès a entraîné l’altération des feldspaths en kaolin, générant ainsi des dépôts économiques de sable de silice. Elle a aussi causé l’altération de l’ilménite en rutile, que l’on trouve dans des placers secondaires situés dans des rivières contemporaines qui ont érodé la Formation de Chaswood et les tills qui en sont dérivés."

Jan 1, 2006

By D. Bois, P. Keating, J. Lemieux, M. A. Vallée, M. Allard, R. S. Smith, L. Z. Cheng, M. Chouteau, D. K. Fountain

"Abstract -A test survey using the MEGATEMII airborne electromagnetic system was flown over the Iso and New Insco massive sulfide orebodies in the Rouyn-Noranda mining camp, Canada. The results were compared with data from historical systems (INPUT, DIGHEM) used to discover the deposits. The historical data show that the two deposits have comparable conductances. However, the modern MEGATEMII system reveals that the New Insco deposit has a much slower decay than the Iso deposit, and it is, therefore, interpreted to be more conductive. The MEGATEMII anomaly maps provide estimates of the location, depth, dip, and strike of the two deposits, information that was not available from the historical anomaly maps. The signal-to-noise ratio of the MEGATEMII data is greater than the historical data, yielding more sharply defined anomalies. The investigations also included a comparison between 90 Hz and 30 Hz MEGATEMII data. The 90 Hz data were found to be useful for mapping the less conductive parts of the Iso body, whereas the 30 Hz data demonstrated that the New Insco body is more conductive. Analysis of height attenuation data over the Iso body indicates that the body could be seen by the MEGATEMII system if it were buried an additional 230 m deeper (in highly resistive material). On the other hand, the INPUT system would detect the Iso body only if it were buried no deeper than an additional 60 m. Tests with the transmitter turned off showed that, for this flight, the MEGATEMII system noise levels on the processed data are about 300 pT/s. Sommaire - Dans le cadre d’un projet de recherche, un ensemble de levés d’essais électromagnétiques aéroportés employant le système de MEGATEMII a été effectué au dessus des dépôts d’Iso et de New Insco, Rouyn-Noranda, Canada. Les données ont été comparées avec les réponses des systèmes qui ont découvert ces deux dépôts (INPUT et DIGHEM). Les données antérieures montrent que le dépôt d’Iso a une conductance comparable à celle de New Insco. Cependant, les données de MEGATEMII démontrent que le dépôt de New Insco a une haute valeur de la constante de décroissance, ce qui reflète une plus forte conductivité. La carte d’anomalies de MEGATEMII indique la localisation, la profondeur, le pendage et l’orientation des deux dépôts, ce que la carte d’anomalies antérieure ne montrait pas. Le rapport de signal à bruit de MEGATEMII est plus grand que celui des données de INPUT et de DIGHEM; de plus, les pics sont mieux définis. Les tests ont également permis une comparaison entre les fréquences de base de 90 Hz et de 30 Hz. Les données de 90 Hz se sont montrées utiles pour cartographier la partie du dépôt Iso dont la conductivité est la plus faible, tandis que les données de 30 Hz montrent clairement que le dépôt de New Insco est plus conducteur. Les analyses de l’atténuation du signal avec la hauteur ont indiqué que le dépôt d’Iso pourrait être détecté par le système MEGATEMII s’il était enfoui à 230 m sous la surface (dans un milieu hautement résistant). D’autre part, le système INPUT pourrait seulement détecter le dépôt d’Iso s’l était situé à 60 m de profondeur. Les tests avec l’émetteur fermé démontrent que le niveau de bruit est des l’ordre de ±300 pT/s."

Jan 1, 2006

By D. Bois, P. Keating, J. Lemieux, M. A. Vallée, M. Allard, R. S. Smith, L. Z. Cheng, M. Chouteau, D. K. Fountain

"Abstract - MEGATEMII airborne electromagnetic data collected over the Iso and New Insco massive sulfide deposits have been modeled using three modeling packages. The EMQ package is a quick inversion tool which indicates that the Iso body is a dipping, plate-like body. The New Insco body is inferred to have a geometry somewhere between a dipping plate and a sphere. The Maxwell package was used to refine the properties of the plate-like body at Iso. The EMIGMA package was able to identify which parts of the New Insco orebody were more conductive. It was observed that the most conductive parts correspond to copper-rich zones and the next most conductive to pyrite-rich zones. The EMIGMA package was also used to show that a thick-prism model might be more appropriate for the New Insco orebody. Gravity modeling constrained by the known geology was successful in identifying the denser sulfide zones. The densest zones appear to be pyrite rich. Magnetic modeling identified diabase dikes. Over New Insco, a small magnetic anomaly was attributed to pyrrhotite-rich sulfides. There was only a weak magnetic anomaly over the Iso body, consistent with the nonmagnetic sulfides logged in the holes drilled at that location. Sommaire - Les données MEGATEMII recueillies au-dessus des dépôts d’Iso et de New Insco ont été interprétées en utilisant trois outils de modélisation différents. L’outil EMQ a été utilisé comme un outil d’inversion rapide suggérant que le dépôt Iso peut être considéré comme une plaque inclinée, et que le dépôt de New Insco se situe quelque part entre une plaque et une sphère. L’outil Maxwell a été utilisé pour raffiner les propriétés du dépôt Iso. L’outil EMIGMA nous a permis d’identifier les différences de conductivité à l’intérieur du dépôt Iso. Il a été observé que la partie la plus conductrice correspond à la zone riche en cuivre, suivie par la zone riche en pyrite. L’outil EMIGMA a aussi permis de montrer qu’un modèle de prisme épais pourrait être plus approprié pour décrire le dépôt New Insco. La modélisation des données gravimétriques, contrainte par la géologie connue, définit bien la zone de sulfures massifs. La zone de pyrite semble être la plus dense. La modélisation des données magnétiques identifie bien les dykes de diabase. Au-dessus du dépôt New Insco, on observe une faible anomalie magnétique correspondant aux sulfures non magnétiques observés dans les carottes de forages à cet endroit."

Jan 1, 2006

By K. Hardy

As part of Inco's $115 million Fluid Bed Roaster SO2 Abatement Project, a new weak acid treatment plant (WATP) was constructed to treat bleed solutions from the Copper Cliff Smelting Complex gas-cleaning circuits. The WATP produces an iron-arsenic co-precipitate, termed "basic ferric arsenate" (BFA), which requires disposal in an environmentally acceptable manner. Following analysis of many potential options, the short-listed disposal alternatives were: A) Co-disposal of the BFA?gypsum sludge with rock tailings, a portion of which would be used in mine backfill, with the remainder being sent to the tailings area, and B) Co-disposal of BFA?gypsum sludge with pyrrhotite tailings in the tailings area. Testwork showed that the addition of BFA?gypsum sludge to mine backfill samples increased the uniaxial compressive strength (UCS) of the backfill for most samples, especially those at lower binder content ratios. Extensive analysis was conducted on samples taken from the Copper Cliff tailings area, where BFA?gypsum sludge from Inco's Copper Refining Electrowinning Department has been co-deposited with pyrrhotite tailings since 1990. Pore water samples from these areas contained very low arsenic concentrations, indicating that the arsenic had remained stable in that environment. Ultimately, co-deposition with pyrrhotite tailings was chosen as the preferred option for the disposal of BFA?gypsum sludge from Inco's new WATP.

Jan 1, 2006

By P. M. Daling

The objectives of this study were to examine a representative cross section of formal safety analysis techniques developed for the nuclear and aerospace industries, to recommend those methods that would be suitable for application to the mining industry, and to include those methods in a user's manual. Volume II of this report, the user's manual, describes several methods that were determined to be immediately transferrable to the mining industry. The handbook gives detailed instructions on appropriate application and utilization of the methods. Other techniques will require further development before they can be effectively transferred to the mining industry.

Jan 1, 2006

By A. R. Dover

The Richmond San Rafael Bridge (Figure 1) is a 4.3 mile long major toll bridge span across northern San Francisco Bay. Tutor-Saliba/Koch/Tidewater (TSKT) conducted a comprehensive seismic retrofit, which was at the time Caltrans? largest-ever construction contract at $484 million. The robust foundation retrofit design of 11 bridge piers included the installation of 26 new, large diameter (126 to 162 inch OD, wall thickness 1.5 to 2.25 inches) CIDH and CISS piles, with steel pipe piles installed to tip elevations of Elev. ?140 to -220 ft, in water depths up to 70 feet. The open-ended steel pipe piles had initial sections ranging from 71 to 172 feet long, with full lengths that extended to the bay bottom and then through 100 to 130 feet of marine sediments to top of bedrock. The marine soils of most interest consisted mainly of soft to firm Young Bay Mud (YBM), a silty, moderately-sensitive clay common to SF Bay. A key constructability issue was the prediction of pipe piles ?running? under self weight (198 to 625 kips in air) and pile driving hammer weight (IHC S-500 with total assembly weight of 322 kips). The term "pile running" is used to describe the penetration of the pile into the soil due to the self-weight of the pile only. This issue was critical because 1) there was limited head room under the bridge deck, and 2) if piles run too deep, the pile splicing on several piles would be problematic (the lowest desirable pile top elevation after running was +10 ft). While running measurements are sometimes made during marine/nearshore construction, there is little published data on predicted vs. actual running. This paper discusses the running prediction under self weight for 26 piles, and the methodology used in developing the predictions, which ranged from 15 to 94 ft of penetration below mudline. Pile running was recorded and compared with predicted values. The prediction methodology was quite good, and no significant constructability problems were encountered. The authors ?tweaked? the model to provide a slightly improved prediction method. The paper presents the model, predictions, observations, and discusses important lessons learned.

Jan 1, 2006

By W. A. Jankola

Teck Cominco Metals Ltd. operates an integrated zinc-lead smelter at Trail, British Columbia, Canada. The zinc circuit comprises three parallel operations: conventional fluid-bed roasting, direct zinc pressure leaching of concentrates and atmospheric leaching of zinc oxide fume recycled from the lead smelter. The products from these three areas are combined in the main leaching plant where they undergo iron purification. Unlike most leaching circuits, the leach process in Trail begins with an acid leach and is followed by a neutral leach. An evaluation was undertaken to determine if the process at Trail could be improved by converting to the conventional neutral leaching process with a subsequent acid leach of the residues. This paper explores the results of these tests and the implications for Trail Operations.

Jan 1, 2006

The emerging coal seam gas (CSG) industry has the potential to provide a large-scale energy province for Queensland. Aquifer impacts and management of associated by-product water, both in terms of quantity and quality, are pivotal considerations for the development of a sustainable CSG industry.Legislative changes have been introduced to ensure that the CSG industry manages potential groundwater impacts and beneficial reuse of the by-product water to a level acceptable to both government and the community.The relevant new pieces of legislation covering petroleum and coal seam gas activities include the Petroleum and Gas (Production and Safety) Act 2004 (P&G Act), Petroleum and Other Legislation Amendment Act 2004 (POLA Act), the Petroleum and Gas (Production and Safety) Regulation 2004 and the Petroleum Regulation 2004. Other relevant legislation includes the Petroleum Act 1923 (Petroleum Act) and Part 7AA of the Mineral Resources Act 1989 (Coal Seam Gas Regime). The P&G Act introduces a full regime for managing water rights. This includes provisions for monitoring and reporting on the effects that the taking of underground water under petroleum tenure has on other bores in the area. The P&G Act also imposes a æmake good obligationÆ on petroleum tenure holders, which requires the restoration of bores affected by the taking of water or the payment of compensation. These provisions represent a significant departure from the Petroleum Act, which says very little about water rights and does not specify restrictions on the taking of water under petroleum tenure. This paper attempts to outline the requirements and obligations of the P&G Act for the CSG industry in terms of underground water rights, development impact assessments, aquifer trigger thresholds, monitoring and reporting requirements, as well as the make good obligations.

Jan 1, 2006

LKAB operates two underground mines in Kiruna and Malmberget, Sweden. Blast furnace pellet is the main product and makes up 70 per cent of total production. The orebodies are hosted by 1910 - 1860 Ma old volcanic rocks. The host rocks and the ores were affected by the Svecokarelian orogeny for 1890 - 1860 Ma ago. The deposit belongs to the Kiruna type apatite-rich iron ore. Magnetite is the main ore mineral but haematite is the dominant ore mineral in some orebodies in the western part of the deposit. Large-scale sublevel caving is the dominant mining method. Three main haulage levels are in operation at present. The ore boundaries and quality can be detected by geophysical logging resulting in reduced waste dilution and subsequent grade reduction. The susceptibility measurements have been used in the magnetite ore since 1991 and gamma-gamma measurements in the haematite ore since 1998. The mining scale has increased during the last 20 years but diamond drilling has remained at approximately 18 000 drilling metres per year. Uncertainties in the ore constructions can lead to unexpected cost increases, ore loss and dilution. The ore boundaries are evaluated with percussion drill holes using in-hole geophysics to achieve satisfactory geological knowledge. The probes are calibrated in all currently mined orebodies. The correlation between core sample assays and measured susceptibility and gamma-gamma values is strong. The cost to determine the ore boundary by percussion drilling with in-hole geophysics is two-thirds lower, and productivity is six times higher compared to diamond drilling. The measurements are made by geotechnicians and the interpretations by a geologist. The results are transferred to a database and presented three dimensionally as holes with iron grade intervals on mine maps. The interpreted holes are used by the geologist in various ways in the geological modelling. Layout planning uses the measurements as a tool to place the drifts at the correct distance from the ore contact especially in the longitudinal sublevel caving and the production hole planning to optimise the final length of the cross-cuts and drifts for best ore recovery.

Jan 1, 2006

By J. Petit, P. Girard, A-M. Gilbert, D. Faucher

L&apos;annee 2000 a été une année stratégique et significative pour l&apos; Aluminerie de Bécancour dans la réduction des gaz a effets de serre. L&apos; équipe s&apos; etait donne comme defi un jour d&apos;arriver a l&apos;objectif de zero effet d&apos;anode dans les sa11es de cuve (720 cuves au total). Le cha11enge s&apos;averait tres ambitieux car la fa<;on d&apos;alimenter une cuve d&apos;electrolyse pour obtenir son maximum de rendement faraday est de travailler le plus pres possible de l&apos;effet d&apos;anode pour eviter l&apos;embourbement de ce11es-ci. Ceci signifie que techniquement nous a11ons en moyenne, quotidiennement, 12500 fois pres de l&apos;effet d&apos;anode sur !&apos;ensemble de nos 720 cuves qui produisent aujourd&apos;hui environ 405 000 tonnes d&apos;aluminium liquide annuellement. Des 695 kg equivalent en C02 par tonne d&apos;aluminium produite en moyenne annue11ement, de 1990 a 2000, nous en sommes rendus ace jour a environ 35 kg equivalent en C02 par tonne produite. Nous sommes pres d&apos; atteindre notre objectif mais les demiers gains sont plus difficiles a atteindre. Les strategies d&apos;automatisme et d&apos;informatique, incluant l&apos;aspect de !&apos;implication humaine sur les bonnes pratiques de travail sur les cuves d&apos;electrolyse, sont les cles de ces resultats.

Jan 1, 2006

By M. A. Nagle

Various strategic projects were carried out in 2002 to increase the capacity of Teck Cominco&apos;s integrated zinc-lead smelter at the Trail operations site in British Columbia, Canada. The lead smelter treats the iron residue from the zinc plant and optimizes the overall zinc recovery. This paper summarizes two options that were considered to reduce the zinc content in the leaching iron residue. The first option involved increasing the capacity of an existing hot acid leach circuit up to the iron loading constraints of the circuit. The second sought to maximize the hot acid leach capability by separating the ferrite-rich solids, followed by aggressive hot acid leaching (>100°C) and subsequent iron precipitation. Different forms of iron precipitation were reviewed in order to determine the most effective and economical approach. Among these, was a novel high temperature ferrite conversion process. The technical results and selection criteria are presented together with possible ways to integrate the process concepts into the current sulphide leaching plant circuit. The first option was selected for implementation and is currently being operated successfully.

Jan 1, 2006

Gold was discovered at Waihi in 1878. In 1987 the modern Martha Mine opened in the middle of the town of Waihi. Newmont Waihi Gold as the current licence holder has been operating the mine since 2000. The current open pit was scheduled to stop production in mid 2006. An underground mine is currently being developed to the east of the town. &nbsp; In 2001 serious subsidence issues from historical underground mine workings outside the mining licence and the forecast closure of the open pit acted as a catalyst for the development of new communication initiatives. &nbsp; In this context Newmont Waihi Gold and the Hauraki District Council initiated a community consultation process with the people of Waihi. The Waihi Community Consultation Committee (WCCC) was established in May 2003. After an initial brief to act as a forum for community participation in closure and rehabilitation of the Martha Mine, the group quickly took on a much more proactive role working towards the long-term social, environmental, cultural, economic and spiritual sustainability of Waihi. &nbsp; In the course of over three years of meetings all groups represented on the committee have presented their views, developed ideas and established an organisational structure to bring those ideas to fruition. The challenge now is to work together to consolidate likely options, seek sources of funding, produce business proposals and implement the plan for the future of Waihi. &nbsp; This paper backgrounds the experience to date and describes the outcomes of the process. For more detail on process considerations this paper should be read in conjunction with Part C by process facilitators, T Clark and S Stewart. For more detail on progress towards the groupÆs goals and future possibilities, this paper should be read in conjunction with Part B by Vision Waihi Trust CEO, E Morrow.

Jan 1, 2006

Pike River Coal Limited is in the process of developing the Pike River Coal Mine in the Paparoa Ranges of New ZealandÆs South Island. The mine will be developed to extract a coking coal deposit of the Brunner Seam, some 46 km north-east of Greymouth, using a combination of continuous miners and hydraulic extraction. The mining area is located within Department of Conservation (DOC) land and is adjacent to the escarpment of the Paparoa Range and the Paparoa National Park. &nbsp; As such, the major restriction to planned extraction is protection of: +&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; the western escarpment, +&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; vertical and sub-vertical rock faces, +&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; permanent water courses, +&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; significant vegetation, and +&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; steep slopes. &nbsp; The mine will use its elevation advantage to hydraulically flume coal from the working faces to the pit bottom area where it will be slurried to approximately 35 per cent density of solids and pumps down a slurry line to the coal prep plant some 10.5 km down the Pike River Valley. The coal will be sold on the export market as a high quality coking coal for international steel making.

Jan 1, 2006

By C Woodfull, S Munroe

Geological uncertainty is reduced by improved understanding of the relationship between regional-scale geological basement features (structure, composition, depth) and known local structural risk (such as recognised structural hazards at the mine). Coal mining and exploration entities can be more efficient and effective in managing geological risk at a range of scales. A more efficient and effective performance in forward interpreting and managing geological risk will result in a more efficient and effective exploration and also incremental or even significant mining cost improvements. In order to improve the understanding of basement features, a new 4D regional structural/basin framework for the Sydney Basin and the eastern part of the Gunnedah Basin has been constructed to provide primarily coal exploration and mining with a more integrated geological framework for ongoing subregional to mine-scale geological risk based studies. The model has been developed from a range of available regional geophysical and geological datasets, of variable detail and reliability, which have been brought together to generate a more robust structural and tectonic model than could be generated with any one single dataset. An initial regional structural model for the Sydney Basin was constructed in 2003 and an update to the model was released in 2005 (SRK Consulting, 2003; 2005). The development and ongoing refinement of the model was undertaken with financial and data support from a number of coal mining industry, gas exploration and government organisations. Prior to, and following the development of the regional structural/basin model and associated Information Base, a number of more area-specific studies have been completed, using the æbasement upÆ assessment approach. The methodology for developing comprehensive structural models, from the basement up, is outlined. The approach can be applied at a country-wide, regional or lease area scale. Case examples of where this approach has been used as an effective and efficient method in improving geological certainty and as a predictive tool to help manage geological risk are also presented.

Jan 1, 2006

By T. T. Chen

The iron- and elemental sulphur-rich residues generated during batch and continuous pressure oxidative leaching of Inco Limited&apos;s Voisey&apos;s Bay nickel sulphide concentrate at 150°C in sulphate-chloride media have been characterized by X-ray diffraction analysis and scanning electron microscopy. The residues produced during the continuous leaching of the pentlandite- and pyrrhotite-rich concentrate consisted predominantly of hematite and elemental sulphur, with minor amounts of goethite. Although the iron species generated in the batch leaching tests were similar to those formed during continuous leaching, the morphologies of the hematite and goethite particles were significantly different. In addition to the tiny spheroids and bubble-like particles, the hematite and goethite generated during batch leaching occurred as larger "hollow" shell-like particles that contained residual pentlandite or sulphur cores. Although the leach solution from which the iron oxides had precipitated contained 5-15 g/L sodium, sodium jarosite was detected only in trace amounts in a few of the leach residues.

Jan 1, 2006

By Hyun. I. Park

Although numerous investigations have been performed over the years to predict the behavior and bearing capacity of piles, the mechanisms of these behavior and bearing capacity of piles have yet to be entirely understood. Bearing capacity is difficult to predict, because it is affected by many parameters, which have complex relationship with each other. The present paper describes the application of Artificial Neural Network (ANN) in dynamic load tests to predict the resistance of driven piles. The tip, shaft, and total pile resistances can be predicted only for piles with available corresponding measurements of these values. The design methodology composed of ANN and genetic algorithm (GA) is applied to find the optimal neural network model to predict pile resistance. The results of this study indicate that the neural network model serves as a reliable and simple tool for predicting the capacity of driven piles.

Jan 1, 2006

By H. Vermette, J. Demers, R. Leclerc, P. Bergeron, P. Hudon, A. Lessard

The Arvida Smelter marked its 80th anniversary in 2006. Arvida currently operates 6 potrooms equipped with prebaked side-feeding pots producing 160 000t of aluminum per year, requiring the supply of 300 000t of alumina per year. In the past, to ensure reliable alumina supplies to the pots, especially in winter, a safety stock of alumina was kept inside the plant. The improved reliability of shipping on the Saguenay River has cut the need for such a stock. However, the stoppage of 8 Soderbergtechnology potrooms, starting in the 1980s up to 2003, generated alumina from the cleaning of pot pits, totaling 18000t and leading to the building-up of a significant alumina stock again. Concerns over working conditions, effect on potroom operations, and dust emissions prevented Arvida from tackling effectively this impressive alumina stock. Yet the increasing cost of alumina has created a strong motivation to use the stored alumina. In 2004 Arvida launched a project to recycle the stored alumina. This 4-year project aimed at clearing the alumina stock without affecting the operation of the smelter. It involved changing work organization, improving equipment and controlling the effect of the recycled alumina on the smelting process and working conditions.

Jan 1, 2006

By Peter Willbrandt

Norddeutsche Affinerie&apos;s routes date back to the 18th century. NA was established in 1866 as a joint stock corporation. NA&apos;s core business covers the production of copper cathodes from primary and secondary raw materials and the processing of them into wire rod and shapes. Part of the shapes are processed into pre-rolled strip and shaped wires within the Group. With some 3,200 well qualified and highly motivated employees, the NA Group produces some 560,000 tonnes of copper cathodes, 370,000 tonnes of wire rod, 230,000 tonnes of shapes, 130,000 tonnes of pre-rolled strip as well as 70,00 tonnes of strips and shaped wires annually. NA&apos;s product range is complemented primarily by precious metals, selenium, sulphuric acid, lead and nickel sulphate. The paper will give an insight into the performance of NA and its business units with regard to production, environmental and health protection and occupational safety.

Jan 1, 2006