Search Documents

By K. L. Hanning

Grinding and classification circuits at Climax Molybdenum Co. are described. Since the installation of a direct digital control computer in 1974, a number of control strategies were developed and evaluated. This paper deals in particular with the practical experience and results obtained in direct digital control of a wet grinding circuit consisting of a ball mill, constant speed sump pump, and hydrocyclones. For this circuit throughput is maximized, while maintaining a desired product size. Product size is inferred from measurement of operating variables.

Jan 1, 1977

By Patrick J. Hannigan

A comparison of 40 statically and dynamically load tested piles was performed to evaluate the variation between testing methods. This evaluation indicated an agreement of 10% to 15% could be obtained when the available static resistance is fully mobilized by both methods and when time dependent capacity changes are minimized. Dynamic pile testing recommendations for minimum induced impact force, ram weight to pile weight ratio, and considerations for time dependent capacity changes are presented.

Jan 1, 1987

By Brad E. Melanson

Because mine haul trucks consume considerable quantities of fuel, they are ideal candidates for the adoption of cleaner and cheaper fuels like natural gas. Impressive fuel cost savings will be realized in regions where liquefied natural gas (LNG) has cost advantage to diesel fuel, while also providing significant reductions of air contaminants and greenhouse gases. High Pressure Direct Injection (HPDI) of natural gas utilizes the diesel cycle combustion process and therefore retains the diesel engine?s high performance and efficiency characteristics. HPDI has been demonstrated in on-road Class 8 trucks since 2001 accumulating almost 10 million kilometres to date. The supply of LNG fuel will be an essential parallel aspect in the introduction of HPDI to mining. LNG can be transported to site as diesel is today, or may be produced on or near mine operations that have access to methane sources or pipelines.

May 1, 2006

By N. Erarslan, M. Ghamgosar

The size of rock fragments depends on the nature of the loading applied the strength of the minerals and the texture of the rock. Research in the literature demonstrates that there is a distinct difference in the rock fracturing process for static and cyclic loading. The tensile strength of brittle rocks is also one of the most significant parameters influencing the rock fracturing process and the propagation of micro-fractures on the crushing, blasting and cutting of rock. The Brazilian indirect tensile test, one of the methods approved by the International Society for Rock Mechanics (ISRM), has been used to determine rock fracture behaviour under different cyclic loading modes. In this study, the dimensions of Brisbane Tuff specimens have been selected according to the method outlined by the ISRM. The main aim of this study is to evaluate the effect of cyclic loading amplitude and frequency on the Fracture Process Zone (FPZ) at the micro-, meso- and macro-scales. The post-failure behaviour of the Brisbane Tuff specimens was obtained under cyclic loading with frequencies varied from 1 to 10 Hz. The amplitude was varied from 10% of Ultimate Tensile Strength (UTS) up to 80% UTS. Laboratory investigations of rock fragment size revealed that different loading frequencies and amplitudes produce different FPZ dimensions. Multivariate Analysis of Variance (MANOVA) results demonstrated that the FPZ dimension is relatively sensitive to the frequency change. Fragment size analysis showed that the FPZ is a consequence of the initiation, propagation and coalescence of micro-fractures and depends on the nature of the loading. Laboratory evidence showed that the FPZ dimension, for the cyclic tests performed on Brisbane tuff, is ranged from 0.07 to 20 mm. The achievement of this study highlights a key finding in the understanding of fracture patterns and propagation models in the FPZ under cyclic loading, which is the dominate mechanical action in the oscillator disc cutter (ODC).

Jan 1, 2015

By B. K. Mishra

In order to maintain higher grinding efficiency in tumbling mills the mill interior and dynamics must be known. For this purpose, several different types of non-intrusive methods have been proposed and are being tried in the industry. We have made an effort to develop a diagnostic tool based on vibration signal. Here we discus results of our experiments pertaining to ball as well as SAG mill. In each case, a triaxial accelerometer was used to capture mechanical vibration generated due to the tumbling action of the charge. The vibration signal was transmitted to a remotely placed computer and the signals were analyzed by standard signal processing technique. In case of a ball mill (5m diameter), qualitative mill information could be obtained by correlating the vibration signal to feed rate and mill filling. An effort was also made to identify different motion characteristic of the charge by analyzing its vibration signal. In case of the SAG mill (10m diameter), liner wear was estimated by comparing the vibration signal emitting out of a freshly lined mill with that of a worn out mill.

Jan 1, 2011

By Zhihao Yue, Honglie Shen, Yahui Teng, Ye Jiang

"In this paper, manganous nitrate [Mn(NO3)z] was used to assist the etching of silicon wafer in hydrofluoric acid (HF) for the antireflective application, and alumina (Al2O3) layer was deposited on the surface of the etched sample by atomic layer deposition method for further antireflection. The surface morphological and compositional studies of these samples were performed by scanning electron microscopy attached with an energy-dispersive X-ray spectrometer. The surface reflectance measurements were carried out using UV-Vis-NIR spectrophotometer. Binary structures of pyramids and nanopores were obtained by etching the alkaline textured monocrystalline silicon wafer in HF and Mn(NO3)z mixed solution for not more than 15 min. But excessive increase of etching time of up to 30 min resulted in the whole destruction of pyramids. The average reflectances of the 5-min-etched sample before and after being coated with 75-nm-thick Al2O3 layer are 4.62% and 3.47% in the range of 200-1000 nm, respectively.1. IntroductionAs we know, the reflectance of silicon wafer after being sliced is so high that the maximal photoelectric conversion efficiency of silicon based solar cells is limited. Therefore, alkaline texturization process was used for silicon solar cell in industrial production. But the reflectance of this alkaline textured wafer is still greater than 10% and this process can only be used for monocrystalline silicon solar cell."

Jan 1, 2013

By Kuo En Chang

Many rare earth - transition metal (RE-TM) compounds absorb/desorb hydrogen reversibly at room temperature and atmospheric pressure. For LaNi5 which is used as a battery material, the electrochemical nature of this process is well known. In the case of Nd-Fe-B which has found wide application as a powerful permanent magnet, the absorption of hydrogen has both significant advantages and disadvantages. However, a fundamental understanding of the hydrogenation process at ambient temperatures and its effect on subsequent corrosion behavior is currently lacking. This paper reports the results of the hydrogenation of NdFeB two alloys, (NdDy)15Fe78.3A10.7B6 and (NdDy)15Fe67Co5V4A12B7, which are compared with that of LaNi5. Results show that hydrogenation can be accomplished by either electrochemical methods or immersion in dilute sulfuric acid. For the latter method, the change in lattice parameter indicates that the level of hydrogen absorbed by the NdFeB particles corresponds fairly closely to an overall composition of Nd2Fe14BH2.7. Cyclic electrochemical charge/discharge experiments show that the maximum hydrogen discharge capacities of the NdFeB, NdFeB-Co-V, and LaNi5 are 40, 60, and 210 mA?h?g-1, respectively. Anodic potentiodynamic polarization measurements and calculated values of icon reveal that absorbed hydrogen in NdFeB-Co-V and the NdFeB may lead to significant increases in corrosion rates.

Jan 1, 1995

By Lightfoot. Nicholas, Na Liu

"Mining in multi-seam workings has been undertaken for many years in the VK Remnant pillars above and/or below current working areas have an important influence on retreat gateroad conditions at five of the remaining six deep coal mines. These interaction effects need lo be predicted ahead of mining so that longwall panels can be positioned to minimize roadway damage and to identify areas where additional support should be installed early into competent strata when and where it is most effective.Currently, three-dimensional elastic stress analysis using MAP3D is undertaken to predict local vertical and horizontal stress magnitudes during gateroad development and in front of the face on retreat. The predicted stress fields are often used as input to FLAC for roadway modelling.Using Maltby Colliery in South Yorkshire as a case study, this paper illustrates the MAP3D approach, together with its current limitations and uncertainties. Possible future improvements in the analysis method are proposed and the authors would welcome comments on these, or suggestions for alternative approaches.MODELLING OF MULTl-SEAM LAYOUT & MULTI-SEAM INTERACTIONThe remaining large coal mines in the UK arc operating at depths of 800-1, 150 m (2,625-3,773 ft). Production panels are now mined on retreat after the accompanying single entry access roadways have been completed. These gateroads are typically supported with a system of steel rock bolts and cable in the roof and steel bolts and glass re in forced polymer (G RP) dowels in the sidewalls.In addition to new panels being mined in the vicinity of old goafed districts, a significant amount of extraction has usually already taken place in coal seams above and/or below the current working areas. This means that there is also interaction between the current workings and the remnants of the old workings in other seams. As a consequence of the mining methods employed, old workings can have a complex geometry compri ing collapsed and partially collapsed excavations intersper ed with small and large pillars of unmined coal. The unmined coal pillar act as stress concentrators that carry the overburden load while the mined out excavations create stress shadows of varying degrees depending on how much collap e and reconsolidat ion has occurred. This is illustrated by a simple elastic model as shown in Figure I."

Jan 1, 2010

By Newell H. Orr

Titanium's performance characteristics in acidic oxidizing and mildly reducing environments make it applicable to numerous currently defined and many projected hydrometallurgical applications. With titanium's current and projected availability and price stability increased use in pressure leach, piping systems and electrorefining is practical.

Jan 1, 1983

By J. B. Yianatos, F. A. Contreras

Mineral carrying rates across the pulp-froth interface in the range of 1.4-3.2 tph/m2 and bubble surface coverages between 7 and 22 %, have been determined in large rougher flotation cells operated under normal conditions. To evaluate these variables, measurements of bubble size distribution, bubble load and size distribution of particles collected by true flotation, were performed at different concentrators. A model for estimating the bubble surface coverage at the pulp-froth interface level as a function of bubble load, Sauter mean bubble diameter and particle size distribution of the mineral collected by true flotation, was developed. Bubble loadings in the range 24-70 kg/m3, bubble sizes between 1.5 and 3.2 mm and superficial gas rates between 1.2 and 2.0 emfs, were measured in copper rougher flotation cells under normal operating conditions. Estimated bubble surface area fluxes were in the range 31 to 62 cm2/s/cm2- Results of carrying rates and bubble surface coverage, at the pulp-froth interface, were significantly lower than the maximum carrying rate for the collection zone, indicating that in this case is difficult to achieve maximum carrying rate at the pulp-froth interface level. The main constraints regarding carrying capacity limitations are then related to the froth transport characteristics (i.e. cell design, froth residence time, froth stability, froth recovery). Advances in Mineral Processing Science and Technology Proceedings of the 48th Annual Conference of Metallurgists ofCIM Sudbury, Ontario, Canada Edited by

Jan 1, 2009

By T. C. -M. Cheng

Iron removal and disposal in zinc plants has imposed a major environmental challenge to the industry. Among the existing options of precipitating iron as jarosite, goethite, and hematite, the Hematite Process seems to be the best candidate for the future development of a waste-free technology, because of its potential of producing saleable iron oxide residues for feed in iron-steel making industry. Unfortunately, under the current practice of the Hematite Process, it is not possible to produce iron residues clean enough to meet the specifications of the said industry. In this paper, the practice of industrial hematite precipitation and the relevant technical literature are reviewed with the objective to identify the critical processing parameters which are responsible for the contamination of hematite, particularly with sulfur and zinc. The analysis is conducted from a crystallization theory standpoint with emphasis given to the role of supersaturation with respect to the cleanliness of hematite precipitates.

Jan 1, 1997

By József Faitli, Barnabás Csoke, Károly Solymár, Zoltán Hatvani, Dimitri Papanastassiou

"Grinding has a significant economic impact on ore dressing/processing, therefore the sizing of mills has an outstanding role.In most cases, the sizing of dry or wet mills for ore processing is primarily based on the determination of the Bond grindability index, using the Bond-Kjos-Rowland relations. In several cases, grinding takes place under conditions different from these and the grinding conditions have a great influence on the post-grinding process. This is particularly true for the grinding of bauxites where grinding takes place in alkali, often in higher temperature (up to 100 ºC) in alkali Liquor. So it is necessary to develop a testing method providing a reliable grindability index even under these special circumstances (grinding in alkalis medium at different temperatures) and allowing a more precise mill sizing. The new heated mill is suitable to determine the grindability index under temperature-controlled circumstances, in liquids with different temperatures (water, alkali). This paper presents in detail the equipment, the conditions (parameters) of the testing process for wet and alkaline grinding, the measuring results and the conclusions."

Jan 1, 2003

By A. V. Tarasov, V. M. Paretsky

"The knowledge of the true phase composition of the liquid slag is a very important problem, mastering of which grants the possibilities for the scientifically founded choosing of the decoppering method of the autogenous smelting slags. The investigation using different methods of the phase composition of the flash quenched autogenous copper melt's slags has shown, that the most effective method of the slags' decoppering during smelting with the white matte production is the flotation of the recrystallized slags. In this work the authors posed the problem to realize the slags quenching with the rates similar to those, which are used in the modem investigations devoted to the flash quenching of the ironcontaining alloys, with the subsequent study of the quenched samples using the Mossbauer spectroscopy methods in order to establish the connection between the liquid slag's structure and the metals losses with the slag."

Jan 1, 2000

By Lon Santis, Michael Swisdak, John Tatom

The Institute of Makers of Explosives (IME) and A-P-T Research, Inc. (APT) have developed a quantitative risk assessment tool called IMESAFR (IME Safety Analysis for Risk) for managing risk from various activities undertaken in the commercial explosives industry. The first version was completed in 2006 and Version 2.0 of the software was completed in 2012, incorporating several major new features. The platform is now based on a Geographic Information System (GIS), providing a bird’s-eye-view to help visualize facility layouts and risk. Spatial data on potential explosion sites and exposed sites can now be automatically transferred from the images to ease users’ data input. Use of GIS data provides the ability to check facility compliance with quantity-distance (QD) standards such as the American Table of Distances (used by the Bureau of Alcohol, Tobacco, Firearms and Explosives, ATF), the NATO standard (used by Natural Resources Canada and other nations), or a user-defined table. Research conducted and knowledge gained over the last 10 years enabled changes in the algorithms and models that provide greater fidelity and reduce conservatism. Expert users can change global settings to more accurately match actual site conditions and the program runs using either Imperial (English) or SI (metric) units of measure. These changes and other new features are discussed and demonstrated.

Jan 1, 2013

By S. J. Neethling

"Liberation is a key driver in all mineral separation processes as it limits the maximum possible grade for a given recovery. In flotation, this is further complicated by the fact that it is surface exposure of the floatable minerals that determines the ultimate performance. Liberation, grade and surface exposure are commonly quantified using Scanning Electron Microscopy coupled to Energy Dispersive X-ray spectroscopy (SEM/EDX) analysis of polished sections. The intrinsically 2D nature of this technique can result in significant sampling errors and stereological effects that can affect the quantification of the ore’s textural characteristics. X-ray micro-Tomography (XMT) is an imaging method that can non-invasively and non-destructively delineate ore fragments in 3D, thus providing an alternative method that eliminates the need for stereological corrections and readily provides surface exposure. A methodology and automated algorithm were designed for extracting this information from images of closely packed particles, thus allowing samples containing a large number of particles to be assessed.The main drawback of XMT is that, unlike SEM/EDX, it cannot directly measure the mineralogy of the sample, instead producing a 3D X-ray attenuation map. We therefore also present an algorithm for calibrating the thresholding of the XMT images based on SEM/EDX images of sections through the same sample, thus allowing the liberation analysis to be carried out on a 3D mineral map in which the uncertainty in the mineral assignment is small and statistically quantified.The methodology was tested on low grade porphyry copper ore as this is both an industrially relevant and traditionally difficult system to quantify using XMT due to the similarity in the X-ray attenuation of the sulphide species, especially the pyrite and chalcopyrite. As each 3D volume imaged contain 100-1000s of grains, large data sets can be readily produced. By dividing these particles into classes based on both their surface exposure and grade, the extent to which there is preferential breakage of the particles can be assessed—an important consideration if sufficient surface liberation for good flotation performance is to be achieved at coarser particle sizes. It is also shown that erroneous conclusions can be drawn when basing the analysis on 2D sections through the particles."

Jan 1, 2018

By Bing Li, Miao Shen, Qiang Wang, Yuqi Chen

Electrochemical methods including cyclic voltammograms, square wave voltammograms, chronopotentiometry are applied to characterize the reduction potentials of Na+ and Li+ ions in LiCl-KCl melts. According to theoretical calculation, the reduction potential for Na+ is slightly more negative than Li+ in NaCl-LiCl-KCl melts at 450℃. However, by electrochemical measurements, the reduction potential of Na+ is slightly more positive than Li+ in the above melt and the potential difference between Na+ and Li+ reaches 0.16-0.2V on an inert W electrode in 1.0-2.0 wt% NaCl-LiCl-KCl melts. An active Pb electrode is used to improve the removal rate of Na+ from LiCl-KCl melts. The reduction potentials for both Na+ ions and Li+ ions on a Pb electrode shift to more positive values and the reduction currents become larger. After 6h electrolysis on a Pb electrode at -3.0V, the practical removal efficiency of Na+ ions reaches 90.12% and the reduced products contain metallic Na and Li with a Na/Li mass ratio of 4.25/1.

Jan 1, 2015

By Noel N. Moebs

Five LANDSAT lineaments in the coal mining region of southwestern Pennsylvania were investigated by the Bureau of Mines to determine their geologic character, relation to subsurface conditions, and the means of discriminating one from another. The investigation included earth resistivity and very low frequency (VLF) electromagnetic traverses, soil moisture sampling, and a correlation with coal mine roof conditions. The lineaments could not be detected by the methods used, suggesting that they might be a surface phenomenon unrelated to subsurface geologic structures or roof stability in coal mine workings beneath.

Jan 1, 1987

By R Burgess-Limerick, J Haight

A review of mining automation experiences was undertaken on behalf of the National Institute for Occupational Safety and Health (NIOSH). The research included a review of literature and guidance materials; analysis of automation related incidents and visits to surface and underground mines in Australia, Brazil, Chile, South Africa, Sweden and the USA.

Apr 16, 2024

By Frank L. Marley

Mexican silver mining operations have existed prior to the sixteenth century. Recovery processes throughout the centuries were developed at the many mining localities and have progressed through smelting, the patio amalgamation process to cyanidation and flotation. A study of the present silver mining zones is reported in which the ores are evaluated in terms of the mineralogical constituents, their state in the matrix and the effects these are noted to impose upon the efficiency of recovery. Silver mineral identifications were by quantitative ore microscopic and scanning electron microscopic energy dispersive X-ray analysis.

Jan 1, 1982

By Y. K. Yen, J. D. Miller, C. L. Lin

The image-based On-line Particle Size Analyzer (OPSA)system has been developed at the University of Utah to measure particle size distributions under plant conditions where overlapped and segregated particles are being transported on a moving belt conveyor. Evaluation of the OPSA system at several plant sites has been completed. The results show a consistent agreement between the particle size distributions obtained from the OPSA system and those obtained from laboratory screen analysis of belt samples. These results and the stable performance of the OPSA system during the field tests suggest that continuous quality control of crushed products is possible using the OPSA system.

Jan 1, 1999