Search Documents

By Norman M. Junk

Following the wide-spread acceptance of ANFO as a useful, low cost blasting agent, studies have been made to adequately describe the physical and explosive properties of this material (1). As the quality of the AN blasting prill improved, reliability and sensitivity to initiation were greatly increased and many methods of priming were chosen from the standpoint of economics with little appreciation for the need to initiate so as to obtain the most efficient detonation. Under certain conditions, ANFO could be initiated with primers no more powerful than a No. 8 blasting cap (2). Research on primers for ANFO followed and it was demonstrated that this blasting agent was subject to extreme transient velocities upon initiation with wide variations in energy output depending upon the nature of the primer. For these reasons it was shown that powerful priming was economically justified (3). These studies helped to define the properties of an effective primer and the guides for its efficient use. In the vast surface coal mining industry, technological advances in earth moving equipment were paralleled by the development of larger and larger borehole drills (4). Even though ANM) was the major blasting agent used in this industry, investigations of priming techniques in these larger boreholes was almost non-existant. In 1962, Mr. Cleon Woolsey of Enos Coal Company disclosed to the industry that dramatic improvements in blasting production could be achieved with new priming and boostering methods (5). The research program at the Atlas laboratories was designed to explain these results and extend the study of initiation of ANFO with both high explosives and slurry explosives and to define the principles involved.

Jan 1, 1968

By R. R. Sayers

The contemplated use of dichloro-difluorco methane in domestic and commercial refrigerating appliances and in air-conditioning equipment for public buildings and possibly homes, brims attention to the health hazards involved in a wide potential exposure of the public to vapors of another new product, and for the first time to vapors of an organic fluorino compound. The objective in the development of this new refrigerant, however, has been the mitigation of health and explosion hazards in automatic refrigeration, and accordingly these factors have been given primary attention. Early in the development, the Bureau of Mines as requested to make a laboratory study of the toxicity and potential hazard, and it was ca the oasis of the results is of this work and the results of a preliminary investigation made in another laboratory6 that the compound has been selected for commercial use. The investigation conducted by the Bureau of Mines is still in progress, enough information has been obtained to indicate the order of the toxicity and the magnitude of the health hazards involved in the use of dichloro-difluoro methane as a refrigerant. The following is a summarized report of the work completed to date:

Jan 1, 1930

By O. C. Blade

"INTRODUCTION This report on the properties of motor fuels sold through service stations in the United States is a continuation of a series of reports made in accordance with a cooperative agreement between, the Coordinating Fuel Research (C.F.R.) Committee of the Coordinating Research Council (C.R.C.) 3/ and the Bureau of Mines of the United States Department of the Interior. The first of these reports presented data on motor gasolines sold during the winter of 1935-36.-4/ Further reports have been issued describing motor gasolines sold during the succeeding summers and winters to the summer of 1941 and during the winter of 1942-43 and the summer of 1943 5/ No reports were made on motor gasolines sold during the winter of 1,) 41-42 and during the summer of 1942. The present report presents analytical data for 1,356 samples, representing the products of approximately 103 companies. As in previous surveys, the companies covered by the survey include both large and small suppliers. Conforming to former reports, the data cover three groups of samples - regular-price, premium-price, and third-grade gasolines - and each group has been averaged separately. The number of samples, items and brands comprising each group is as follows: Regular-price, 770 samples, 286 items, and 94 brands; premium-price, 537 samples, 236 items, and 72 brands; third-grade, 49 samples, 31 items, and 18 brands. The meanings of these terms as used in the surveys are as follows:"

May 1, 1944

By H. E. T. Haultain

I HAVE considerable hesitation in preparing and presenting this paper. These machines have been such an intimate part of my own experiences and predilections for such a long time that J would find it difficult to tell the story in an impersonal way. They have had several attractions for me. They were needed for the study of the fundamental features of modern milling, size analysis and accurate batch concentration of the very fine particles. I had been a millman once, a real operating millman, and, when I became academic". I always had the craving to link the academic laboratory with the field, as Rittinger and Richards had done. My first milling experience was with a small concentrator at a tin mine in Bohemia, forty-seven years ago. There was no assay office and the testing of our tailings was by means of a "Vanning Shovel", introduced from Cornwall by Captain Josiah Thomas, the great Josiah of Dolcoath, some fifteen years previously. This was a most effective instrument and it has always been a puzzle to me that it has not been more universally used by millmen. Later, at Freiberg, on the other side of the Erz Gebirge from the tin mine, I was introduced to the "Sichertrog", made out of wood shaped something like a very shallow boat or an elongated saucer, a most effective piece of apparatus when. the difficult technique of handling it was once achieved. Later, in the Slocan in British Columbia, my partner, the late Maurice Bucke, used a short length of flat trough or launder suspended by four wires, with which he got very satisfactory results as a small batch concentrator. In the University laboratory we had frequent need for something of this kind, and many efforts were made to solve the problem. With W. E. Johnston, we were working on the problem of gold-bearing telluride ores, which called insistently for a separation of the very fine telluride particles which existed only in minute quantities in the Kirkland Lake ores. Under this spur there finally developed the Superpanner, which is a mechanized combination of the Vanning Shovel, the Sichertrog, and the Maurice Bucke suspended launder.

Jan 1, 1937

By V Cullinan, D Buchanan

The Brunswick plant is located in Costerfield, approximately 40km east of Bendigo in central Victoria. Crushing, grinding, gravity gold concentration and flotation methods are used to produce a saleable gold concentrate and an antimony-gold flotation concentrate. This paper discusses the improvements made within the processing plant which have resulted in a 99% increase in throughput over nameplate capacity of 6 250 average tonnes per month to 12 445 average tonnes per month and increases of 12% gold (from 2007 average of 78% to 2014 average of 90%) and 16% antimony recovery (from 2007 average of 79% to 2015 average of 95%). This combined effort has resulted in an increase of equivalent gold ounces (AuEq oz) produced from 2010-2014 of 15 872 to 82 574 – a 66 702 increase.AuEq oz= Au oz +Sb t × Sb (US$/t)Au (US$/oz)CITATION:Buchanan, D and Cullinan, V, 2015. Improvements in bi-metal production at the Brunswick Plant, Costerfield, in Proceedings MetPlant 2015, pp 267–272 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

Removal of Thiocyanate from Solutions by Precipitation

Sep 13, 2010

By Grigori Abramov

As we enter into the 21st Century, miners are looking more attentively at new mining technologies allowing decrease environment damage along with operational cost. This technic would allow developing of poor and difficult mineral deposits, including the World Ocean offshore zone. Borehole Mining is an underground/underwater remote method of mining carried out from floating platforms or vessels. Definition of Borehole Mining (BHM), working schematic, main technical data and its advantages are given. The method is currently in use in mining of different type of raw materials, such as: uranium, iron ore, quartz sand, coal, polymetallic ores, phosphate, gold, diamonds, rare earths, amber and more. It is also in use in oil and gas stimulation, salt domes storages building and environmental problems solution. Recently recorded data of Borehole Mining productivity (80-100 t/hour/hole) and a depth of mining (over 1 km) has been achieved in a last couple years. Remoteness of method not only secures complete safety of operations but also allows wide sector of underwater applications. The World leaders in Borehole Mining are Russia and the United States. Based on previous experience the Universal Tool for Seabed Borehole Mining has been developed for wide sector of usage: from exploration and mining - through oil & gas stimulation to souterrain storages construction and lake's bottom cleaning.

Jan 1, 2000

Reduce injury to people or damage to equipment when a scheduled production blast is detonated. Approach The essential elements of an effective blast area security system were identified through case studies of five mining operations where the blast area guarding practices were considered to be superior to those generally found in the industry. These elements were used in making recommendations for improved blast area safeguarding practices. Background The blast area security system is a means by which the mine operator prevents injury to people or damage to equipment when blasting is performed. Analysis of blasting accidents showed that most blasting accidents occur during scheduled blasting and are due to inadequate blast-site security. Factors contributing to the system's breakdown are failure to clear the blast zone, inadequate guarding. and failure of personnel to follow instructions, retreat to a safe location, and/or take adequate cover. Mine personnel, visitors and even trespassers can inadvertently wander into a blasting zone unless proper procedures exist to ensure that all personnel are cleared from the blast zone and kept safely away until after blasting IS completed. Statistics show that the blaster is the miner most frequently injured In these accidents.

Jan 1, 1986

By John Dodd

Advances in the technology of abrasion resistant irons and steels, which could help in combating abrasion and wear in mining operations, are reviewed. Nodular irons alloyed with nickel or copper and molybdenum, with acicular, bainitic or bainitic-martensicic microstructures are described. These alloy irons combine excellent castability and relatively easy machinabilitv with good resistance to wear. Recent progress in the development of high chromium molybdenum alloy irons is outlined, by which high temperature heat treatment of massive castings can be eliminated, alloy costs can be reduced and cracking problems avoided. Data is also given on the erosion-corrosion resistance of these irons. Trends in the development of improved cast steels are outlined. Factors influencing the toughness and abrasion resistance of manganese steels are considered. The 6% Mn 1% Mo manganese steels are shown to have a useful combination of toughness and abrasion resistance. Composite castings are seen as a means of com- bating abrasion in applications involving severe impact. A brief appraisal is given of recently developed martensitic wrought steels with improved weldability.

Jan 1, 1981

By T. Neesse

In many cases, the use of hydrocyclone control is desirable for the stabilization of separation in the setting of changing feed conditions. Control concepts based on exact mathematical models are not satisfactory due to the complexity of the physical process. In this case, fuzzy control is a suitable solution. The data are primarily derived from an optical sensor that monitors the outside view of the free underflow stream. A throttling valve, serving as an actuator, is installed in the overflow pipe that regulates the volume split of the cyclone. Applications in closed circuit grinding and in separation plants for tunnel driving, fine sand dewatering, and classification of kaolin demonstrate the typical use of this development. Additionally, the technological characteristics of the cyclone may be improved by this control, which is mainly caused by the increased discharge capacity of the un-der flow nozzle. A further advantage is the option to operate at an optimal operation point. In many cases, this point is located at the transition spray/rope discharge. The improved operation characteristics present new options for extensive applications of fuzzy cyclone control.

Jan 1, 2014

By J. Ye

A comprehensive flotation study has been carried out on a Chinese fluorspar ore using the packed flotation column developed at Michigan Technological University. The results are compared with that of a conventional mechanical flotation method on the same feedstocks. Key factors controlling flotation performance of both methods are evaluated based upon a simple statistic design. The flotation concentrate produced in one stage of the packed column has 4-S% higher recovery and much lower silica impurity content than that produced by up to six stages when a conventional mechanical cell is used. The results also show that the packed column flotation process is particularly suitable for recovery of finer fluorspar particles.

Jan 1, 1992

By M. Melashvili

"The SART Process was introduced to the gold mining industry in the late 1990s and several commercial plants were built over the following 10 to 15 years. Most of these plants have operated well and enjoyed plant performance in line with expectations based on the underlying chemistry of the process. However, two of the plants have consistently suffered from high reagent consumption and poor product quality, which has motivated a re-examination of the process fundamentals.The primary product in the SART Process is synthetic chalcocite, Cu2S, and the stoichiometric requirement for sulphide addition is therefore 0.5 moles per mole of copper in solution. It is shown here that when sulphide is added in excess of this amount (generally with the express purpose of lowering residual copper in solution) it not only fails in its intended purpose, but can have a negative impact on the settling and filtration characteristics of the copper sulphide product, as well as the final product quality. Moreover, these problems are exacerbated the higher the selected operating pH in the pH 3 to 5 range, and the longer the residence time of slurry in this pH range.Freshly precipitated copper sulphide compounds are known to be very fine and slimy, with poor settling and filtration characteristics. It is therefore important to engineer the SART Process in such a way as to encourage growth in the average particle size of the precipitate crystals. This was the rationale for recycling a portion of the thickener underflow to the primary reactor when the SART Process was developed. However, the theory of crystallization predicts that compounds of extremely low solubility, such as chalcocite (Cu2S: KSP = 10-48), are unlikely to experience growth in crystal particle size through heterogeneous nucleation and are more likely to grow through aggregation. On this basis, the SART practice of recycling a portion of thickener underflow to the primary reactor in the commercial plants is unlikely to lead to crystal growth via nucleation, and could in fact promote breakage of the aggregates that formed in the thickener. Recycling thickener underflow could therefore have the opposite of the desired outcome. The result of testwork that is reported here lends credence to this theory and questions the wisdom of recycling in the SART process."

Jan 1, 2016

By D. W. Boydell

The response of reclaimed gold tailings to acid leaching was investigated in the laboratory, followed by a pilot-plant program in which the operations of CCD, CIX and SX were tested with plant feed material. These results formed the basis for the design of the extension to the existing uranium plant at Blyvooruitzicht Gold Mine, commissioned in July 1977. This circuit consists of slimes-dam reclamation by bucket-wheel excavator at a rate of 100,000 t solids per month, acid leaching in pachucas, a five-stage CCD washing section, two parallel C1X absorption columns and two elution columns, SX and an ADU precipitation section. Barren solution is recycled to the CCD section as wash and to the repulper at the slimes dam. The performance of the plant during the first year of operation is compared with the predictions on which the plant design was based. Rated capacity was achieved within three weeks of start-up at a nominal dissolved uranium recovery in the ion-exchange section of around 98%. Owing to recycle, the over-all recovery in the ion-exchange and solvent extraction sections is somewhat higher than this figure.

Jan 1, 1979

By E. Chin

The Asia and the Pacific region has large mineral resources of antimony, barite, bauxite, bismuth, copper, fluorspar, gold, graphite, iron ore, magnesite, mica, rare earths, salt, talc and pyrophyllite, titanium, zinc, and zirconium. The region overall lacks large resources of oil and natural gas, but it has large resources of anthracite and bituminous coal. In terms of exploitation, many minerals, metals, and fuel are produced in significant quantities in the Asia and the Pacific region as shown in table 1. Collectively, the area accounts for a substantial amount of the world production of antimony, barite, bauxite, fluorspar, gold, graphite, ilmenite and rutile, iodine, iron ore, lead, magnesite, manganese, nickel, salt, tin, tungsten, and zinc. Total coal production of the region exceeds 1.6 billion metric tons. The production of bituminous coal accounts for more than 80 % of the total output. China is the region's largest coal producer, with an output of almost 1.1 billion tons. Other major producers are Australia and India. The combined production by Australia, China, and India is more than 1.5 billion tons or 93 % of the area's output. The remainder of the coal output in the region comes from Afghanistan, Cambodia, Indonesia, Japan, the Korean peninsula, Malaysia, Mongolia, New Zealand, Pakistan, the Philippines, and Taiwan. The production of crude oil throughout the Asia and Pacific region is close to 2.4 billion barrels. China and Indonesia together account for 67 % of the total output. The remainder of the output is primarily from Australia, Brunei, India, and Malaysia. Indonesia is the largest producer of natural gas in the region with an output of close to 58 billion cubic meters, followed by Malaysia and Australia with 23 and 22 billion cubic meters, respectively. Other producers in the region of lesser stature by output include Brunei, China, India, and Pakistan.

Jan 1, 1993

By Leonardo Camilo dos Reis, Edmilson Fernandes Dadomi, Claudio Silva de Paulo

In the hot strip mill production, one of the factors that may affect the productivity is the occurrence of failure due to the geometry of the strip at the exit of the rolling mill, because the tip of the strip can turn-down or turn-up. This study had the objective of evaluating the behavior of the strip when leaving the working rolls, through numerical simulation, aiming to know the influences of the main variables that govern the formation of the turn-down. The methodology consisted in performing the computational simulation of the strip mill and to vary the operational and geometric parameters that could influence the process. The results showed that the rolling of hot strips of HSLA material with final thickness varying between of 3 to 6 mm and a reduction of 6.6% to 11.0% in the last stand of a hot strip mill, tends to bend towards the roll with larger diameter, higher friction coefficient , higher temperature and lower limit of material flow. It was observed that the variation in diameter is the main factor that contributes to the formation of the curvature of the front-end of strip. Based on these results, several measures were implemented in the industrial line, with a significant reduction in the occurrence of turn-down.

Oct 2, 2019

By D. Jacobson

There are many different machine setup parameters and variables that affect the production of cone crushers in a mineral processing plant. One of these variables is the eccentric speed at which the cone gyrates. In June 2012, pilot tests were conducted on a 200 hp high speed cone crusher to determine the production and operating conditions over a wide spectrum of eccentric speed. Every plant will have variations in the ore characteristics and feed rates throughout the life of the mine, and at times throughout a single shift of operation, which result in non-optimal use of the crushing energy and inconsistent process control. For high speed cone crushers, the crusher will exhibit a different capacity, power required, and discharge size distribution as the speed ranges over the design limits of the machine. This study documents the measured variation in production and energy efficiency both when the crusher was ran at full capacity as well as when the feed to the crusher was not sufficient to run at full capacity. Overall, the results match theory and the capacity and power fluctuated by 25% and 17%, respectively, over the speed range when operated full while there was an overall trend of slightly coarser discharge size distribution as the speed decreased. The results with the fixed feed rate were more telling, as the crushers had 4-14% higher production when making a theoretical minus 12.5 mm product when operating at the optimal speed as compared to the worst speed in the ?typical? speed range for this application. Secondary analysis of the fixed tonnage testing also showed that the power draw was more consistent with lower magnitude spikes at the higher speeds (higher cavity level), as on average the standard deviation of the power draw increased from 7% to 18% and the peak power spikes from 20% to 48% over the speed range tested. The findings lay groundwork for more efficient plant design. Varying the speed of the crusher can be used to tune the crusher speed during commissioning, adapt to changing ore conditions over long periods of time, or be used as a dynamic input into an advanced control system. Each action above would serve to make the crusher(s) more productive and more energy efficient, and would also have mechanical benefits for the machine. Key Words: cone crusher, ore reduction, process control, crushing efficiency

Feb 27, 2013

By Kaixi Jiang, Lan Li, Bang Wei, Haibei Wang, Yaping Feng

"China is currently the world's largest copper producer. In the last five years, 950 kt/y of smelting capacity was commissioned. Currently, about 1200 kt/y smelting capacity is under construction and about 2000 kt/y smelting capacity is under feasibility study. Ausmelt/ISA smelting and flash smelting technologies were commonly adopted in China. After the double-flash-smelter was first adopted in 2004, three new double-flash-smelters are scheduled. Recently, two new copper smelting technologies were developed in China. One is an improved bath side-blown smelting process, and another is the SK.S bottom blowing process. Both technologies have been in practice for over three years and have achieved good technical performance. Approximately 500 kt/y new smelting capacity in China and India will adopt these technologies. Both technologies have the advantages of low investment cost, low energy consumption and high flexibility for complex raw materials. This paper reviews ""green"" copper smelting projects in China and introduces the practices of the two new Chinese smelting technologies.IntroductionPresently, China is the largest copper producer in the world. As far as the smelting of copper is concerned, there are many smelting processes applied in industrial production, such as flash smelting, Noranda smelting, Ausmelt smelting, Isa smelting, the Mitsubishi process, Vanukov smelting, silver copper-smelting, SKS smelting, both side-blown smelting, traditional blast furnace smelting, electric furnace smelting, reverberatery smelting and so on . Except the last three traditional processes that are eliminated because of their failure to meet the requirements for environmental protection, all of the other above-mentioned methods are advanced smelting processes adopted nowadays."

Jan 1, 2012

By H. Van F. Furman

As the cyanide-method for the extraction of gold from ores is extensively used in the United States and elsewhere, and appears destined to prove a factor of increasing importance in the metallurgy of gold, a description of the latest laboratorymethods may prove of interest. The history of the development of the process in the United States has been analogous to that of all new processes. Many failures are to be recorded and a few successes. It is the opinion of the writer that, had the following simple tests been better understood, many of the failures would not have occurred, and we should probably have a larger number of successful plants in operation. While the process is not simple, but requires a high degree of chemical and engineering skill, the determination of the adaptability of an ore to the method is generally not difficult. While the laboratory-results will not always coincide with the actual results obtained in the mill, they will serve as a guide and control on the working of the mill, and mill generally suffice to determine if the ore can be

Jan 1, 1897

By Jim Slatter, Ben Collingwood

"It is well known that the adoption of an appropriate construction methodology is critical to quality outcomes for bored piles (drilled shafts). Many case studies have been published documenting quality issues that have arisen due to a range of causes involving ground conditions, ground support, drilling and cleaning techniques, groundwater, concrete properties and concreting methods, amongst other things. Despite the body of published information, pile defects remain common in practice. The authors share over 40 years’ experience in the Australian piling industry and have participated in many hundreds of projects involving bored piles in design, construction and testing roles. It is the authors’ experience that many defects are caused by conditions or practices that are known to be problematic, but that are often not recognised or addressed at the time of the works. This paper provides an overview of industry practices and key factors relevant to quality outcomes. The authors draw upon their own construction experience, published case studies and guidelines, and observations from independent pile testing activities they have been involved in across the Australian piling industry. The intent of the paper is to provide a consolidated review of typical industry practices and to highlight key areas in which construction quality can be enhanced.INTRODUCTIONThere are many published studies of cases where bored piles have been constructed and found to have concrete defects. The authors have had personal involvement in many cases where the outcomes and learnings are not publically available. The nature and cause of defects is always dependent on site and project specific factors, and therefore methodologies and materials that produce satisfactory outcomes in certain circumstances may be problematic elsewhere. The process of bored pile construction encompasses the following key areas:??excavation and ground support;??pile preparation and cleaning;??pile reinforcement and fitments.??concrete supply and mix performance;??concrete placement methodology;Each of these elements is equally important and can influence construction quality in completed piles. In the authors’ experience, it is often a combination of seemingly minor issues that leads to significant defects in piles. Conversely, attention to detail in all aspects of bored pile construction is required to produce outcomes of a consistently high standard."

Jan 1, 1900

By Lyle F. Smith

With the demand for larger diameter raises under all ground conditions and the increasing price of drill rods and operating costs, it was evident that there was a need for a raise borer with a variable-speed drive and fast-response torque limiting control. The raise boring machine described in this paper was developed after several years of market research and discussions with mine operators and construction contractors. This paper discusses the Ingersoll-Rand raise borers with the solid-state controlled DC motor drives. These machines have gained wide acceptance in the five-year period since being placed in operation and are designed to accommodate the range of raise diameters and lengths most required today.

Jan 1, 1978