Search Documents

By L. P. Davidson

ThE new electrolytic zinc plant of the American Zinc Company of Illinois commenced operation in April 1941. The simple flowsheet using the standard current density and the economic reasons that dictated it are given herewith. The Evans-Wallower Zinc Co. built an electrolytic zinc plant at Monsanto, Ill., in 1929 and operated it for about two years. The plant stood idle from 1932 and was purchased by the American Zinc Co. in 1940. Because of the condition of the equipment, excepting the motor generator set, a complete rebuilding was necessary. The Fairmont City plant of the American Zinc Co. could treat the leach residues, the purification cake and the skimmings from the melting furnace in its various plants. This possibility permitted a simple flowsheet with good economic results. The flowsheet is shown in Fig. I. The calcined concentrates are leached in mechanically agitated tanks with spent electrolyte and such ferric iron solution as necessary. When the acid has been neutralized and the iron coagulated, the fluid is discharged to settling tanks. The underflow from these thickeners is filtered on a Moore filter; the filter cake leaves the plant for retreatment and the filtrate joins the thickener overflow. Zinc dust is added to this solution until the copper and cadmium are precipitated. The pulp is filtered through Shriver presses, which deliver the purified solution to stor- age tanks, and the copper-cadmium-zinc cake is shipped for retreatment and recovery of these three metals. The purified solution is electrolyzed; the regenerated acid is returned for use in the leaching plant and the cathode zinc, after stripping, goes to the melting furnace, from which it is cast in slabs. The skimmings from the melting furnace are shipped to the Fairmont City plant for reduction to metal in the retort furnaces. The choice of this simple flowsheet was made possible only because of the facilities of the Fairmont City plant. The long leaching pried, with high acid content and high temperature which characterize the high-density process, gives a higher zinc extraction but also dissolves more impurities, which must be removed. The same is true to a lesser degree of the multi-step leaching of the western low-density plants. By the sacrifice of some initial extraction, solutions can be obtained that are relatively easy to purify and give good ampere efficiency. This loss in initial extraction is made up in the retreatment of the residues in the Waelz plant. The impurities that accompany the zinc thus extracted are inconsequential when the Waelz product is treated in a distillation plant. It was recognized that this flowsheet would require a somewhat greater amount of sulphuric acid—-eithcr as acid or as sulphate sulphur in the calcine—because of poorer washing. The sulphuric acid plant at Fairmont City could deliver 60" Bè. acid to compensate for the sulphate loss and the cost would be less than the cost of more intensive washing.

Jan 1, 1943

By L. P. Davidson

ThE new electrolytic zinc plant of the American Zinc Company of Illinois commenced operation in April 1941. The simple flowsheet using the standard current density and the economic reasons that dictated it are given herewith. The Evans-Wallower Zinc Co. built an electrolytic zinc plant at Monsanto, Ill., in 1929 and operated it for about two years. The plant stood idle from 1932 and was purchased by the American Zinc Co. in 1940. Because of the condition of the equipment, excepting the motor generator set, a complete rebuilding was necessary. The Fairmont City plant of the American Zinc Co. could treat the leach residues, the purification cake and the skimmings from the melting furnace in its various plants. This possibility permitted a simple flowsheet with good economic results. The flowsheet is shown in Fig. I. The calcined concentrates are leached in mechanically agitated tanks with spent electrolyte and such ferric iron solution as necessary. When the acid has been neutralized and the iron coagulated, the fluid is discharged to settling tanks. The underflow from these thickeners is filtered on a Moore filter; the filter cake leaves the plant for retreatment and the filtrate joins the thickener overflow. Zinc dust is added to this solution until the copper and cadmium are precipitated. The pulp is filtered through Shriver presses, which deliver the purified solution to stor- age tanks, and the copper-cadmium-zinc cake is shipped for retreatment and recovery of these three metals. The purified solution is electrolyzed; the regenerated acid is returned for use in the leaching plant and the cathode zinc, after stripping, goes to the melting furnace, from which it is cast in slabs. The skimmings from the melting furnace are shipped to the Fairmont City plant for reduction to metal in the retort furnaces. The choice of this simple flowsheet was made possible only because of the facilities of the Fairmont City plant. The long leaching pried, with high acid content and high temperature which characterize the high-density process, gives a higher zinc extraction but also dissolves more impurities, which must be removed. The same is true to a lesser degree of the multi-step leaching of the western low-density plants. By the sacrifice of some initial extraction, solutions can be obtained that are relatively easy to purify and give good ampere efficiency. This loss in initial extraction is made up in the retreatment of the residues in the Waelz plant. The impurities that accompany the zinc thus extracted are inconsequential when the Waelz product is treated in a distillation plant. It was recognized that this flowsheet would require a somewhat greater amount of sulphuric acid—-eithcr as acid or as sulphate sulphur in the calcine—because of poorer washing. The sulphuric acid plant at Fairmont City could deliver 60" Bè. acid to compensate for the sulphate loss and the cost would be less than the cost of more intensive washing.

Jan 1, 1943

By R. W. Gurry

THERMODYNAMIC calculations indicate that boron is a better deoxidizer than silicon but probably is not quite as effective as aluminum. Boron should, therefore, be readily oxidized out of the open-hearth bath, which implies that it is not recovered in significant concentration from any scrap charged; also that, if added in the ladle, it tends to oxidize out during teeming unless protected by the presence of a. better deoxidizing agent. These conclusions do not apply to liquid cast iron, in which the oxygen content is much lower than in liquid steel. The possibility of conserving certain strategic alloying elements widely used in steelmaking, notably manganeie, chromium and molybdenum, by the use of boron, which in small concentration appears to be extraordinarily effective in promoting hardenability, raises a question as to what extent any boron present in the scrap charged into the open hearth is oxidized out during melting and subsequent refining. This question is significant because the optimum concentration of boron in the finished steel, which is fairly critical, would be very difficult to attain if the boron in the charge were largely retained in the metal. Moreover, unless boron is substantially eliminated in the open-hearth process its use on a large scale would eventually make it impossible to produce boron-free steel except by restricting the charge to virgin material. There is at present, unfortunately, virtually no satisfactory direct evidence to provide an answer to this question; but there are indications from practice that boron is oxidized out in the open hearth in the production of medium or low-carbon steel, although it may be retained if the carbon content remains fairly high; that is, if the oxygen is kept fairly low. In the absence of direct data, it is necessary to rely upon the indications of indirect evidence, the best approach now available being a thermodynamic calculation of the deoxidizing power of boron in liquid steel by the general method used so successfully by Chipman1 in his study of the reactions in the open-hearth process. The thermal data for boron, upon which such a calculation must be based, are reasonably satisfactory; the only quantities not directly determined are the entropy of melting of boron, the activity coefficient of boron in liquid steel, and the activity coefficient of B203 in an open-hearth slag; but these values may be estimated with ample accuracy. The results of this calculation, which is presented later, are given in Table I, together with corresponding data for other deoxidizing elements. This table shows the calculated residual content of oxygen in equilibrium with different residual concentrations of the deoxidizer in the metal;

Jan 1, 1943

By C. B. Kenahan

A summary of Bureau of Mines research on recycling, reuse, and disposal of mineral-, metal-, and energy-based wastes is presented, accompanied by an extensive bibliography of related publications. The Bureau's waste recycling and disposal program is directed toward the following four main areas of research and development: (1) extraction of mineral, metal, and energy values from urban refuse; (2) upgrading and recycling of automotive and related ferrous and nonferrous scrap; (3) recovery, utilization, and stabilization of mine and mill processing wastes, and (4) recovery and reuse of values from industrial waste products. This publication updates Bureau of Mines Information Circular 8529, which was issued August 1971.

Jan 1, 1973

By P. H. Tumialán

Dado que la veta El farallón del batolito de la Costa en Huarochirí, Lima, fue alimentada por flujos hidrotermales horizontales, se prevee que la mineralización de los flujos horizontales forman parte final del flujo de ascenso vertical, que en los yacimientos anteriores no se pudo hallar. En esta perspectiva, para la veta señalada, el zoneamiento con eje horizontal en sentido contrario al flujo mineralizante, es de plata, cobre, plomo, zinc y oro. En consecuencia, el concepto genético y el zonamiento hallado se convertirá en una guía para la exploración geológica de estos yacimientos, donde no solo hay flujos horizontales hidrotermales en rocas volcánicas estudiadas en Julcani por U. Petersen, sino también en rocas sedimentarias e intrusivos.

Oct 14, 1980

By Yunnen Chen

The test and use of natural materials as biosorbents for the removal of heavy metals from industrial wastewater is under constant development. In the present study, the biosorption capacity of waste microzyme was studied for cadmium The cadmium removal study has been carried out batchwise where the influence of physico-chemical key parameters such as pH value of solution, contacting time and initial cadmium ions concentration have been considered. The influence of metal ion concentration was evaluated and the results were fitted using adsorption isotherm models. The kinetic of cadmium biosorption was also investigated. The maximum percent removal was attained at the pH 7.0 after about 30 min. Waste microzyme was a potential biosorbent for the removal of Cd(II) from the effluent of electroplating industry.

Jan 1, 2009

By M. J. Beus

Many mines in Canada, the United States and South Africa are reaching the hoisting limit. Very little payload will be possible without compromising safety due to the excessive weight. It has been suggested (DeLorme, 2000) that one of the most attractive concepts to enable deeper hoisting is to reduce the allowable factor of safety in the wire rope. Researchers at the Spokane Research Lab are developing new technology to improve hoisting safety and productivity by providing new monitoring and analytical tools. A Shaft Conveyance Monitoring System (SCMS) has been developed which determines hoist rope end load, true conveyance position and acceleration, and rope safety factor, as well as other hoist operating parameters. This information is transmitted to the hoist operator display 20 times per second. Recent field measurements on 45 mm (13/4 in.) diameter hoist rope indicate that dynamic forces during loading of a 9000 kg (10 ton) skip could exceed the safety factor of the rope. To improve on the current understanding of the mechanical behaviour of hoist ropes, and to help interpret the results from field-testing of the SCMS, a new approach to computer modelling of stranded wire rope is also being developed. Particle Flow Code, PFC3D (Itasca, 1999), is used to simulate the structural behaviour of wire rope and the interaction between individual strands when the rope is subjected to static and dynamic end loading. Details of the SCMS, field results from the measured rope loads, and the results of numerical modelling on the wire rope will be discussed.

Jan 1, 2002

By V Novoselov, R Sabirov

Flotation processing technology of water-soluble minerals has made it possible to realise, since the 1960s, the wide scale industrial processing of potash and potassium-magnesium ores (about 200 million tonnes per year) as well as to create the multi-tonnage worldwide production of sylvite (KCl) for industrial and agricultural application. In this paper the particularities of the effect of reagents (blinders, collectors and frothers) during cation flotation in saturated saline solutions are outlined. New reagent modes for activating the effects of alkylamines during the flotation of KCl and the perfecting of technological flow sheets for processing potassium ore have been developed. The results of research on the reverse flotation of carnallite ore, with the help of alkylmorpholine û a new developing technology for benefication carnallite as raw material for the production of metal magnesium and fertilisers are listed. Examples are given of the industrial applications of processed reagent modes at potash flotation factories in Russia.

Jan 1, 2005

By José De Piérola

En los procesos de flotación y lixiviación de la producción de cobre se utilizan aguas recicladas y agua fresca. Este último es un insumo indispensable para ambos procesos, ya que constituye un elemento determinante del volumen de producción, así como un medio de vinculación obligado con el entorno social de las operaciones. En ese sentido, el presente texto describe la utilización del agua- en tanto representa un componente de rentabilidad relacionada al costo, al equilibrio del aprovechamiento con el comportamiento de la fuente y a la sostenibilidad con el entorno social, lo cual implica compartir el agua y recursos económicos para una planificación y adecuada priorización en su asignación.

Sep 9, 2007

By Da Zhao Gu

An important problem in rock engineering is to control the properties of artificial rock. A compaction technique for casting artificial rock specimens with controlled properties is described, i.e. using a compression-testing machine to compress the mixture. Uniform density is necessary to achieve uniformity of properties of the specimens, and uniform density can be obtained by using the specific pressing method presented. Rebound and borax content are important to the technique and have been studied as well.

Jan 1, 1992

By M. E. Volin

The Smuggler is one of the mines in the Aspen district, located the central part of Pitkin County, Colo. It was first examined in July 1943 by C. R. Wilfloy, former mining engineer of the Bureau of Mines at Salt Lake City, Utah, in, company with the lessees, R. D. Rohlfing of Aspen and J. W. Vanderwilt of Denver. The purpose of this examination was to sample a mineralized breccia zone that appeared continuous along the contact between the Leadville and Weber formations. These preliminary samples showed that the zone contains low but significant amounts of lead and zinc and that the minerals are partly oxidized and thus not easily concentrated. The mine was examined again in May 1946 by the senior author and William Herron, one of the present lessees of the property. This examination reviewed the previous sampling and recommended investigations by the Bureau of Mines. Sampling and drilling investigations were conducted by the Bureau from October 1946 to February 1947 and again from August 1947 to April 1948. Aspen is the center of a famous mining district that produced over $102,000,000 in silver and lead ores from 1880 to 1918, when a dispute closed down the mines (fig. 1). All of the workings below the Cowenhoven tunnel in Smuggler Mountain and the lower Durant tunnel in Aspen Mountain have been flooded since that time. The Cowenhoven portal now is caved, and Smuggler Nos. 1 and 2 tunnels are the only accessible workings in Smuggler Mountain. The only operating mine is the Midnight, situated 4 miles south of town at an altitude of 9,700 feet.

Jan 1, 1950

By Ing. R. Geutskens

Zinc-bearing dust from blast furnace gas-scrubbing operation is a well known environmental health problem in the iron and steel industry. Hoogovens IJmuiden (The Netherlands) developed processes to solve this problem. 90% of the zinc is concentrated in 25% of the dust (the fine particle fraction) by means of slurry-hydrocyclonage. The resulting fine particle fraction is treated in a pressure leaching process. Hydrochloric waste pickle liquors have been used as a leaching liquor. By creating optimal leaching conditions more than 98% of the zinc is brought into an acid' solution, whereas nearly all the iron remains in the residue. The zinc can be separated selectively from the solution. The residue can be reused in the blast furnace (via the sintering plant). In the article information is given about the research work and -results of the pressure leaching process as well as the possibilities of the process for solving comparible problems.

Jan 1, 1990

By Jerry T. McLendon

The proper disposition of phosphatic clays has been the subject of research and debated for years by phosphate producers, State and Federal research agencies, regulatory authorities, and environmentalists. To date, no "universal" solution exists for the ultimate disposl of phosphatic clays. This Bureau of Mines report examines the state of conventional clay disposal technology and reviews the technical progress of innovative alternatives. Twenty impoundment sites were investigated by the Bureau of Mines using geotechnical methods and laboratory analysis of cored samples. In addition, quasi-static cone penetrometer soundings were conducted to define clay and/or sand-clay interfaces en masse. Samples of the top, middle, and bottom hole segments were obtained at each station for laboratory studies of clay densities, pore fluids, plasticity, and mineralogical properties. The results of this study support the continued use of initial clay settling impoundments but emphasize the need for "in-line" systems to reduce the initial volumes of plant-generated phosphatic clays. The effective use of sand tailings is also encouraged to promote further consolidation of clays via self-weight stressing, sand-clay admixtures, and/or surcharging sand caps.

Jan 1, 1984

By R. J. Gray

Oxidation of coal can best be described as a process of deterioration, since most of the uses of coal, such as for fuel and by-product chemical and coke production, are adversely affected by coal oxidation, and the inclusion of oxidized coal in most coal products detracts from their value. There are probably many mechanisms of coal oxidation, and the ways oxygen molecules combine as complexes with coal macromolecules to form new substances have been dealt with and speculated upon by many workers1)* but are not dealt with in the present work. This study deals with tests and methods of detecting oxidized coal, with particular emphasis on the microscopically discernible changes that accompany the chemical and physical changes that affect the technological properties of coal during oxidation.

Jan 1, 1974

By R. A. Kleiv, H. Havskjold, N. Church, T. Malvik, M. Tro, E. Larsen

Liberation is one of the major purposes of comminution in mineral processing. In the simplest form, two or more minerals are present in a particle and have to be reduced such that the individual particles contain only one mineral. The complexity of the mineral intergrowth varies from ore to ore. Poor magnetic separation of iron ore may have many causes. In this paper, the emphasis is given to the problem of fine magnetite inclusions in quartz or other gangue minerals. This is highlighted by two Norwegian cases: one on a magnetite ore and the other on a hematite/magnetite ore. The inclusions in question are so small that they are not liberated by reasonable grinding. In both cases, the result has been either poor recovery or lower grade concentrates than desired. The first example concerns production of direct reduction concentrates from magnetite. Magnetic inclusions in gangue particles will be magnetized enough for the particles to pass into the concentrate. The second example is given a more detailed study, where the problem is caused by silicates with small inclusions of magnetite in a combined LIMS and WHIMS separation. This study included microscopy, Davies tube testing, and magnetization measurements. In particular, large gangue particles with magnetite inclusions were shown to have a tendency to bypass the LIMS separators as drag forces in presence of hematite are large. Such particles will then be picked up by the WHIMS as their magnetization is higher than for hematite. This was demonstrated by Davies tube tests, which indicated that such particles were picked up in preference to hematite particles. However, the Davies results did not give a good quantification. Magnetization measurements of gangue particles with magnetite inclusions was shown to be a better tool to quantify the magnitude of the effect of magnetite inclusions in magnetic separation.

Jan 1, 2018

By Behrouz Ohadi, Kamran Esmaeili, Bibhu Mohanty

In most metalliferrous open pit mines with heterogeneous orebodies, blast-induced rock movement is a crucial outcome that has unfavorable impact on ore and waste segregation in the post-blast muck pile, resulting in either ore loss (the ore is misclassified as waste and sent to the waste rock dump) and/or ore dilution (waste is misclassified as ore and sent to the processing plant). While many studies have been carried out to assess the influence of blast design parameters on blast-induced rock movement, the influence of rock mass characteristics in these studies have been overlooked.

Jan 1, 2018

By Derek Egan

"Abstract Construction clients want their foundation solutions to be right first time, every time; but it is often the geotechnical contractor who carries the most risk in achieving this. Robust validation to ensure that the installed geotechnical product is appropriate for the encountered ground conditions, will perform as required and be correctly measured for payment and record purposes is very important to minimise the contractor’s and the client’s risk. This paper outlines the development and operation of a robust real-time installation monitoring system which controls and validates the installation of driven cast in-situ (DCIS) piling. Using state of the art information technology the system allows the design engineer to interrogate the data acquired from the piling rig via his computer as the piles are completed. The use of the validation process, where data acquired during the driving of DCIS piles can be processed to estimate the finished pile performance, will be explained with reference to a new case study on large diameter DCIS piles. Examples of the routine use of the system will be presented to illustrate how automated monitoring of installation parameters can be used to raise the standard of reliability, efficiency and sustainability on piling projects. The conclusions to the paper will cover the key features and operational challenges characterising real-time monitoring of the execution of geotechnical works as developed from a number of years of experience of using a rig based data acquisition instrumentation system.INTRODUCTIONDriven Cast In-Situ (DCIS) piles have a long and successful history of use worldwide. The process, where a temporary steel drive tube, sealed at the bottom with a sacrificial base plate, is driven into the ground and filled with concrete before the tube is withdrawn, is well known (BS EN 12699, 2001 and Egan, 2013). Examples of large structures supported on DCIS piles installed by Keller UK include the Millennium Dome (now the O2 Arena) and the 2012 Olympic stadium in London.In recent times advances in piling rig instrumentation and telecommunications have enabled a new level of sophistication in the recording of installation parameters and the validation of pile performance. It is now possible to embed these features into the DCIS design and installation process which has improved the quality and efficiency of DCIS piling.This paper summarises the development and operation of a real time data acquisition and processing system for DCIS piling, but which is equally applicable to other forms of driven piling (for example concrete precast piling)."

Jan 1, 2014

By Clifford S. Gibson

A year ago a paper (1) was presented at the Annual Western Meeting of the Institute regarding silicosis in Ontario mines. It described the whole problem as we see it and discussed the means of prevention. The work and aims of the Technical Silicosis Research Committee of the Ontario Mining Association, and of the Committee's field engineer, were fully described also and it is suggested that reference be made to this paper in order to have a better understanding of the observations which are presented now. These observations enlarge upon parts of the dust control measures already discussed and tell of general progress in the past year. They concern fifty properties, the majority of the operating mines, which vary in size from the hopeful prospect to established producers yielding 11,000 tons of ore daily. Most of these are gold mines; a few copper-nickel. The ores range from heavy sulphides to siliceous materials and they are mined by many methods from varying types of deposits. The majority of the latter are steeply dipping and all are found in Precambrian host-rocks. Up to the present, die greatest depth to which mining has penetrated is 6,400 feet.

Jan 1, 1939

By S M. Iveson, K P. Galvin, D Kumar

Dry separation of iron ore fines and other heavy minerals has previously been achieved using one of two main approaches. The first is an inclined table with an upward airflow via small holes to help form an autogenous dense medium. The second is based on fluidised beds comprising a dense medium formed by fine particles suspended in an upward flow of air. In either case, vibration can be introduced. This paper describes recent findings using a novel system referred to as the Sink-Hole Fluidiser, which utilises elements of both these two former approaches. This device consists of a conventional gas-fluidised bed of fine medium with a 1 mm aperture mesh located at the surface. This mesh contains relatively large holes that act as sink-holes. The fluidised media flows upwards through the sink-holes and then falls back into the fluidised bed via the fine apertures in the mesh. The particles being separated, which are much larger than the fine media, pass over these sink-holes, where they either sink or float. The sink-holes offer a more precise balance of forces, applied on a single particle basis, resulting in robust density separation.Experiments have been performed using 2.0–4.0 mm tracer particles of density varying from 2.4 to 4.8 relative densities (RD) separated in a 200 mm diameter Sink-Hole Fluidiser with a single 13 mm diameter centrally-located sink-hole. In this preliminary semi-batch work, it was found that the Sink-Hole Fluidiser was able to achieve sharp separations (Ep as low as 0.20). This work underpins the development of a new continuous steady-state Sink-Hole Fluidiser, applicable to the dry separation of iron ore fines.CITATION:Kumar, D, Iveson, S M and Galvin, K P, 2017. A novel sink-hole fluidisation method for dry separation of iron ore fines, in Proceedings Iron Ore 2017, pp 221–226 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By L. Iacopetti, A. Calderara, M. Perego, P. Perrone, T. Furusawa

De Nora, a global leader in the development, manufacture and sale of all DSA® anodes based on titanium coated with mixed metal oxide (MMO) for electrochemical processes will present key advancements made to Self-Protected Anodes (SPA) for metal electrowinning. (DSA® is a registered trademark of Industrie De Nora S.p.A., Italy). In 2017 pre-commercial demonstration cells were operated in industrial environment. The program’s focus was to fully demonstrate the SPA anode’s superior mechanical and electrochemical robustness during normal and induced dendrite shorting occurrences while providing quality of plating in commercial operation. De Nora specialists focus on key components, in particular the engineering of the self-protection system, DSA® anodes and catalyst formulation capable to cope with high levels of pollutants while providing long service life in the meantime. Results of field trials confirmed the expected anode performance and enabled the selection of the most suitable “SPA” structure, based on resistive protective elements. Summarizing the economic benefits to copper electrowinning tankhouse operation with De Nora’s self- protected all DSA® anodes are; Double-digits power savings Cobalt-free electrolyte operations Minimal dendrite shorting damage incurred at the SPA anode Smoother, uniform cathode deposits with tangible improvement on current efficiency Tankhouse operations producing lead-free copper quality cathodes, in addition to elimination of lead waste for improved operator health and environment. INTRODUCTION De Nora’s engineered “Value Technology Package” (“VTP”) for electrowinning, consisting of our DSA® anodes coated with mixed metal oxide specifically formulated for copper electrowinning in conjunction with an advanced self-protected full titanium anode (“SPA”), underwent an intense field qualification program, inclusive of the behavior under massive short-circuits as part of the field investigation, with the goal to select and appoint the ultimate design configuration of “SPA”. Optimized wireless-based monitoring system was included in the field program, demonstrating good functionality for cell parameters monitoring and remote shorts detection.

Jan 1, 2019