Search Documents

By Norihiko Fukatsu

In order to use effectively the previously reported new sensing system for hydrogen and oxygen potentials in molten copper, the criteria of the potentials for getting sound castings have been determined in the laboratory experiment. The copper melt equilibrated with a given hydrogen and an oxygen potential was rapidly quenched in the crucible. The relations between the holding potentials and the gas porosity in the solidified sample were investigated by measuring the density of the sample and microscopic observations. It was found that the defects of the gas porosity became the maximum at the potentials where the dissolved amount of hydrogen and oxygen was in the mole ratio 2:1. The samples having the density more than 99% of the theoretieal value were obtained in the higher oxygen and lower hydrogen potential region or in the lower oxygen and higher hydrogen potential region. The criteria thus determined were examined by comparing with the measured potentials in the practical casting machine. In tough-pitch copper casting, the problem due to gas porosity was found to be serious when the hydrogen potential increased. In the. oxygen-free copper casting, the evolution of hydrogen was found not avoided. The gas porosity in the casting, however, was found eliminated when the oxygen potential was kept at a low value.

Jan 1, 2003

By Stefan Mutz, Thomas Pretz, Jörg Julius, Frank Hilbk-Kortenbruck, Aachen, Hartmut Harbeck

"The annual global production of primary aluminium was about 22 million tons in the year 2000. This represents the second largest production rate in the world market after steel. Experts are predicting that the global demand for aluminium will rise in the near future.In contrast to other metals such as copper, the recycling of aluminium is considered relatively difficult. There are two main alloying groups, namely cast and wrought. In the case of aluminium it is important that the constituents within the scrap aluminium to be smelted are clearly identified. Within the secondary remelting process alloying does take place, but a removal of unwanted metal constituents is problematic. Therefore mixed aluminium scrap (not genuine in-house collected material) can only be used to produce cast aluminium. Thus, in other words a down-cycling of wrought (extrusions and rolled) products occurs. However, in spite of these difficulties there is an increasing trend to produce aluminium from secondary scrap (approx. 35% in Germany). Similar trends have been identified in the USA and other industrialised countries. This development is mainly caused by the high energy consumption for the production of aluminium from bauxite. Producing aluminium from scrap is saving about 95 % of the energy in comparison to the processing of primary raw materials.An improvement in sorting technology is necessary to separate wrought and cast alloys of aluminium as the absolute amount of recovery from old scrap is higher than the demand for cast.This contribution presents some alternative methods, utilizing automatic picking technologies, which will be used to separate secondary aluminium in the future. During the recent years, some major progresses have been made in automatic picking technologies for different applications in the processing of primary and secondary materials.For the sorting of aluminium scrap a special additional sensor will be necessary. The best detection will ultimately be based on online elemental analysis of single particles. First investigations in the field of laser based systems for these applications have already been performed several years ago. One of the laser based techniques is the laserinduced breakdown spectrometry (LIBS)."

Jan 1, 2003

By M. J. Blattman

Upon completion of an underground mine design, the planning engineer is faced with a surprisingly complex problem, “What development and mining sequence should be implemented so as to maximize the return on investment?” The problem relates to the scheduling of development headings to access stope production areas in such a way that the most money is made as quickly as possible for as long as possible. The total dollar value of the stopes, the average grade, the total tonnage, nor even the profit margin do not accurately give an indication of the “proper” mining sequence on their own. This paper will outline a method being developed by the author that can create a sequence of events that maximizes the net present value (NPV) of a given development and production design using information already being generated during the design process.

Jan 1, 2003

By P. Wittke-Gatterman

ABSTRACT: A three dimensional constitutive law for swelling rock is presented. It can be applied to the osmotic swelling of mudstone as well as to the swelling of rocks containing anhydrite. It describes the development of time-dependent strains and stresses due to swelling considering elastic and viskoplastic behaviour. Furthermore an anisotropic swelling behaviour can be considered. This constitutive model was implemented within a numerical computation program according to the finite element method and calibrated on the basis of the results of measurements in the investigation drift of the Freudenstein tunnel which is completely located in the unleached Gypsum Keuper. A parameter combination could be found which results in a good agreement between numerical solutions and results of measurements. Therewith an analysis procedure which enables the design of tunnels in swelling rock is available. ZUSAMMENFASSUNG: Im vorliegenden Beitrag wird ein dreidimensionales Quellgesetz vorgestellt, das nach derzeitigem Kenntnisstand sowohl auf das osmotische Quellen von Tonsteinen als auch auf das Quellen anhydrithaltiger Ton- beziehungsweise Schluffsteine anwendbar ist. Das Stoffgesetz wurde in ein Finite-Elemente-Programm implementiert und anhand von Meßergebnissen des im unausgelaugten Gipskeuper liegenden Untersuchungsstollens des Freudensteintunnels kalibriert. Es ist gelungen, eine Kennwertkombination zu finden, mit der alle Meßergebnisse gut beschrieben werden können. Damit steht ein Bemessungsverfahren für Tunnel in quellfähigem Gebirge zur Verfügung. RÉSUMÉ: Dans l'article présent un loi de gonflement à trois dimensions est présenté, qui peut être appliqué aussi bien au gonflement osmotique de l'argile compactée q'au gonflement de l'argile compactée ou du limon compacté contenant de l'anhydrite. Le loi de comportement était implémenté dans un programme numérique d'éléments finis et calibré avec des résultats de mesures de la galerie de recherche du tunnel de Freudenstein, situé dans le Keuper de gypse non lessivé. On est réussi à trouver une combinaison de paramètres avec laquelle tous les résultats de mesures peuvent être bien décrits. Par ce moyen, une méthode de dimensionnement existe pour des tunnels dans de la roche capable de gonfler.

Jan 1, 2003

By Stacy Loizeaux

The Beirut Hilton Hotel, which was built in 1975, but never occupied, was imploded on Sunday, July 14, 2002 by Controlled Demolition, Inc. (CDI) of Phoenix, Maryland and their client, Optimal Engineering Consulting & Contracting, SARL, (OECC) of Antelias, Lebanon to make room for a new hotel. Twenty-seven years ago, just days before the grand opening, the Hilton Hotel became the site of fighting in Lebanon’s Civil War. Christian and Muslim militiamen fought room to room for control of the building and other nearby hotels. The Hilton, two other major hotels and other high-rise buildings were ravaged by the fighting. The building was one of the three major hotels badly damaged, but not rebuilt, in Lebanon. Located in the City Center, the Hilton stood out in a major redevelopment area which, in recent years, had erased the scars of the 15 year long Civil Wa r.

Jan 1, 2003

By I. E. A. Aghachi

During static strain-aging of low carbon steel, when the material is pre-strained, the dislocation density increases. If totally or partially unloaded and aged for a prescribed time, interstitial solute atoms diffuse under the influence of the dislocation stress fields, thus tending to lock dislocations causing an increase in yield stress. If held for long periods at certain aging temperature, a decrease in yield stress (over-aging) is observed following the initial increase. This behaviour has been variously attributed to either recovery of cold worked dislocation structure and/or formation and coarsening of carbide precipitates. The present work demonstrates that, using a "process control" model for the competing processes of hardening and softening, dislocation recovery is responsible for over-aging of mild steel specimens under conditions tested during this investigation. Keywords: Strain-aging, Precipitation, Recovery

Jan 1, 2003

By A. Foscolos

Land reclamation and rehabilitation of depleted coal mines in the wider area of Ptolemais-Amynteon is practiced by the Division of Mines of the Public Power Corporation of Greece in order to conform to the concept of environmentally sustainable economic development of its operations. Detailed chemical and mineralogical studies were performed on reclaimed soils and their crops in order to evaluate the results of land reclamation and rehabilitation while similar studies were undertaken in adjacent, regularly cultivated, soils. Results indicate that trace element concentrations as well as concentrations of elements of environmental concern to be higher in regularly cultivated soils than the reclaimed ones. However, the concentration of the elements in wheat grains harvested from both, regular and reclaimed, group of soils is the same. The reason for this behavior is the very low water solubility, of the elements in the soils, due to their high pH values and the nature of their occurrence. As a result, wheat crops produced from reclaimed-rehabilitated soils developed on depleted lignite mines in the wider area of Ptolemais-Amynteon do not pose any health problem on either humans or animals when consumed.

Jan 1, 2003

By Gretel Parker

In situ Raman spectroscopic investigations of copper iron sulfides in leach solutions have been undertaken. Coupling potentiodynamic techniques to Raman spectroscopy produces a powerful tool for studying mineral surface response to changing conditions, while ESEM and high-vacuum techniques provide complementary ex-situ information on surface structure and composition. Oxidative acid leaching of chalcopyrite at ambient temperature yielded a product with S-S bonds that were shifted from those seen with covellite, with little evidence of elemental sulfur formation. Leaching of chalcopyrite led to non-homogeneous product distribution. Raman spectroscopy was able to identify the products formed on the mineral surfacein situ while leaching was occurring. Raman mapping and imaging demonstrated a surface distribution of the products which can be related to composition and structure changes of the mineral surface. The surface formed on chalcopyrite after anodic oxidation at 0.570 V vs. Ag/AgCl in 0.1 mol dm-3 HCl undergoes laser-induced transformation.

Jan 1, 2003

By Roberto Parra

The operational control in a Flash Smelting Furnace is based on the mass and energy balance of the chemical and mineralogical composition of the concentrates. It is well known that many troubles in the dust formation and slag quality occur without a clear correlation to a specific process parameter such as the matte grade or heat balance. This paper outlines two new considerations that could both help improve the entire quality of the process: blend characterization and versatile slag composition control. Related to the blend control, laboratory scale study has shown that the magnetite and dust formation don't have a linear behavior with the weight proportion of the blend and some optimal blends of2 or 3 types of concentrates can be identified. Related to the control of stag composition, the quantification of the slag liquidus temperatures and viscosity could be an effective operational tool for both for ferrite and fayalite slag that can also directly help deciding the blending parameters. From these viewpoints the benefits of the combination of these two approaches for high temperature operation is discussed. Keywords: Optimization, Copper concentrates, Flash combustion, Blends, Slag composition

Jan 1, 2003

By H. Deveci

Bioleaching/biooxidation is essentially a dissolution process with the involvement of acidophilic bacteria acting as the "catalyst" to accelerate the dissolution of metals from sulfide minerals. The contribution of bacteria to the metal dissolution is closely controlled by the growth of bacteria, which is itself affected by the physico-chemical conditions within the bioleaching environment. There are a number of operating parameters controlling bioleaching processes, which are required to be maintained within a certain range in the leaching environment whereby the activity of bacteria with the resultant oxidation of sulfide minerals can be optimized. In this regard temperature, acidity, oxidizing conditions, availability of nutrients, oxygen and carbon dioxide, surface area and presence of toxic ions are of prime importance for control and optimization of bioleaching of sulfide ores/concentrates. Bioleaching processes are temperature and pH dependent with optimum metal dissolution occurring in a particular range where the bacterial strain is most active e.g. mesophiles at 35-40°C and pH 1.6-2.0. Provision of nutrient salts is required to maintain the optimnm growth and hence metal dissolution with the quantity of nutrients apparently being dependent on the availability of substrate i.e. head grade/pulp density of an ore/concentrate. Oxygen transfer is one of the most critical factors since the oxygen levels below 1-2 mgll may adversely affect the oxidizing activity of bacteria. Bioleaching rate tends to improve with increasing the surface area at low pulp densities but, in practice. the pulp density is limited to -20010 w/v. Increasing concentrations of ions such as cr may also adversely affect the oxidative activity of bacteria. Keywords: Bioleaching, Biooxidation, Acidophilic bacteria

Jan 1, 2003

By A. R. Zambrano

Equations for power draft, capacity and work input for predicting the performance of industrial grinding mills are derived based on torque measurements using a laboratory instrumented mill. These derivations are based on mechanical principles and on the first-order kinetics of the grinding process. Rittinger's, Kick's and Bond's laws express work input as work index (Wi) times a particle size function. It is proposed that these laws are only particular cases of more general expressions having the particle size function raised to an exponent, i.e., the work exponent (We). Case studies illustrate the excellent prediction of the Wi - We models compared to the three mentioned laws, and, from the data, the corresponding general mill-sizing equation is derived. Key words: Grinding mills, Comminution, Work index, Mill sizing

Jan 1, 2003

By Victor A. Sowa

"Abstract - In 1938, a body of goethite and hematite was discovered beneath Steep Rock Lake near Atikokan, northwestern Ontario. This was at the time the largest and richest undeveloped iron ore body in North America. Mining began in 1944, fast-tracked by the needs of World War II, and through 1979 produced 79 Mt of 56.5% Fe. Production required the diversion of the Seine River, draining of Steep Rock Lake, building of a railroad, and a 25-fold increase of the local population. The mining project, at the time, was the largest project of its type undertaken in Canada. The current concepts of sustainable mine development and mine closures have advanced considerably since the period of operation and closure of the Steep Rock mines, and those operations would probably not have met current expectations of sustainability. However, some of the post-closure aspects of the mines provide illustrations of components of sustainability, which could form part of a basis for a post-mining sustainable land use plan. It is concluded that some of these components were successful in meeting current expectations of sustainable use, and although some aspects are unique to the circumstances at the Steep Rock mines, others could be applicable at other mine sites."

Jan 1, 2003

By Arthur E. Morris

Fifty years ago when Professor Yazawa began his career, the field of process simulation and modeling was in its infancy. Since then, tremendous progress has been made in our ability to model metal production flowsheets from mine to refined metal. This progress has come about by parallel developments in basic understanding of process chemistry and in computational techniques. This paper will review the progress made in process understanding and modeling in lead, zinc, and copper metallurgy from its inception to the present, and the role of Professor Yazawa's work in furthering this progress. Specific examples wi1\ be given for the sintering of lead concentrates, slag fuming, zinc concentrate roasting, flash smelting of copper, and pyro-extraction of zinc. Factors limiting further progress will be described.

Jan 1, 2003

By P. J. Suardini, T. E. Seppanen, M. J. Hanninen

In order to reduce the heat loading in the Tilden Mine kilns caused by burning coal, which in turn resulted in rapid and significant build-upon the kiln lining, internal carbon was added to the green ball prior to balling. Intensive laboratory testing led to three short-term full-scale plant tests that were successfully conducted. Appropriate environmental permits were obtained to allow Tilden to use internal carbon on a continuous basis. Findings concerning carbon addition rates, reductions in coal use, build-up reductions, fired pellet quality, and environmental issues will be discussed.

Jan 1, 2003

By John O. Marsden

In early 1998, Phelps Dodge embarked upon a program to investigate alternative technology for the extraction and recovery of copper, and other metal values, from copper concentrates. A review of all of the available process alternatives indicated that many were unsuitable for large-scale commercial application and others were clearly targeted at niche applications where contaminants (and consequently smelter penalties) were driving the decision-making. The result of this development program is the world?s first commercial application of high temperature pressure leaching of chalcopyrite concentrate at Bagdad, Arizona, which was commissioned in the second quarter of 2003. Other related processes are in various stages of development. In addition to the obvious considerations, the economic aspects of this technology have been considered in detail at each step in the development of the program. The technology developments in this area are reviewed with emphasis on the economic viability and commercial application.

Jan 1, 2003

By N Elith

Coal is a valuable energy source in New Zealand and has been mined from the West Coast for over 100 years. Stockton Mine is New Zealand's largest opencast coal producer supplying around 1.5 Mt of hard coking and thermal coal to international markets annually. The Stockton Plateau forms an extensive, gently inclined dip slope on erosion resistant Lower Eocene Brunner Coal Measures unconformably overlying basement rocks. The dip slope rises 600 - 1000 masl, locally dissected by fault scarps and present-day fluvial systems, some of which are deeply incised. Within the Mt Augustus Mining Block overburden comprises of a 30 - 40 m thick sequence of fluviatile, coarse to granular coal measure sandstones. High quality coking coal is preserved as a gently dipping, 10 - 12 m thick seam. High and sometimes very steep cliffs of jointed overburden shape the skyline escarpment, above steep forested slopes and gullies. As mining has progressed at Mt Augustus individual coal blocks are progressively becoming more technically challenging. This paper outlines the scientific approach taken by Solid Energy International and mining contractors to carefully unlock many thousands of tons of coal whilst protecting nearby flora and fauna from the impacts of dislodged rock and other blasting side-effects. The strategy involved: an expert-driven onsite risk assessment,formulation of a management plan to manage impacts,conducting an in situ vibration research program, andanalysis of results and operational designs to eliminate potential environmental problems.

Jan 1, 2003

By G A. Streltsova

In the paper the main concept of qualitative simulation is determined when computer-aided designing and forecasting of designs of robotised continuous-flow working face complexes for underground mining of hard ores. The parametric model æunderground ore mineÆ and its components û composite models are considered. Frame description of structure of working face complex and methods of organising of rule-oriented representation of knowledge when itÆs operating are given. The architecture of the developed prototype of expert system æworking face complexÆ and construction of a knowledge base for it are described when solving problems of multi-criteria optimisation of computational parameters of the working face complex under conditions of uncertainty. The guidelines for further development of knowledge base and expert system are given.

Jan 1, 2003

By R. W. Smith, K. A. Altman

The use of activated alumina for the removal of selenium from heap leach detoxification solutions was studied at a laboratory scale. Three different aluminas were studied, one unmodified and two chemically modified to function better in a basic pH range. The best performer, Discovery Chemicals DD-6, readily accumulated selenium oxyanions. Furthermore, it could be stripped of selenium and several metals by a mild caustic solution (pH 11.5 – 12.0) and regenerated for further use. Tests using - 600 µm, + 300 µm (28 x 48 mesh) material indicated that 96 % could be removed from solution and using – 1.18mm, + 600 µm (14 x 28 mesh) material 91 % could be removed. However, soluble silica can accumulate on the activated alumina and subsequently interfere with its regeneration and should be removed from the detox solution prior to use of the adsorbent.

Jan 1, 2003

By Charles Washburn

The authors review mercury sources, and contaminant streams, with particular emphasis on mercury that is extracted from precious metal ores. The design and operation of both large and small mercury distillation facilities are detailed. The relevant properties and characteristics of mercury and mercury vapor are presented. Facility engineering with respect to industrial hygiene, area ventilation, and material handling is presented.

Jan 1, 2003

By Chu Yong Cheng

The solvent extraction (SX) processes of the three pressure acid leach (PAL) nickel plants in Western Australia have been reviewed. The use of intermediate precipitation, solids/liquid separation and re-leach in the three W A nickel plants make these processes complicated and costly in capital and ?operation. The research work carried out by the SX group at the AJ Parker Cooperative Research Centre for Hydrometallurgy I CSIRO Minerals has led to the development of direct solvent extraction (DSX) processes to recover and purify nickel and cobalt from leach solutions. The simplicity of the process flowsheets and the expected savings in capital and operating costs are the major advantages of the new DSX processes over the reviewed processes. By using a new synergistic organic system in semi-continuous tests with a pilot plant leach solution (after iron precipitation) from BHP-BiIliton Stainless Steel Materials, the metal values (Ni and Co) together with zinc and copper were separated from the major impurities (Mn, Mg and Ca, together with Cl) in the first SX circuit. The co-extracted manganese, magnesium and' calcium were easily scrubbed out. After stripping, the metal values (Ni and Co) together with zinc and copper were concentrated, resulting in a much smaller second SX circuit and equipment in the down stream processes. The extraction and stripping kinetics of the metals with the new synergistic organic solution were very fast. The extraction and stripping almost reached steady state within 0.5 minutes. Semi-continuous test work with a synthetic leach solution, a cobalt pilot plant leach solution from Peko Rehabilitation Project Pty Ltd and a synthetic solution to simulate a concentrated laterite leach solution from BHP-Billiton Stainless Steel Materials showed that manganese, calcium, copper and zinc can be effectively and efficiently separated from nickel, cobalt and magnesium by extraction, scrubbing and stripping. This led to the development of another DSX process using D2EHPA to recover nickel and cobalt from leach solutions.

Jan 1, 2003