Search Documents

The Resource Management Act 1991 (RMA) and the Crown Minerals Act 1991 (CMA) both came into force on 1 October 1991. The purpose behind RMA was to integrate the existing laws dealing with town and country planning, land subdivision, water and soil, minerals and energy resources, coastal management, air pollution and noise control into one omnibus Act. Originally, there was a section in RMA dealing with minerals. However, this section was taken out of RMA and a companion piece of legislation - namely CMA - was passed with RMA.

Jan 1, 1994

By R. H. Grau, A. Sainato, S. J. Schatzel, T. M. Kohler, A. T. Iannacchione

This Bureau of Mines research study found gas emission rates from an advancing face, and flows and pressure of gas from an exploration drill hole were dependent upon the geology of salt encountered in a domal salt mine. Normal production-grade "pure" salt adjacent to an anomalous' zone was found to have a methane emission rate of less than 5 ft3/ ton (0.1 m3/t) of mined salt from a room advanced by a continuous miner. Extremely low gas flows [less the 4 ft3/h (0.1 m3/h)] and lack of pressure buildup were also observed from this normal salt in a 154-ft (47-m) exploration drill hole. These data indicate that methane emissions should not be a problem when mining in this type of salt. In the adjacent anomalous zone, methane emission rates ranged from 15 to 70 ft3/ton (0.4 to 1.8 m3/t) of mined salt from an advancing face. Gas flows of approximately 42 ft3/h (1.2 m3/h), and pressures in excess of 900 psig (6,200 kPa) were observed in an exploration drill hole when the anomalous zone was encountered. This information suggests a greater methane emission hazard from the anomalous zone than from the associated normal salt. If this trend of increasing emissions problems associated with anomalous zones of salt is common with similar anomalous zones encountered or observed in other domal salt mines, then special control strategies should be employed to minimize this potential mining hazard.

Jan 1, 1984

By James E. Hoffmann

Oxidative pressure leaching is gradually supplanting other techniques for the decopperizing of slimes. The reasons for this include: much more rapid reactions, more compact equipment, a reduced environmental burden, and perhaps most important, a much lower final copper concentration in the decopperized slimes. This paper will discuss the reactions occurring during decopperization, the acidity and temperatures encountered and the techniques employed for discharging non condensable gasses. A spreadsheet is provided which allows adjusting the operating conditions depending upon raw (undecopperized) slimes composition, solids concentration and lixiviant composition. A typical process equipment flowsheet is provided along with a process narrative.

Jan 1, 2000

By Charles J. Zablocki, Robert J. Kamilli

"Abstract - Buried, possibly mineralized granite cupolas at the Silsilah tin deposit in Saudi Arabia (lat. 26°06' N, long. 42°40' E) have been successfully located using a closely spaced electric-field-ratio profiling technique. In this study, electrical fields at 27 and 270 Hz across grounded electrodes spaced 50 m apart were measured along six traverses. This method is interpretable by inspection, unlike the dipole-dipole technique, which requires mathematical modeling for interpretation.In the study area, the technique allowed the authors to identify and distinguish among unroofed granite cupolas, cupolas with their aplite-pegmatite apical contact zones intact, strong (quartz-rich) and weak (relatively quartz-poor) greisens, dikes, faults, and pervasively argillized rocks.This method should be useful in the valuation of other shallow mineral prospects in similar settings in other parts of the world, especially deposits for which the location of vertical contrasts is important, such as veins or mineralized zones associated with the apexes of small igneous cupolas."

Jan 1, 1993

By R. A. Williams

Surface and electrochemical techniques have been used to describe the surface chemistry of ferrosilicon powders, as a function of pH and electrochemical potential, for conditions typical of operating DHS plants. The practical consequences on the likely corrosion behaviour and associated electro- kinetic particle-particle interactions (which affect stability to sedimentation) in the suspension, are discussed.

Jan 1, 1987

By Paulo Chaves, Márcia Gonçalves, João R. S. Carvalho, Fernando J. A. S. Barriga, Edgar Carrolo, Tiago Luna, Ricardo Rato, Anabela Bento

INTRODUCTION For the last decades, deep-sea marine resources such as seabed massive sulfides (SMS), polymetallic nodules and ferromanganese crusts (Fe-Mn crusts) have received an ever- increasing amount of attention worldwide for their abundance in critical metals and potential commercial value. This interest has mostly been driven by the growing world demand for raw materials, in particular for high- and green-technology applications (e.g., hybrid and electric cars, batteries, photovoltaic solar cells, cell phones, super magnets), as well as by industrialized countries governments other than BRICS states need to secure a more diversified supply of metals, resulting in a new deep ocean exploration boom. Since the oceans and its resources are increasingly seen as indispensable for humans needs and their challenges in the decades to come, this boom increments pressure on marine areas, either in international or within countries economic exclusive zone (EEZ). Since 2002, the International Seabed Authority (ISA) has signed up 29 contracts with several entities and national governments from multiple countries (e.g., Japan, China, Germany, France, Russia, India, Rep. of Korea, UK, Canada, Brazil) for exploration for deep-sea mineral resources in international waters, either for scientific or commercial proposes, which together cover over 1.3 million km2 [1]. In turn, over 300 exploration licenses, covering more than 650,000 km2, have been granted within the EEZ of Pacific countries such as Papua New Guinea, Tonga, Fiji, Solomon Islands and Vanuatu [2, 3]. This number is expected to increase very rapidly, as 77 countries have proposed to the United Nations the extension of their continental shelf in order to extend their EEZ and jurisdiction over potential deep-sea mineral resources [4]. Its estimated that 42% of the potential areas for SMS occurrences, 54% for cobalt-rich Fe-Mn crusts, and 19% for polymetallic nodules lie within the EEZ of coastal countries [5]. In addition, a huge amount of seafloor is yet to be explored and evaluated. Combined, the size of the granted exploration areas represents less than 10% of the overall area thought as most favorable for the occurrence of the 3 types of deep-sea mineral resources above mentioned. This means that today’s assessments on deep-sea mineral resources are only a rough approximation.

Jan 1, 2018

Poorly designed sampling protocols generally result in high project risk by artificially increasing grade variability (ie the nugget effect). Sample collection, preparation and assay protocols that suit the ore type, together with QA/QC systems, will reduce this risk. All reporting codes (eg JORC, 2004) require the Competent Person to consider the quality and implication of sampling and assaying programs. High sampling errors beget higher project uncertainty; despite this fact, sampling does not receive the attention it deserves. The case studies presented show that many sampling issues frequently go unrecognised or unaddressed, resulting in poor project decisions during exploration through to feasibility and production. The overall conclusion is that correct sampling is critical to mining project success and that there is often a need for its optimisation.

Jan 1, 2007

By William C. Peters

The Alpine-Himalayan system, the only major active tectonic belt mainly exposed in a continental mass, is of increasing interest to exploration geologists as well as to theoreticians. Answers to the broader problems of plate tectonics are being sought in this intricate system where the geosynclinal concept was born and where the geotectonic cycle was first applied to metallogeny. The search is all the more intense because it involves scientists from more than a dozen countries with a stimulating variety in perspective. The international Geodynamics Project has allocated the Alpine-Himalayan system to two separate study groups with one directing its attention to the Alpine-Mediterranean region and the other giving consideration to the Himalayan region. This geographic division is accepted in this paper, with remarks being confined to the former and to the west of boundary zone between the European-Asian and the Southeast Asian plates as envisioned by Dewey and Bird (1970). The region is well-mapped in some parts and it includes some of the most intensely-studied geology, most classic mines, and newest orebody discoveries. Within the region, an Alpine-age copper-molybdenum metallogenic belt extends from Rumania to Pakistan. The belt can be considered in terms of plate tectonics, and there is the possibility of using plate tectonics concepts in exploration.

Jan 1, 1973

By N. Voennann

Stillwater Mining Company operates an electric furnace at its smelter in Columbus, Montana to treat a Ni-Cu-platinum group metal concentrate along with secondary PGM bearing materials. Hatch Associates has designed several improvements to this furnace, which was originally built by others. Implementation of these relatively low cost improvements has resulted in substantial increases in furnace availability and capacity, along with reduced unit costs. ? The improvements included: ? Installation of water-cooled copper cooling elements to stabilize refractory wear and increase furnace life.- ? Improved furnace 'bindings, to enhance the furnace's structural integrity by improving the contact between the refractory and cooling elements, and by promoting tight brick joints resistant to matte or slag leaks. ? Adjustment of the electrode regulator to allow higher furnace power levels. ? Installation of an automated air-slide (aeration conveyor) feed system to evenly distribute the furnace feed in an insulating layer on the bath surface. This "black-top" practice reduces unit energy costs and makes available additional smelting capacity.- ? Electrode seals to reduce ingress of air that absorbs heat before exiting the furnace in the off-gas stream. The saved energy can be used to smelt additional concentrate. This paper describes the above furnace modifications, and the benefits derived from their implementation.

Jan 1, 1998

By Frank Gómez, Solange Ríos, Jean Valencia

La eficiencia y evolución de las actividades de perforación y voladura son de gran relevancia en la actualidad debido al impacto que causa en los procesos posteriores dentro de las operaciones mineras. Sin embargo, esta actividad unitaria experimenta numerosos problemas operativos debido a la mala elección de la malla de perforación y del explosivo, lo cual causa sobre-excavación, mala fragmentación, dilución y pérdida de mineral, entre otros. El objetivo de este trabajo técnico es optimizar las actividades de perforación y voladura de la Unidad Minera San Rafael aplicando los modelos de rotura y predicción de cavidades.

Sep 30, 2022

Some crystal chemical properties of several apatites from Brazilian deposits and occurrences were determined; the samples had different origins (igneous, metamorphic and sedimentary). The aim was to establish relationships to their froth flotabilities behaviour. Detailed X-ray diffraction studies were carried out, to determine precisely the unit cell parameters and the degrees of crystallinity of the apatite samples. A thorough chemical analysis of these minerals was also conducted. Microflotation studies were carried out, using sodium oleate and dodecylammonium chloride as collectors. The crystallinity levels were determined for all samples studied, with the establishment of a crystallinity index, which varied from 10.0 to 4.5, on a normalised scale. A marked dependence was observed between this crystallinity sequence and flotability; for both collectors, flotability dropped drastically for crystallinity indices lower than 8.0. Also, the low crystallinity apatites showed a decrease in floatability, for longer conditioning times.

Jan 1, 1993

By Gabriel Böde Jimenez Leon, Michael Karmis, Christopher Newman, Zach Agioutantis

"When utilizing high recovery underground mining methods, such as longwall or high-extraction room-and-pillar mining, the movement and deformation of the overburden propagate toward the surface and may affect the integrity of overlying surface streams (Peng et al, 1996). Published studies cite three major mechanisms of subsidence as most likely to impact streams: displacement, slope and strain. While subsidence-induced vertical displacement cause little structural damage to the stream bed, it may create adverse drainage and stream flow issues as the subsidence trough allows for ponding (Dawkins, 2003). Subsidenceinduced changes to the slope, or tilt, of a stream may have adverse effects on water flow. As the stream enters the subsidence trough, the gradient increases providing potential erosion control problems. When exiting the subsidence trough, a reduction of the gradient may inhibit stream flow, causing localized ponding (Peng, 2008). While vertical displacement and tilt both may have detrimental effects to surface streams, the resulting strains have been documented as being the most damaging to surface streams and structures causing distortion, fractures, or failure (Singh, 1992). When stream beds are subjected to high tensile strain, tensile cracks may form at the surface level allowing for the direct loss of stream flow through fissures. When stream beds are located in areas of high compressive strain, rock layers forming the stream bed can fail as the stream bed ruptures, upward, blocking stream flow or having the stream diverted into the fracture zone at the base (Iannacchione, et. al., 2010).Recent investigations on the effects of underground mining on surface bodies of water suggest that to determine the degree of stream impact one must also consider the geologic structure and thicknesses, surface topography, watershed drainage areas, width of river bed and rate of mining. Due to the complex nature and number of parameters affecting surface streams, subsidence modeling tools and software packages should be implemented throughout all stages of subsidence planning, prediction and control. The Surface Deformation Prediction System (SDPS) utilizes the influence function for the calculation of final subsidence deformations with respect to the angle of influence, supercritical subsidence factor as a function of the percent hard rock, edge effect offset distance, and surface topography. Developed more than 25 years ago, SDPS has been continually updated with new analysis and prediction features, providing a reliable and versatile program for subsidence management methodologies. Most recently, the program has been updated to evaluate the effect of varying surface topography in the prediction of horizontal displacements, referred to as ground strain, allowing for the accurate three-dimensional representation of surface deformations in mountainous terrain (Agioutantis and Karmis, 2014). Ground strain has become one of the predominant deformation indices used in the evaluation of potential damage to surface structures (Karmis et al., 1995). Ongoing work with SDPS software seeks to investigate the calculation of ground strain in SDPS and its ability to accurately and realistically predict damage to surface streams due to underground mining operations."

Jan 1, 2015

By C. W. Eggert

This paper gives an account of the E.V.O.P. tests made at the Copper Rand mill of the Patino Mining Corporation in Chibougamau, Quebec. The runs were made to acquire an understanding of the method. A description of events, along with conclusions, observations and opinions, is out-lined.

Jan 1, 1967

By P. S. Arthur

The copper I SAS MELT? process is a submerged lance bath smelting technology. In the 20 years since the process was first demonstrated on a semicommercial scale at Mount Isa in north-west Queensland, Australia, copper ISASMELT? plants have been constructed to treat concentrates or secondary raw materials around the world. The process is operating in smelters in Australia, the USA, Belgium, India, Germany, China and Zambia. ISASMELT? plants have been installed to improve the environmental performance of operating smelters and reduce costs for smelting companies. A new copper furnace is being commissioned at Southern Peru Copper Corporation in early 2007, while more furnaces are under design for installation in Kazakhstan and Peru. Copper ISASMEL T? plants are supplied as complete technology packages including engineering design services for the furnace and key ancillaries, supply of core equipment, provision of intensive training programs in operating plant environments and commissioning assistance services. The proven technology transfer process ensures successful implementation of submerged lance bath smelting into large scale plants. This paper summarises developments at recently constructed copper ISASMELT? plants.

Jan 1, 2007

By H. Abdollahi

Cold rolling is one of the most important techniques in metal forming since the cold rolling products are almost finished product, The product quality of this process is widely influenced by friction in the roll gap; therefore, controlling the friction and other parameters affecting the cold rolling is very important in order to have a product with high quality, Among the cold rolling parameters, the pressure distribution or friction hill within the roll gap is known as the most significant one, In this study, a new software (Matroll), is introduced which can determine the coefficient of friction (COF) and plot the friction hills for an industrial mill, Besides, based on rolling equations, it offers about 25 rolling parameters as outputs. To verify the software operation, the real industrial rolling data was used as inputs, The results (outputs) are in good agreements with the findings of other researchers, The COF values are very reasonable, The friction hill shows that COF is not constant over the whole arc of contact.

Jan 1, 2005

Sheaves are a critical safety component in a winding system and are expected to survive such extreme loading events as rope break. Sheave designs have often been developed and evolved empirically, consequently many existing sheaves are not necessarily subjected to the detailed analyses that are possible using todayÆs design tools. The design philosophy for sheaves is that the rope should be the weakest link in the system so that associated equipment can function safely for any load up to rope break. A number of failure mechanisms must be considered, but buckling is often prominent. During the course of investigating the feasibility of upgrading the hoisting capacity of a winding system, the capacity of all critical components was reviewed. The sheaves in the system were found to have insufficient spoke buckling capacity for the specified rope. A proposal to increase the spoke buckling capacity by connecting spokes together using a simple tie arrangement was evaluated and found ineffective. An alternative tie arrangement concept was developed and evaluated and shown to be adequate. This paper describes the finite element model, analysis approach and results for the original sheave and the two modifications. The contribution of the sheave rim to the total buckling capacity is evaluated. Some practical issues for spoke tie modifications are discussed.

Jan 1, 2005

By C Chen, T Kan

The distribution ratio of Pb (LPb s/m) between three types of slags (FeOx–SiO2, CaO–FeOx and FeOx– CaO–SiO2) and molten copper after equilibrium was measured at 1300°C and oxygen partial pressure (pO2) of 10-10–10-6 atm. Results showed that for FeOx–SiO2 slag, the LPb s/m increased from 0.024 to 2.57 with pO2 increased from 10-10 to 10-6 atm. The LPb s/m with CaO–FeOx slag was lower than the FeOx–SiO2 slag at the same pO2, ranging between 0.015 and 0.53. Using the FeOx–CaO– SiO2 slag generated LPb s/m values (0.02–1.6) in between. The oxygen partial pressure in the investigated range had no obvious effect on the activity coefficient of PbO (γPbO) which was averagely 0.44, 1.70 and 0.71 for FeOx–SiO2, CaO–FeOx and FeOx–CaO–SiO2 slags, respectively. The increases in the (CaO+MgO)/SiO2 mass ratio of the FeOx–CaO–SiO2 slag induced the decrease in the LPb s/m and the increase in the γPbO value. However, the variation in the Fe/SiO2 mass ratio didn’t exert obvious effects.

Jun 19, 2024

Energy Savings and Technology Comparison Using Small Grinding Media Considering the complexity of minerals, the need for finer grinding is increasing along with the energy cost. However, energy is increasing exponentially when grinding finer with conventional grinding balls. The use of small grinding media represents the best potential to improve energy efficiency. Today, it is possible to use grinding media as small as 1 mm. How do they perform in industrial grinding mills? The use of small grinding media (5 - 12 mm), called Millpebs, in regrind mills proved that finer grinding can be achieved at lower energy consumption. In ball mills, energy savings vary from 10 per cent to 40 per cent compared to 25 mm media. A regrind ball mill with a mix of small grinding media can be as energy efficient as an Isa Mill charged with 2.5 and 3.5 mm beads. In vertical stirred mills, energy savings vary from 30 per cent to 60 per cent. To carry out the same final grind, a vertical stirred mill with Millpebs will consume at least 60 per cent less energy than a ball mill using 25 mm grinding media. More potential savings were identified. To achieve those improvements, some operating conditions must be met: 1) feed size should be less than 250 ¦m; 2) the pulp must be fluid enough; 3) finally, the slurry linear velocity should not be excessive. This paper talks about all those industrial results improvement and operating conditions.

Sep 13, 2010

By Deborah Shields

Aggregate is an essential input to every economy, so governments need to ensure a sustainable supply of these resources through planning. There is also a need to shift from a linear economy to a more circular one, in which wastes are recycled rather than landfilled, so as to increase eco-efficiency. The purpose of the Sustainable Aggregates Planning in South East Europe (SNAP-SEE, SEE/D/0167/2.4/X) project is to develop a Toolbox for Aggregates Planning to assist governments and stakeholders in national, regional, primary and secondary, aggregates planning in southeast European countries. The Toolbox comprises documents on stakeholder consultation, data and analysis methodologies, a vision of best practices in aggregates planning and how to build an aggregates plan. The Toolbox will also support ongoing efforts to enhance minerals policy in the European Union (EU) as called for by the European Innovation Partnership on Raw Materials. Industrialized and developing nations see long-term and continued economic growth as essential to the well-being

By P Salmon, M Kennedy

Sun Metals Corporation Pty Ltd (SMC), a wholly owned subsidiary of Korea Zinc Co Ltd (KZC) is a company formed to develop, construct and operate a zinc refinery, 11 km south of Townsville in North Queensland. The project opportunity exists because of on-going consumption growth for refined zinc metal, technological, environmental and economic obsolescence of existing zinc processing plants, and a prolonged ædroughtÆ of new zinc processing capacity under construction. The Project will utilise proven technology developed by KZC at the Onsan refinery in Korea. The Townsville Refinery has been designed to be the most environmentally-friendly zinc refinery in the world, and in particular to resolve the issue of secure, long term treatment of the ironbearing content of the zinc raw materials.

Jan 1, 1998