Search Documents

By J T. Woodcock

This paper discusses characterisation techniques that can be applied to complex waste products from metal production and processing operations with the aim of devising treatment methods for upgrading the metal content for recycling. Two waste streams were selected to illustrate the role of characterisation in adapting mineral processing techniques to provide an effective recycling strategy. Waste products chosen were:aluminium dross, which contains metallic aluminium particles in a coarse matrix of many components; and steel shredder sludge that contains copper wire and other metallics in a matrix of plastic and natural fibres, iron oxides, metallic iron, and other compounds. Characterisation methods discussed include chemical analysis (XRF, ICP-AES, and selected specialised techniques), phase analysis (XRD, SEM, TEM, and optical microscopy), morphology (IFESEM), sizing analysis (screening, Cyclosizing, Infrasizing, Malvern sizing), and general techniques such as particle shape, surface area, and porosity determinations. The applicability of these techniques to the waste products is considered in relation to their advantages and disadvantages, and sampling issues.Treatment techniques considered for the two waste products included comminution, screening, air or water classification, simple water leaching, gravity separation, magnetic separation, flotation, and eddy current separation.Tentative flow sheets were developed for the two wastes. For aluminium dross, it was proposed to use fine crushing followed by water washing to remove soluble chlorides and aluminium nitride, and then desliming followed by flotation of the granular fraction to give a metallic aluminium-rich concentrate. For shredder sludge, it was proposed to use wet screening, water classification, and gravity concentration to produce a copper-rich product and magnetic separation to produce a metallic iron-rich product.

Jan 1, 2004

By P. O. Parfitt

At the McIntyre mine, there are two distinct operations: a gold mine with narrow veins, mined by cut-and-fill methods, and a copper mine with large, open, long-hole stopes. The application of the Critical Path Method to scheduling work in the copper mine, where it has been used successfully for several years, is de-scribed briefly. This application is relatively simple. Use of C.P.M. has now been extended to the gold mine. To replace the former method of scheduling from bar-charts, a procedure was developed for scheduling automatically. To handle an operation of this size and complexity, a computer was essential. Improved schedules are now being produced, with a saving in time.

Jan 1, 1967

By A Giblett, M Daniel

"The Global Mining Standards and Guidelines Group (GMSG) currently supports nine individual industry working groups focused on developing standards and guidelines for the mining industry. In 2013 the GMSG established the Industrial Comminution Efficiency (ICE) working group to develop freely available guidelines for plant operators to quantify the operating efficiency of industrial comminution circuits. This initiative has engaged a diverse group of representatives from mining companies, equipment vendors, consultants and metallurgical laboratories with vast experience and capabilities in the field of comminution. The GMSG has issued the first two guidelines from the ICE working group in 2015–2016, with the third guideline having completed the approvals process and being in the final stages of editing ahead of release later in 2016.Two of the ICE guidelines present methods to quantify comminution circuit efficiency, and a complementary guideline describes best practice methods to collect the necessary samples and data to furnish these assessments. Collectively the guidelines cover sampling, survey data collection, laboratory testing procedures and calculation processes to allow the user to generate a relative circuit efficiency factor for the comminution circuit at the time of survey. The reference energy consumption is calculated considering the measured F80, P80 and ore strength at the time of survey, using either or both of the Bond or Morrell methods presented in GMSG guidelines dedicated to each method. The guidelines consequently provide the end user with practical tools to perform circuit efficiency analysis and to readily quantify the impact of optimisation efforts.This paper presents the content of the three ICE guidelines and describes their intended application.Citation:Giblett, A and Daniel, M, 2016. Global Mining Standards and Guidelines for Determining Comminution Circuit Efficiency, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 3–8 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By Thomas E. Ricketts

Occidental Oil Shale, Inc. constructed two commercial-sized modified in situ (MIS) retorts, Retorts 7 and 8, at its Logan Wash Oil Shale Mine in February and April 1981, respectively. One of the primary objectives of this two-retort program was to examine large-scale blasting reproducibility for commercial-sized retorts. The blast design used 545 blastholes and 550,000 pounds of explosive in ANFO equivalent per retort. Each retort was blasted using millisecond delay blasting caps tied into a single round. The blasts resulted in rubble beds very close to one another and to predicted results obtained using newly developed limited void blasting technology. The heights of the remaining void rooms over the beds after blasting were within 0.3 feet of one another. This excellent reproducibility is brought into true perspective when compared to the scale of the rubble beds which were 230 feet high with volumes of over six million cubic feet each.

Jan 1, 1984

By T. Hart

Nuclear gauging is used world-wide in almost every industry. From mining and ore-grading to finished product, the metallurgical industry is one of the biggest users of nuclear sensors for inventory, process control, and quality assurance. This paper will discuss the basic theory of gamma transmission gauging techniques found useful in mining, milling and metal production. Techniques to be discussed are gamma transmission for level and density. A major new technique will also be discussed. This technique is called gamma backscatter. The uniqueness of this technology, how to apply and the differences between transmission and backscatter will be accentuated.

Jan 1, 2011

This paper describes basic parameters, such as surface forces and film elasticity, affecting the stability of foams (two-phase froths). We used the thin film pressure balance (TFPB) technique to measure the surface forces in foam films stabilized with various frothers such as pentanol, octanol, methyl isobutyl carbinol (MIBC), and polypropylene glycol (PPG). The results were compared with the foam stabilities measured experimentally and the film elasticities calculated using a new model developed by Wang and Yoon (2006). It was found that at low electrolyte (NaCI) concentrations foam stability is controlled by both film elasticity and surface forces (or disjoining pressure), the relative contributions from each changing with frother type and concentration. Further, the kinetics of film thinning was studied at a high electrolyte concentration. The results obtained in the present work showed that the major role of a frother is to decrease the hydrophobic force rather than to increase the film elasticity. This conclusion is drawn from the observation that at the typical frother (MIBC) concentrations employed in flotation, frother additions cause sharp decreases in hydrophobic force while causing relatively little changes in film elasticity.

Jan 1, 2006

By W. W. Weller

Thermodynamic values for scandium and its compounds are very sparse. This is evident upon examination of any of the commonly used compilations of thermodynamic data. For example, National Bureau of Standards Circular 5004 lists only four heat of formation values, two free energy of formation values, and four heat-capacity values for scandium compounds. The entropy of crystalline scandium is one of the most fundamental values that has been lacking. This Bureau of Mines paper reports heat-capacity data for scandium metal in the temperature range from 50° to 298° K., together with the entropy value at 298.15° K. derived from these data through application of the third law of thermodynamics.

Jan 1, 1962

By Kathleen A. Altman

"This paper supplements the information provided annually at the Canadian Mineral Processors Operators Conference regarding the education of Mineral Processors in Canada. The purpose of the paper is to provide information regarding the engineering accreditation process in the United States and the universities that offer programs in Mineral Processing and Extractive Metallurgy in the U.S.There is a critical shortage of trained Mineral Processors and Mining Engineers world wide. The Society for Mining, Metallurgy and Exploration (SME) formed a task force to evaluate the national needs for trained engineers and to track the number of engineers who graduate from U.S. universities each year. The statistical information for Mining Engineers is well-developed. The current effort is to assemble similar information regarding students who graduate with expertise in Extractive Metallurgy and Mineral Processing as well as to explore the limitations of the accreditation system in the United States and its impact on the education of Mineral Processors. The long-term objective is to develop a data base regarding Mineral Processing programs and Mineral Processing graduates that is as complete as the one that has been maintained by the Canadian Mineral Processors.INTRODUCTIONIn the United States engineering curricula are accredited by ABET, which was formerly known as the Accreditation Board for Engineering and Technology. The objective of ABET accreditation is to ensure that educational programs in applied science, computing, engineering and technology meet quality standards set in conjunction with the professional organizations that represent professionals in the industries which hire students graduating from those educational programs. For example, the Society for Mining, Metallurgy and Exploration (SME) is the lead society for accrediting Mining Engineering programs in the U.S. For Materials Science and Metallurgical Engineering programs, the lead society is The Mineral, Metals and Materials Society (TMS). SME is a cooperating society for accrediting Metallurgical Engineering programs. Cooperating societies for the accreditation of Materials Engineering include the National Institute of Ceramic Engineers (NICE), the American Institute of Chemical Engineers (AIChE) and the American Society of Mechanical Engineers (ASME)."

Jan 1, 2008

By Li Xi

This paper describes how a back-propagation neural network is built for predicting the properties of engineering materials from their other properties, compositions or processes. A predicted result of the impact toughness of a 12Cr-2Ni-1.5Mo stainless steel from its tempering temperature is presented. Furthermore, the combination of this neural network for prediction is able to supplement the unpredictability of the expert system outside its domain of expertise. An integrated system may perform more intelligently and solve more complex problems as well as human expert, in some case even better.

Jan 1, 1992

By Lawrence W. Gubbe

Air blast associated with detonation of explosives in mining, construction or military applications is often responsible for complaints by people who live or work in the vicinity of the activity. Most often, the complaints are based on the perception that vibration caused by the airblast damaged one or more residential buildings that may be located within several hundred feet or several miles from the blast site. The potential for airblast to cause damage is related to the amplitude and frequency of the airblast overpressure wave at the receptor. Amplitude and frequency of the overpressure wave are, in turn, dependent upon the type and amount of explosive detonated; the degree of confinement; the distance the wave travels; the topography between the blast site and the receptor; and, atmospheric conditions. It is well known that, as the result of atmospheric focusing, the amplitude of airblast overpressure that exists relatively far from the blast site may be substantially higher than the amplitude associated with the attenuated wave in an isotropic atmosphere. Two methods are available to predict baseline overpressures 1) the Sandia Laboratories, Atomic Energy Commission method as extended by the Naval Ordinance Laboratory (NOL method) and the Ballistic Research Laboratory method (BRL method). These methods are developed by different techniques, are based on different idealized atmospheres and predict widely different results. The amplification factor applied to account for the effect of focusing must be consistent with the method used to predict the baseline overpressure. Theoretically, the amplitude of the overpressure at distances several miles from the blast site could be more than 25 to 100 times the amplitude of the attenuated wave predicted by the BRL method. However, based on comparisons with measured overpressure data is probably less than approximately 3 times the amplitude of the attenuated wave as predicted by the NOL method. This paper is based on research conducted as part of investigations of airblast damage complaints associated with an accidental explosion near Eveleth, Minnesota and with the disposal of military explosives by detonation at the Sierra Army Depot near Herlong, California. The techniques available for estimating the airblast overpressure that might be generated at various distances from the blast site and criteria for evaluating the potential for damage are examined.

Jan 1, 2004

By Jack A. Caldwell

"This paper describes the nature of stage curves and the ways in which they have been used to study the construction sequencing of tailings impoundments. They provide a simple graphical method of representing the main aspects of an impoundment, studying the effects of different impoundment geometries, and predicting and controlling impoundment operations.IntroductionThe designer o f a tailings impoundment must, at all stages of design, examine the relations hip between the volume o r tones of tailings that will be deposited at the impoundment, the height to which the tailings will rise in a given time and that rate at which the various parts of an impoundment will be constructed. The operator, if he is to keep proper control of this impoundment, must be able to examine the effect of different deposit ion rates at the impoundment, and the consequences of placing more or less tailings at different parts of the impoundment. The operator must be able to see at a glance just how much higher an impoundment will be at the end o f the following yea r of deposition, and this he must be able to do in order to formulate his annual construction and operating plans.Stage curves are the best way o f modeling an impoundment. The simple impoundment model represented by the stage curves enables the designer and operator visually to examine the relationships between the various factors, such as impoundment volume, deposition rat e and construction rate, that dictate the essential features o f impoundment design and operation.A design model for a tailings impoundment may be formulated as in Figure 1. This involves the site selection process, the definition o f a geotechnical model, a water balance model and a height-capacity-production model."

Jan 1, 1983

By Player R. L

Measurements of the rate of PbO reduction from high lead metallurgical slags were made under laboratory conditions using graphite, a CO-50%CO2 gas mixture and metallic iron as reductants. The results show a transition in rate-controlling step at low PbO contents (i.e. 6 wt.% PbO). At medium to high PbO contents in the slag, the reduction rate was found to be strongly affected by the slag chemistry, temperature and reductant type. The effect of stirring and hence mass transfer in the slag phase on the reduction rate of PbO was found to be insignificant at medium-high PbO contents. Attention is drawn to the importance of chemically controlled reaction rates at the slag-gas interface. Parallels between these results and test work on a 5 tph scale have been briefly drawn.

Jan 1, 1989

Flotation of Smithsonite by Using Siloxane Cationic Surfactants as Collectors

Sep 13, 2010

By Caroline Gomes de Oliveira

Os impactos causados pela exploração dos recursos naturais pelo homem geram uma crescente inquietação em relação futuro do planeta a longo prazo. Assim, as fibras naturais vegetais ganham destaque como material de reforço por suas boas propriedades mecânicas, baixo custo e por serem biodegradáveis. Umas das fibras que mais ganhou destaque nas últimas décadas é a fibra de rami, objeto de inúmeros estudos. Neste trabalho, analisou-se o efeitodo tecido produzido com a fibra de rami como reforço para a matriz epóxi sob esforços de impacto Charpy e Izod. A metodologia utilizada foi a produção de placas laminadas sob afeito de vácuo. Os resultados mostram notável diferença na resistência ao impacto do compósito comparado à matriz sem reforço.

Oct 30, 2017

By R. F. Favreau, Patrice Favreau, Dennis Mahan

Cast blasting is becoming more and more popular, not only in coal mines but also in other operations which require excavation of an upper layer of waste rock to uncover temporarily and excavate a layer of ore, which may for example be material for the fertilizer industry.

Jan 1, 2014

By Luiz Carlos Teixeira Brandão

O Alto-Forno 3 da Usiminas em Ipatinga, que atualmente está na sua quarta campanha, apresenta 30 ventaneiras. Nesta campanha houve alguns eventos de arrombamento e avermelhamento dos algaravizes. A causa destas ocorrências são obstruções das frentes de combustão das ventaneiras, gerando diversos transtornos operacionais. A fim de se evitar novos fatos semelhantes foram desenvolvidos alguns sistemas de monitoramento das frentes de combustão. Dentre os sistemas desenvolvidos se destacam o diferencial de pressão do conjunto de sopro; e, o controle da temperatura do conjunto de sopro. Os sistemas desenvolvidos permitiram maior confiabilidade nas ações imediatas dos operadores em anormalidades na zona de combustão com consequente ganho em desempenho operacional do alto-forno.

Aug 1, 2018

By Luis G. Bergh

Today, large size mechanical flotation cells of 100 to 300 m3 are used in rougher operation in different flotation industrial plants, in Chile and worldwide. However, in spite of the advances in fundamental research and the notable growing in equipment size, with more complete instrumentation systems, there are still a lack of reliable data for industrial flotation modeling and simulation to advance in better control systems design. In this work, a model of a rougher flotation circuit, based on operating variables and parameters fitted from industrial data, obtained in some previous work, is used to develop a set of logic rules in order to aid operating decisions. The simulator was first used to sensitize the effect of changing the froth depth profile on target variables, and then to find out the best profile to reject common disturbances coming into the plant. The flotation circuit simulator was redesigned to incorporate an expert system following the proposed control algorithm. Several tests were performed to evaluate the control responses to different correlated series of input variables, such as feed grade, tonnage, particle size distribution, and solid percentage. Control alternatives are discussed based on the circuit simulator. Keywords: modeling, industrial data, flotation control, mineral processing.

Sep 1, 2012

By G. T. Krempasky

In an attempt to develop a suitable precast concrete support for underground use, two different models (1955 and 1958) of a five-piece concrete set were designed, fabricated, and tested under adverse loading conditions. Model 1955 was designed to withstand an ultimate, uniformly distributed, vertical load equivalent to what a three-piece, 12- by 12-inch wood set of intermediate-grade Douglas fir would withstand. A design figure of 138,000 pounds for the vertical load was used on both the 1955 and 1958 models. In addition, the 1958 model was designed to withstand a uniform horizontal load of 7,000 pounds per foot and additional concentrated-point loading. The step- by-step design of each model is presented in the appendixes. A series of five destruction tests was conducted underground on the 1955 model, and results of the tests showed that the type and method of blocking were of major significance.

Jan 1, 1963

By N. Campbell

"The fault under consideration follows a northerly trend past the west; side of the original settlement of Yell ow knife; which is situated 600 miles; north of Edmonton and 400 miles from the Northern Alberta Railway; terminus at Waterways; Alberta. The mining properties chiefly concerned; include the southern part of the Giant claims; on the east side of the fault; and the Con-Rycon-Demelt claims; on the west side 3 1/2 miles to the south.; Geological data were also obtained from the eastern part of the A.Y.E.; property; which lies south of the Giant claims; and from the Negus; Meg; Yellorex; and Kam properties; which are south and southeast of the ConRycon-; Demelt claims (see Frontispiece; also Fig. 5).Recognition of the major faults in the Yellowknife Bay area, including the West Bay fault, which appears to be the greatest, resulted from the work of A. W. Jolliffe (formerly of the Geological Survey of Canada) in 1935 and subsequent years. It has been stated with little exaggeration that these faults rank with the largest known steeply dipping dislocations of the earth's crust.In the winter of 1939, a mineralized shear zone named the 'Creek vein' was found on the Giant property. It was noted that the space relationship between this shear zone and a body of quartz-feldspar porphyry is roughly the same as that between the Con C-4 shear zone and a body of acid flows lying north of the Con property. Coupling this relationship with the assumption that the movement along the fault is dominantly horizontal, it was postulated that the Giant shear zone represented the faulted extension of the Con C-4 shear zone.As geological information became more extensive, certain weaknesses in this concept became apparent, and when spectacular orebodies were discovered on the Giant property in 1944 the question of possible faulted extensions became an important consideration. Consequently, in the spring of 1944, an extended investigation was undertaken, the results of which are embodied in this paper."

Jan 1, 1954

By Evandro Moraes da Gama

A aglomeração a frio de minérios, rejeitos de mineração, resíduos sólidos, combustíveis, fertilizantes, produtos químicos, farelos de alimentação animal, etc. é um tema de grande relevância para o setor industrial dentro do contexto de crescimento sustentável. Neste trabalho é feita uma descrição da moderna planta piloto de aglomeração a frio de finos de minérios de ferro empregando o disco pelotizador SC-1000 (Haver). Essa unidade piloto pertence ao Centro de Sustentabilidade da UFMG, que está localizado na cidade de Pedro Leopoldo (Minas Gerais, Brasil). Esse tipo de equipamento difere dos discos tradicionais no mercado por agir de forma dinâmica na formação da pelota crua durante o processo de aglomeração a frio. A tecnologia Scarabeus permite o ajuste automático da altura da borda do disco, assim como da inclinação e da velocidade de rotação, mesmo durante a etapa de operação. É também feita uma abordagem sobre a inovadora tecnologia Scarabaeus de discos pelotizadores para plantas industriais de aglomeração de minérios. Ademais, são apresentadas as principais linhas de pesquisa referentes a aglomeração a frio de materiais finos.

Aug 1, 2018