Search Documents

By Frank E. Cash

The work of the United States Bureau of, Mines is concerned primarily with the prevention of accidents in the mining, petroleum, and allied industries. This report analyzes the fatal accidents in the coal mines of Tennessee and gives the pertinent factors in tabular and descriptive form, with interpretations and suggestions to operators, workers, and the State Division of Mines for the future prevention or reduction of accidents in coal mines. ACKNOWLEDGMENTS This study was made possible through the cooperation of A. W. Evans, chief mine inspector of Tennessee, and his secretary, Miss Hiliary Penny, who made available the department records and assisted in the segregation and assembly of the data.

Jan 1, 1935

By Peter G. Groer

The commonly used exact methods (1-2) to determine the WL measure the total a activity or the total number of a counts during three preselected time periods. Due to the half-lives involved (TRaB = 26.8 min, TRaC = 19.7) I these methods take 3S minutes to complete the a activity Ra measurements. Methods using the total a counts, obtained at times less than about one RaB half-life after the end of sampling run into statistical 214 problems. These methods are almost blind to RaB (Pb214) as a consequence of its relatively long half period (see above) and the fact that RaB is a ß emitter. The way out of this dilema is to measure RaB directly through its ß activity. Since RaB's daughter Rae (Bi214) is also a ß emitter, the two f3 spectra have to be separated to obtain RaB alone. How this is accomplished 1s described in subsequent sections describing the theory of the IWLM and its calibration. 2.0 THEORY The IWLM samples air for two minutes and counts this airs ample for two minutes starting 3 sec after the end of the sampling period. The instrument has three channels. The lower a channel, the upper a channel, and one ß channel. The total RaA counts observed are accumulated in the lower a channel, the total RaC? counts are stored in the upper a channel. The total ß counts from RaB and RaC are recorded in the ß channel. These three quantities are functions of NA, NB, and NC, the unknown concentrations

Jan 1, 1975

By Edward Skolnik

The concept of using fluid dense media to separate heavy ore constituents from the lighter gangue dates back to 1858, when it was patented by Sir Henry Bessemer. Its use in coal did not begin until after 1917, however, when Chance invented a process (which bears his name) in which lighter coal floats in a suspension of fine sand in water while heavier refuse sinks. Conklin used fine magnetite in suspension as a medium for floating anthracite in 1922, DuPont designed a plant employing organic liquids in 1936, and Belknap used a solution of calcium chloride (which Bessemer had suggested, among other media) in 1937. Separation of magnetic media by magnetic separators from the suspensions in which they were carried was introduced in a Butler Brothers ore concentrator pilot plant in 1937. The media first used were crushed steel and various grades of ferrosilicon. Since 1940, when American Cyanamid used magnetic separators to recover and clean magnetite in a coal washing circuit, virtually all heavy medium circuits have been of that type. As long as static baths are employed, as they are in the processes above, coal smaller than 9.5 mm or 6.4 mm cannot be cleaned economically in heavy medium. The settling velocities of the fine material are very low, and consequently the time required to separate the lighter coal from the heavier refuse becomes excessive. In addition, stray currents in the vessel and the upward velocities induced to keep media solids in suspension affect the finer solids to the degree that physical size becomes a more important factor than specific gravity.

Jan 8, 1980

By Charles T. Harper

The uranium deposits discovered by Amok (Canada) Ltd. in the Cluff Lake area of north western Saskatchewan occur at or near the southern edge of the uplifted basement core of the Carswell circular structure. Two types of mineralization, distinguishable, by their geological and structural setting and mineral paragenesis, have been recognized. The N-Claude type is characterized by a relatively simple mineral assemblage, consisting of uraninite or pitchblende with coffinite, and is accompanied by variable amounts of graphite and organic matter, and Fe, Cu, Pb and Mo sulphides. Both N and Claude orebodies occur within quartzofeldspathic gneisses of the basement core. On the other hand, the D-type ore has a complex mineral assemblage consisting of: uraninite, pitchblende, thucholite and coffinite, along with native gold and selenium; gold tellurides, and selenides of Pb, Bi, Ni and Co; sulphides of Fe, Cu and Pb; and organic matter. The D orebody occurs within carbonaceous shales at the base of the Athabasca Formation as well as in fault zones in regolithic quartzo feldspathic gneisses above the inverted unconformity. An age of 1050 m.y., which is consistent with a period (circa 1200-1000 m.y.) of widespread hydrothermal activity and uranium mineralization or reworking within and adjacent to the Athabasca Basin, has been obtained from uranium mineralization from the D orebody. Later reworking (circa470 m.y.) of the mineralization occurred at the intersection of older mineralized shear zones with radial faults produced during meteorite impact.

Jan 1, 1978

By Marden Valente de Souza

Com o início da utilização do EPC, modelo matemático de previsibilidade de propriedade mecânica, no laminador de tiras a quentes da ArcelorMittal Tubarão em 2012 como ferramenta de acompanhamento da qualidade, pode-se verificar o comportamento das propriedades mecânicas ao longo do comprimento das bobinas logo após sua laminação. Baseado nestes resultados verificou-se que, principalmente, para material com espessura superior a 9,50 mm ocorria uma queda de propriedade mecânica do topo, região indicada para amostragem conforme norma, para o centro de aproximadamente 30 MPa, apresentando todos os valores aprovados conforme especificação da norma. Após verificação por ensaio físico na região central e comprovação da indicação do modelo, modificou-se o processo para garantir um produto com propriedade mais uniforme mantendo a garantia de atendimento às normas ao longo de todo comprimento.

Aug 8, 2018

By S. R. Titley

Carbonate-hosted massive sulfide (60%) ores of the western Cordillera compose a distinct class of deposits although they vary widely in detail and perhaps genesis. They have been important sources of lead, zinc, copper, silver, gold, and more rarely, molybdenum, tin, and tungsten in complex mineral assemblages usually dominated by pyrite. They occur as concordant stratiform bodies, as discordant mantos, and as chimneys crossing tens of meters of section; many are associated with faults and breccia bodies. Environments of formation of carbonate hosts range from craton basin to shelf with ages from Proterozoic to Cretaceous; in many instances, dating has shown mineralization to be significantly younger than hosts. Temperatures of formation determined for many deposits are high (200°-400°) and many districts are centers of igneous activity manifested by dikes, sills, and stocks. However, direct cause and effect relationships have been difficult to establish. Many important problems attend the renewed interest and study of these deposits and include questions of metal-sulfur sources, metallization processes and histories, geological controls at all scales, and relationships to broader patterns of metallogeny.

Jan 1, 1985

By A. E. Gooch

The Bureau of Mines conducted research in an attempt to provide a more sound basis for recommending improved artificial support during deepening of the main shaft of the Lucky Friday mine in the Coeur d'Alene mining district of northern Idaho. Field measurements of closure across the short axis of the 13-by 26-foot shaft were as high as 16 inches. Elastic/plastic finite-element (F/E) analyses were made, reducing the values of large-scale in situ rock mass properties until field closure measurements generally corresponded to displacements in the F/E analyses. Resulting plots of rock mass displacements, stresses, and areas of plastic failure display the results of creating openings (shaft, in this case) in deep mines in difficult ground conditions requiring artificial support.

Jan 1, 1976

By George W. Pawel

OWING largely to its value as a toughener and strengthener of steel for both industrial and military purposes, nickel is playing, an important role in the current war. It is fine of the metals in which the Allies enjoy a definite edge over the Axis nations and this time there is no place to which the Germans may send another submarine "Deutsehland" and expect to pick up a cargo of nickel to replenish their exhausted supplies. Total world nickel production thanks almost entirely to the expanded operation of the International Nickel Co. of Canada at Sudbury must now be at the rate of around 175,000 tons a year scarcely more than 5 per cent of which is accounted for by Germany, Italy and Japan. This represents more than four times the world output at the end of the first World War.

Jan 1, 1943

By A. Supomo, A. Partanen, M. Mular

Although many SAG operators may agree that on-line measurement of SAG feed-size is an attractive notion, applying this information in a control strategy that recovers the investment, engineering time, and maintenance is not necessarily straightforward. The P. T. Freeport Split-Online system was justified based on the assumption that SAG feed-size could be used in a feed-forward control strategy either at the regulatory or expert system control level. Something like “as the feed size changes adjust the throughput to avoid under or overloading the mill” was envisioned. However, following installation and calibration, Cluster Analysis showed that such an approach would not be successful. However, the sensor has been successfully integrated into Freeport’s grinding control strategy other ways. It provides an input to the Kalman filter parameter estimator used in a model-based control strategy that optimizes throughput and grind. The Split sensor also provides a characteristic feed size parameter for use in an on-line work index estimator. This paper describes the calibration and installation of the Split SAG feed-size analyzer, and reviews the evolution of its use in the Freeport C3 grinding circuit control strategy.

Jan 1, 2001

By W. M. Dressel

A simple, reliable field test for beryllium in rocks has been developed by the Rolla Metallurgy Research Center of the Federal Bureau of Minas. A small portion of the pulverized rock is fused with a sodium carbonate-sodium hydroxide flux in a wire loop. The fused mass is dissolved in water, a few drops of quinizarin solution are added, and the solution is viewed under ultraviolet light. A pink-to-orange fluorescence reveals the presence of beryllium in a sample containing as little as 0.013 percent beryllium (0.26 percent beryl). INTRODUCTION New and potential uses for beryllium make necessary a more intensive search for this metal, which is so similar to aluminum in its chemical reactions that it is not separated from aluminum in ordinary chemical analyses. The principal ore mineral of beryllium is beryl, a beryllium-aluminum silicate, which contains only 5 percent beryllium. This mineral is so similar to quartz in appearance that it is not always possible to distinguish one from the other in the field. While the distinction may be made easily with a petrographic microscope, few prospectors have access to such an instrument, and fewer still know how to use it.

Jan 1, 1960

By John J. Sammarco

Computer-related accidents have caused injuries and fatalities in mining as well as other industries. Normal accident theory (NAT) explains that some accidents are inevitable because of system complexity. NAT is a classic argument in organizational sociology although it has been criticized as having imprecise definitions and lacking criteria for quantifying complexity. These limitations are addressed by a unique approach that recasts this organizational theory into an engineering-based methodology to quantify NAT complexities of computer-based systems. In this approach complexity is categorized as external or internal. External complexity is defined by the external behavior of a system, and is quantified by these dependent variables: system predictability, observability, and usability. Dependent variable data contain the perceptions of 32 subjects running simulations of a system. The system?s internal complexity is characterized by modeling system-level requirements with the software cost reduction (SCR) formal method. Model attributes are quantified using 15 graph-theoretical metrics?the independent variables. Five of 15 metrics are correlated with the dependent variables as evidenced by structure correlations exceeding 0.25, with standard errors <0.10 and a 95% confidence interval. The results also show that the system predictability, observability, and usability decreased as NAT complexities increased. This research takes a step forward in operationalizing NAT for computerized systems. The research benefits mining and other industries as well.

Jan 1, 2005

By William L. Batt

FROM the time the Japs overran the Far East, the United Nations faced a serious military problem in the critical shortage of many raw materials desperately needed to prose¬cute the war on two fronts. For many months this critical shortage threatened substantially to limit the gigantic effort to get shooting equipment into the hands of the fighting men on the far-flung battle lines. Now this crisis has been met. Solvency in raw materials has been achieved. Simply stated, this job of producing solvency has been done by "cutting cloth to fit the garment." This does not mean that we have all the raw materials we need. Unfortunately, a few raw materials are still short, thereby limiting the total production of certain war goods, or making these goods less effective. Where the supply of raw materials is known to be limited, however, substitutions have been made or production schedules have been geared to the amounts available, and an over-all balance has been achieved between various parts of the war-production program.

Jan 1, 1943

By R. M. Beauchamp

Base metal processing operations often treat process tailings and acid mine drainage using a high density sludge (HDS) water treatment process. Lime is used in this process, which reacts with existing sulfates to form gypsum. When a recycle stream is incorporated in the process, gypsum levels in recirculating water may build up and cause high levels of gypsum supersaturation. Precipitation of gypsum from the supersaturated process water causes many problems. It is speculated that gypsum may precipitate on sulfide minerals and silica gangues in the flotation circuit, resulting in decreased selectivity and recovery. An understanding of the determinants and nature of precipitation may provide solutions to mitigate the formation of precipitates and improve flotation performance. This study showed that both sphalerite and silica exhibited gypsum- or calcium carbonate-like behavior in the respective supersaturated solutions, indicative of a coating of calcium species on the mineral particle surfaces. The addition of copper sulfate and/or potassium xanthate had little effect on the precipitation of gypsum or calcium carbonate on the mineral particles. Sodium carbonate is encouraging as a method to minimize calcium species interactions on sphalerite/silica surfaces.

Jan 1, 2006

By M Ogle

"Booster fans are relatively rare in Australian coal mines. However, as mines become progressivelydeeper it is likely that such fans will be increasingly adopted as a method to sustain or improve the ventilation of underground workings. The reasons why booster fans may be an att ractive alternative include: increased cost of sinking additional ventilation shafts with greater seam depths; environmental objections to shaft sinking projects; and increasing urbanisation and surface constraints limiting availability of potential ventilation shaft sites. As Tahmoor Colliery movedinto its northern lease the ventilation constraints became the limiting factor on production. Thelimitations of the old workings meant that the existing ventilation system would be inadequateto sustain the required production. Extensive ventilation modelling was carried out to evaluatevarious potential solutions and the recommended option was the installation of a booster fanor fans, to gain underground access to an already approved shaft site in the northern lease.Proposals were sought from recognised fan manufacturers and various alternative arrangements were tendered. Ultimately the choice was between one large centrifugal fan and a set (three or four) of smaller æauxiliary-likeÆ fans in parallel. The successful tender was for a single centrifugal, an arrangement very similar to the booster fans that have been operating eff ectively at Westcliff Colliery for a number of years. This paper describes the current ventilation network, evaluation of the ventilation options, the fan selection process, and the project status to date."

Jun 1, 2012

By Alan Galley

CMIC Mandate CIM Annual Meeting, Toronto, May 6, 2013 To increase mining research, innovation and commercialization efforts in order to strengthen Canada?s pre-eminent role as a global leader in mineral exploration, mining and knowledge-based services and technologies. To increase the supply of highly qualified graduates from mining and earth sciences faculties to meet the significant demand today and into the future of industry, governments and academia. The CMIC initiative is intended to develop long term research strategies that extend five or greater years. Such a research plan will underpin fundamental research and innovation and the training of HQP

May 1, 2013

Reduce accidents associated with handling of the electrical trailing cable and the water hose on mining equipment. Approach Two reels were mounted on a loading machine to store and release the lines as required during face operations. How It Works A hydraulic motor, which is actuated by a treadle valve in the operator&apos;s cab, controls the reel on which 50 feet of electrical power cable is stored. A spring motor resists unwinding of the other reel on which 50 feet of water hose is stored. Both reels are mounted on the right rear of the loading machine. See Figure 1. Following common mining practice, the cable and hose are anchored to fixed points at the first intersection outby the face. Tramming forward causes the cable and hose to be pulled from the reels. Depressing the treadle valve causes the electric cable reel to turn and wind-in any slack in the cable. The spring tension on the water hose reel automatically rewinds the water hose when the loader is trammed in reverse.

Jan 1, 1978

By David Oyler

Sonic travel time logging of exploration boreholes is routinely used in Australia to obtain estimates of coal mine roof rock strength. Because sonic velocity logs are relatively inexpensive and easy to obtain during exploration, the technique has provided Australian underground coal mines with an abundance of strength data for use in all aspects of ground control design. However, the technique depends upon reliable correlations between the unconfined compressive strength (UCS) and the sonic velocity. This paper describes research recently conducted by the National Institute for Occupational Safety and Health (NIOSH) aimed at developing a correlation for use by the U.S. mining industry. At three coreholes in Illinois, Pennsylvania, and southern West Virginia, sonic velocity logs were compared with point load tests for a broad range of coal measure rock types. For the entire data set, the relationship between UCS and sonic travel time is expressed by the following equation, where UCS is in psi and t is the travel time of the P-wave in microsec/ft. UCS = 468,000 x e-0.054t (1) The r-squared value for this equation is 0.87, indicating that a strong correlation between sonic travel time and UCS can be achieved with this technique. The paper also addresses the steps that are necessary to ensure that high-quality sonic logs are obtained for use in estimating UCS.

Jan 1, 2008

By V. I. Lakshmanan

Wastes when produced can be reused or recycled prior to disposal. Industries that cause environmental concerns during manufacturing include primary materials and primary metals. Pollution prevention mechanisms to achieve waste reduction require new separation, reclamation, control and process simulation technologies. Substituting recyclables for virgin resources will reduce energy use, water pollution, air pollution, water use and mining wastes. Shrinking landfill space will spur new technologies for waste treatment and recycling. These situations hence offer opportunities for innovative flowsheets with appropriate separation technologies. Development of innovative flowsheets to treat recyclables offer unique opportunities for process/product development, obtain green products and hence market advantage. The paper will illustrate with selected innovative flowsheets to treat recyclables.

Jan 1, 1996

By Robert L. Morris

A new concept of roof support by "sonic pin-setting" is introduced. Initial experiments indicate that this method could introduce tremendous benefits for the coal mining industry by making roof-bolting a faster, safer, and more economical operation. A theoretical model is presented for describing the process and an experimental machine was built. The present testing results are included.

Jan 1, 1977

By J. B. Hadaway

The current limit to power transmission for grinding mills through one mill pinion is approximately 7,500kW. Above this power rating either twin pinion arrangements or Gearless drives are required. The SMTP concept was developed to overcome this limitation by using two pinions with a single large drive motor. The SMTP mill drive offers major advantages in capital cost and greatly simplifies plant layouts, while using an innovative adaptation of industry-proven single helical gearing. Through the use of a single motor, provision of variable speed drive is greatly simplified. The SMTP can also be used for significant power upgrades on existing mills.

Jan 1, 2001