Search Documents

By Y. He

Early research showed that the separation of particles based upon their density was not possible in steadily rising air streams. The terminal velocities of moving spheres are determined by their aerodynamic characteristics. This prevents particle separation by density in standard air classifiers. Passive pulsing air classifiers have accelerated airflow in certain regions, which achieves density-dominant separation. Numerical simulation of airflow within passive pulsing air classifiers was done to estimate airflow patterns near a damper. Analysis of those results shows the significant acceleration of the airflow above the damper. Laboratory trial separations have shown that passive pulsing classifiers are superior to standard air classifiers. Keywords: pulsing airflow, passive, simulation of airflow models, acceleration effect, density

Jan 1, 2005

By J. Huisman

With the introduction of ever-stricter environmental operating guidelines, capital expenditure restrictions and operational budget cutbacks, the biological method of SO2 removal becomes more and more attractive. Biological treatment of dilute flue gases is a more cost effective technology in comparison to conventional sodium hydroxide scrubbing. Although the investment costs for sodium hydroxide scrubbing is lower, the operational costs are significantly higher. In addition, the end product of the biological installation is sulfur instead of sodium sulfate; and no further wastewater treatment of the bleed from the biological installation is required since heavy metals are removed simultaneously. Another option for the treatment of SO2 containing gas at a sulfuric acid plant is the production of extra sulfuric acid of the discharged SO2 by applying an additional converter. Comparing biological treatment with this option shows much lower investment costs for the biological installation. Sulfur is produced which can be converted to sulfuric acid, so the bio-route will be more cost-effective than an additional converter. In principle, the biotechnological gas cleaning system is an integration of an absorber with a wastewater treatment facility. In the absorber, the SO2 containing gas is brought into contact with the washing water. The effluent absorber liquid contains a mixture of sulfite and sulfate that is converted into elemental sulfur. This conversion takes place in an integrated system; first, the sulfite/sulfate mixture is converted anaerobically into sulfide; secondly, the sulfide is converted aerobically into elemental sulfur. Subsequently the sulfur is separated and the water is returned to the absorber. Due to the buffer capacity of the washing water, removal efficiencies over 98% are possible. In addition to SO2 removal, it is possible to convert for example other bleeds streams such as scrubber acid or weak acid to sulfur in the same SO2 installation. Recent evaluations concluded that biological desulphurization of flue gases is not only economically attractive in comparison to convention sodium hydroxide scrubbing but also in comparison to gypsum producing systems and even seawater scrubbers. This paper describes the technological and economical viability of biological flue gas desulphurization.

Jan 1, 2005

Large areas of ground are permanently supported on coal pillars, both in extensive old workings and current drivages in active mining operations. Continued growth of civil infrastructure is resulting in more surface development above old bord and pillar mines and an increased need for mine development beneath existing surface structures and features. The result is a greater likelihood of conflict between miners, developers and regulatory bodies. However, over the last 40 years there has also been significant improvement in the general level of understanding of pillar behaviour and stability, both in Australia and overseas. This paper examines some of the issues to be considered when undermining surface structures or undertaking surface development above old workings. The Factor of Safety (FoS) methodology widely employed for the assessment of pillar stability is reviewed, including the key geometrical, geological and statistical concepts associated with the probability of pillar failure; local and international experiences are examined and significant parameters isolated. Common concerns are addressed in the context of actual practical experience, utilising a risk management approach. Recent advances in methods for the assessment of pillar stability are put forward, along with criteria for arriving at rational design outcomes.

Jan 1, 2005

By C. Musingwini

In the past ten to fifteen years, many organizations have applied business process re-engineering (BPR) to significantly improve their business competitiveness or stave off closures. The mining industry in Southern Africa is no exception and documented examples can be drawn from South Africa. Although the concept is superficially simple, its application has been marked by a high failure rate of about 70 per cent because it has been generally misunderstood. Shabanie mine, a chrysotile asbestos fibre producer in Zimbabwe took cognisance of this fact by cautiously embarking on a modular BPR programme in October of 2002. A year was used as a complete cycle or module for re-evaluation of the programme. Shabanie mine adopted BPR as part of management efforts to remain competitive amid serious threats to operational viability. These threats included hyper-inflation driven rising production costs, a declining world asbestos market and a possibility that Russia could take over the shrinking world asbestos market by dumping low-priced asbestos fibre. The only competitive advantage that the mine had was the high quality of its long-fibre chrysotile asbestos. The major BPR thrust was therefore to redesign processes for improved productivity and ultimately achieve a lower cost per ton of final asbestos fibre product. In addition, corporate culture change and cost-saving were also factored into the programme. This paper discusses the implementation experience of the BPR programme at the mine. The main BPR beneficial highlights are improved productivity, sizeable cost-savings, positive corporate culture change and identification of secondary projects. One of the lessons learnt from this programme is that mining companies will have to deal with the HIV/AIDS pandemic if they are to sustain high levels of productivity into the future.

Jan 1, 2005

By M J. Schultz, R L. Rude, D M. Tomko

The US Mine Safety and Health Administration (MSHA) conducted compliance assistance diesel particulate matter (DPM) sampling throughout the underground metal and non-metal mining industry. Based on that sampling, MSHA identified mines that were having difficulty meeting the DPM limit. To provide further assistance, MSHA then visited approximately 60 of the mines that were experiencing difficulty complying with the DPM standard. As part of these visits, DPM exposures were measured and control technologies for DPM were observed and assessed. Controls consisted of ventilation, clean engines, environmental cabs, alternative fuels, diesel particulate filters (DPF) and work practices. The focus of the follow-up compliance assistance visits was to assess control effectiveness and to make recommendations to mines experiencing difficulty in meeting the DPM standard. At each mine visited, the ventilation controls were evaluated, engine emissions were determined for equipment in use, environmental cabs were examined, and operational practices were noted. Additionally, control technologies, including alternative fuels and DPF were evaluated in several mines. A comparison was made of mine and section airflow to equipment particulate indices. Based on engine emissions, horsepower and operating time, the contribution of individual engine emissions to total emissions was made. Environmental cab integrity, positive pressure and air filtration systems were checked and operational practices relating to DPM exposure were assessed. This paper summarises the preference and magnitudes of controls that were typically used or needed for successful control of DPM. Additionally, results of the assessments of alternative fuels (including bio-diesel and water emulsion fuels) and DPF are presented.

Jan 1, 2005

This paper summarises the current status of the mining sector in Poland in terms of vertical transport system safety. Selected results of research programs conducted at the AGH-UST relating to mine hoist system safety are reviewed. The conclusions support the notion that the costs of vertical transport systems can be reduced, while at the same time maintaining the required safety and reliability levels. Novel solutions: movable fender beams HWR, linings modar« and the integrated shock absorbers PHH for conveyance guiding systems fully confirm this hypothesis.

Jan 1, 2005

By Roger Holmberg, Donald Jonson

The Swedish Standard SS 460 48 66, “Vibration and shock - guidance levels for blasting induced vibration limits”, is based on more than 50 years of experience from blasting close to structures and tunnels. The Swedish Standard gives a method for calculation of guidance values for different types of buildings and ground condition under the building. This is done for every building and structure within a predetermined zone. The guidance levels are for the peak particle velocity monitored in vertical direction. The standard is valid for all kinds of blasting project (tunnelling, quarrying, mining etc.) The guidance levels neither take in to consideration discomfort for people inside the building or structure nor vibration sensitive equipment inside the structure. The paper also presents the Swedish Standard SS 02521 “Vibration and shock - Blast induced airborne shock wave - Guidance levels for buildings”.

Jan 1, 2005

By P Trout, B Macaulay

Ridgeway Gold Mine (RGM) is an underground sublevel caving (SLC) operation that is owned and managed by Newcrest Mining Limited (NML). Production drill and blast practices are critical to the success of the SLC method at RGM. SLC production ring precharging was introduced in November 2001 to enhance these practices and deliver safety, productivity and cost improvements. Current precharging practices require up to two rings to be loaded ahead of the ring to be blasted in each drawpoint. The explosive may be required to remain in the up-holes for periods of four weeks or more prior to blasting. During this æsleepÆ time it is subjected to repeated shock from the blasting ofadjacent rings and from rings in adjacent drawpoints. The project described in this paper was designed to gain an understanding of the factors affecting explosive performance in the precharging environment and to develop explosive products and operating practices that would meet RGMÆs requirements in terms ofsaf ety, reliability and blast outcomes. Several months oflaboratory and field testing were required to characterise the explosive and quantify the effect of post-loading blasting shock. These results were used to determine the most appropriate loading and sleep time criteria for RGMÆs precharging practices. In addition, the information is being used to guide the development of the next generation of emulsion explosives for use in underground precharging operations.

Jan 1, 2005

By Davis. B. R.

There are a number of hydrogen storage systems proposed for automotive applications. However, all of the current suggestions fall short of the DOE targets for storage density and volumetric density. The DOE has suggested that only through radically new ideas will a practical solution to hydrogen storage for automotive applications be realized. This paper provides some background in chemical hydrogen storage and discusses roadblocks to the implementation of some proposed technologies.

Jan 1, 2005

By K. Janghorban

Multilayered ceramic-metal composites were produced by solid state diffusion bonding of polycrystalline alumina and three Al alloys containing 1 to 2%Sr, 2% Mg and Mg + Si (5057 Al alloy), The multilayered structures were fabricated at 610°C under a compressive stress of 3 MPa for 2 hours in He-5%H atmosphere, The ceramic-metal interfaces were studied by SEM and TEM equipped with energy dispersive spectrometer (EDS). Addition of 1 wt % Sr to Al promoted good adhesion, without producing any interfacial products, while the Al-2%Sr was poor in this regard due to the presence of dispersed A14Sr which is an intrinsic phase in the Al-Sr phase system, The Al-2%Mg alloy produced a continuous film at the interface, which was characterized to be MgAl2O4. Al alloys containing Mg and Si (5057 commercial alloy) produced not only the spinel structure (MgAl2O4), but another phase rich in Mg and Si (close to Mg2Si), These latter interfacial reaction products were not the intrinsic phases in Al-Mg alloys, and were reaction products at the Al2O3 ?Al alloy interfaces.

Jan 1, 2005

By Alastair Grogan

In October of 2002, the author was retained by Public Works and Government Services Canada, on behalf of the Department of National Defense, to design, construct and test the effectiveness of a bubble curtain system at an underwater demolition range, near Victoria, BC. The purpose of the bubble curtain was to reduce the potential for fish mortalities at the site. This paper presents some of the elements of the design, along with the results of overpressure monitoring during blasting and compares the results of fish mortality and animal behaviors with and without the bubble curtain in operation.

Jan 1, 2005

By Russell Frith

Probably the most expensive but least well understood roof falls in underground coal mining, are those that occur ahead of the powered supports in the centre of longwall face. Even small roof cavities result in the dilution of the ROM product and large cavities can stop the face for days if not weeks and the incurred cash flow losses can be catastrophic. Expensive and time-consuming remedial measures (e.g. PUR, cavity filling, removal of stone from the AFC by hand) are required and equipment wear and damage can be significant when the need to blast and convey stone is also considered. Through four major research projects within the Australian coal industry and numerous consulting assignments, the author has spent the best part of fifteen years attempting to identify and defme the various geotechnical and operational factors that determine whether a major roof cavity occurs ahead of the powered supports or a normal goaf fall occurs just behind them, the difference in operational outcome being enormous. The paper presents a condensed summary of the overall technical findings covering such issues as roof fall mechanisms, the measured influence of cover depth, periodic weighting of massive strata units and its quantification, the role of cut-throughs in chain pillars, face width and height, the role of the powered support and the influence (both positive and negative) of mine site operations. The big picture outcome is the view that high production longwall extraction is well-suited to certain geotechnical environments, is marginal in others and under certain conditions is fatally flawed and beyond the control of mine operators, although fortunately the latter category is a relatively rare situation. Various risk-based research findings in this regard will be given as a basis for future discussion.

Jan 1, 2005

By David M. Jurich, Randy J. Essex, Alex de Aboitiz

An Automated People Mover (APM) transit system is planned for the growing Phoenix Sky Harbor International Airport. The APM will improve passenger movements between the terminals, and provide a link to parking facilities, a new rental car facility, and the planned metro Light Rail. The underground works will include shallow twin bored tunnels, taxiway crossings, and underground stations constructed beneath critical airport facilities. Challenging soft ground conditions will require extensive underpinning and ground improvements. Design is underway, and construction is scheduled to begin in 2007 with project completion in 2015. The owner’s planned delivery method for the APM Project will be Construction Manager at Risk (CMAR) with a Guaranteed Maximum Price.

Jan 1, 2005

Paper written on project work carried out in partial fulfilment of BSc Engineering (Mining) The aim of this project is to determine whether certain pillars occurring within the no. 1 shaft and no. 2 sub-shaft ground are feasible for extraction. The extraction of these pillars is essential in prolonging the life of Kloof Main Shaft as its VCR resource becomes depleted. Extraction of these pillars will require a combination of designs and factors, with rock mechanics and ventilation being the main considerations. Primarily for the pillar extraction, an initial production target of150 kg gold, mine able in one year from commencement of ?opening up? was set. The planned target has been exceeded and the feasible pillars identified are expected to yield an additional 1 390 kg of gold to the shaft?s production profile. However, not all the required ventilation designs have been completed to date, the reason being that at the time of the project, many of the pillar areas were inaccessible and thus ventilation conditions are unknown. This project is therefore an ongoing process and will require further design once all targeted pillar areas have been opened up. A preliminary costing analysis of the pillar mining was performed and it was found that all targeted pillars with the exception of 38?61 pillar are profitable.

Jan 1, 2005

By Gale L. Hubred

Kennecott?s Ledgemont Laboratory developed the Cuprion Process to recover metal values from manganese nodules in the early 1970s. A reducing leach of monovalent cuprous ion attacks the manganese oxide matrix, converting the manganese dioxide to manganese carbonate and releasing the copper, nickel, cobalt, and zinc as ammine complexes. Cuprous ion is generated by contacting leach liquor with carbon monoxide. Copper, and nickel, are recovered by solvent extraction and electrowinning. Cobalt is precipitated as cobalt sulfide and recovered as cobalt powder. Manganese, molybdenum, and zinc can be recovered optionally but have not been included in this process. Kennecott authors have described aspects of the process, but the Cuprion process has not been revealed except in patents. Tables are included for capital and operating costs and revenue. Even though economic recovery of nodules is not anticipated in the foreseeable future, some of the process steps may have application in other places. The Ledgemont Laboratory was a unique operation we think worth documenting. The report is based upon work done up until the mid 1970s. The report represents the work of the entire Kennecott nodule team. It is this author?s intention to save this result and credit the work of that nodule team. The paper is dedicated to the memory of Dr. Herbert Barner, a key member of the team who died in 2003.

Jan 1, 2005

By A. Subbotin

During developing the Ingulska mine at the Mi-churinske uranium deposit in the central part of Ukraine the radioactive rock dumps have been piled. A height of dumps reaches to 15-25m. They occupy a large territory and can be a source of covering with radioactive dust the area around the Ingulska mine. Uranium content exceeds 0,01% in all dump rocks samples while in the dust fraction samples it ranges from 0,01 to 0,06%. Uranium content in road dust at the dump?s foot reaches 0,137%. A new (for Ukraine) method of f-radiography of tree and bush leaves sampled at the territory about 100km2 has been used. It is based on fission of 235U nucleuses due to heat neutron influence in a nuclear reactor and on following study of the Lausan films with tracks drawn by the fractures of these nucleuses. Uranium content of the dif-fusion-disseminated dust type is (0.9-22.2)?10-6% while in the individual particles it can be considered much more because of burned holes in Lavsan above them. The dust content with uranium in Kirovograd reaches to 20-50 part/cm2 while near the dumps it ranges from 100 part/cm2 to 300 part/cm2 in the radius of 1,5-2km from the Ingulska mine.

Jan 1, 2005

By J-P Franzidis

A technique for determining the recovery of attached particles across the froth phase in flotation that relies on measuring the rate at which bubble-particle aggregates enter the froth is used to investigate the selectivity of attached particles across the froth phase. Combining these measurements with those of other techniques for determining the froth recovery of attached particles provides an insight into the different subprocesses of particle rejection in the froth phase. The results of experiments conducted in a 3 m3 Outokumpu tank cell show that the detachment of particles from aggregates in the froth phase occurs largely at the pulp-froth interface. In particular it is shown that the pulp-froth interface selectively detaches particles from aggregates according to their physical attributes.

Jan 1, 2005

By K. Bounou, K. Komnitsas

"Risk quantification may be used as a sustainable development index in the mining industry, since it encompasses both economic and social factors. In addition, it may assist in the development of a framework, which is also indirectly related to sustainable development, to prevent accidents and improve health and safety standards. However, risk quantification in the mineral sector involves diverse activities and is considered a very difficult task. Although statistical data report accident severity rates, incident rates and accident frequency rates, none of these allow for accurate risk calculations. In this paper, two risk calculation formulas, which may be used to quantify risk, as well as to identify hazardous activities in a workplace, are proposed. Numerical examples are given based on statistical data available through the MSHA database. Also a combination of a decision/fault/event tree that allows risk quantification is presented."

Jan 1, 2005

By Lawrence F. Johnsen, Marc J. Gallagher

"Micropiles are small diameter, bored, grouted-in-place piles incorporating steel casing and/or reinforcements. The omission of micropiles from most United States building codes has resulted in the application of varying standards for design and installation. The ADSC/DFI Micropile Committee has developed a proposed section for the 2006 edition of the International Building Code (IBC 2006) covering micropiles. The proposed IBC 2006 micropile code section is presented, along with comparisons to existing micropile codes and guidelines. A discussion section is provided to clarify sections of the proposed code. IntroductionMicropiles, defined as small diameter (typically less than 12 inches outer diameter), bored, grouted-in-place piles incorporating steel casing and/or reinforcements, are becoming common foundation elements for new construction, retrofits, and emergency repairs. Developed in Europe in the 1950's and used in United States practice since the late 1970's, micropiles are typically not addressed in building codes, particularly in the United States. As a result, micropiles are often reviewed by building officials to a variety of standards, including drilled shafts, caissons, cast-in-place bored piles, and concrete filled pipe piles. None of these adequately address the unique design and construction aspects of micropiles. Therefore, it became apparent to the foundation design and construction community that a micropile-specific code section was required.To that end, the International Association of Foundation Drilling and the Deep Foundations Institute (ADSC/DFI) Micropile Committee appointed a subcommittee in October 2003 to develop and submit a proposed micropile code section for the 2006 IBC. The subcommittee members included the two co-authors, as well as Tom Richards (Nicholson Construction Company), Tom Armour (DBM Contractors, Inc.), John Wolosick (Hayward Baker, Inc.), Allen Cadden (Schnabel Engineering) and Matt Niermann (Schnabel Foundation Company). At the time of the writing of this paper, the proposed code section has been presented at the IBC public hearing during which it was modified slightly. Final adoption (or rejection) will be determined by the IBC at the final action hearing in September 2005. The attached code section is the revised version following the public review hearings."

Jan 1, 2005

Problems associated with gas management become more significant as exploitation of coal reserves in the Bowen Basin in Australia becomes deeper. At Oaky North mine, relocation of production from one area of the mine to another with a higher gas content required the use of pre-drainage, post drainage and inertisation techniques to enable production activities to continue largely uninterrupted. Innovative surface to inseam drilling techniques were developed for pre-drainage of reserves close to mine workings and have proven to be largely successful. The gas management techniques adopted and specific experience gained are discussed in this paper.

Jan 1, 2005