Search Documents

By Kot F. Unrug

Strength of coal is one of the governing factors in size determination of mine pillars, and therefore affects the percentage of extraction and thus, utilization of reserves. Coal strength is also important from the subsidence control standpoint, where mine pillars with appropriate safety factors should be designed for long term stability. Determination of coal seam strength has been addressed through the extrapolation of the coal strength obtained from a small number of samples on the whole section of the seam. This procedure often gives unreliable results. Presented in this paper is a method of in-situ strength testing of coal, allowing for a realistic determination of seam strength. Results of a field case study dealing with the coal seam, where samples for the laboratory strength tests could not be obtained due to the dense cleat, are presented. However, in these conditions, the in-situ testing was successful. A comparison of both conventional and the in-situ penetrometer method was carried out. It was found that the penetrometer data not only improve the accuracy of strength determination of the entire seam, but also prove to be much more cost effective than the conventional method on a per test basis.

Jan 1, 1995

By J. McMurray

Introduction Uranium was recovered from mining of collapse breccia pipe deposits in the Arizona Strip district in northwestern Arizona (Figure 1) intermittently between 1956 and 1990, with cumulative production having totaled 23.3 million pounds of U3O8 (8960 tU) at an average grade of 0.6% U3O8. Production was suspended in 1990 because of low uranium prices, but the recent resurgence in market price once again makes the breccia pipe deposits potentially attractive exploration and development targets. This paper describes: (1) formation of the pipe structures and their metallogenesis; (2) mining and milling of breccia ore; and (3) potential roadblocks to development of new breccia pipe mines. Breccia Pipe Formation Formation of the breccia pipes began in cave systems formed during development of karst topography in the Mississippian Redwall Limestone. The karst Redwall surface was eventually covered by up to 900 meters of shallow marine to continental sediments ranging in age from Pennsylvanian to Triassic. The pipes were formed by progressive upward stoping caused by groundwater ascending under hydraulic head along near-vertical faults, joints and fractures. The stoping process involved both chemical disaggregation and mechanical failure of roof and wall rock. Upward stoping of successively younger units allowed for upward propagation of a pipe and resulted in a chimney-like column of breccia between the steep walls of the pipe. Syndepositional thickening of sedimentary units of varying ages indicates that pipe formation began as early as early Pennsylvanian time and continued intermittently through Triassic time.

Jan 1, 2007

By P. Jonsén

Understanding mill charge motion is important. In the charge, the centre of gravity is shifted from the rotational centre of the mill system, and its motion is induced by rotation of the mill, while at the same time the charge creates a torque into the mill system. Breakage of ore particles and wear of liners/ball media are closely linked to the motion. To study these phenomena in a physically correct manner, numerical models for different parts of the mill system are needed. Validations of such models are scarce, because of the difficulty to measure in a tumbling mill. Experimental measurements in a lab mill were done for diverse load cases: varying feed materials, mill fillings, mill speeds and pulp liquids. The mill is set up to directly measure the charge-induced torque. The accuracy is good with relative uncertainty smaller than ±2% for relevant load cases. A full three dimensional numerical model of the whole mill is used to predict induced torque. Agreement between predicted and measured torque at steady-state is good. In addition, the model can accurately predict the mill start-up behavior for torque and mill power. This proves that the model is physically correct, and can be used for full-scale mills.

Feb 27, 2013

By Omotayo Kalejaiye

The Siwek 20-L chamber is widely used throughout the world to evaluate the explosibility of dusts. This research evaluated the quality of dust dispersion in the Siwek 20-L chamber using Pittsburgh coal, Gilsonite, and purple K dusts. A Pittsburgh Research Laboratory (PRL) optical dust probe was used to measure optical transmittance through the dust cloud at various locations within the chamber. A total of 540 tests were performed, with triplicate tests at five nominal dust concentrations and six locations. The two standard dispersion nozzles (rebound and perforated annular nozzle) were compared. The transmissions corresponding to the normal ignition delay period were used to: (a) determine variations in spatial uniformity of dispersion obtained with both nozzles; (b) make comparisons between the experimental transmission data and those calculated from theory for the three dusts; and (c) make comparisons with transmission data measured in the PRL 20-L and Fike 1-m3 dust explosion chambers. The uniformity of dispersion for the three dusts was similar with both nozzles, despite the differences in nozzle geometry and mode of operation. Transmission data of the three dusts were all significantly lower than those calculated from theory. This was discovered to be, in part, due to significant reduction in particle size that occurred during dispersion. By measuring particle sizes before and after dispersion, values of 60%, 50%, and 20% reduction in particle size (based on the surface-weighted mean diameter) were obtained for Pittsburgh coal, Gilsonite, and purple K, respectively. Transmission data from the PRL 20-L, Fike 1-m3 and the Siwek 20-L chambers indicated comparable results in terms of uniformity of dispersion. However, transmission data from the Siwek 20-L chamber were significantly lower than those of the PRL and Fike chambers. Again, this was attributed, in part, to the significant reduction in particle size that occurred during dispersion in the Siwek chamber. The design of the outlet (dispersion) valve of the Siwek 20-L apparatus charge vessel was largely responsible for the particle break-up. The contribution to particle break-up by the dispersion nozzles and the high level of turbulence in the chamber were found to be minimal. This is a significant finding in that the dust particle size tested for explosibility in the Siwek chamber is considerably smaller than the original dust sample.

Jan 1, 2010

By P. Sanchez-Mejorada

GEOLOGISTS who are acquainted with the mines of northeastern Mexico realize that the most important lead-silver replacement deposits of the province are confined to a single formation. But since the formation is several hundred meters thick, the author has determined the relative position of the lead mantos in the belief that this information will prove useful in the search for new mines. This article describes the stratigraphic location of lead-silver replacement deposits known in several mines situated in a region comprising part of the states of Coahuila and Nuevo Leon. The area studied extends for 200 km* (125 miles) from east to west and 70 km (45 miles) north to south. Metallogenic Province: The most important metallic deposits of the region have the following common characteristics: 1) The orebodies occur as manto replacements of calcareous sediments. 2) The horizons that have contributed large tonnages of ore are in similar positions in the corresponding stratigraphic columns (as it will be shown later on). 3) Lead is the most important metal in the ores. Silver is commonly present in small amounts. Occurrence of zinc is dependent on the degree of oxidation of the primary sulfides. 4) A large proportion of the total production has been in the form of oxidized ores. 5) The deposits are located on anticlines. Rocks of Cretaceous age crop out over large areas of the states of Nuevo Leon and Coahuila. forming part of a belt that extends to the south along the eastern Sierra Madre. The sediments are cut by a small number of intrusive stocks ranging in characteristics from rhyolite to diorite. The most prominent structural feature of the region is a series of folds trending northwest-southeast. Faulting is not conspicuous in the region, although a major fault zone is found farther East.' The physiography closely reflects structural features, with mountains formed by anticlines and valleys conforming with intermediate synclines. Narrow valleys have also been developed along the axes of many anticlines, where solution of limy sedi- ments and erosion have proceeded along axial tension fractures. Stratigraphy: Rocks of the Upper Cretaceous are exposed in only a small percentage of the total area. Generally they have been eroded away from the mountains and are covered by recent talus and alluvium in the valleys. Humphrey' has published an excellent paper describing the Cretaceous formations of the Sierra de los Muertos, a short distance west of Monterrey. A brief summary of these formations is given below to convey an overall picture of the stratigraphic sequence that prevails just south of the area under consideration. Upper Cretaceous Indidura: Essentially thin shaly sediments. Cuesta del Cura: Limestone in thin wavy beds

Jan 1, 1959

By G Fakes

This paper describes the history of civil engineering tunnelling and developments in soft ground techniques during the 19th and 20th centuries, culminating in the design and use of high speed tunnelling machines for all types of ground conditions. Some of the problems encountered are outlined, and descriptions are given of some contemporary developments in rock tunnelling techniques, with comparisons of methods used in the mining industry.

Jan 5, 1996

By R. L. Miller

"Why should we care about diesel quality amidst the complexity of mining for minerals? Mining companies use a large amount of diesel fuel in their worldwide operations, both for moving ore from the mine to the processing mills or transportation hubs, and to generate power for onsite processing. This creates a large carbon footprint and poses both environmental risk with the production of emissions, and public perception of how those companies do their business as stewards of the environment while incurring a huge fuel expenditure. To improve diesel quality and create incremental value and greater environmental stewardship, the opportunity is broken down into several segments: 1. Mining industry diesel consumption 2. Fuel quality issues 3. Impacts on operations, economics, and emissions 4. Potential solutions 5. How improved fuel quality saves fuel expenditures 6. Economics of improved fuel quality 7. Recommended testing process 8. Fuel quality analysis checklist MINING INDUSTRY DIESEL CONSUMPTION The average grade of mined Australian ore bodies has halved, while the waste removed to access the minerals has more than doubled over the last 30 years, thus increasing energy consumption by 70%, (http://eex.gov.au/industry-sectors/mining/). Energy consumption and intensity in mining and mineral processing is rising at around 6% per annum. The mining industry is a huge consumer of diesel fuel worldwide, and the SRS Rocco Report of 4 August 2014 gives a better picture of recent trends. To better understand the reasons to reduce both fuel costs and consumption, we need to compare metrics on the amount of diesel consumed per each ounce of gold produced over the last decade. The rate of diesel consumption in gallons per each ounce of gold produced for the top five worldwide gold producers has doubled in the last 8 years from 12.7 gallons per ounce in 2005 to 25.8 in 2013 as shown in Figure 1 below.This is caused by 1) lower ore grades requiring more hauls to get same amount of finished gold product, and 2) haul trucks moving ore from deeper sources in open pit and underground mines. For one large multi-national gold mining company, the 2005 waste rock / production ratio was 52 metric tons/gold ounce; by 2013 that ratio had grown to 113 metric tons/gold ounce per the same SRSrocco 4 August 2014 report. Using the metrics above, the top 5 gold miners used over 591 million gallons of diesel fuel in 2013. The cost of diesel in dollars per ounce of gold has increased from $30.48 in 2005 to $101.14 in 2013, an annual appreciation of 16.2% as shown in Figure 2 below."

Jan 1, 2017

By David F. Gearhart

A cooperative study was conducted between Signal Peak Energy and the National Institute for Occupational Safety and Health (NIOSH) to evaluate the behavior of a pre-driven recovery room under less than 200 ft of cover. The design of the support systems for a pre-driven recovery room must provide control of the roof and ribs during the changing stress environment experienced throughout the final advance of the longwall into the recovery room. It must also provide a stable area where mine personnel are not exposed to undue hazards during shield recovery operations. This recovery room was constructed in two phases; each phase mined a 21-ft-wide room that was heavily supported, and subsequently fully backfilled with 800-psi, cellular concrete. Instrumentation to monitor the recovery room performance included borehole pressure cells (BPCs) placed in the head gate and tailgate pillars, at four locations across the longwall panel, in the fill material, and in the first row of outby pillars near the center of the panel. Four roof-to-floor convergence sensors were installed in the back fill material and a vertical, multipoint borehole extensometer (MPBX) measured the displacement of the strata above the recovery room. Surface surveys were conducted to measure MPBX collar movement. The data show that the front abutment load was transferred onto the recovery room backfill and the out by pillars as the longwall panel was extracted. As the longwall approached the recovery area, the fender and shields yielded, but the backfill provided enough support to keep the room stable as the longwall advanced to its final position. The system worked as planned and the face was recovered in record time.

Jan 1, 2014

By Hong Nguen Vu, Pavla Ovcarí, Peter Fecko, Barbara Tora

The aim of this paper is to evaluate the suitability of a coal sample from the mine Jaworzno (Poland)- locality for bacterial leaching. Laboratory research used a pure bacterial culture of Thiobacillus ferrooxidans. The results showed that bacterial leaching was effective, with a one month leaching time, when 65% of total sulphur and 85% of pyritic sulphur was leached. The paper describes changes to the pyrite during and after bacterial leaching.

Jan 1, 2003

By T. McCallum, C. Cooper, B. Hutzler

"In copper solvent extraction, managing the quality of the organic phase is a key parameter to ensure optimal physical and metallurgical performance in the plant. Increased throughput as a result of declining ore grades coupled with advances in plant design and practice, resulting in reduced organic losses, has pushed the limits of the status quo with respect to organic quality. Clay treatment of plant and recovered organic at the optimal dosage is critical in maintaining quality, however, achieving the optimal dosage through existing filtration capacity and practice can be difficult. Cytec has developed a process aid that increases efficiency of existing filtration equipment that has been successfully implemented at two commercial SX operations. ACORGA® CB1000 enables higher dosages of clay while allowing for more efficient use of existing filtration capacity. This study analyzes results from commercial trials and demonstrates that improved organic quality and clarity is achievable through optimization of current treatment practices. INTRODUCTION Decreasing ore grades have prompted copper solvent extraction operations to raise PLS flow rates, increasing plant throughput to maintain production1. The ability to process higher flow rates through existing mixer-settlers historically came at the expense of increased entrainments2. However, advances in mixer-settler design, practices and improvements in organic recovery processes have enabled operations to maintain, and in some cases reduce organic losses while achieving higher flow rates through existing equipment. Based on the increased demand on the SX equipment and reduced losses (or more efficient recovery) maintenance of the circuit organic quality through efficient clay treatment is now more important than ever. This paper discusses common industry practices and related issues in organic clay treatment, and presents benefits achieved in commercial operations through the use of ACORGA® CB1000 Clay Binder. IMPROVEMENTS IN DESIGN AND PLANT PRACTICE Mixer-settler design has improved since the first commercial copper SX operation in the late 1960s. Advanced designs in mixer, settler, and settler internals have contributed to reductions in entrainments. For example, improved impeller designs have been reported to decrease organic in aqueous entrainment from the ‘old designs’ of 50-200 ppm3 to as low as 4 – 10 ppm confirmed via diluent and reagent consumptions . Similarly, operations are reporting a 20-50% decrease in reagent consumption when compared to the original design criteria3. Operations have optimized settler internals to increase coalescence and have improved settler operating practices which have been shown to reduce entrainments7. Comparison of the SX world operating data from 1999 and 2007 shows reductions in organic entrainment losses with increases in flow rates."

Jan 1, 2015

By Zhang Chuanfu, Li Shixiong

"In the electrolysis electrodeposition or electroplating of aqueous solution of copper, lead, zinc, nickel, manganese etc, with the increase in cathodic over potential the reducing rate of metal and the cathodic current efficiency increases and the deposit becomes more compact and smooth. According to this principle, a method and equipment of the auto-control of electrolyte quality is invented. The industrial application shows that this method turns the experienced operation into auto-control. The quality and quantity of metal is improved greatly and the consumption of electric energy is reduced.In the electrolysis, electrodeposition or electroplating of aqueous solution of copper, lead, zinc, nickel, manganese etc, usually organic additives are added according to the state of cathodic deposit according to experience. This traditional and experienced operation, often lead to that the quality of additive is not optimum which affects the quality and quantity of metal and increases the consumption of electric energy. To counter the controlling problem of the quantity of additive, the authors have invented a corresponding equipment of the auto-control of electrolyte quality [1], it has found application in industrial practice."

Jan 1, 2000

By G. Van Weert

Mining project feasibility is projected from a geological model and a mining plan. Ore grade is assumed to be continuous, based on drill hole assays as much as 80 m apart. Eighty meter is 80,000,000 micron. Base metal concentrators may be said to work at 80 micron, for flotation at least. In short, metallurgical and financial performance in green field metal mining is forecast on rejecting waste after comminuting the ore down by roughly a volume factor of 1,000,000,000,000,000,000 (1018) from the feasibility/banking study parameters. This is the gap between mine and mill, between present sulphide mining practices and mineral dressing capabilities, and ultimately between lenders/shareholders expectations and mine/mill performance. By inserting a new upgrading technology in this gap, new opportunities for reserve enhancement and cost reduction are created, and risk could be reduced. Blast holes for extracting the outlined ore might be 8 m apart. Most ore bodies do not abruptly change composition at 8 m intervals; nor are they homogeneous in grade at the 8 cm (3?) rock size, optimum size for sorting. Mining in 8 m blocks will inevitably cause dilution of the mill feed and ore losses in the waste rock. This is well recognized in the mining industry. Much work is going on applying the vast data storage and manipulation capability of computers to mine scheduling. One only has to consult the SME Annual Meeting presentations. At the 2007 Meeting, Clark and Dagdelen described the challenges faced by Newmont at its operations and the application of sophisticated software tools and methods in its search of solutions to mining optimization. Block models can often contain in excess of one million blocks. Additional complexity exists when multiple grades are modeled for each block. The authors identify the main optimization problem as the system?s ability to cater to large scale problems in an acceptable timeframe; in other words, still larger computers are needed. At the same Meeting, Menabde et al (2007) presented a new pit development planning tool called Blasor, developed by BHP Billiton Technology, and its co-developed Blasor IPD (In Pit Dumping), (Zuckerberg et al (2007)). For purposes of this paper, Blasor/IPD incorporates options on processing capacity constraints and blending targets, eliminating arbitrary up-front decisions about cutoff grades for each block of material in the extraction sequence.

Jan 1, 2008

By Pierre Pelletier, Christian Pichetie, Dany Pelletier

"IntroductionDuring 1994, Barrick Gold Corporation, or American Barrick at that period, acquired Lac Minerals Ltd. properties. One of them was the Bousquet Complex. The Bousquet Complex is divided into three distinct sites: one mine (Bousquet 2), one mill (Est-Malartic Division) and one analytical chemistry laboratory (Les Terrains auriferes).The Bousquet 2 orebody was discovered in 1986. An extensive drilling program was initiated during 1987. Its purpose was to define the orebody extent. At the end of 1997, gold production from Bousquet 2 mine reached 1 290 000 oz of gold from a cumulative tonnage processed of 4 175 000 M t.From 1980 to 1990, the Est-Malartic mill was used for the treatment of ore from the following mines: Bousquet 1, Doyon, Francoeur (Richmont mines), Buckshot and 1-20 stope. At present, the mill receives ore from the Bousquet 2 mine.HistoryThe Est-Malartic mill is located close to the town of Malartic in northwestern Quebec. The mill has been in production since the mid-1930s processing mainly clean, free mill gold ore. Active mining from the Est-Malartic mine ceased in 1979 and the mill was switched to custom processing of ore from La Mine Doyon located some 45 km to the west. This custom processing arrangement continued until 1987 when the expanded mill at Doyon became available to process all of the Doyon production. In 1987, Lac Minerals commenced development of a second mine at the Bousquet site located 40 km west of Malartic. This mine, Bousquet 2, is the down dip extension of the La Ronde mine developed by Agnico Eagle. During pre-feasibility evaluations, it was determined that it would be economically more attractive to modify the existing Est-Malartic mill than building a new facility on site. The Est-Malartic mill modifications for processing the high-copper/gold ore from the Bousquet 2 mine began in late 1989 and new circuits were commissioned in mid-1990. Modifications included the addition of both gravity and flotation concentration circuits to recover coarse, free gold and the copper. The existing leaching circuit continued to operate on the copper flotation tailings with some minor modifications to the solution handling systems. A S02/Air cyanide destruction circuit was also added at that time."

Jan 1, 2000

By Robert Stefanko

Transients are results of sudden changes which take place in power systems and can be created by the opening and closing of switches and circuit breakers or the occurrence of a fault anywhere in the complex. Transients are of short duration, and the time during which they occur is an extremely small percentage of the total operating time. However, it is during these short periods that the greatest electrical stresses occur, mainly due to excessive currents or voltages. In extreme cases, system parts are damaged, and equipment failure follows. Safety can be further compromised because anomalous voltages can exist at machine frames. For several years, the electric utilities have been well aware of the serious nature of transients on their systems, but problems firmly believed to directly result from these phenomena are just now becoming apparent to the coal mining industry. The situation became discernible after the underground introduction of high voltage distribution systems (along with vacuum circuit breakers) and sensitive solid state electronic apparatus. In order to protect against such transients, knowledge about their characteristics and origin must be obtained.

Jan 1, 1974

By Stefan Swartling, Rudy Lyon, Donald A. Bruce

"Since their first production application in Sweden in 1995, water-powered, down-thehole hammers (WDTH) have been used throughout the world in many different drilling applications, total lines, over 25 million lineal meters of drill hole. This paper reviews the history and principles of down-the-hole drilling (DTH) in general with both air and water, before focusing on the details of WDTH hammers. A summary of the numerous and considerable advantages of WDTH drilling is provided, with particular emphasis on their superior productivity, smaller deviation, applicability in sensitive/urban conditions, environmental protection and much reduced energy requirements.HISTORICAL PERSPECTIVE ON PRODUCTION DRILLING METHODSAir-flushed drilling with top hammers began in the mining industry in Sweden in 1873, while down-the-hole (DTH) drills, again with air flush (and activation) became operational in 1950. During that same time interval, Simon Ingersoll had patented the first steam-powered, top hammer rock drill to provide higher productivity in blast hole drilling. It is well known that water, as an activating, flushing and cooling medium, has many significant advantages over the use of air. However, it was not until 1973 that top hammer systems (either air or hydraulically activated) for larger rigs were adapted to the use of water flush, typically via “under the head” swivels.The concept of a water-powered, down-the-hammer (WDTH) had been explored prior to G. Drill acquiring the original patent from Atlas Copco in 1988. LKAB, a huge underground mining company owned by the Swedish Government and providing about 90% of the European Union’s iron ore, purchased G. Drill in 1991 and encouraged the commercial development of the WDTH. The first full-scale WDTH production works were carried out for LKAB in 1995, since when over 25 million lineal meters of drilling have been recorded in both underground and surface applications.In 2001, G-Drill was renamed Wassara, which today still holds the worldwide patents for WDTH technology. Regarding North American usage, the first significant application was by Advanced Construction Techniques (ACT) Ltd. during the test grouting program conducted for the U.S. Army Corps of Engineers at McCook Reservoir, Chicago, in 2002. Since then, WDTH has become the tool of choice for specialty drilling and grouting contractors on dams and other major structures throughout the U.S."

Jan 1, 2015

By R. Zhang, S. Azam, S. Liu, J. H. Golbeck, V. Kurashov, S. Bhattacharyya

Free radicals (FRs) present in coal dust directly influence the interaction behavior between lung cells and dust particles. FRs are atoms or groups containing unpaired electrons, with strong chemical reactivity and a short lifespan. FRs which are quite persistent in natural environments, termed environmentally persistent free radicals (EPFRs), have recently received much attention as new environmentally hazardous substances. EPFRs present on coal dust serves as an active intermediary to catalyze reactive oxygen species (ROS) production by oxygen molecules endangering mine workers’ health. Many EPFR species may be bonded to the particle surface or trapped within the particle during coalification and can be modified with progressive size reduction through cutting at the mining face or crushing/pulverization in the plant. This study measured EPFRs for lignite, sub-bituminous, and anthracite coal dust at various sizes. We especially focused on EPFRs for submicron coal dust prepared by cryogenic methods. The outcome of this study will directly improve the free radical-dependent toxicity quantification and ultimately contribute to the size-dependent coal dust toxicity quantification.

Mar 2, 2022

By J. M. D. Wilson

The literature relating to binders in iron ore pelletizing is reviewed from the point of view of their established or proposed bonding mechanisms in green and dry pellets.

Jan 1, 1981

By Turcotte. Yves-Laurent

Notre conférencier, Monsieur Yves L. Turcotte, Vice-président et Directeur général chez Promaintech Novaxa est diplômé en génie industriel de l?Université du Québec à Trois-Rivières et détient une maîtrise en gestion de projets de l?Université du Québec à Montréal. Il est une véritable sommité canadienne dans le domaine de l?amélioration de la performance des organisations. Provenant d'entreprises manufacturières et de services, il possède plus de 20 ans d?expérience en tant que développeur de technologies, conseiller et formateur auprès d?entreprises. Il a à son actif la réalisation de mandats dans plus de 400 entreprises. Il est reconnu pour sa grande capacité d?analyse et pour trouver des solutions novatrices et profitables aux problèmes des organisations les plus complexes. Aujourd'hui, il dirige Promaintech Novaxa, une division de DMR, qui a célébré son dixième anniversaire en 2006. Cette organisation ayant des places d?affaires dans la région de Montréal, Québec et Vancouver compte plus de 50 professionnels et a une carte de visite dans 16 pays. Les axes d?intervention sont le Management, la Productivité, la Fiabilité, l?Innovation et l?Amélioration Continue.

Feb 1, 2008

By H. Rumfelt

Strip mining in the domestic coal industry is contributing a greater proportion bf overall production than at any time in the past. U.S. Bureau of Mines statistics show that the percentage of total production mined in 1958 by stripping methods increased to more than 30 pct, up from 22 pct in 1951. The tendency to favor strip and open pit mining exists in other mining activities, but such trends are not as clearly outlined as in the coal industry. Significantly, the depth of overburden in coal properties considered suitable for stripping is also increasing. A depth of 50 to 60 ft of overburden was once considered to be about the maximum amount that could be handled economically. Today, a depth of 80 to 100 ft is frequently taken into consideration for simple overcasting operations (i.e., excavating overburden and dumping it in the spoil position where it remains indefinitely).

Jan 5, 1961

By S. N. McIntosh

Column bioleaching was evaluated by the U.S. Bureau of Mines as a means of recovering manganese from a low-grade ore from the Three Kids deposit in Southern Nevada. Manganese was solubilized from the ore using indigenous heterotrophic microorganisms. Diluted molasses medium was provided as nutrient for the microorganisms. The medium was recirculated through the ore bed until the sugars were spent. Two methods were evaluated to recover manganese from the sugar depleted bioleaching solution: (1) adsorption with a weak cation exchange resin followed by stripping and precipitation techniques, and (2) direct precipitation of the manganese using ammonium carbonate. Both methods removed up to 95 pct of the solubilized manganese from the medium as a carbonate salt. After manganese removal, the medium was replenished with fresh molasses and recycled back through the column. More manganese was effectively leached. This process of manganese solubilization and recovery followed by replenishment and recycling of the medium was repeated until 98 pct manganese was extracted from the ore.

Jan 1, 1993