Search Documents

By A. McLean, W. Q. Chen, W. Yan, M. Barati, Y. D. Yang

In order to maximally remove the harmful impurities phosphorus and reduce the loss of valuable elements from Si-based alloy for production of solar-grade silicon, thermodynamic properties of the Si-based alloy were studied. In this work a new model, the Molecular Interaction Volume Model (MIVM) derived from statistical thermodynamics, was successfully used in the Si-based and Si-Fe-based alloy. The calculation started from binary Si-Fe, Si-P and Fe-P systems, then the thermodynamic parameters of ternary systems could be derived based sub-binary systems. Using the activity coefficients of the elements in the Si-based alloys and the saturated vapor pressure of the pure substance of the components, mass fraction of P during vapor-liquid equilibrium can be calculated. The calculated thermodynamic parameters were compared with experimental data available in different publications, and it is found that the thermodynamic parameters calculated using MIVM model are in good agreement with the measured results. The calculated result shows that the mass fraction of phosphorus during vapor-liquid equilibrium of Si-Fe-P melt increases with the increasing phosphorus content and decreasing temperature. This is an important direction for experimental practice in vacuum or low-pressure EML refining of ferrosilicon for potential production of solar-grade silicon without significant vaporization loss of valuable element.

Jan 1, 2015

By P. Schumacher, M. Fein

"INTRODUCTION Newmont’s Twin Creeks operation, part of its Nevada operations, produces gold from two large open pit mines. Mined ore is processed at one of three on-site facilities: a refractory mill with two autoclaves, an oxide mill and heap leaching facilities. Twin Creeks also processes various off-site sourced concentrates and ore including high grade underground ore from the Turquoise Ridge joint venture with Barrick Gold Corporation. This paper discusses Twin Creeks’ strategic mine planning process which is part of an in-depth continuous improvement program called “Full Potential.” The process involves cost analysis, phase design validations, life-of-mine production scheduling optimization, mill blending strategy and stockpile management. Through this Full Potential strategic planning, Twin Creeks is creating significant value by increasing near term free cash flow and life of mine net present value (“NPV”) and achieving cost reductions. TWIN CREEKS OPERATION Twin Creeks is one of the major gold producers in Newmont’s Nevada operations (see Figure 1, 2 and 3). Located approximately 15 miles north of Golconda, Twin Creeks produced approximately 28 % of the Nevada operation’s 2013 gold production of 1.8 million ounces (Newmont 2014). The production included Turquoise Ridge sourced gold ore from the joint venture (75% Barrick Gold Corporation, 25% Newmont).At Twin Creeks, there are two large open pits, named Mega Pit and Vista Pit (see Figure 4, 5 and 6). There are 3 to 5 phases in Mega Pit and 2 to 5 phases in Vista Pit depending on the gold price assumption. There is also an underground exploration project at the bottom of the Vista Pit. Twin Creeks produces gold from a variety of ore types requiring different processing techniques depending on economic and metallurgical characteristics. To ensure the best use of processing assets, engineering and processing groups at Twin Creeks utilize a Mixed Integer Linear Programming (“MILP”) model to guide the flow of mine sequences and material routing to various process facilities (Kawahata, Schumacher and Hufford 2013)."

Jan 1, 2015

By C. Díaz, M. Barati

Prof. Torstein Utigard's untimely death, in the spring of 2012, put an abrupt end to a meritorious career in the field of high temperature chemical process metallurgy. As an academic in the Department of Materials Science and Engineering of the University of Toronto, Torstein made solid contributions to the advancement of knowledge pertaining to production and refining of both nonferrous and light metals, and to the development of inquisitive and innovative young people in extractive metallurgy. In this profile, the authors highlight aspects of Torstein's rich personality and of his contributions to his field of expertise.

Jan 1, 2015

By J. L. Ellenberger, G. S. Esterhuizen, T. Miller, M. M. Murphy

A limestone mine in Ohio has had roof instability problems that have led to massive roof falls extending to the surface. This paper describes a collaborative study of these events undertaken by the National Institute for Occupational Safety and Health and the mine owners. The study focuses on the roles that weak, moisture-sensitive floor and weak bands in pillars play in a general instability that led to roof falls at this mine. The NIOSH Stone Mine Pillar Design software (S-Pillar) does not include analysis for weak floor or weak bands and recommends that when such issues arise they should be investigated further using a more advanced analysis. It is important to recognize that without the impact of the floor or weak bands, the calculated inherent stability factor for these pillars is within the recommended design range. Therefore, to further investigate the observed instability occurring on a large scale at the Ohio mine, FLAC3D numerical models were employed to help determine the failure mechanism. Roof-to-floor convergence monitors were also installed in the areas predicted to have further instability. This case study will provide important information to limestone mine operators regarding the impact of weak floor causing the potential for roof collapse, pillar failure, and subsequent subsidence of the ground surface. This recent case demonstrates that weak floor can be a significant factor in pillar stability and should be assessed during the design stage of the mine.

Jan 1, 2015

By S. A. Smith-Hamm, E. A. Sarver, A. S. Cox

Appalachia is an increasing concern, as unnaturally high TDS and/or associated specific conductivity (SC) may contribute to deteriorated stream ecosystem health. The aim of this preliminary study was to explore the efficacy of accelerated leaching as a means of minimizing long-term TDS/SC generation by problematic overburden materials. Five spoil samples were collected and leached using simulated rainwater solutions under ambient and acidified pH conditions. SC and pH were monitored during each leach cycle, and inductively coupled plasma-mass spectroscopy (ICP-MS) was used to determine how leaching conditions affected the release of specific ions. This paper highlights the results of both jar and column leaching tests. Among the most significant findings was that for certain spoil materials, the SC in the leach column effluent was effectively reduced when the spoil was first leached with acidic rainwater followed by ambient rainwater, as opposed to leaching with ambient rainwater alone. This suggests that accelerated leaching might aid in the long-term stabilization of some materials.

Jan 1, 2015

By R. V. Ramani, K. V. Raj, S. Bandopadhyay

The air flow problems in openpit mines are complex. Computational fluid dynamics (CFD) models can provide detailed information regarding air flow pattern, velocity distribution, temperature, and pollutant concentration in an enclosed domain of an openpit mine. A range of turbulent models can be selected with varying complexity and accuracy. Pollutant transport models, however, differ in their assumptions and structure as well as in the algorithms they use. As a result, predictions vary from model to model. This paper presents a study of pollutant transport in an actual openpit mine under a stable boundary layer. The objective was to test two turbulence models using similar geometry and the same input conditions and model constants. Measured data were used to compare the results of the two CFD models, namely, the kappa-epsilon (к-є) model and the Large Eddy Simulation model. Despite the complex synoptic situations, different meteorological input data and fast-changing conditions, the simulation results from both the models were in good agreement regarding the dispersion of pollutants.

Jan 1, 2015

By Chee S. Theng

As the 2015 president of the Society for Mining, Metallurgy & Exploration Inc., I am pleased to present the 2015 issue of the Transactions of the Society for Mining, Metallurgy & Exploration Inc., Vol. 338. A significant portion of the contribution that we make as a professional society is the publication of professional and technical papers that accelerate the advancement of scientific knowledge and enable the transfer of technology. Communication within the mining community is the key to a successful society. This technology exchange continues a tradition that dates back to the 1871 meeting of 22 mining engineers in Wilkes-Barre, PA, that resulted in the founding of AIME. Those individuals envisioned that these transaction volumes “would form a most valuable and greatly needed addition to our professional literature.” This volume fulfills that pledge. The 2015 Transactions contains some of the most interesting research and insights from the past year and features an international slate of authors spanning industry, academia and government. Papers include the latest findings from the U.S. National Institute for Occupational Safety and Health (NIOSH) and special-focus articles on gold processing, iron ore processing and coal processing. The 2015 Transactions consists of a total of 67 technical papers, encompassing all 22 papers published in 2015 in the Technical Papers Section of Mining Engineering (Vol. 67) and all 29 papers published in 2015 in Minerals & Metallurgical Processing (Vol. 32). Additionally, this volume contains 15 papers and one discussion that are being published for the first time in this issue. The papers presented in this volume were written by some of the most distinguished professionals in the industry worldwide. All of the technical papers were peer-reviewed. The process of review and publication requires much hard work by authors, reviewers and our publications staff. As the 2015 president of SME and on behalf of all our members, I would like to extend our gratitude to all whose volunteer efforts contributed to the publication of this volume.

Jan 1, 2015

By F. Calizaya, M. G. Nelson

This paper presents a summary of basic requirements for the design, installation and operation of booster fans in coal mines, especially in deep and/or extensive mines. It includes a brief description of the major steps that should be followed to ensure that these units are used in coal mines safely and efficiently. The guidelines were prepared based on the standards and regulations adopted by two prominent coal mining countries, the best practices developed by the mining industry, and the applicable standards used in the United States for the fail-safe operation of main fans.

Jan 1, 2015

By R. Halatchev

This paper treats the spatial aspect of mine sequence optimization, revealing it in the context of determining the optimum number of cutbacks of an openpit mine. Cutback mining is currently a dominant method in the mining of base and precious metals. It is based on a pseudo-economic discretization of the pit space using advanced pit design algorithms. The result of implementing such an approach of pit design is the generation of pit shells, which need to be grouped into an optimum number of cutbacks to maximize project value. In this paper, the development of a mathematical solution of this problem using combinatorial analysis is presented. The solution provides a multivariate investigation of the optimum mine sequence with the implementation of a method for production scheduling optimization that uses Net Present Value (NPV) as a criterion for assessing the economic efficiency of mine sequencing. A case study using the conditions of a hypothetical openpit gold mine is provided to illustrate the applicability of the approach. The results obtained reveal the complex nature of NPV variation as a function of the cutback geometry.

Jan 1, 2015

By Rajarshi Pramanik, Nirjhar Dhang, Dilip K. Baidya

"This paper performs the reliability evaluation of pile foundation under vertical loading condition using the concept of fuzzy set theory. The uncertain parameters are expressed as fuzzy numbers. Monte Carlo simulation technique in conjunction with fuzzy set theory and fuzzy reliability index approach are implemented in evaluation of the probability of failure of pile foundations. The results are validated through some well established methods such as, First Order Reliability Method (FORM), Second Order Reliability Method (SORM), and direct Monte Carlo Simulation (MCS). Response surface method (RSM) is used to approximate the original limit state equation through second order polynomial. The effect of the position of the water table is also highlighted. Finally, the effect of the variation of applied load is examined and it is observed that the fuzzy reliability analysis gives more conservative estimate of failure probability than the other methods.INTRODUCTIONCivil engineering structures, such as high rise buildings, bridges, offshore platforms etc. are always subjected to vertical as well as horizontal loads. To support these structures, pile foundations are generally the solution in most of the situation. It transmits load from the superstructure to soil at a reasonably great depth. This transfer may be by vertical distribution of the load along the pile shaft or a direct application of load to a lower stratum through the pile tip. Different methods are available to estimate the capacity of piles embedded in different types of soil and under the application of vertical and horizontal loading. To consider the variability in soil and other unforeseen able situation, generally a reasonable value of factor of safety is used to estimate the designed capacity of the pile. Recent developments have shown a trend to place the treatment of uncertainty on a more formal basis, in particular by applying the results of reliability theory to geotechnical engineering. Keeping in mind the importance of pile foundation in the engineering structures it is essential to maintain a high structural safety which result in increase in reliability. The probability theory has been proved to be a powerful tool for representing variability in mathematical models. The variability associated with soil parameters and the modeling uncertainties are needed to be considered for the reliability assessment purpose.Recent development (Zhang et al. 2005; Misra and Roberts 2006; Haldar and Babu 2008; Basu and Salgado 2012; Teixeira et al. 2012; Pula and Rozanski 2012; and Chan and Low 2012) showed that the reliability analysis of pile foundations subjected to axial as well as lateral load has been one of the important current research topic in geotechnical field. Probabilistic based performance criteria were quantified for a single pile and pile groups in cohesionless soil by Eloseily et al. (2002). A p-multiplier approach was incorporated into the analysis to modify the p-y curve for a single pile to obtain the p-y curve for individual piles in a pile group. A statistical analysis of set up capacity of pile was carried out from the database of a large number of pile testing data in clay by Yang and Liang (2006). Load and resistance factor design (LRFD) using FORM was used for examining the different load and resistance factor for different target reliability index. Limit state analysis of drilled shaft was performed by Misra and Roberts (2006) in probabilistic framework. The fuzzy based reliability analysis (Dodagoudar and Venkatachalam 2000; and Park et al. 2012) of the earth slope was reported in the literature. Dodagoudar and Venkatachalam (2000) presented a new approach, called fuzzy point estimate method (FPEM) for reliability evaluation of earth slope. Park et al. (2012) reported a hybrid approach, fuzzy set theory in conjunction with Monte Carlo simulation technique, to determine the failure probability of earth slope. Second Order Reliability Method"

Jan 1, 2015

By K Ilamparuthi, R. K. Madhumathi

"This paper presents the results of 1g model tests conducted on model piles both single and two pile groups embedded in sand by physically inducing lateral soil movement. From the test results it was found that the pile with higher L/D ratio exhibits higher deflection in case of pile embedded in medium dense sand whereas in loose sand the response is vice versa with higher deflection for the pile of lesser L/D ratio. The induced bending moment in piles is more for longer piles than shorter piles irrespective of the density of sand bed. It is also found that the pile head deflection and the bending moment are found to decrease exponentially with increasing distance between the pile and the wall. For pile group arranged in a row parallel and perpendicular to retaining wall, the deflection of single pile is more than the deflection of two pile group irrespective of the depth of excavation for spacing of piles tested. The influence of soil movement on the lateral response of pile is also analyzed through 3-dimensional finite element analysis. The numerical results thus obtained are validated with the results of experiments. The Mohr-Coulomb material model adopted to represent the soil behaviour predicts the response of pile reasonably and compares well with the experimentally observed response.INTRODUCTIONPile foundations are adopted to support structures such as foundations of high rise buildings, transmission towers, offshore platforms, bridge abutments etc., when good bearing stratum is not present at shallow depth to bear the loads of these structures. In the recent past particularly in the urbanized areas structures are built close to one another and nearby excavation will cause a reduction of lateral earth pressure and soil movement behind the retaining wall (Ong, 2004). The reduction in support stress will induce additional movement to the pile and leading to distress in pile foundations located adjacent to supported excavation. In these situations understanding the response of piles next to supported excavations becomes essential.The behavior of piles subjected to soil movement was studied by Poulos and Chen (1996 and1997) through tests on 1g models and the findings concluded that the maximum bending moment was found to decrease with decreasing pile diameter and decreasing pile spacing . Leung et al. (2000 and 2003) studied the effects of excavation induced soil movement on pile foundations in sand through centrifuge tests and established that the restraints on the pile head would cause additional shear force and/or bending moment at the pile head, although the restraints help to reduce the pile head deflection/rotation. In the theoretical studies of Poulos & Chen (1997), boundary element method (PALLAS) was used for analysing the pile subjected to lateral soil movement and charts were proposed for designing the piles. Pan et al. (2002) and Miao et al. (2006) analysed the passive pile behavior through three dimensional finite element analyses. However research works reported on piles subjected to lateral soil movement are limited."

Jan 1, 2015

By S. P. Mukherjee, Smita Tung

"Piles are generally subjected to uplift in case of under ground and water front structures. Sometimes piles are also to resist uplift loads in transmission towers, dry rock, and so on. Experimental investigations of single piles and pile groups have been carried out using model hollow circular aluminum piles, having 25.4 mm outer diameter and lengths of 600 mm, 750 mm and 900 mm. Pile groups of 2?1 and 2?2 arrangements have been used in the experimental investigations. L/d ratio has been kept equal to 24, 30 and 36 in all the cases. All the single piles and pile groups have been tested under vertical uplift. Spacing between two piles in a group has been varied with respect to pile diameter such that spacing to diameter ratios of pile are 3, 4 and 5 in case of pile groups. An attempt has also been made to analyze those models of single piles and pile groups under vertical uplift by PLAXIS 3D software. Good analogy has been observed between the results of experimental and numerical studies. A parametric study has been carried out to observe the variation of ultimate uplift capacity of pile groups with spacing and depth of embedment. It is observed that for a particular embedment length of pile and a particular group arrangement the ultimate uplift capacity increases with increase of spacing. It is also investigated that for a particular spacing and particular group arrangement, the ultimate uplift capacity increases with increase of embedment depth. Those variations have also been presented with graphs which are generated considering non dimensional forms of parameters. The paper brings out change in pullout capacity of pile groups with spacing and embedment depth of piles.1. INTRODUCTIONPrediction of uplift capacity of single piles and especially of pile groups is one of the most interesting areas of research in geotechnical engineering. Pile foundations are frequently used to transmit the superstructure loads to deeper strata if the subsurface soil is of inadequate strength. The worst possible case may be considered to occur when all the piles in a group subjected to uplift. In cohesionless soils, the shaft resistance is an important source of pile capacity under axial loading, especially when the pile is subjected to uplift loading. Poulos and Davis (1980) recommended estimating the uplift capacity of piles as 2/3 of the downward shaft resistance. Later Ramasamy et al. (2004) indicated that the upward shaft resistance is significantly less than the downward shaft resistance. Some studies were conducted on the behavior of a single pile under uplift loads, such as those by Sowa (1970), Vesic (1970), Das and Seeley (1976), Levacher and Sieffert (1984), Rao and Venkatesh (1985), Chattopadhyay and Pise (1986), and Shanker et al. (2007). Das et al. (1976) conducted a model study to test the uplift capacity of single piles and pile groups buried in sand, and they also determined a relationship between the efficiency of a pile group and its spacing. Chattopadhyay and Pise (1986) proposed an analytical method for predicting the uplift capacity of piles embedded in sand and obtained reasonable agreement between experimental and theoretical results. Gaaver (2013) investigated experimentally that an upward displacement of about 1.4–2.5% of the pile diameter is required to attain the net uplift capacity for both single piles and pile groups. The uplift resistance of pile groups depends on the several variables like group size, shape, spacing to diameter ratio of piles, embedment depth to diameter ratio of piles, soil type and its density and soil-pile friction angle."

Jan 1, 2015

By José Carlos do Amaral, Marcelo Groszownik, Jorge Beim

"Initiated in 2008, the project of this 1800 km long Electrical Transmission Line is a job of extreme technical complexity, crossing regions of major forests and rivers. When ready, it will allow the large Brazilian states of Amazonas, Amapá and Pará to use the energy from hydroelectric plants, thus eliminating the need for the use of diesel fuel thermal plants, with their much larger environmental footprint. Due to its extraordinary characteristics, the Green Peace and the Discovery Channel constantly visited the job. The part between the Amazon and the Xingu rivers started in 2012, and encompassed about 100 transmission towers with up to 150 m height, through a region known as “Alagados”. This region exhibits a 1.5 m water level during the rainy season, and soaked ground the rest of the year. Navigation of regular vessels is impossible during the flood season, when a dense vegetation called “bulhado” fills the riverbed, and vehicle traffic is impossible during the dry season, due to the extremely low surface soil resistance. Great logistical and technical difficulties were encountered for driving and determining the capacity of the piles. New systems had to be developed for driving the piles, with the simultaneous use of 15 small piling rigs. The final penetration, total number of hammer blows during driving, plus Dynamic and Static Load Tests were used for determining the driving and acceptance criteria.The geographical challenge and initial conditionsThis paper describes the execution of foundations for a 500 kV Electrical Transmission Line in a region that becomes flooded during the rainy season and heavily muddy during the dry season. This is the monsoon climate, typical of the equatorial region of Brazil, where there is a rainy season lasting for about half the year, followed by a very dry season. The temperature varies very little throughout the year, due to the proximity to the equator. The locals call the rainy season “winter” and the dry season “summer”.The most important part of the so-called “Alagados” region is situated inside an Environmental Extractive Reserve (RESEX) called “Verde para Sempre” (Forever Green), created in 2003. This is one of the largest environmental reserves in Brazil. It is an area controlled by the Brazilian Environmental Control Department, the Chico Mendes Institute (ICMBio). The environment control parameters are very strict.No deep foundation had ever been executed before along the “Alagados” region. The main challenge faced on this job, however, was working in a place where self-propelling vessels or land vehicles and equipment cannot be used. During the rainy season there is a dense and intricate vegetation called “bulhado”, which prevents the movement of outboard motor boats with propellers going deeper than 50 cm. In the dry season, the heavy mud prevents the movement of foundation equipment, excavators, trucks and other machinery."

Jan 1, 2015

By Abolfazl Eslami, Sepide Lotfi, Mohammad M. Eslami

"Via direct CPT methods for pile capacity prediction, correlation coefficients smaller than unity are used to relate cone tip resistance (qc) and sleeve friction (fs) to pile toe capacity (rt) and shaft capacity (rs), respectively. For linking CPT data to pile capacity, factors such as diameter, penetration rate, partial embedment of pile toe into a hard layer, mechanism of plunging, failure zone, data processing, and stress-strain conditions must be considered. The aim of this paper is to investigate the role and significance of scale effects and establish direct relation between CPT data and pile shaft capacity. A database has been compiled including 40 full scale pile load tests and CPT sounding records for calibration and validation of the proposed approach. Analytical studies demonstrate that differences between pile and penetrometer penetration rate, geometry, and stress-strain conditions influence the relation between fs and rs. By considering the determinants, a procedure is proposed from which the pile shaft capacity can be predicted. This approach demonstrates better agreement with measured capacity by static loading test and less scatter than other current CPT methods.IntroductionAmong different approaches for pile capacity prediction, in-situ tests such as SPT and CPT have been used as supplementary of static analysis. Due to similarities between CPT and pile, the measured cone tip resistance and sleeve friction can be employed for prediction of unit toe and shaft capacities, respectively.Determination of pile capacity from CPT data includes two main approaches: direct and indirect methods. Direct CPT methods apply the measured values of cone tip resistance (qc) for pile toe capacity (rt), and sleeve friction (fs) for pile shaft capacity (rs) with some modifications regarding scale effects. Indirect CPT methods employ friction angle and undrained shear strength values that have been estimated from CPT data.When using direct CPT methods to relate qc and fs to rt and rs, correlation coefficients smaller than unity are used. Factors such as diameter, penetration rate, mechanism of plunging, failure zone, data processing, and stress-strain conditions must be considered for correlation between CPT and pile capacity. The work presented in this paper aims toward ameliorating the situation in the area of pile shaft capacity prediction, based on cone sleeve friction.Case histories from full-scale tests are compiled and analyzed by means of six methods including five direct CPT methods for shaft capacity prediction and the proposed method."

Jan 1, 2015

By Sanjay Gupta, Sorabh Gupta, Ravi Sundaram, Abraham Varghese

"Geotechnical investigation for the Kochi Metro revealed a critical section of the Viaduct near Ernakulam Junction Railway Station. Four piers, located over a 220 m stretch, were passing through an area with substantial thickness of soft clay. The scope of the geotechnical investigation included two boreholes and a static cone penetration test at each pier location. In the boreholes, field vane shear test was conducted at different depths in addition to the routine SPT. The design of heavily loaded piles in such strata is a challenge due to the liquefaction of the shallow sands and negative skin friction / down-drag in the soft under-consolidated clay. Bored cast-in-situ piles of 1500 mm diameter extending to 50-60 m depth were used to carry 500-600 tonnes load.INTRODUCTIONThe first phase of the rapid transit system at Kochi, Kerala (See Fig. 1) whose elevated route spans from Aluva to Thripunithura covers a total distance of about 25 kilometers. One of the more critical sections of the viaduct exists near the Ernakulam Junction Railway station where the alignment takes a sharp curve to move towards Vyttila, crossing the railway tracks and running partially over the approach of South over-bridge.In this section, four piers located on either side of the railway tracks near the Route Relay Cabin of Ernakulam Junction Railway Station pass through an area with substantial thickness of soft underconsolidated clay.The alignment is geotechincally challenging due to the presence of loose liquefiable sand and soft underconsolidated and sensitive clay.Initial investigations by the owner based on limited boreholes only yielded conservative and inconclusive pile capacities. For a thorough understanding of the soil behaviour, a detailed geotechnical investigation was carried out to assess the engineering behaviour of the soil strata.The scope of the geotechnical investigation included two boreholes and a static cone penetration test at each pier location. In the boreholes, field vane shear tests were conducted at different depths in addition to the routine SPT."

Jan 1, 2015

By Rick Piovesan, Pramod Rao, Nihal Bohra, Mark Wahler

"This paper discusses the approach followed for the geotechnical design of 355 mm and 457 mm diameter driven open-ended steel pipe piles used for a gas plant at a green field site in Pilbara region in Australia. The principal bearing layer at the site comprises of calcareous Red Bed soils and weak rock, which is the typical geology along a significant length of the northern Western Australian coastline with carbonate content up to 70%. The uncertainty associated with the mechanical behavior of the calcareous soils and cemented soils (weak rocks) presented design challenges in the selection of appropriate pile design method and design parameters for pile capacity estimation during Front End Engineering Design (FEED). The American Petroleum Institute (API)-based design methodology was adopted. The representative design parameters for the Red Bed weak rock were established by treating the weak rock as clay with undrained shear strength as one-half of the characteristic unconfined compressive strength (UCS) value. Both statically load tested and CAPWAP (Case Pile Analysis Wave Program) estimated ultimate axial pile capacities on 25 early pre-production indicator piles demonstrated that the API design methodology for siliceous soils provides reasonable prediction of axial pile capacity in the red bed soils/weak rock and no reduction to API computed axial capacity due to carbonate content is warranted. The results also demonstrated that penalizing axial pile capacity solely based on carbonate content is not appropriate.IntroductionA gas processing facility was proposed to commercialize the gas reserves located 130 km offshore from the north-west coast of Western Australia (WA). The project site is a green field site located in the Pilbara region along the northwest coast of WA. Specific information regarding the site has been withheld due to confidentiality reasons. The site layout is shown in Figure 1.The site comprises low-lying tidal flats, clay pans and sand dunes covered with low scrub. The onshore site levels vary from elevation 1 m to 10 m AHD (Australian Height Datum), with the largest proportion of the area (excluding sand dunes) between elevations of 1 m and 3 m.The onshore facilities are to comprise a liquefied natural gas (LNG) plant site, a construction camp, the land-based portion of the materials offloading facility (MOF), roadways, and borrow pit areas.The existing ground levels within the process train area, where pile load testing was performed, vary from over 7 m AHD where the summits and peaks of the central dune exist to typically 1 m to 2 m AHD towards the east and west edges of the dune. The proposed finished grade for the process train is set at 7 m AHD."

Jan 1, 2015

By João Veludo, Eduardo Júlio, Helen D. Robinson, Jesús E. Gómez

"Utilization of micropiles for structural retrofit requires connection of the micropiles to the footings of the existing structure. Almost ten years ago, an experimental research effort was carried out in the US to investigate the magnitude and mechanism of development of the bond strength between micropiles and existing concrete. The study resulted in important conclusions on the mechanism of connection capacity development and provided specific recommendations for practical design of micropile-to-footing connections. In the last five years, the original study was complemented by an intensive experimental effort in Portugal aimed at answering many of the questions still remaining on this topic. This paper is a summary of the knowledge that is presently available on the capacity of micropile-to-existing footing connections. It presents the results and observations of model tests performed in the US and Portugal, as well as some tests from actual construction sites. The paper presents clear evidence that friction may be the most important component of connection capacity. It also presents a clear correlation between confinement and connection capacity.IntroductionUtilization of micropiles for structural retrofit requires connection of the micropiles to the footings of the existing structure. This is often accomplished by drilling through the footing and developing the connection by direct bond between the micropile grout and the existing concrete. Almost ten years ago, an experimental research effort was carried out in the US to investigate the magnitude and mechanism of development of the bond strength between micropiles and existing concrete. Smooth and textured micropile inserts of varying lengths were tested to failure inside pre-drilled holes of varying diameters. That investigation led to several publications (Gomez et al. 2005, Wilder et al. 2005, Cadden 2009) on the mechanism of development of bond strength between micropiles and concrete, which included a chart for preliminary bond value selection depending on the diameter of the hole and texture of the micropile.An intensive testing program was carried out in Portugal in the last five years. The program focused on answering questions posed by the original investigation and on finding the relationship between connection capacity and level of confinement. Both investigations, and especially the testing performed in Portugal, provided an invaluable amount of information on the mechanisms of failure of micropile-to-footing connections. This information should be the basis for development of design procedures that, until now, were not available."

Jan 1, 2015

By Daniel W. Mageau, Larry W. Applegate, Aaron K. McCain

"An innovative method of ground freezing was successfully tested to create a “dry” excavation condition for a new building foundation at a site in downtown, Miami, Florida. The subsurface conditions in Miami generally consist of very porous, weak limestone and sand with groundwater near the surface. Water flow through these materials can be very high. Dewatering is extremely restricted in Miami so deep below-grade structures are rare and expensive. A new, innovative method to allow deep excavations in dry conditions without dewatering involves the creation of a thick, temporary, frozen soil plug below the planned excavation depth across the entire site to cut off vertical groundwater flow during construction. Frozen soil is impermeable and very strong and has long been used for temporary structural and water-tight shored walls. Using the same proven principals, frozen soil plugs are very effective at cutting off water from the bottom of the excavation as well as resisting upward buoyant forces. This new freezing method can be used for fairly deep excavations in new building construction supported on deep foundations. The building piles act as temporary anchors for the frozen plug to resist very high upward buoyant pressures until the permanent structural slab is completed.IntroductionUnlike other Cities, below grade basements are rare in Miami. The few basement foundations constructed have utilized a cumbersome and expensive method of excavation and shoring involving underwater excavation, tremie slabs, and commercial divers. The key issue for underground construction in this area of the country is the vertical flow of groundwater through the base of the excavation. To deal with this issue in the past, the contractor first installed all of the building piles and the perimeter shoring walls. Then, interior sheet pile walls are installed to create small manageable excavation pits. Each pit is then excavated through standing water “in-the-blind” and around the buildings support piles. The final excavation, interior struts, and inspection is performed by commercial divers. Finally a thick foundation tremie slab is poured under water. This method could be successful but proved to be time consuming and expensive. In addition, some building piles were occasionally damaged during the under-water construction process."

Jan 1, 2015

By Kenneth Gavin, Weichao Li, Paul Doherty

"The lateral load capacity is one of the most important issues to be considered in designing piles to resist berthing loads, ship impact forces and for monopiles used in the offshore wind sector. A number of semi-empirical design approaches are available to calculate the ultimate soil resistance and assumed soil reaction profile along the piles’ embedded depth. In order to investigate the response of monopiles to lateral loading, a series of field experiments were conducted on instrumented steel pipe piles. Two lateral loading tests were performed on model piles with a diameter, D, of 340 mm and embedded depth, Lem, of 2.2 m, giving a Lem/D ratio similar to those adopted in the offshore wind sector. The piles were driven into dense sand at the University College Dublin geotechnical test bed site in Ireland. 10 pairs of strain gauges were installed on each model pile along the embedded depth at 10 levels to capture the load transfer and bending moment within the piles. The deflection and rotation at the model pile head were measured by Linear Variable Differential Transformer (LVDT) and inclinometers. The tests results were used to perform a detailed evaluation of current design methods. In the final section, discussion on the determination of the ultimate lateral load capacity for monopile design was conducted. IntroductionA pile’s lateral load capacity is determined, for design purposes, by two conditions: 1) the ultimate lateral load, Fu, divided by an appropriate safety factor; and 2) the load according to the maximum lateral deflection that the support structures can sustain. In view of the first condition, design methods to calculate the ultimate load were developed for piles used in the offshore oil and gas sectors, which tend to be much more slender than monopiles used in the wind industry. The purpose of this study was to investigate whether these design methods provide reasonable estimates of ultimate capacity, for short rigid monopiles.The methods to determine the ultimate lateral load generally follow three steps: 1) determine the ultimate soil resistance, Pu, along the pile embedded depth; 2) adopt the most appropriate soil reaction profile, Pz, along the piles embedded depth when the pile subjected to the ultimate lateral load condition (four of the most popular ones are depicted in Figure. 1); and 3) ensure equilibrium of lateral forces (see Equation 1, symbols are listed at the end of the paper) acting on the pile and bending moments (see Equation 2) about a point in pile is employed to determine the ultimate lateral load."

Jan 1, 2015

By Anup Kumar Mandal, Sanjoy Chowdhury, Biswajit Das

"Tailing pond of an iron ore mine necessitated raising the height of its embankment to create additional storage capacity. The tailing pond is located in eastern India and raising the height of embankment was going on during the month of January, 2014. Upstream method of construction was adopted since there was no space available at the downstream side. During the construction, about 200 m stretch of the north east embankment of height about 5.5 m failed forming a classical slip circle on the upstream side involving about half the top width of the embankment. To find out the root cause of the slope failure, detail geotechnical investigation work was carried out within the embankment as well as in the adjacent areas within the pond. About 7.5m thick very soft tailings were detected below the constructed embankment. Shear strength of the soft tailing was very low and was inadequate to sustain imposed embankment load. This resulted in the failure of the embankment. Analysis of the tailing deposit revealed that even after failure, settlement was continuing due to imposed embankment load. Under normal onedimensional consolidation, the tailing deposit would have taken about 5.7 years for 90% of primary consolidation. However, in order to mitigate the scarcity of storage space, mining plan required raising the height of the embankment within next six to eight months. Therefore, despite the fact that there was a failure, it was necessary to continue the construction on the underlying weak stratum. The system was redesigned with installation of prefabricated vertical drains (PVDs) to accelerate the consolidation process thereby gaining the in-situ strength. Strength was additionally enhanced by installing geogrids in multiple layers. It stabilized the existing embankment and also ensured construction of additional height over and above the existing embankment.INTRODUCTIONBeneficiation plant in the Iron mines enhances the mineral content by separation of contaminants and fines. The residue (waste material) is called tailings/tailings depending upon the grain sizes. These tailings in a slurry form are generally disposed in a pond called as tailing pond/tailing pond. Height of embankment of such ponds is increased either by upstream or by downstream or by centrally raising methods in different phases as quantum of deposition in the pond increases with time."

Jan 1, 2015