Search Documents

By Rafael Paini Pavlak

A trefilação a frio para produção de barras de aço é realizada em função da sua precisão dimensional e modificação das propriedades mecânicas do material. O processo consiste na conformação de um fio-máquina que, guiado por um puxador, passa através de uma ferramenta (fieira de trefilação). Tal procedimento irá inserir tensões internas na barra chamadas tensões residuais, as quais, dependendo da sua distribuição e intensidade, podem causar distorções do produto final e possivelmente seu descarte. A fim de prever o comportamento destas tensões foram desenvolvidas simulações tridimensionais no software DeformTM. Este trabalho teve por objetivo explorar os efeitos do desalinhamento angular da fieira combinado com uma heterogeneidade na distribuição do atrito, avaliando a influência na distribuição de tensões residuais na barra trefilada. Observou-se certa influência na distribuição das tensões finais, atingindo diferenças em torno de 300MPa entre superfícies, o que caracteriza um potencial de distorções no produto final.

Aug 8, 2018

By Alexandre de Aparecida Morais

No processo de lingotamento contínuo a secagem e o pré-aquecimento do refratário do distribuidor são de fundamental importância. Estes são realizados visando: reduzir a perda de calor do aço líquido, reduzir as bolhas nas primeiras placas, evitar respingos de aço (reações) ocasionados pela umidade e prevenir a degradação refratário por choque térmico. Para aços planos, os sistemas para promover a secagem e pré-aquecimento podem ser do tipo a "quente" (mais usual) ou a "frio". É denominado "partida a quente" quando se realiza a secagem e o pré-aquecimento; e de “partida a frio”, quando apenas a secagem é realizada. Têm-se como características distintas entre os processos: - A Quente: maior consumo de gás; forte degradação do refratário; temperatura de trabalho do distribuidor mais elevada, deteriorando as condições do ambiente; - A Frio: menor consumo de gás; redução da degradação do refratário; no entanto, exige um controle rigoroso da curva de secagem, o que implica maior investimento inicial no equipamento de secagem. Em 2002, após uma análise de viabilidades a ArcelorMittal Tubarão implementou o sistema de frio. Este artigo mostra a evolução deste sistema após a sua implementação, analisando a correlação com defeitos, a implementação de melhorias e os ganhos obtidos.

Jul 30, 2018

By Lumena Glória de Souza Nunes

Objetivo deste trabalho foi simular o processo de deformação plástica severa, mais especificadamente o processo de colaminação acumulativa (Accumulative Roll-Bonding-ARB) em aço baixo carbono, por ensaio de torção a morno. Os corpos de prova foram inicialmente recozidos à 900ºC por 5 min e resfriados dentro do forno com potência desligada. Realizou-se o ensaio de torção à 500ºC aplicando cinco passes de deformação de 0,8, totalizando uma deformação verdadeira de 4, à uma taxa de deformação de 0,1s-1, bem como deformações intermediárias de 0,8; 1,6; 2,4 e 3,2. Para verificar a influencia da temperatura no processo, realizou-se o ensaio também nas temperaturas de 600 e 700ºC. As micrografias mostraram que ocorreu refino do grão, típico do processo estudado. Ensaios de nanodureza Vickers mostraram um aumento considerável na dureza, mostrando que o teste de torção é uma ferramenta eficiente para simulação do processo ARB.

Oct 30, 2017

By Eugene Nel, Johan Theron, Chris Martin, Hans Raabe

"Impala Platinum Limited is the world’s second largest platinum producer, producing more than 1.7 million ounces of the precious metal last year, much of this from the UG-2 reef located in the Bushveld Complex, South Africa. As part of Impala’s ongoing expansion programme, tonnage through their principal UG-2 processing facility, near Rustenburg, was increased 40% in 2001.To accommodate the increased throughput, the role of the existing primary mills was converted from conventional semi-autogenous grinding units, to attrition and selective grinding units, operating in fully autogenous mode. The finer chromite and coarser silicate components in the mill discharge are then separated by screening and processed in dedicated circuits downstream. This way, the need to spend considerable capital to increase primary grinding capacity was averted.In the last year, considerable work has been conducted to evaluate and optimise the two downstream circuits. This has involved an optimisation programme of sampling and diagnostic flotation testing, supported with QemSCAN analysis. This paper will describe the operation of the new circuit. It will also describe some of the more novel aspects and interesting findings from the optimisation programme.INTRODUCTIONThe South African platinum industry is the world’s largest producer of platinum and the world’s second largest producer of palladium. Located in a wide area north of Johannesburg, the industry mines ores from the Bushveld Complex, one of the world’s great mineral treasure chests, containing over 70 percent of the world’s platinum, as well as extensive reserves of the other PGE (platinum group elements), chrome, manganese and vanadium. The industry employs about 180,000 people in, predominantly, underground mines, which together form an almost unbroken circle of mining operations 200 km in diameter."

Jan 1, 2004

By Madan M. Singh

Hydraulic mining has been practiced in the United States since 1852 and many mineral commodities, such as gilsonite, phosphates, lead-zinc, silver ores and St. Peter Sandstone can be mined in this manner. In 1958, the U. S. Bureau of Mines initiated research into the mining of coal using these techniques.1-4 These early investigations were conducted in the 5000 psi pressure range. The large nozzle diameters used in this pressure range produced extremely high flow rates which created visibility problems at the coal face, and required removal of large amounts of water from the mining area. Besides, the production rates were not much better than with mechanical methods. This indicated that with higher pressures the water quantities might be reduced using the same or higher horsepowers but enhanced breakage. For this reason intensive investigation in material removal using fine water jets at extremely high pressures (50,000 psi to 100,000 psi) has been undertaken. This was not the entire reason for this contract from the Bureau of Mines, however. The contract objective is outlined later. IIT Research Institute has done pioneering work in high pressure jet development in the United States.5-8 Similar schemes have been investigated abroad. 9-13 Hydraulic mining of coal at relatively low pressures is successfully being done in the Soviet Union, Japan, Canada, and most recently, in Germany.

Jan 1, 1973

By W. M. Brewer

Introduction This paper describes some of the mineral resources that are tributary to that portion of the Pacific Great Eastern railway included in the Western Mineral Survey District, No. 6, of British Columbia. This district extends 38 miles northerly from Squamish, the ocean terminus of the railway at the head of Howe sound, to Alta lake. Beyond Alta lake the railway continues northerly through two other mineral survey districts: the Central Mineral Survey District No. 3, and the Northeastern District No. 2. District No. 6 includes that section of the Coast Range from which the waters flow southerly towards Howe sound. The division between District No. 6 and District No. 3 is represented by an imaginary line across the summit between the headwaters of the Cheakamus river, flowing south into the Squamish, and the Green river which flows north and empties into the head of Lillooet lake near Pemberton meadows, about 20 miles from Alta lake. History: - The history of the route of the P. G. E. railway dates back to the old Cariboo days when a pack-horse trail traversed the country northerly from Squamish to the Pemberton meadows, and also south-easterly from Squamish to the head of Seymour creek, thence southerly down that creek to the north arm of Burrard inlet.

Jan 1, 1925

By Thomas M. Lynberg

WIDCO is a surface coal mine located near Centralia, Washington. The WIDCO preparation plant processes over 7 million tons of run- of-mine coal each year with a product yield averaging 72%. In the jig type preparation plant the fine refuse amounts to approximately 130 dry tons per hour of 28mesh by 0. This fine refuse material is thickened in a 160ft. diameter static thickener with the use of lime as a coagulant and organic polymer as a flocculant. Once thickened the fine refuse, which is predominately bentonitic clays, has been dewatered and disposed of using several different methods. These methods will be discussed and include vacuum disc filters, ponds, solid bowl centrifuges, belt filter presses and experiments with electrokinetic dewatering.

Jan 1, 1981

By Iara Janaína Fernandes

A casca de arroz é um resíduo amplamente gerado no mundo, é o principal subproduto do beneficiamento do arroz, e tem sido utilizada como biomassa para geração de energia, o que reduz o impacto ambiental causado pela destinação. No entanto, gera outro resíduo, a cinza de casca de arroz (CCA). A CCA é composta basicamente por sílica e carbono. Sendo os elementos traço mais comumente encontrados o sódio, potássio, cálcio, magnésio, ferro, cobre, manganês e zinco. Pelo elevado teor de sílica, é um resíduo com potencial para ser transformado em coproduto para diversas indústrias, porém, dependendo da aplicação pode ser necessária maior pureza. Assim, diversos estudos utilizaram a lixiviação ácida para reduzir o teor de contaminantes ou melhorar propriedades da CCA. Neste sentido, este trabalho teve como objetivo avaliar o beneficiamento de uma CCA residual através do processo de lixiviação ácida. Para isso, foram utilizados diferentes ácidos/concentrações, relações CCA/ácido e tempos de contato. Após estes testes utilizou-se análise elementar por FRX para caracterização química. Os resultados mostraram que o ataque ácido foi efetivo na redução ou eliminação de Fe2O3, K2O, CaO, P2O5 e ZnO para todos os ácidos e concentrações testadas. Sendo que as diferentes concentrações não afetaram a eficiência de remoção.

Aug 16, 2017

By S. K. Kawatra

Under normal conditions, a significant amount of pyrite is recovered in the froth during flotation of high-sulfur coal. In order to reduce this pyrite recovery, it is first necessary to determine the primary recovery mechanism, as different measures are required for reducing entrainment, locked-particle flotation, or true hydrophobic flotation. In this paper, evidence is presented which suggests that hydrophobic flotation is not the major mechanism for recovery of liberated pyrite, and that the bulk of the recovered pyrite is there either as a result of simple entrainment or by being physically locked with floatable coal particles.

Jan 1, 1991

By Juan Carlos Gentina

La biolixiviación de minerales es un proceso metalúrgico que permite el tratamiento de sulfuros insolubles y óxidos insolubles y ofrece beneficios económicos, ambientales y tecnológicos. En ese sentido, el presente texto señala un panorama de biominería y minería de cobre, la influencia de las variables operacionables más relevantes y su situación actual y presente en Chile.

Dec 1, 2013

By Peter Zhang

The immediate roof at the test site consisted of laminated clay shale that is likely to be susceptible to weathering. With seasonal dry-wet cycles in the mine ventilation air, the roof in the intake air would deteriorate and lose integrity over time. In many instances, the weathering-prone roof would gradually scale off piece by piece between bolts and over the entry corners. In some long-term entries, roof weathering could develop up to 2-3 ft deep with columns of bolted roof hanging under the upper intact roof. If wire mesh is used, the roof bags down and reduces the entry height, and the weight of the bagged roof tends to pull the bolts out and poses a safety hazard. An effective measure is always sought to support this type of weak roof that is sensitive to moisture degradation. One solution is to seal the roof shortly after entry development to prevent moisture penetration so that roof integrity can be maintained for the long term. In this application, a polymer-based sealing material was tested in the Rockspring mine for weathering protection and reinforcement. The material is a one-component polymer powder for spray application onto the roof and rib. The sealant material is mixed with water in the spraying nozzle to apply to the roof and rib as a paste. The product sets within 5-10 minutes and forms a membrane as thin as about 1/8-in. The membrane will quickly develop tensile and bonding strength within minutes and completely cure within a few days. Through sealing, bonding and lateral reinforcement, the integrity of the weak roof can be maintained. The material has been tried in a long-term evaluation over several months in a set of main entries in the Rockspring mine owned and operated by Rockspring Development, Inc., affiliate of Foundation Coal. Preliminary evaluation has shown that the material is an effective and economical solution to ensuring the long-term stability of weathering-prone roof.

Jan 1, 2009

By Prosper Lamothe

El presente texto describe la metodología ad-hoc para evaluar proyectos de Inversión estratégicos a través de la flexibilidad y la teoría de opciones reales. La clave de dicho enfoque metodológico radica en realizar la mejor proyección del precio de los metales aplicando las mejores prácticas mundiales al respecto. Para ello, se analizan una gran variedad de modelos concluyendo que el mejor modelo a aplicar, debe ser la simulación del precio del metal con reversión a la media con saltos de tipo aleatorio.

Sep 9, 2007

By Dale W. Richardson

Ductile hafnium was not obtained consistently by the conventional Kroll process. The bimetal reduction modification produced a more ductile hafnium by lowering the impurities, especially oxygen, in the sponge metal. Hafnium oxide was chlorinated in the presence of carbon to form anhydrous hafnium tetrachloride, which was reduced by sodium and magnesium in an inert atmosphere to produce sponge hafnium metal. After vacuum distillation to remove the byproducts, the sponge was arc-melted into ingot and rolled into strip. Metallic impurities were decreased by evaporating the hafnium tetrachloride from a fused salt. An excessive amount (over 1,200 parts per million (p.p.m.)) of aluminum was contained in some of the hafnium oxide, much of which remained as aluminum chloride in the hafnium tetrachloride during chlorination. Evaporation of the hafnium tetrachloride from a fused NaCI-KCI mixture during the Mg-Na reduction greatly lowered its aluminum content, as most of the aluminum and some of the other metallic impurities were retained by the fused salt.

Jan 1, 1961

By J. S. Pitsillos

A new furnace tapping technique involving the simulation of a control valve at the exit to a furnace is being investigated. The purpose of this new tapping technique is to regulate the flowrate of liquid furnace products( slags, metals and mattes). Numerical modelling and experimental work has been carried out on tapping of slags leaving a SIROSMELT reactor and the results found to be in good agreement. Numerical modelling has also enabled prediction of the important industrial conditions for the onset of blockage from the shape of the pressure versus flowrate curves. Slag launder experiments have been carried out and a one-dimensional heat transfer model was used to evaluate the effectiveness of launder covers and different coolants. From the experimental results and mathematical model some launder design guidelines such as inclination angle, covers and coolants have been developed.

Jan 1, 1991

By WALTER CARROLL

Between cross currents of economic factors and international expediencies the iron and steel industry in 1948 made an outstanding contribution to the general economic picture. Were it not for an unfortunate episode during the month of April involving a temporary shortage of coal, 1948 would have been an all-time record year in output. Exceeded in no previous peacetime year, the production of iron and steel in 1948 totaled some 88,500,000 tons. That it was a worthwhile effort of no small magnitude is evidenced by the fact that in three and one half years following the war, this nation has produced as much steel as in the five years preceding the war. This figure of 88,500,000 tons is 68 per cent greater than that for 1939.

Jan 1, 1949

By P Brown, M Nagarajan, A Green, P Dare-Bryan

Coal loss is an important issue at many coalmines, with losses of five per cent being common. The type of loss varies from mine to mine but is dependent on mine strata, the drilling and blasting processes applied and the mining method used. Typical coal loss mechanisms from the drill and blast process are coal roof damage and edge loss. Usually a reduction in coal loss is in direct competition with the need to provide material that is well-fragmented and a muck pile that has the required cast percentage. These competing issues were addressed over a two-year period at a mine in the New South Wales Coalfields by implementing a five-step approach. This was centred around building an understanding of the coal loss mechanisms utilising proprietary heave- modelling software, measuring coal losses by comparing survey to drill and/or gamma logs and implementing appropriate coal loss reduction processes. The end result exceeded expectations with a 95 per cent reduction in coal loss. Mine excavation productivity was maintained and coal loss minimised to less than one per cent of the in situ coal block.CITATION:Nagarajan, M, Green, A, Brown, P and Dare-Bryan, P, 2015. Managing coal loss using blast models and field measurement, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 429–436 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By William W. Shriver

When the Henderson Project is completed in 1975, it will become one of the Free World's largest primary molybdenum producers. The Henderson Mine will be located approximately 50 miles west of Denver, Colorado, on the eastern slope of the Continental Divide. Ore reserves are currently estimated to be 303,000,000 tons with a grade of 0.49% MoS2. The mill and tailing area will be located approximately 14.5 miles from the mine in the Williams Fork Valley, which is on the western slope of the Continental Divide. Ore haulage from the mine to the mill will be by ten miles of underground railroad and 4.5 miles of surface railroad. The concentrator has been designed to mill 30,000 tons per day and will yield approximately 50,000,000 pounds of contained molybdenum per year. This paper is concerned with the tailing and water supply system for the Henderson Project and in particular the environmental considerations affecting their design.

Jan 1, 1970

By V. I. Lakshmanan

Process Research ORTECH Inc. (PRO), with its in-depth knowledge on cobalt behaviour in nickel matte smelters and its novel mixed chloride hydrometallurgical processing, is developing a hybrid process to enhance cobalt recovery. PRO’s experimental data is compared with plant information on cobalt behaviour in smelters. In final stages of iron rejection in the converters, the thermodynamics of the matte-slag system dictates the undesirable transfer of the cobalt to the final converter slags. This results in much lower cobalt recovery in the product Copper/Nickel matte (<60%) in present copper and nickel smelters. This information is used to transfer cobalt into desired quantity of converter slag. The enriched cobalt slag is subjected to PRO mixed chloride process to recover nickel, and cobalt as high value salts of importance in lithium ion batteries. From a typical converter slag containing 3.5% Ni, 1.5% Co, and 1.0% Cu, PRO leach process extracts 98 % Ni, and 98 % Co, and 99% Cu. Application of this process to enhance cobalt recovery in typical Copper/Nickel smelters is presented. In addition, this will also enhance the Copper and Nickel recovery. Both these aspects are of interest to the Copper, Nickel, and cobalt producers. INTRODUCTION In pyrometallurgical extraction of copper and nickel from sulphide ores cobalt often occurs with copper and nickel. The requirement of cobalt is increasing due to its need in lithium ion cells used in electric vehicles. Therefore its efficient and economical extraction in a form suitable for use in lithium batteries is of great interest at present. In the pyrometallurgical processing of copper and nickel sulphide concentrates the concentrate is smelted to produce a furnace matte, which is then sent for converting to remove the iron to produce iron free (~1% Fe) matte for further processing to copper or nickel matte. The copper/nickel matte is processed for metals recovery by hydrometallurgical or vapo-metallurgical or oxidation – reduction routes to make market products. As shown in Figures 1 and 2 the slags are produced in the smelting step and in the converting steps. The metal losses in smelting are controlled by the oxygen pressure in that step and slag production which is controlled by concentrate grade. The slag produced in the converting step which is carried out at a higher oxygen pressure contains higher level of metals is often returned to the smelting step to increase value metals recovery.

Jan 1, 2019

By Yuan Zeping

This paper describes the distribution and removal of the main impurities in the pyrometallurgical process ?at the Guixi Smelter. The paper discusses in detail our converting schedule?of3S-SB and injecting deeply a mixture ofNa2CO) and CaO flux into the converters to enhance impurity removal.

Jan 1, 1998

By Laércio Rosignoli Guzela

Neste estudo uma liga AA6061 foi processada por Extrusão Angular em Canal (EAC) com até quatro passes, a partir de duas condições iniciais diferentes, solubilizada e estabilizada, sendo imposta uma deformação verdadeira de 1,05 a cada passe. As amostras processadas foram caracterizadas através de ensaios de dureza e de análises de calorimetria diferencial de varredura. Tratamentos anisotérmicos foram aplicados após a EAC em condições escolhidas através de calorimetria diferencial de varredura. Observou-se que, devido à microestrutura gerada pela deformação imposta, uma parcela significativa do endurecimento total é obtida após o primeiro passe. As análises de calorimetria diferencial de varredura mostraram que nas amostras deformadas a sequência de precipitação é modificada em relação àquela observada na ausência de deformação, sendo suprimida a formação da fase b¢¢. Ao final dos tratamentos anisotérmicos, observou-se que o valor de dureza das amostras era menor do que o valor inicial, devido à recuperação e à precipitação da fase b¢, menos endurecedora.

Aug 16, 2017