Search Documents

By Gheorghe Vieru

Security and safety due to environmental impact as well as the radiological consequences during the uranium mining operations, tailings management, uranium processing, disposal of waste in conventional landfill sites are matters of great importance. The Uranium National Company (CNU) from Romania is responsible for all aspects belonging to the management of the entire Romanian uranium industry- the uranium ore extraction, transport and processing of uranium ore, concentrates processing, as well as disposal of sterile ore and waste. The paper will presents specific safety problems related to the identification and evaluation of potential environmental risks, as well as possible radiological consequences associated with the disposal of sterile and the uranium processing waste resulting from processing of the uranium ore. Computer codes will be used, such as IAEA INTERTRAN II and RADTRAN 5. It is also to be noted that this paper considers the main results of the scientific research carried out by the main author as CSI (Chief Scientific Investigator) for Romanian Research Contract on NORM concluded with IAEA Vienna.

Aug 1, 2010

By Jerome Strauss

IN his review of developments in 1943, Gilbert Seil, Chairman of this Committee on Reduction of the Ferroalloy Ores, tabulated the consumption of the alloying metals in relation to the steel production of that year. In the year just closed the approximate tonnage was of the same order, differing only to a minor degree or suffering some correction with more precise figuses available, as indicated in the following estimates: Consumption Metals in Tons Steel 92,000,000* Manganese 700,000 Silicon 200,000 Chromium 200,000 Nickel 75,000 Molybdenum 20,000 Tungsten 8,000 Vanadium 1,700 Titanium 1.600 Boron 10 `Production figure. The technologic studies instituted during 1942 and carried forward with such great vigor during 1943 continued into 1944 although in some instances were brought to a close either by completion of the specific development

Jan 1, 1945

By D. Sharma, A. K. Singh, R. Singh, P. K. Mandal, M. Sarkar

"This paper deals with the stability investigations carried out at the XIVth seam of Jitpur colliery. The study was conducted to investigate the possible causes of roof cavity formation and face spalling at the middle slice face of block-3 longwall panel and to suggest remedial measures. The instrumentation and monitoring work was carried out in the panel over a period of nine months. On the basis of observations, it was found that if the maximum face span was reduced from the existing 4.8 m to 3.6 m, and if the face time schedule cycle was reduced from a maximum of 37 days to about 18 days, this problem could be eliminated. The recommendations of CMRI have been implemented in the middle slice face of block-4 panel with success. IntroductionModerate to steeply dipping, undisturbed seams of uniform thickness are worked by way of inclined slicing parallel to walls. In this method, the seams are treated as a combination of several moderately thick seams dipping parallel to roof and floor. Numerous variations of multislice mining have been used worldwide to get high coal recovery under local conditions of geology, subsidence control, proness to spontaneous combustion, statutes and economics. Multislice mining can proceed either downward descending from the roof or upward ascending from the floor. Ascending methods require backfill behind the working face to provide a base for the next slice. It is also adopted for surface protection against subsidence or mining under a massive roof. This paper presents a scientific study conducted in Jitpur colliery, IISCO where a 9 m thick seam is mined in three slices in ascending order with stowing."

Jan 1, 2002

Jan 1, 1999

By B Murphy

Seeking to reduce the likelihood of uncontrolled personnel entry into the operating footprint of a dragline, Coronado Global Resources initiated a review of proximity detection systems currently available and equipment interactions in and around dragline operational areas. At the time of the assessment, there were no established personnel proximity detection systems in compliance with functional safety standards for large machinery in Australia. Our primary objective was to guarantee a functionally safe outcome, particularly by implementing a performance-level-rated system in accordance with AS4024 (Safety of Machinery series of Australian Standards). Applying appropriate detection technologies, the goal was to reduce the residual operating risk for machine-to-machine and machine-to-personnel interactions. A comprehensive analysis of available or in-development technologies was conducted, and a layered approach (demonstrated in Figure 1) was adopted to achieve the desired risk reduction by segregating the sensing zones into distinct areas using diverse and disparate technologies consisting of radar (short); light detection and ranging (LiDAR) (medium); and optical (long). To address the potential limitations of each technology, overlapping layered sensing zones were designed. With LIDAR and optical using two distinct artificial intelligence (AI) systems to classify detections, these were specifically trained to handle the unique environments of a mining operation.

Sep 1, 2024

By Thomas M. Tharp, Mark A. Travers

A new method is presented for precracking three-point bending specimens for fracture toughness testing. A notched specimen of rectangular cross section is placed on a flat loading platen, with paper between specimen and platen. The specimen is loaded from above through a roller placed directly over the crack. The thin, high compliance joint between specimen and platen causes a distributed load on the bottom of the specimen. This results in bending at the cracked section and crack initiation at the notch tip. Since the joint is thin, its stiffness increases rapidly with deflection and crack propagation in the specimen generally remains stable and controllable. Fracture toughness KIC in a sandstone directly overlying the No. V coal was measured to be 0.27 MPa m 1/2. Even for cracks 1 cm long this value of KIC results in substantially lower effective tensile strength (modulus of rupture) in roof beams than is expected from intact rock strength.

Jan 1, 1986

By Imane Benhamed, Jaouher Diouani, Laurent Cassayre, Florent Bourgeois, Carine Julcour-Lebigue, Université de Carthage

The attrition-leaching process aims at improving leaching performance when formation of passivation layers at the surface of leached particles is a severe limiting factor, as discussed recently by Julcour and coworkers (Julcour et al., 2015). This paper proposes a geochemistry-based modelling scheme for deriving the window of possible operating conditions for the attrition-leaching process to match the properties of the processed ore. The rationale is that the attrition-leaching process maintains the surface of reacting particles in an unpassivated state by continuous mechanical removal of surface leach layers, so that the process reactions can be modelled from thermodynamic equilibria throughout the duration of the process. The strength of the proposed modelling approach is that it bridges the gap between the properties of the ore and the process operating conditions. The present paper exemplifies the proposed process modelling route for derivation of the attrition-leaching process operating conditions in the context of the leaching of silicate ores, matching model predictions against controlled laboratory experiments. It is shown how thermodynamic modelling, when used in conjunction with a solid knowledge of the phases present in the system, can assist with deciding upon suitable process operating conditions. As an example, this firstprinciple modelling approach predicted that steel grinding medium would be converted into siderite (FeCO3) under a wide range of operating conditions, which led to questioning this initial choice of grinding medium for the attrition-leaching process under mineral carbonation conditions. It is emphasised that the same approach could be applied to ores of greater economic significance.

Jan 1, 2016

By G. R. Morin, A. R. Leggett

"In 2010, closure of the Kidd metallurgical plants along with structural changes to the historical ratios of payable metals led to a review of the operating targets at the Kidd concentrator. Previous operating data indicated that there was potential for significant revenue improvements by lowering the copper concentrate grade. An extended plant trial was carried out in 2011 to quantify the revenue impact of lowering the copper concentrate grade from 27% to 25% Cu, as well as identifying the lower practical grade limit. Analysis of plant trial results indicated that the process change increased net concentrate revenue by $2 M to $3 M per year at current metal prices. Increased revenue was primarily associated with higher silver recovery to the copper concentrate while the marginally improved copper recovery was essentially offset by increased zinc losses and concentrate treatment and freight charges.Details of the plant test work results are discussed in this paper along with the financial analysis of the revenue improvements. Key areas covered are major revenue components of the concentrate contracts, validation of revenue improvements through plant testing and sensitivity of the improvements to market and plant variables.INTRODUCTIONThe Xstrata Copper Kidd concentrator commenced operations in 1966 treating ore from the nearby Kidd volcanogenic massive sulphide deposit in Timmins, Ontario (Thompson, Amsden, & Chapman, 1978). Over the years, up to four separate grinding-flotation divisions were in operation with throughput rates peaking at 4.5 million tonnes per year of ore in the mid 1980’s (Kelebek & Francis, 1998). As the mine production decreased and grinding throughput increased operations were gradually cut back and since 1998 two grinding-flotation divisions have been in operation treating Kidd mine ore. One of the idled divisions has been intermittently used for custom milling operations, most recently the Ni/Cu Montcalm deposit, which was milled from 2004 to 2009. Current budget throughput rates, limited by mine production, are 2.4 million tonnes per year of ore grading 1.7% Cu, 4.3% Zn and 55 g/mt Ag. Concentrate production rates are 150,000 tonnes per year of copper concentrate and 155,000 tonnes per year of zinc concentrate. The Kidd mine is the deepest base metal mine in the world with mining operations down to 9600 ft.In 2010 the copper and zinc plants at the Kidd metallurgical site, which previously treated the concentrate production from the Kidd concentrator, ceased operation due to a variety of economic and market factors. Following the metallurgical plant closures the Kidd concentrator products were shipped off site for treatment. The majority of the copper concentrate is now processed at the Xstrata Copper Horne smelter in Rouyn-Noranda, Quebec with the majority of the zinc concentrate processed at Canadian Electrolytic Zinc Ltd. in Valleyfield, Quebec."

Jan 1, 2013

By Kazimierz St. Sztaba

"Mineral processing – the first technological stage of utilization of mineral – has a very long history. In particular, it revealed and reveals the continuous development and perfection of technological operations and process organization, comprising not only new design solutions and exploitation procedures but also, for example, perfected systems of control and automation as well as methods of process description and result evaluation. During the recent decades the attitude to mineral raw materials was clearly changed, both to the primary ones, i.e. minerals, and to the secondary ones, such as side products and waste, formerly considered useless and at present more commonly used. This results both from the appearance and growth of demand for more and more numerous components of mineral raw materials and also from the necessity of protection of natural resources, constituting the integral part of the system of sustained development of society.These circumstances, and especially the requirements concerning gaining some components which cannot be separated by means of “classical” (used for many years) technological processing operations and aiming at increasing the technological procedures, evoked the necessity of using new technological solutions, applying other basic operations, also the ones characteristic so far for other processing technologies, i.e. chemical, biotechnological and others.These development tendencies, in general commonly perceived, allow us to formulate an opinion that the former state of tasks and processes of mineral processing is being transformed into a qualitatively new form. It can be assumed that this process was signaled by a situation in which, due to the growing role of technological operations based on physicochemical phenomena (flotation and others), magnetic and electrical ones, etc., one should have observed that the former term of “mechanical processing” became inadequate for the real content of the notion determining the discussed stage of mineral utilization, so the adjective “mechanical” disappeared in most languages."

Jan 1, 2003

By Sherif Elfass, Gary Norris

Bi-directional load testing of drilled shafts has been widely adopted as a means to evaluate their load carrying capacity. However, in order to reach failure, most of these tests are carried out on sacrificial shafts using expensive sacrificial elements such as hydraulic jacks. A proposed low-cost bi-directional testing technique is discussed. It mechanically loads the end bearing soil below a drilled shaft, against its side shear resistance. The technique was originally established as an alternative to post-grouting to reliably account for the forfeited end bearing resistance. However, since it loads the shaft in a manner similar to conventional bi-directional tests, it can be used to not only load test sacrificial shafts, but production shafts as well. Furthermore, unlike conventional bi-directional load tests, the load is applied through surface jacks. These jacks, along with other load test components, are movable and can be reused to load test all the shafts of the project thus presenting an economic benefit. The concept of this technique has received favorable feedback from a few consulted departments of transportation, and while promising, has not been field tested to date. A U.S. patent was issued for the tip loading module and the loading technique described.

Sep 8, 2021

By E. R. Phelps

It is very seldom that a completely new project is initiated. Most projects consist of a new and different combination of proven techniques or a combination of proven and new techniques. The theme of my discussion today falls in the second category. Proven methods of water transportation and proven methods of bulk material handling were combined with some new techniques which resulted in a new market for the coal industry and a cheaper fuel supply for the power industry. In this respect I refer to the water transportation of coal from the West Kentucky coal fields to coal burning power plants on the west coast of Florida. Peabody Coal Company, Florida Power Company, Gulf Coast Transit, and Mid-South Towing combined their individual requirements and "know how' to make this project possible. I feel the results speak for themselves since it proves that coal can be mined in the West Kentucky coal fields, transported some 1,200 miles by river barge and some 450 miles by ocean going barges, be delivered to power plants on the west coast of Florida and still meet the competitive prices of gas and residual oil. The unique parts of this project concerns the storage and trans loading facilities for coal from river equipment to ocean equipment near New Orleans; the return haul of phosphate and it's trans loading from ocean to river equipment at the same facility and the use of large ocean going barges. In detail it works as follows: Coal is mined in West Kentucky and loaded into 1,500 ton river barges on the Green River. It is then transported some 100 miles to the mouth of the Green on the Ohio River, then 200 miles down the Ohio to it's convergence with the Mississippi, and then 900 miles down the Mississippi to the trans loading facility some 40 miles South of New Orleans. There it is transferred from the 1,500 ton river barges to 18,000 ton ocean going barges and hauled some 450 miles across the Gulf of Mexico to the Gannon Station of Tampa Electric at Tampa entailing a total haul of approximately 1,650 miles.

Jan 1, 1966

By J. K. Whyatt

Researchers at the U.S. Bureau of Mines have been exploring recent advances in the use of strain-softening constitutive laws that approximate shear fracturing. The purpose of these tests is to investigate shear-fracture-related rock bursts in hard-rock mines. The capabilities and remaining problems in the use of strain-softening laws in finite-element, distinct-element, and finite-difference methods are reviewed. Performance of the finite-difference implementation of strain softening is compared to classic experimental results and observations of rock mass behavior in the Coeur d'Alene Mining District of northern Idaho. The results show promise for developing methods to identify the general location and orientation of shear fractures and their sequence of occurrence, but such methods cannot be relied upon to quantify post-fracture loads or displacements accurately. Uncertainty over the amount of energy consumed by failing rock and the dependency of energy consumption on model mesh definition prevent direct application of the results to analyses of rock bursts.

Jan 1, 2010

Choosing the right valve for corrosive, abrasive slurry applications requires exacting analysis and a comprehensive understanding of the complete slurry process. Within the realm of flow control in abrasive and corrosive slurry applications, there is no room for a one-size-fits-all approach. To ensure minimal maintenance, maximum uptime and the lowest overall cost of ownership, the slurry processing toolbox must contain countless alloy and elastomeric pairings ? each carefully targeted to the particular process medium and conditions. This materials selection process is best tackled by turning to expert slurry application engineers and valve product managers who work closely with customers to specify the optimal valve for the given parameters. ?When plant operators and design engineers apply conventional valves in abrasive applications or use metal seated valves or simply apply the wrong valve for a particular flow control situation, it typically leads to rapid valve failure, the potential for hazardous leakage, unexpected shutdowns and costly downtime,? said Cal Cobb, valve products manager for Weir Minerals North America, manufacturer of Isogate slurry valves for service in mining, minerals processing and metallurgical environments.

Jan 1, 2011

By G Zhang, I Glacken

Multiple indicator kriging (MIK) has been used in the minerals industry for some decades. As one of the non-linear estimation methodologies, MIK has advantages related to resolving multiple or mixed populations, high variability data and strongly skewed distributions. Applying the MIK methodology requires a lot more effort when compared to other non-linear methodologies, for example localised uniform conditioning. This is due not only to the variogram modelling for multiple indicators, but the validation is also very important because the panel model is fundamental for follow-up work, including the generation of recoverable resources at the local or SMU scale. Apart from this, only a few reported case studies of MIK have documented post-processing of the estimated modelled distribution, representing the probability distribution at point scale at un-sampled locations. The MIK post processing should include the change of support from the point scale to the panel scale, and then the extraction of quantile values from the panel conditional cumulative distribution function (CCDF) for localisation of grades into the SMUs within each panel, based on a ranking estimate marking the SMUs from high to low. In this paper, we present a case study on a gold deposit with the MIK method with full-post processing implemented for recoverable resources. The MIK point estimate was carried out with an indirect lognormal change of support from point to panel scale, and localisation was done with a custom script. The localised uniform conditioning (LUC) method was also applied for comparison purposes. The comparison shows that MIK has advantages compared to LUC when comes to capturing the high-grades, especially when mixed or varying anisotropy is present within the mineralisation.

May 24, 2023

By Paul D. Bybee

The Freeport Sulphur Company operates four sulphur mines in the coastal marsh area-03 South Louisiana. Employing the Frasch process of mining, approximately 13-million gallons of water per day is heated to a mining temperature of 325°F and is injected into the sulphur bearing formations of the four mines. A volume of cold waste water, roughly equal to the Input, is removed from the formations and presents a disposal problem. Two additional mines are currently being developed and will increase the disposal volume by an additional 5-million gallons per day. Although these properties are in a relatively small area, geographically speaking, as shown in Figure 1, they each represent a separate disposal problem with the treatment methods designed for the individual mine.

Jan 1, 1959

By C. L. Karr

Researchers at the University of Alabama are investigating artificial intelligence based computer models of mineral processing systems. Two approaches have been found to be particularly effective in developing data-driven computer models. The first approach employs neural networks which are computational paradigms based on the mechanics of the human brain. They are able to extract the basic relationships between input and output variables from large data sets. The second approach combines fuzzy mathematics with genetic algorithms to produce an adaptive modeling system. Fuzzy mathematics provide computers with the capability of manipulating abstract concepts like those which humans use so effectively in decision making. Genetic algorithms are search algorithms that mimic evolutionary processes apparent in nature. Together, these two techniques can be used to produce an effective modeling system. In this paper, the two approaches to modeling are compared and contrasted with respect to accuracy and computational time while used to model three mineral processing systems: (1) a grinding circuit, (2) a hydrocyclone separator, and (3) a flotation circuit.

Jan 1, 1997

By W. C. Foshee

The large volume of water used in coal preparation plants makes water recycling a necessity. Economical cleaning of dirty water usually requires flocculation with an efficient organic polyelectrolyte. This paper discusses identification of optimum flocculant systems. Supporting laboratory data with on-site tests and full scale field trials supplies information necessary for matching the polymer to the plant.

Jan 1, 1979

By D. Z. Wang

A red copper plate, discovered in the ruins of Dachengshan in Hebei province, was recognized as a forged one rather than a cast one, which means it was probably made from natural copper during the Longshan Culture period (2200~2208 BC) in the Chinese history. The copperware, found in the Niangniang Tai relics in Wuwei city, Gansu province, contains 99.6% copper and 0.4% Sn, Pb, Sb and Ni, which was guessed to be made during the Qijia Culture about 2000~ 1900 BC in the Chinese history in the late Neolithic before Shang dynasty. This shows that Chinese ancestors were able to distinguish, sort and use some native metals and minerals more than 4000 years ago.

Jan 1, 2014

By C. Fortin

ABSTRACT The subject of gold flotation has been reviewed extensively. Most of these reviews focus on the theories of gold flotation and the physical and chemical effects that may impact the efficacy of the gold flotation process. The current status of gold flotation chemistry as it is being applied in industry has not been widely addressed. This paper reviews current gold flotation practice and research advancements and discusses how these applications tie in with the current understanding of gold flotation chemistry. Survey results from worldwide gold flotation operations are analyzed. Potential future areas of gold flotation research are highlighted.

Jan 1, 2013

By Daniel Hiroshi Taira Anese

O objetivo desse trabalho consiste no estudo do grau de sensitização do aço UNS S31803 envelhecido a 700ºC por ensaios de reativação potenciodinâmica de duplo loop (DL-EPR). Para isso corpos de prova do aço em estudo foram solubilizados a 1175ºC e envelhecidos a 700ºC em tempos entre 10 min e 360 h. Corpos de prova metalográficos foram utilizados para caracterização microestrutural que foi realizada por meio de técnicas de estereologia quantitativa a partir de imagens de elétrons retroespalhados e análises magnéticas usando o ferritoscópio. Os ensaios DL-EPR foram conduzidos em solução 2M H2SO4 + 0,5M NaCl + 0,01M KSCN à 30ºC em amostras polidas. Observou-se que o comportamento eletroquímico do aço UNS S31803 possui forte influência da microestrutura, já que o grau de sensitização (GS) aumenta com o aumento do tempo de envelhecimento, devido à formação de fases intermetálicas que empobrecem as regiões adjacentes em Cr e Mo.

Aug 7, 2018