Search Documents

By Anton Sroka

The dimensioning of shaft safety zones is a substantial task of mining subsidence engineering. On the one hand, the coal reserves in shaft proximity are to be mined as complete as possible, because they can be made accessible economically. On the other hand, the maintenance of the shaft operation is to be ensured at each time, since shafts represent the most important link between underground and aboveground. Regarding these two criteria, this publication presents a model for the optimization of shaft safety zones. Beyond that, extraction methods in shaft safety zones are described, in particular with consideration of minimized mining influences on the shaft.

Jan 1, 2005

By Guangyi Sun

Wall rock classification method for coal mine support is the main factor affecting mine support. It is greatly affected by the combined effect of randomness, fuzziness and human being's incomplete knowledge. There are several coal rock classification methods. Using different rock classification methods the same engineering rock mass can be classified into different classification leading to different construction practices.

Jan 1, 2005

By P. Sauriol

This work addresses the design challenges and demonstrates the capabilities of a novel water transfer factor measurement apparatus. Several measurement concepts were screened on the basis of their water transfer factor accuracy using Monte-Carlo generated virtual experiments. The most promising measurement concept was assembled and tested to assess its actual measurement accuracy. For these concept validation experiments, the polymer electrolyte membrane fuel cell was simulated by adjusting the water injection rate to corresponding levels. Combining the anode and cathode measurements, the water transfer factor accuracy was typically better than 0.01. Real-time measurements of the water transfer factor on both anode and cathode sides of a polymer electrolyte membrane fuel cell were achieved. The anode and cathode side measurements were in good agreement with each other; however the anode side measurements were generally more reproducible. A parametric study showed that stream humidification plays an important part in the water transfer across the membrane electrode assembly. Finally the water transfer factor along the channel of a 300cm2 co-current fuel cell was obtained by using a series of six 50cm2 sub cells. The results were in good agreement with predictions from a recently proposed model.

Jan 1, 2005

The implementation of a process information management system (PIMS) is to provide a single online, real-time information system. This system provides a unique and completely open view for everyone, based on the key business drivers. It is structured around the three key concepts: process, maintenance and stocks. It combines numerous applications and provides accessibility to common tools and reports, through a web-based user interface, for every one from the floor operator to the General Manager. This æunique and commonÆ view displays raw, online process information that provides a quick health check of the operation at a glance, highlighting areas that require further investigation. The system is based on a hierarchical system of views, from the overview of the whole plant flow sheet to the more detailed operational shop view. It provides a synthetic view between continuous and batch operations, enabling the tracking of each batch produced. The batch view displays the critical batch components, and a comparison with each component of an ideal batch. This enables detailed analysis of each batch to identify areas of improvement. The information system will consist of an online reconciliation of stocks and flow data. This enables focus on the recovery of each process unit on a regular basis. This paper discusses the design strategy for the Process Information Management System, to ensure a unique and open view on the key business drivers is achieved and implemented successfully.

Jan 1, 2005

By Scott Chesman

Increased TBM performance is leading the way for resurgence in tunneling activity in NYC. Tunnels will be excavated in the same geologic formations as previously excavated D&B tunnels whose construction records are providing valuable insight into the prediction of rock mass behavior. This report compares an eight mile stretch of NYC Water Tunnel #2 with the recently excavated eleven mile stretch of the TBM driven Water Tunnel #3. Comparisons of the type and amount of rock support installed as well as water inflows and grout quantities are made. Rock mass characteristics specific to TBM performance are also evaluated.

Jan 1, 2005

By Paul Hewitt, Tim Smirnoff

Design and construction of the Epping to Chatswood Rail Line tunnels in Sydney, Australia required an innovative approach to define hydrogeological properties of the Sydney Hawkesbury Sandstone and provided an insight into the hydraulic behaviour of fractured sedimentary rocks. To meet restrictive water inflow and infiltration criteria both the pre-treatment of zones of fractured or highly jointed rock, and waterproofing using an interior spray on membrane for the finished drained tunnels and stations was required. Methods typically used to address the interaction of groundwater and tunnels in the Sydney Basin are demonstrated by case histories from major design-build tunnel projects.

Jan 1, 2005

This paper reviews ore pass practice in some Canadian mines in Quebec and Ontario. In particular it reviews ore pass configuration, flow control mechanisms and monitoring practice. A review of the type of problems encountered and the tools to restore flow is also presented.

Jan 1, 2005

By Andrew Wessman

Keywords: Recycling, Electrodeposition, Recovery, Dilute, Dissolved Metal Ions In order to facilitate the recovery of pure metals from solutions containing a mixture of dissolved metal ions, a pulsed electrodeposition method was developed. Using this method, it is possible to selectively remove metal ions from solution based upon the electrochemical potential of the particular ion desired. The use of pulsed electrodeposition rather than direct current electrodeposition creates an electrodeposited material with better morphology, increases electrical efficiency of the process, and avoids problems with short circuiting between electrodes. Using this method, it is possible to recover dissolved metal ions in a purified form in one simple step, and therefore maximizes recovery of the metal ions while obtaining them in a saleable form. This method is likely to be useful in improving the recycling process for numerous complex metal mixtures and alloys.

Jan 1, 2005

By Ronald E. Heuer

A 1995 RETC paper of similar title presented a method for estimating rock tunnel water inflow based on semi-empirical correlations with borehole water pressure tests. Since that time the author has found the method to be very useful, and it has been used by others in the industry. This current paper is an update which is intended to: A. More clearly explain assumptions and limitations of the method. B. Describe some case history examples. C. Respond to questions which have been raised; and extend the method to other considerations including distribution of inflow along the tunnel, panning requirements, interpretation of tunnel probe hole water inflow, and estimation of potential effectiveness of pre-excavation grouting to reduce water inflow.

Jan 1, 2005

By P Dare-Bryan

Many mines have an interest in improving fragmentation at their sublevel caving operations in order to produce better ore recovery, lower dilution and less overbreak. The primary requirement for the extraction phase is to understand and optimise the flow of the fragmented rock in the rings including interactions with the caved material. Rock fragment formation is critically controlled by the blasting phase and can potentially be improved by optimising the dynamic energy distribution throughout the ring through the crafting of explosive charging, priming position and initiation timing. The modelling of fragmentation and damage due to explosive loading of complete rings is inherently and irrevocably a three dimensional problem that is difficult to address. We have therefore initially utilised an analytical code to predict vector peak particle velocities and energies that are restricted to the plane of a ring. Dynamic energy distributions based on common timing and priming practice have been compared with other possibilities using conventional pyrotechnic detonators as well as initiation designs based on accurate electronic detonators. The energy distribution can be quite subtly tailored to increase energy in appropriate regions or to decrease energy in the brow region for example to potentially reduce instability and the probability of misfires. We have also recently developed the capability to efficiently model particle flow using four-sided polygonal elements. Despite the 2D limitations of such a model this results in more realistic fragment interaction and stacking than can be achieved using conventional rigid circular elements. Modelling of a typical sublevel caving ring utilising these elements activated by the correct dynamics offers considerable potential for understanding the influence of the blasting energetics and timing on the complex flow and extraction process.

Jan 1, 2005

By P. K. Naik, B. Das

Flotation studies were carried out to recover carbon values from blast furnace flue dust containing ~30.34% carbon, 4.6% volatile matter (VM), and 65.03% ash. The variables chosen for the experiments were dispersant (sodium hexametaphosphate), pH, collector (diesel oil), and frother (MIBC). The experiments were designed according to a 24 full factorial design method and regression equations for the recovery of carbon and product grade were determined from the data. Experiments were performed to optimize recovery and grade using the steepest ascent method. The maximum recovery of carbon was 90.0% with a concentration of 56.5%, whereas the maximum obtainable grade of carbon was 66.35% with 50.45% recovery.

Jan 1, 2005

"The application of telerobotics to mining is currently being introduced into production systems around the world. Mining companies in Canada, Sweden, South Africa, and Australia have tended to lead the international charge to this form of technology for mining. While this introduction is taking place, a few basic questions have yet to be answered. How many machines can a single operator run? How many types of machines can a single operator run?A Canadian Research Chair in Robotics and Mine Automation has been established at Laurentian University to investigate these questions and many more through a series of experiments in a telerobotics laboratory that connects Laurentian teleoperation workstations to model mining machines at Cambrian College’s eDome. The laboratory supports many experiments allowing researchers to physically run multiple robot scenarios differing the numbers and types of machines at one quarter scale. Further experiments are being designed to investigate the potential for managing time delays in telerobotics. This paper describes the laboratory, experiments, and some preliminary results."

Jan 1, 2005

By R Balusu, P Humphries

In combination with detailed field studies and goaf gas characterisation, computational fluid dynamics (CFD) models have been used to develop optimum and effective strategies for inertisation during longwall sealing operations to achieve goaf inertisation within a few hours of panel seal-off operation. This study has combined detailed analysis of the performance of various inertisation field trials together with CFD modelling results of different inertisation operations in order to develop the optimum inertisation strategies. A number of parametric studies were conducted on the base case CFD models that had been calibrated and validated based on the information obtained from previous inertisation studies and goaf gas monitoring. These studies included changes in inert gas injection locations, inert gas flow rates, seam gradients, and different inertisation strategies to investigate their effect on goaf inertisation. Studies indicate that the strategy of inert gas injection through the MG seal was not as effective as the alternative strategy of inert gas injection at 200 m behind the face. Innovative inertisation strategies have been developed and subsequently implemented at an underground coal mine in Australia. Further investigations have been carried out in the development and demonstration of proactive inertisation strategies with the objective to suppress the occurrence of spontaneous heatings in active longwall faces, in particular under unexpected scenarios such as during slow retreat/face stoppage due to difficult geological conditions. Initial trials at two Australian longwall panels have demonstrated the great potential of this practice to contain the onset of heatings in the goaf.

Jan 1, 2005

Sapporo-Iwanai district is located at the intersection of the northeast Japan arc and Kuril arc, associated with the subduction zone. This area is characterized by Miocene submarine volcanism followed by Plio-Pleistocene subaerial volcanism.   Koryu, a small epithermal Au-Ag deposit, occurred in Pleistocene (1.4 - 0.85 Ma) within Miocene sedimentary rocks near a subaerial andesitic volcano, while Toyoha, a large epithermal Pb-Zn-Ag (-Au) deposit, also occurred near a subaerial andesitic volcano. Although most of the base metal deposits formed in middle-late Miocene, Toyoha formed in Plio-Pleistocene (2.93 - 1.60 Ma) within Miocene volcanic and sedimentary rocks. This epithermal mineralization was partly overprinted by xenothermal Cu-Sn-In(-Au) mineralization (2.68 - 0.49 Ma).   Hydrothermal alteration differs vastly between Koryu and Toyoha: host rocks at Koryu were not intensively altered, although wall rocks adjacent to veins were silicified, while those at Toyoha show intensive and extensive neutral-pH alterations. Geological and chronological studies show that middle~late Miocene (12.5 - 8.4 Ma) alteration was pervasive and overprinted by Plio-Pleistocene (2.93 - 0.49 Ma) alteration. The base metal veins in the middle-late Miocene were not well developed, but were large in number with great depth.   These studies show that the hydrothermal activity at Koryu is rather small and short-lived, while that at Toyoha is large, long-lived and characterized by overprinting of different hydrothermal systems. The subaerial magmatic activities yielded not only the andesite lavas, but also generated hydrothermal solutions for the formation of both Koryu and Toyoha. The metals were possibly derived from such magma. At Toyoha, the hydrothermal solutions could also remobilize metals from old ores.   The size, life span of magmatic-hydrothermal system, and overprinting on the old mineralizing systems could constrain the type of metal deposits (precious and polymetallic deposits) nearby subaerial andesitic volcanoes in Plio-Pleistocene.

Jan 1, 2005

By M Donatelli, E Grazio, A Heissenberger

The distribution of a contaminant in a bulk mass greatly influences the effectiveness of sampling procedures. Most currently used sampling guidelines for genetically modified organisms (GMO) testing have stringent distribution requirements. Specifically, all these protocols are based upon the assumption that GM material, if present, is randomly distributed. Yet, assuming randomness is risky because the applied sampling plan may not provide an accurate estimate of the content of the contaminant. Despite the general consensus that an evaluation of the possibility of non-random distribution of GM materials within lots is a pre-requisite for the definition of effective sampling protocols, no experimental data on the distribution of GMOs in kernel lots are available anywhere in the world. Additionally, to date there is no distribution-free statistical model to estimate sampling errors, thus making the theoretical definition of optimal sampling technique impossible when randomness cannot be assumed. Here we present preliminary results of the KeLDA project, which is the first study investigating the distribution of GM materials in large soybean lots imported within the European Union. The extensive variability of GM content, observable both within and among soybean lots, indicates that heterogeneity issues cannot be overlooked when defining sampling strategies for large lots of particulate material and that randomness cannot be assumed a priori. A new statistical model free from any distribution assumptions, developed in order to estimate the sampling error associated with different sampling protocols together with the risk of false-negative results, is also presented. The new model, which is applicable to any consignment of particulate material with respect to any kind of contamination, presents two novelties: first, freedom from any distribution assumption; second, the possibility of estimating the magnitude of the sampling error associated with different sampling protocols as a function of specific distributional properties.

Jan 1, 2005

By G. Wozniak, R. Rostanski, H. Pfanz, G. Aschan, E. Sierka

"Industrial wasteland is a typical element of the landscape of all the industrialised regions in Europe. There are many examples from Poland as well as from other European countries that post-industrial sites have been undergone natural colonisation and succession to establish in some cases ecosystems of greater biological diversity than the original ecosystems. The post-industry sites regardless of any reclamation carried out, undergo natural successional processes. The respective biological diversity (number of species, and number of plant assemblages) reflects the micro-variety of the specific habitat. This paper summarizes the results of investigations, which have been carried out since 1989 on coal mine water sedimentation pools in the Upper Silesia Industry Region. The aim of this study is to demonstrate the diversity of spontaneous plant communities recorded on post-industrial waste sites. In the course of the long time fieldwork, plant assemblages representing nine phytosociological groups have been identified."

Jan 1, 2005

By S P. Suthers, J M. F Clout, J J. Campbe

An advanced technique for modelling hydrocyclone separation performance has been developed. This technique is based on the combined modelling of hydrocycloning parameters and ævirtualÆ iron ore feed. The virtual feed modelling was performed using a novel (in-house) software package called æRecognitionÆ, which uses data from optical image analysis to classify the particles in certain size fractions according to total iron content and calculates data for every grade class. These data include the average mineral composition and density of every liberation class in every size fraction. This information about every size fraction, representing the ævirtual feedÆ, was input to the mineral processing modelling package USIM PAC. The hydrocycloning process was then modelled for this virtual feed using the Plitt hydrocyclone model. Empirical calibration coefficients for the hydrocyclone model were calculated using an optimisation procedure in Excel. Pilot-scale hydrocyclone beneficiation experiments were performed on an iron ore blend, using different hydrocyclone pressures and per cent solids in the feed pulp. These experiments were modelled and the modelling results were compared with the experimental results. The new modelling approach enables prediction of the recovery of each mineral in the products, calculation of the total iron grade and recovery, and optimisation of iron ore beneficiation using hydrocyclones.

Jan 1, 2005

By Jian Yong Chen

The results of a laboratory investigation of pullout tests conducted on grouted, plain cable bolts are reported. The main purpose of the study is to determine experimentally the shear bond stiffiess of cement grouted and resin grouted cable bolt systems, which is an important input parameter for numerical modeling of cable bolt support. Three nominal embedment lengths of 152mm (6 inch), 203mm (8 inch) and 254mm (10 inch) were used and two types of grout namely cement and Anchortite resin were used. Two water- to-cement ratios of 0.3 and 0.4 were employed for the cement grout. The concepts of effective shear stress and effective shear stiffiess are explained and adopted to calculate the shear bond strength and the elastic shear bond stiffiess per unit length. A comparison of results with previous research is presented to reveal the effect of water-to-cement ratio and embedment length on the shear bond characteristics of grouted cable bolts.

Jan 1, 2005

Designing for early access to deep orebodies is an essential driver for improved project payback. Vertical shaft sinking techniques have been developed to allow concurrent mine level excavation while continuing to sink. Project cash flows can also be improved when simultaneously deepening existing shafts beneath operating hoisting systems. Further economic advantage has been realised through creative sinking sequencing in twin ventilation/service shaft projects. A fourth technique to reduce project schedules involves partial shaft barrel equipping allowing unrestricted access to construct stations and continue with level installations. This approach reduces interference with barrel sinking activities to insignificant proportions. This paper reviews how these approaches have added significant value to actual shaft sinking projects, as assessed from a contractorÆs perspective, and discusses some of the practical issues to be addressed when planning future projects. Designers need to take cognisance throughout all project engineering phases of the adage that you are only sinking when cleaning the face. Cleaning can only be sustained when there is sufficient hoisting capacity.

Jan 1, 2005

By V. Vorontsov

Catalysts Mo-Ni-S were prepared by combining MoS2 and NiS in weight ratios 1:1, 1:2, 1:4 and 2:1, each of which was admixed with 5%wt Ag and 5%wt YSZ to increase three-phase boundary surface area of the electrode. For comparison catalysts comprising Co-Mo-S in weight ratio of 1:1 of CoS to MoS2 admixed with 5%wt Ag and YSZ and pre-sulfided NiMoO4 were made. The catalysts were examined for electrochemical oxidation of hydrogen sulfide in solid oxide fuel cells (SOFC) at 850°C temperature. The catalyst prepared from 1:1 (wt. %) NiS:MoS2 demonstrated highest performance. Current density up to 1,330 mA/cm2 and power density up to 300 mW/cm2 were achieved using pure H25 gas, which are the highest among the reported H2S-powered fuel cells ever published in the literature. Anode materials of different NiS:MoS2 ratios have been characterized by means of X-ray diffraction (XRD), simultaneous TG/DSC analysis and Neutron Activation Analysis (NAA). TG/DSC and NAA results show that addition of NiS and Ag increases fuel cell performance due to improved structure/integrity of the anode. It has also been demonstrated that MoS2 is a suitable anode material in H2S-powered SOFC, with high activity towards H25 oxidation and thermally and chemically stable up to 850°C.

Jan 1, 2005