Search Documents

By N. Q. Huy

This paper describes the application of finite element analysis to simulate the static and quasi-static pile load tests in different drainage conditions. The possible effect of excess pore water pressure will be studied from the simulations results. The results show that the drainage condition has effect on the bearing capacity of a pile derived from the quasi-static pile load test. The excess of pore pressure reduces the pile toe resistance while it increases the pile shaft resistance. The factors which influence the effect of excess pore pressure are also discussed.

Jan 1, 2006

The reduction of titanium tetrachloride to trichloride can be achieved by employing hydrogen and electric arcs. It is possible to produce melts containing up to 50% TiCk in the eutectic mixture of LiCl/KCl by striking a D.C. arc at the surface in the presence of hydrogen and TiCl. vapour. If the electrode IS made to just penetrate the surface of the salt mixture, a hot zone results from the' high resistance contact with both lower chlorides and sintered titanium may be produced. The sintered metal forms just below the melt surface while the trichloride forms at the gaslIiquid junction.The "hotspot cathode" appears to offer a solution to the problem of producing coherent deposits as the spong'e metal can 'be continuously withdrawn in a similar manner to the "calcium process".INTRODUCTIONConsiderable interest has been shown for some years in the possible development of a cheap electrolytic process for the extraction of titanium metal, since a method using simple materials and cheap electric power would materially reduce the cost of production. Even when cheap starting materials are used, however, there exist several general difficulties in the operation of plant which both limit the speed of production and increase the cost of the product. It happens that most of the techniques so far tried produce a powder as cathodic deposit, and when this is the case the following difficulties arise:1. The whole contents of the bath must be treated with solvent in order to extract the 'metal powder which may itself tend to oxidise, and thus become contaminated.2. Fine metal powders, which often contain residual entrained salts, are less easy to consolidate by arcmelting than metal sponge.

Jan 1, 1956

By Yvon T. Maurice

Under the auspices of the Federal-Provincial Uranium Reconnaissance Program, a geochemical orientation survey was undertaken in an area of uraniferous Lower Proterozoic (Aphebian) rocks near Cape Dorset in southwest Baffin Island. The main objective of this study was to establish a methodology for a future reconnaissance geochemical program using lake samples over a 300-mile Lower Proterozoic rock belt that occurs along the southern coast of Baffin Island. Mineralogical and chemical studies of known radioactive occurrences, combined with detailed sampling of secondary environment media in the vicinity of the showings. indicate that uranium is the most significant pathfinder, despite considerable enrichment of other metals in the uraniferous rocks, Significant geochemical patterns produced by uranium in lake waters and uranium in lake sediments have been obtained, but their relative usefulness depends on the distribution of carbonate bedrock, which in turn affect the bicarbonate content of lake waters. In southern Baffin Island, because of erratic variation in lake-water alkalinity, it is recommended that both water s and sediments be sampled on a routine basis. The need for lake-water acidification to prevent depletion of soluble metal ions in samples resulting from adsorption on the walls of the containers and/or suspended solid matter is discussed briefly. The base metal potential of the area was examined in some detail and found to be significant, particularly for a Lower Proterozoic gossanous formation that occurs throughout southern Baffin Island.

Jan 1, 1977

By E. R. Bobicki

"Low-grade ultramafic nickel ores, while representing a large potential nickel resource, are difficult to process due to their serpentine content. Microwave treatment is proposed as a technique to improve the beneficiation of ultramafic nickel ores by converting the constituent serpentine to olivine. The present paper reviews the microwave heating response of ultramafic nickel ores and resultant changes in mineralogy, as well as effects on grinding and slurry rheology. Beyond nickel extraction, microwave treatment improves the mineral carbon storage capacity of ultramafic ore tailings, providing a potential source of additional revenue via the sale of carbon credits. The combined positive effects, considered in the context of the whole operation, suggest an economically viable process is possible.INTRODUCTIONAs high-grade deposits become depleted, the processing of low-grade ores has become increasingly important. One such resource is low-grade ultramafic nickel ores. While representing a large source of nickel, these ores are difficult to process due to their serpentine content. Serpentine is a phyllosilicate mineral consisting of 1:1 stacked sheets of silica tetrahedra and magnesium hydroxide octahedra. There are three primary polymorphs: lizardite (platy), antigorite (corrugated) and chrysotile (coiled, fibrous). The anisotropic nature and non-spherical morphology of serpentine particles leads to complex rheology. Suspensions of serpentine minerals, especially those of chrysotile, exhibit high viscosity and yield stress, which can have a negative effect on comminution, flotation and dewatering operations. In flotation, serpentine is known to slime-coat pentlandite, a valuable nickel mineral, and form bubble-fibre aggregates that report to the froth, reducing nickel concentrate grade and recovery. Methods used to counteract the effects of serpentine in processing include desliming, the addition of chemical dispersants, salts or acid, and dilution (Bobicki et al., 2014a). Microwave pre-treatment has been proposed as an alternative way to eliminate the deleterious effects of serpentine in ultramafic nickel ore processing by converting the serpentine to olivine via dehydroxylation, which occurs at 600-700oC (Reaction 1). Olivine is isotropic, consisting of isolated silica tetrahedra linked by octahedrally coordinated magnesium ions, and has the same surface potential as pentlandite at the pH of flotation (~pH 9). Furthermore, since olivine is more reactive to CO2 than serpentine, microwave pre-treatment creates an opportunity to store more CO2 in tailings, an attractive option for mining operations looking to increase their bottom line where carbon pricing exists."

Jan 1, 2018

By R Wolff

One critical factor in open pit mining projects is the estimation of the recoverable reserves. The reason for this is that at the valuation stage there is a lack of information about future metal prices and production costs. Consequently, the estimation of the recoverable reserves needs to be done based on a fixed break-even cut-off grade (BECG), in which fixed expected metal prices and production costs are assumed throughout the operating life of the mine (OLM). In this paper, an alternative technique for estimating the recoverable reserves of an open pit mining project is presented and explained in detail. The main characteristic of this technique is that it estimates the recoverable reserves of the project using mining costs as reference: this is done due to the fact that mining costs are easier to model than metal prices. Another important characteristic of this technique is that it uses the uncertainty of the geology of the orebody, given by simulations of the deposit, to make final strategic decisions, such as the selection of the operating life of the mine and the optimal production rate, which minimise the risk of not achieving future production targets while maximising the upside potential of future rewards. As it will be shown, the final outcome of the proposed technique is the generation of a robust open pit design, that include cutbacks and ultimate pit limits, called the marginal open pit mine design (MOPMD). One characteristic of the MOPMD is that, at each production period, it will be characterised by their respective geological uncertainty, given as probability distributions of ore, waste and metal quantities, and by marginal economical project indicators, such as cut-off grades and metal prices, among others. The details follow in the paper.

Jan 1, 2006

By Noel W. Kirshenbaum

Difficulties and costs of transport markedly affect Canadian mineral producers because of distance from markets, weather conditions and rugged terrain. The chemical and physical nature of sulphide concentrates presents additional difficulties in handling and transport, resulting in higher costs which are ultimately borne by the mineowner. Troublesome properties include the thixo-tropic character of wet concentrates, freezing, susceptibility to autogenous heating, and fine particle size causing spillage and dusting losses. Canadian mineowners and shippers must contend with these problems and with stringent regulations governing the maritime shipping of concentrates. A "systems approach," in which complementary techniques in materials preparation, handling and transport are integrated, could reduce freight costs and losses for those selling concentrates, facilitate operations for those carrying and handling them and, in some cases, improve metallurgical processes in smelters receiving them.

Jan 1, 1969

By M. M. Rajkovich, L. Adams, J. J. Zaluski, S. Gardner

In 1998, Kentuckians for the Commonwealth filed an Administrative Petition with the Kentucky Natural Resources and Environmental Protection Cabinet to designate 8,903 +/- hectares (22,000 +/- acres) on Black Mountain, which contains the state’s highest point, as unsuitable for mining. A fast track legislative process was triggered which could have "taken"100 million tons of coal reserves or, in the alternative, imposed severe restrictions on mining. Even with all parties represented by reasonable individuals, this process can be extremely cumbersome and expensive. The legal and technical preparation for this unusual hearing process as well as issues and strategies of the negotiated resolution are reviewed.

Jan 1, 2000

By José Wilmar Calderón-Hernández

Aços inoxidáveis supermartensíticos (AISM) são aços de matriz martensítica contendo baixos teores de carbono, abaixo de 0,03%. Eles vêm sendo utilizados na indústria de óleo e gás para aplicações específicas que exigem resistência mecânica aliada a moderada resistência à corrosão. Após serem temperados para a obtenção da estrutura martensítica, esses aços são submetidos a tratamento de revenimento para alívio de tensões e melhoria das propriedades de tenacidade e ductilidade. Durante o revenimento é esperada a ocorrência de mudanças microestruturais resultantes principalmente da precipitação de diferentes fases. Tais precipitados influenciam tanto as propriedades mecânicas finais quanto a resistência à corrosão desses aços. Nesta pesquisa foi avaliada a resistência à corrosão por pite de dois AISM do tipo 13Cr5Ni2Mo, um deles contendo Nb (0,11%), através de ensaios de polarização potenciodinâmica em soluções de 0,6M NaCl sem e com adições de 0,3M e 0,6M Na2SO4. Os resultados mostraram que a adição de Na2SO4 no eletrólito contendo NaCl inibe consideravelmente a corrosão por pite. Foi constatado também que o AISM contendo Nb apresenta maior resistência à corrosão por pite nos eletrólitos de misturas de cloreto e sulfato. Além disso, os resultados mostraram que o revenimento a 575°C melhora a resistência à corrosão por pite, comparativamente ao revenimento a 600°C. O melhor potencial de pite foi obtido para o aço ao Nb, revenido a 575°C por 2h, em eletrólito 0,6Na2SO4+0,6NaCl.

Jan 16, 2018

By Q. Wu

Neural network methodology is used to predict mean particle size resulting from rock blast fragmentation. A blast data base developed in a previous study is used in the current study. A part of this blast data was used to train a single-hidden layer back propagation neural network model for each of the similarity groups obtained in the same previous study. Levenberg-Marquardt algorithm provided the most stable and efficient training out of the four algorithms evaluated. An extensive analysis was performed using a part of the blast data to estimate the optimum number of units for the hidden layer for each similarity group. The remaining blast data are used to validate the trained neural network models. Capability of the developed neural network models is determined by comparing predictions with measured values and predictions based on one of the most applied fragmentation prediction models appearing in the blasting literature. Prediction capability of the neural network models was found to be strong and better than the existing most applied model. Diversity of the blasts data used is one of the most important aspects of the developed models. The developed neural network models are suitable for practical use at mines.

Jan 1, 2011

By H. Akbari

The ordinary Portland cement (OPC) is the key pozzalonic component of the concrete mix, widely used as the construction material world-wide. Billions of tons of OPC are used in the construction industry each year. However, calcinations of limestone and silica that produce OPC also produce almost an equal amount of CO2 during the cement manufacturing process. Thus, OPC production accounts for nearly 7% of all anthropogenic CO2 emission each year. The main objective of this study was to develop a geopolymer-based composite to be used as a substitute for OPC in concrete application to significantly lower the carbon foot print of the construction industry. A waste material produced during the coal combustion process was used as the main raw material for the geopolymer-based composite. It was mostly the non-metallic content of the F-type fly ash produced from the combustion of bituminous coal. The authors envisioned to extract some of the valuable metal oxides from fly ash prior to using the major non-metallic portion of the fly ash for geopolymer concrete application. The results obtained from this study exhibited that the compressive strength of the geopolymer concrete compares favorably with that of the conventional concrete prepared using the OPC.

Feb 27, 2013

By Gordon R. Haworth

During the past ten years we have experienced a period of rapidly-changing ground rules for the mining industry. Domestically we have had to contend with numerous new regulations controlling the impact of mining-related activities on the environment. However, for the purposes of this presentation we will assume that in the United States, after a certain amount of compromise on all sides, the industry will be able to work within the framework of the new regulations, and therefore we will concentrate on offshore developments. Due to the limitations in time and scope, this paper will be directed primarily toward the metal mining industry. We contend that the U.S.-headquartered mining company should remain active, and even expand its interests in foreign countries in the future. This is our feeling in spite of recent setbacks and the low return on investment experienced in recent years by some of the metal mining companies in their foreign operations.

Jan 1, 1975

By María Rocha, Benjamín Cebrián, Roberto Laredo

"Ring blasting designs have to achieve different goals in order to become efficient whether is done in up hole or downhole fashion. Ore recovery/dilution control, fragmentation and drift integrity all have to be taken into account when selecting parameters such as burden, spacing, linear explosive density and stemming. Blast energy simulation allows identifying contours of rock breakage and fragmentation, thuschoosing a combination of spacing at the end of holes and appropriate burden. Also, simulations are keyto concentrate energy levels on the mid part of the ring while making sure there is not too high of energy concentration around the drift, which integrity is needed for a safe ore mucking."

Jan 1, 2017

By P. H. Tumialán

Dado que la veta El farallón del batolito de la Costa en Huarochirí, Lima, fue alimentada por flujos hidrotermales horizontales, se prevee que la mineralización de los flujos horizontales forman parte final del flujo de ascenso vertical, que en los yacimientos anteriores no se pudo hallar. En esta perspectiva, para la veta señalada, el zoneamiento con eje horizontal en sentido contrario al flujo mineralizante, es de plata, cobre, plomo, zinc y oro. En consecuencia, el concepto genético y el zonamiento hallado se convertirá en una guía para la exploración geológica de estos yacimientos, donde no solo hay flujos horizontales hidrotermales en rocas volcánicas estudiadas en Julcani por U. Petersen, sino también en rocas sedimentarias e intrusivos.

Oct 14, 1980

By Lloyd Williams, R. E. Hershey, B. W. Gandrud

"1. The investigation shows that the Sewanee bed is the only bed of major importance in Marion County, 97 percent of the coal mined in the county having come :from this bed. There are coal reserves in minor quantity in the Battle Creek bed, and production from this bed depends on a few small truck mines. The Richland bed, or Lower Sevanee has been mined in the past, but no coal has been produced from it in late years. There are no production records of any other beds in the county, although some coal has been produced from them.2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and on l,800 tons per acre-foot of coal in place, are estimated to be 61 million short tons as of January 1, 1953. Of this total, 55 million short tons is in beds 28 inches and more thick. Areas in each bed ·were omitted from the estimate where available data relative to the bed characteristics are too meager to permit making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.3. Recoverable reserves of coal are estimated in beds 28 inches and more 'thick. This recovery is based on total thickness of coal in the bed (less partings 3/8-inch thick or more), rather than on the thickness of the coal actually mined. This thickness is about the minimum now being mined by hand loading onto conveyors in the Appalachian Region. The combined weighted average recovery for the Sewanee and Battle Creek beds in Marion County, as determined by this investigation, is 60.9 percent. Based on this, the recoverable reserves of coal in Marion County are estimated at 34 million tons."

Oct 1, 1955

By J. I. Schoenherr, G. Schubert, F. Demczenko

The currently known and used plastics and rubber recycling or sorting processes cannot be applied efficiently and economically due to large amounts of fine bulky materials (<3 mm). These wastes are mostly given to specialized landfill sites. Starting out from classical and traditional beneficiation processes a new research project was initiated to work on certain new ways to efficiently separate plastic material mixes. First basic results show that the use of new and improved thermal beneficiation methods is a great implementation in the field of plastics separation. The results can be further increased by a suitable combination with other methods as well. This leads to high-quality and almost pure separated plastics and rubber products, easy to sell on recycling product markets.

Jan 1, 2002

By K. V. Raj, C. A. Berry, A. T. Weakley, A. L. Miller, P. R. Griffiths, D. A. Parks

Diesel particulate matter (DPM) has been classified as a carcinogen to humans by the International Agency for Research on Cancer. As a result of its potential carcinogenic nature, DPM exposure is regulated by the Mine Safety and Health Administration. Currently, diesel emissions in the workplace are monitored by collecting the aerosol onto filters, which are then sent to a laboratory for thermal-optical analysis using the NIOSH method 5040. This process can take days or even weeks, and workers can potentially be exposed to excessive levels of DPM before the problem is identified. Moreover, the delay involved in getting the loaded filter to the lab inevitably means the loss of some of the more volatile organic carbon. To remedy this delay, researchers from the National Institute for Occupational Safety and Health are seeking to develop a field-portable, real-time method for measuring elemental and organic carbons in DPM aerosols. In the current study, the use of mid-infrared spectrometry was investigated. It is believed that mid-infrared spectroscopy is more suitable for use in a real-time field-portable device than thermo-optical analysis methods. This article presents a method for measuring organic carbon (OC) and elemental carbon (EC) in DPM for a broad range of OC/EC ratios. The method has been successfully applied to laboratory-generated and mine samples.

By AIME AIME

A FALL meeting that should have repercussions both in the "Transactions" and MINING AND METALLURGY was that of the Industrial Minerals Division (Nonmetallics) at Wilmington, Oct. 21-23; headquarters, Du Pont Hotel. The sixteen technical papers and two addresses were substantial and interesting. Moreover, in every instance but one, the author made the presentation, and the one exception must have been next of kin because the ensuing discussion indicated his command of the subject. The meeting schedule clicked at every turn, thanks to Dr. Gillson, chairman of the local committee, and even the four field trips adhered to the time table. The program pre-empted morning, noon, afternoon and night two general luncheons, two dinners, and an evening technical session reminding one of the Annual Meeting. Only the registration was disappointing - about 80.

Jan 1, 1943

By D. M. Hausen

Applications of process mineralogy to the exploitation of molybdenum ores begins with early exploration and continues through the evaluation of mineralized prospects, to amenability testwork and pilot plant studies, to the development of a mineable orebody and to the development of a viable process for recovery. After plant construction, a broad range of products from a wide selection of sampling locations, i.e. grinding circuit, flotation cells, smelters and roasting kilns. etc., are evaluated analytically and microscopically, followed by periodic troubleshooting of problem points. The various crystalline phases of molybdenum that occur naturally and throughout various hydrometallurgical and pyrometal1urgica1 processes are identified and characterized by a variety of instrumental methods, including XRD-XRF, optical and electron microscopy, infrared spectrographic and differential thermal analysis.

Jan 1, 1989

By W. S. Tremaine

When the Hedley Mascot mill was built in 1935, it was designed as a straight flotation plant. The ore to be treated at that time was a gold ore in which the gold was intimately associated with arsenopyrite and pyrrhotite in highly silicified and garnetized limestone gangue. This material was ground to 85 per cent minus 325 mesh in two-stage grinding and floated in standard flotation cells to produce about a 5-ounce concentrate, which was shipped to Tacoma smelter for refining. This arrangement gave us a recovery of about 89 per cent. Test work indicated that the best way to improve this recovery would be to build a cyanide plant to treat our flotation middling. Arrangements for the construction of this plant were finally approved and work on it was started in the spring of 1940. This plant was of the conventional type in which the flotation middlings were thickened, filtered, and then put through the usual cyanide process. Its capacity was 50 tons of middlings per day. This arrangement worked quite satisfactorily and gave us an increase in overall recovery of 4 per cent. Unfortunately, about the time the plant was completed, we developed, and started to ship to the mill, ore that differed entirely from that met with up to that time. Instead of being hard, it was very soft, the orebody from which- it came being much faulted and brecciated. In many sections, the sulphides were oxidized and the breccia was filled in with a very soft, hydrous iron silicate known as chloropal. When this new ore was mixed with the old ore and sent to the mill, the whole operation was disrupted. The chloropal slimed so badly that the classification, flotation circuits, and cyanide plant would not handle it. The difficulty in the cyanide plant was at the head end, where the 10 ft. by 20 ft. thickener and the 8 ft. by 8ft. drum filter would not handle the middlings containing a large percentage of primary slime and chloropal. This material would not thicken to more than 30 per cent solids in the thickener and, when pumped to the filter, would forma very thin, slimy cake. Overall recovery dropped to between 83 and 84 percent and it was quite apparent that some extensive changes would have to be made in our flow-sheet before this ore could be treated successfully.

Jan 1, 1947

By Hanry Guillén

En la Compañía Minera KOLPA, se analizó el comportamiento de sus operaciones unitarias por el período Marzo - Agosto 2016, en el cual se identificaron procesos asociados a los ciclos de perforación y voladura, bajo los términos de variabilidad NO ESTABLES NI SOSTENIBLES, los mismos que ameritaban medirlos, analizarlos, mejorarlos y controlarlos a fin de adoptar decisiones que conduzcan a operar la mina en términos de calidad y excelencia.

Sep 1, 2017