Search Documents

The dynamic breakage process of rocks by the impact of a hydraulic hammer is more complex than one normally assumes. It is even more difficult when one has to conduct the breakage under water. In such cases one does not know exactly what the surface topography and composition are at the bottom of the sea or river and, hence, it is more difficult to select the best position of the hammer before starting the hammering. Typically, an industrial hammer has a diameter of about 250 mm, a length of about 1.25 to 1.75 m and a mass of several tons. The hammer frequency can be up to 50 impacts per minute. The general principles of rock hammering can be easily summarized, but this knowledge is not sufficient to adapt adequately the method for less common rock conditions (e.g. less brittle rock, presence of vertical and subvertical fractures, etc.). That is the reason why we initiated a research project, whereby a scale model has been developed to conduct experiments in the laboratory and whereby discrete element simulations are being conducted. Both aim at a better understanding of the basic mechanisms of rock hammering. The scaled experimental model allows varying the impact energy and the static weight independently. Within the experiment, the hammer is in contact with the rock specimen under a certain confining pressure and with a certain contact pressure due to the static weight. A weight falls on the hammer, creating the dynamic action or impact; the height over which the weight falls can be varied. The penetration is recorded after each impact. After a certain penetration the test is stopped and the internal crack patterns are described. Some simulations have been conducted, allowing the modeling of individual fracture initiation and growth during the penetration of the hammer by either a constant displacement rate (using the UDEC-code) or by introducing the dynamic process (using the PFC-code). Some of the observed features in the laboratory experiments can be visualized in the simulations. However, further research is needed to allow the simulations being an adequate tool to well understand the dynamic process in laboratory experiments, as well as the in-situ behavior.

Aug 1, 2013

By L. L. Chasko

A mine fire is one of the most challenging safety issues facing a mine operator and can occur at any location underground. The National Institute for Occupational Safety and Health (NIOSH) and the Twentymile Coal Mine, Colorado, conducted in-mine experiments to determine the capability of high-expansion foam for addressing underground fires. The tests were conducted in sloping entries with high-capacity diesel-powered foam generators. The following results were observed: a well-designed, maintained, and properly operated high-expansion foam generator can propagate a foam plug hundreds of feet in steep upward sloping (20 pct) multiple entries against a ventilation pressure; stoppings and partitions designed to contain the foam plug in upward sloping entries must be substantially constructed; and the predicted quantity of foam concentrate can be significantly less than the actual amount used due to foam losses, such as bubble breakage on dry surfaces. This paper describes the production of high-expansion firefighting foam and discusses the in-mine experimental tests and results. DISCLAIMER: The findings and conclusions in this report are those of the author(s) and do not necessarily represent the views of the National Institute for Occupational Safety and Health.

Jan 1, 2009

By von Wielligh. L., D. G. Hattingh, M. N. James, W. Thomas

"SynopsisThe process of joining materials by friction is based on generating the heat necessary to create a solid-state mechanical bond between two faying surfaces to be joined. In simple terms, the components to be joined are subjected to frictional heating between rubbing surfaces, causing an increase in interface temperature and leading to localized softening of interface material, creating what is described as a ’third body’ plasticized layer. This plasticized zone reduces the energy input rate from frictional heating and hence prevents macroscopic melting. The plasticized layer can no longer transmit sufficient stress as it effectively behaves as a lubricant (Boldyrev and Voinov, 1980; Godet, 1984; Singer, 1998; Suery, Blandin, and Dendievel, 1994). The potential for this solid-state frictional joining process to create high-performance joints between, for example, dissimilar materials with limited detrimental metallurgical impact, and reduced defect population and residual stress level, has had a very significant impact on fabrication and repair in industrial sectors such as transport. This paper presents a brief overview of the advances made within the family of friction processing technologies that could potentially be exploited in the nuclear industry as alternative joining and repair techniques to fusion welding.Modern friction processing technologies can be placed into two main categories: those that make use of a consumable tool to achieve the intended repair or joint (friction stud and friction hydro-pillar processing) and those making use of a non-consumable tool (friction stir welding). The most mature friction joining technology is friction rotary welding, where a joint is formed between original parent materials only. A new addition in this category is linear friction welding, which opens the potential for joining complex near-net-shape geometries by friction heating. The continuous innovation in friction processing over the last 25 years has led to the development of a number of unique processes and applications, highlighting the adaptability of friction processes for specialized applications for high-value engineering components.IntroductionAssessing the potential for using alternative joining and repair techniques for specific applications in a given industrial sector is informed by an appreciation of the current size and potential growth in that sector. Power generation by nuclear fission has been out of favour over the past few years, due to several high-profile nuclear incidents, e.g. the Fukushima Daiichi nuclear disaster, as well as concerns over disposal of nuclear waste and spent fuel rods. However, due to rapid increases in the demand for electricity, coupled with many fossil-fuel fired plants reaching end-of-life, there is renewed interest in installing additional nuclear capacity."

Jan 1, 2015

By Chee Theng

"What would you do if you are an industry leader and disruptive technology threatens to overturn your business model? Although bearings and seals are in little danger of being displaced in the near future, one company is taking no chances in an age of digital disruption.“For SKF, digital transformation and the Industrial Internet of Things (IIoT) make this time right now arguably the most exciting time in our 100-plus years of history,” John Schmidt, president of SKF USA Inc., said during the SKF Technical Press Day in Philadelphia, PA.The company is not merely integrating digital technologies into its products and services but is taking a forward-looking, strategic approach. “To be successful, legacy companies have to undertake a process called digital transformation. It’s not just an IT initiative but is really about upgrading the strategic thinking,” explained Michael D’Argenio, vice president of digital transformation and customer experience at SKF Americas.Learning from those who went beforeD’Argenio cited the examples of two companies that saw entirely different outcomes in the face of digital disruption. The well-known case is that of Kodak, one of the storied brands in history, whose business was disrupted by the advent of digital photography. Although it invented digital photography, Kodak decided to box it up and put it on the shelf because it was scared of disrupting its business in photographic fim. Instead, it was disastrously disrupted from the outside.Less well known is the case of Encyclopedia Brittanica Inc., publisher of the longest-running English-language, general-knowledge encyclopedia in the world. Sales peaked at 120,000 sets in 1990, plunging to 8,000 sets in 2012. In 20 short years, it saw not one but two massive digital disruptions. The first was in 1993, when Microsoft published the first digital interactive encyclopedia on a CD-ROM, called Encarta, priced at just $99. The second was in 2001, when a communitycurated, free website called Wikipedia launched. Taking the opposite approach from Kodak, Encyclopedia Brittanica looked at its industry, its company and its customers through the lens of the new technologies, made a prediction about the future and, based on that prediction, took a bold move. Having identified its core value proposition as the delivery of reliable, high-value, verifiable knowledge, Encyclopedia Brittanica replanned, restructured and rebuilt its company from the ground up to deliver that same value proposition, only in a different way. It stopped producing the only product that it had known for 244 years and began producing digital products that it sold to educational institutions.“There is a lot to learn from the Encyclopedia Brittanica case,” said D’Argenio. “The company embraced its market change, it embraced its customer change, and it rethought what it needed to do to be successful. Because it owned that disruption internally, it was never disrupted from the outside. It continues to operate today and is as profitable as it has ever been.”"

Aug 1, 2019

By T. G. Joseph

A strain-softening constitutive relationship is introduced that describes the post-failure stress-strain curve for rock regardless of whether the rock is intact or broken. The core of this relationship is an ?apparent friction? concept that relates the post-failure apparent cohesive and frictional characteristics of the rock to the strain. The relationship can be determined for a given rock via a series of tri-axial strength tests establishing the peak strength and corresponding strain for a range of confining pressures, together with the determination of the base angle of friction via a simple tilt test. The postulates and assumptions used in deriving this relationship are verified from results of tri-axial tests on both intact and broken rock.

May 1, 2002

By Oliver Bradley

THE utilization of casing-head gas in the manufacture of casing-head gasoline by both the absorption and the compression method is a most important factor in the conservation of our natural resources.. Any industry connected with the oil business, in general, possesses particular attraction for a large number of people not conversant with its basic principles, for the reason that the large fortunes made in the production and utilization of petroleum and its products have been given undue prominence. The general impression of the public that enormous profits are to be realized in the casing-head gas industry with minimum expenditures of both capital and effort has, in a large measure, accounted for the phenomenal expansion of the industry in recent years and, likewise, has resulted in many mistakes and loss of investment funds. It is true that many installations have been very profitable, but such instances are always the result of careful planning, experienced judgment and conservative estimates. The inception and subsequent activity in the manufacture of casing-head gasoline, enabling the business to assume an important position in the petroleum industry, are of, comparatively recent origin, as its greatest growth, particularly in Oklahoma, occurred during the years 1917 and 1918. Much information must yet be secured and systematized concerning the methods of manufacture of gascline from high-yield casing-head gas, and a large field is still open for the application of accumulated experience and good engineering practice in devising better methods of extracting gasoline from casing-head gas of the poorer grades. The absorption process is coming into general use as a most efficient system of treating casing-head gas, and even so-called dry gas. In fact, there is a decided tendency toward the universal adoption of the absorption process as against compression methods. However, a general discussion of the relative merits of these two systems is not within the scope of this article.

Jan 9, 1920

By L. D. Johnson

On a project which is to develop a system to suppress coal dust explosions, a facility has been built and several devices tested. The facility is a 317-foot, 4.5-foot diameter shock tube and to date 53 tests have been carried out with methane-air and methane/coal dust-air as the explosive mixtures. Suppression of slowly propagating (up to 300 ft/sec) flame fronts has been successfully carried out on two tests using the dry chemical extinguishing agent Purple K. Delivery of the material directly into the flame front Seems to be required if effective suppression is to be accomplished.

Jan 1, 1972

In 2002 the authors updated the MFire model developed by the US Bureau of Mines. MineFire, developed by Mine Ventilation Services, Inc. (MVS), uses the MFire model to perform mine fire simulations on typical mine ventilation networks. The MineFire program is capable of producing visual schematics and other analysis tools for input and output of the MFire model. The MFire model, however, was limited to 500 branches and 10 fans. This paper discusses the newly modified MFire model that is now capable of modeling over 5000 branches and over 400 fans among other expansions and improvements. Given the long history and proven track record of MFire, the expansion did not modify the core calculation methods or results. This paper focuses on a general discussion of the MFire program and issues encountered in expansion of the algorithm. An example large network with simulation results is discussed.

Jan 1, 2011

By Nathan A. Tiner

Sulfuric acid anodizing process is extensively used in many industrial and consumer products to provide corrosion resistance to aluminum alloys. The anodic coatings produced consist of amorphous alhnum oxide with a pornus structure which is easily sealed and colored with dyes. The coatings may contain defects due to surface flaws, canposition and microstructure of the aluminum alloy, and/or due to the anodizing process conditions. This paper will describe the techniques used in anodizing process, various defects which may be produced in anodic coatings and the methods to control them.

Jan 1, 1992

Two Variable Real-Time Algorithm for Cone Crusher Control

Sep 13, 2010

By François Robert, Steve Green, Tyson Birkett, Dan Richardson

Abstract -Detailed sampling using a portable diamond drill, and interlaboratory comparison of selected samples have been combined with statistical studies of truncated populations to establish the gold content of several outcrops in the Val d'Or area. The outcrops chosen are non-mineralized. The background gold concentration in the rocks of the region is 5 ppb or Jess. Gold is distributed relatively homogeneously within the outcrops studied except for slightly increased concentrations within quartz-tourmaline veinlets. Three samples, of which 20 grams of powder are analyzed for each, can adequately determine the gold concentration of a structurally simple outcrop in the Val d'Or area.

Jan 1, 1992

By Zhang Hengzhong

Based on thermodynamics of surfaces and a proposed two-dimensional state equation for surfaces, the relationship between the surface tension (Y) of a solution and the activity (a1) of its component (i) was derived: (1/Y)r2-.¬E (ai/Yl) The derived equation was verified with reported experimental data of water-alcohol systems and water-acetone system, the calculated results showed astonishing coincidence with experimental. Applications of the equation to the five matte systems Cu2S-FeS, Ni3S2-FeS, FeS-PbS, Cu2S-PbS and FeS-Cu22S-PbS also demonstrated that at given matte compositions the calculated surface tensions agreed with experimental fairy well.

Jan 1, 1993

By D FitzGerald, S Jakica, R Paterson, J Silic

A new 2.5D airborne electromagnetic (AEM) algorithm has been developed by Intrepid Geophysics and Jovan Silic & Associates. The advantage of 2.5D (2D geology, 3D source) AEM inversion in 3D geological mapping applications and identification of conductive drilling targets, compared to the more commonly used conductivity-depth imaging (CDI) transforms or 1D inversions, are demonstrated using examples from banded iron formations (BIFs) and other geological settings. We show emerging AEM systems are capable of providing estimates of economic rock unit thicknesses, dips and fault definition at an accuracy that mitigates the need for pattern drilling.The 2.5D inversion application used in this work and described in Silic et al (2015) is a substantially changed version of ArjunAir (Wilson, Raiche and Sugeng, 2006), a product of CSIRO/AMIRA project P223F. The changes include a new forward model algorithm and a new inversion solver. The application enables the accurate simulation of 3D source excitation for full domain models inclusive of topography, non-conforming boundaries and very high resistivity contrasts. Solution is accurate for a geoelectrical cross-section, which is relatively constant along a strike length that exceeds the AEM system footprint.The major innovation includes a new inversion solver with adaptive regularisation, which allows the incorporation of a misfit to the reference model and the model smoothness function.Memory usage has been dramatically reduced and is estimated prior to execution. For speed the software has been parallelised using Intel message passing interface (MPI) and can be used on standard computing hardware or computing clusters. Data from survey lines with lengths exceeding 100 km can be inverted on high end laptop computers.We allow flexibility in the selection of components and in the estimation of noise.AEM inversion examples are shown for surveys from BIFs, base metals (volcanogenic massive sulfides) and geological mapping projects and the results are compared with known geology and drilling. We demonstrate the much improved mapping and target definition delivered by this inversion method when compared with the other more common transforms or inversion methods used on these projects.CITATION:Paterson, R, Silic, J, FitzGerald, D and Jakica, S, 2017. High accuracy .D airborne electromagnetic inversion method for banded iron formation and other geological settings, in Proceedings Iron Ore 2017, pp 319–330 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By John W. Nebgen

This report contains findings from a U.S. Bureau of Mines study concerning the inhibition of acid mine drainage formation from underground coal mines. A series of experiments was performed in which three different pyritic materials (wastes from coal production plants) were evaluated using several candidate inhibiting agents. Data obtained from the inhibitor-treated pyrites were compared with data from control experiments in which untreated pyritic wastes were used. The experiments were conducted by placing treated and untreated pyrite in columns, passing moist air through the columns to promote oxidation of pyrite, and washing the columns weekly to collect oxidation products for analysis. Experimental results indicate that quantities of acid mine drainage can be substantially reduced if soluble iron III (ferric) ion is controlled. The best inhibitors are neutral or alkaline siliceous materials such as fly ash, blast furnace slag, portland cement, and cement kiln dust. These materials appear to insolubilize iron III species to make them unavailable for reaction with pyrite. The data strongly suggest that the soluble ferric ion aqueous is a key oxidant for pyrite to produce acid mine drainage. The role of aqueous ferric ion as an oxidizing agent is substantiated further by data obtained using metallic iron (nails) as an inhibitor. The iron nails tended to keep the soluble iron in the iron 11 (ferrous) state. Experimental results indicate that sulfate and acidity levels are reduced when pyrite is in contact with the metallic iron.

Jan 1, 1979

By Saulo Brinco Diniz

O presente trabalho estuda as características microestruturais e mecânicas de 3 ligas de alumínio (1100, 3104 e 8011) na condição laminada a quente e submetidas a um tratamento térmico de solubilização em diferentes tempos de encharque (1, 2 e 3 horas). As ligas em estudo apresentam um percentual de soluto ligeiramente acima do limite máximo de solubilidade nas mesmas. Assim os tratamentos térmicos de solubilização permitiriam controlar a dimensão, dispersão e natureza dos precipitados presentes modificando a condição laminada a quente, sem atingir a completa dissolução dos mesmos. A avaliação microestrutural/ composicional e mecânica foi feita por Microscopia Eletrônica de Varredura (MEV)/ Espectroscopia de Raios-X de Dispersão de Energia (EDS), Difração de Raios-X (DRX) e ensaios de dureza. De acordo com os resultados apresentados para as ligas 1100 e 8011 o tempo para ocorrer à solubilização está entre 1 e 2 horas enquanto que para a liga 3104 está entre os tempos de 2 e 3 horas.

Aug 7, 2018

By Ramon Valls Martin

A obtenção das propriedades magnéticas do rejeito do processamento do minério de ferro auxilia na determinação da viabilidade da recuperação do ferro residual. Também permite a otimização dos parâmetros operacionais do processo de concentração por separação magnética. Foram apresentados dois métodos de caracterização magnética: Método indutivo (histeresígrafo) e método de força magnética (balança de susceptibilidade). Estes métodos têm como vantagens o baixo custo e rapidez de execução. Apresentaram sensibilidade suficiente para a caracterização de amostras de resíduos com teores de ferro muito reduzidos.

Aug 16, 2017

By S Khosrowshahi, A Weeks, W J. Shaw

"To provide an indication of expected performance of the mine and mill, feasibility studies should include an assessment of the expected day-to-day variability in process plant feed. Attempts to do this based on conventional resource models will be flawed as such studies fail to consider and account for the in-built smoothing (averaging) of input data.This can lead to one of two situations: an expensive, over-engineered process plant that can cope with every possible situation, or operational strategies that fail to manage the natural variability within the orebody and the impact of day-to-day operational decision-making.In both cases the value of the project diminishes through excessive capital costs or reduced throughput or recovery during operations.Unlike conventional estimation techniques, the geostatistical method of conditional simulation can reproduce the inherent variability of the deposit. Once a valid model has been developed, it is possible to analyse the model using a transfer function that simulates the proposed mining processes and provides a representation of the likely variation of mill feed characteristics at any time scale.The case study demonstrates how the proposed mining strategy would result in mill feed being considerably more variable than expected, resulting in poor recovery, low throughput and potential breaches of environmental conditions. Mitigation measures included budgeting for additional mining equipment to enable greater flexibility during mining and revised stockpiling and crusher feed strategies.Awareness of the benefits of modelling the variability of geometallurgical parameters will increase the use of this approach in producing more realistic financial models of expected mine performance at the design stage.CITATION:Shaw, W J, Khosrowshahi, S and Weeks, A, 2013. Modelling geometallurgical variability - a case study in managing risk, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013, pp 247-252 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 29, 2013

By R. V. Ramani

This volume, the first of a six volume final report, provides an executive summary of the research and results carried out under a grant from the U. S. Bureau of Mines on underground coal mine ventilation. Under the project, a mine ventilation simulator was developed. Sensitivity of leakage and friction factors on the total quantity and pressure requirements was studied. The simulator was applied to a new mine under development, and to an operating mine, to demonstrate the usefulness of the simulator in ventilation planning and in evaluating proposed changes to existing ventilation system. The titles of the other volumes are as follows: Volume II: Mine Ventilation Network Theory Volume III: User's Manual for PSU/MVS Volume IV: Sensitivity of Leakage and Friction Factors Volume V: Application of PSU/MVS to Ventilation Planning of a New Mine Volume VI: Application of PSU/MVS to the Analysis of Modifications to Existing Ventilation Systems

Jan 1, 1977

The drill steel' sharpening shop, which stands adjacent to the Chaffers shaft, is built to the dimensions of 110 ft. 9 in. by 58 ft. wide, and is air conditioned in order to maintain reasonable working conditions during the summer months.Figure 1 is a plan of the shop, showing the disposition of the machines and equipment.LIST OF STEEL SHOP EQUIPMENTAir Conditioning Plant comprising:-1 Spray and Eliminator Type Air Cooler, 6' ft. x 7 ft. x 6 ft. with 80 fine sprays.1 No. 36 Keith type ER. Ball Bearing upcast multivane centrifugal fan.20,000 cfm. a in. WG. at 450 r.p.m.Fan motor, A.G.E. S.C. 10 h.p. 1,160 r.p.m.1 Water Pump. 2?!-3-in. Thompson Class G. Single Stage Centrifugal Pump.1 Pump Motor, A.G.E. S.C. 70 h.p. 1,160 r.p.m.Drill Steel Sharpening Equipment:-2 Holman Sharpening Machines, No. 11.1 Ingersoll Rand Sharpening Machine, No. 54.5 Ingersoll Rand Sharpening Machines, No. 50.2 Holman Hot Millers, Type DM. Double Spindle Machines.2 Morgan Hot Millers, Type 1.6 Reamers consisting of motors with Ingersoll Rand Chuck fitted to the shaft and carrying a reamer of i-in. square Ultra Capital Steel Motors, A.G.E. S.C. 1 h.p. 1,160 r.p.m.4 Double-sided Drill Sharpening Furnaces, oil fired with L.P. "Major" 2-in. non-rotary whirl type burners.Combustion Chamber, 2 ft. 4 in. x 6 in. x 12 in. Oil consumption, 3·3 to 3·8 gallons per hour.Furnace Lining, Standard Kyanite.Firebricks, 9 in. x 3 in. x 4 in.2 Moving Frame type double-sided tip hardening furnaces, oil fired using High Pressure Air reduced to 3 lb. per square inch.Combustion Chamber, 3 ft. 5 in. x 5 in. x 16 in.Burners, "Major" L.P. 2-in. non-rotary whirl type.Oil consumption, 3·3 to 3'8 gallons per hour.Furnace lining-bottom and sides, 60 only 9 in. x 3 in. x 4 in. Kyanite bricks.

Jan 1, 1941

By R J. Johnson

The development of "SANFO" has provided the Mining Industry with a LOW COST HIGH GAS VOLUME, VARIABLE DENSITY, Blasting Agent which can be blended "On Site" in a simple Agitator mixing and charging system by mine site employees.

Jan 1, 1996