Search Documents

By H S. Mitri, A Sainoki

Destress blasting techniques have been widely employed in underground mines for the purpose of preconditioning highly stressed rock mass. Appropriate applications of the technique successfully contribute to increasing mine safety (eg mitigating the risks for rock bursts). This paper presents a simulation technique to estimate the extent of damage zones induced by destress blasting. A 3D numerical model with a single blasthole is constructed with FLAC3D code, whereby static analysis is carried out in which horizontal and vertical stresses are applied to the model in order to simulate stress conditions in a deep underground mine. Afterwards, dynamic analysis is performed whilst applying time-varying blast pressure along the blasthole. The blast pressure profile takes into consideration an instantaneous increase and gradual decrease in blast pressure as well as the propagation of detonation along the blasthole. In this paper, constitutive models allowing for shear and tensile strengths of rock mass that are dependent upon strain rate are newly implemented into FLAC3D code with C++ programming language, whereby blast-induced damage is assessed by the extent of tensile and shear failure zones. The results obtained from the dynamic analysis show significant decrease in the extent of yielding zones induced by destress blasting with increasing the magnitude of in situ stress. They indicate that considering in situ stress state is indispensable in order to propose proper blast design for each level in underground mines. Based on these results, the relationship between the extent of the damage zone and depth at which destress blasting is performed is established. Furthermore, stress dissipation induced by destress blasting is examined with static analyses, in which the modulus of elasticity is decreased according to a rock fragmentation factor, a, only for the area where tensile and shear failures takes place during the dynamic analyses. A model parametrical study with respect to a is undertaken. The relationship between the rock fragmentation factor and the stress dissipation in the yielding zones is developed from the parametrical study. The developed relationship can be useful when destress blasting is designed for massive rock masses.CITATION:Sainoki, A and Mitri, H S, 2015. Simulation of damage zones induced by destress blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 245–256 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By S. M. Bulatovic

The western industrial world has to rely more and more on complex polymetallic sulphide ores as sources for base metals. These ores are composed of fine grained sulphide minerals such as chalcopyrite, galena, sphalerite, pyrite, pyrrhotite and marcasite. The liberation sizes of the individual minerals can range between 30 um and 5 um. Therefore, applying conventional techniques to recover these finely disseminated minerals usually results in unsatisfactory metallurgical performances with high losses of the valuable mineral to the slime , fraction of the tailing. New concepts for treating these polymetallic complex ores are discussed in this paper. Beneficiation techniques utilizing new reagents and a new approach to pulp preparation are described. Some of these techniques were applied to ores from existing concentrators as well as to new ores. The results of these studies are discussed in the following sections.

Jan 1, 1990

By O. S. North

As recently as the late 1920's there Were few indications that a 15-million-dollar-a-year industry would ever grow out of the mineralogic curiosity vermiculite. Today, it is an important industrial commodity, used primarily as an insulating material and lightweight aggregate, but with a wide range of other applications. The quantity of crude vermiculite produced and used in the United States increased 14-fold in the 17 years between 1935 and 1951. The vermiculite minerals are of secondary origin, formed by hydrothermal alteration of an ultrabasic igneous rock, generally pyroxenite, or by alteration of phlogopite or biotite mica or possibly other similar minerals. According to different authorities, vermiculite may originate either by direct hydrothermel means, by the weathering of biotite or phlogopite, or by a combination of these two agencies. Vermiculites frequently occur at or near the contacts of an acid intrusive rock, especially a pegmatite dike, with a basic or ultrabasic country rock.

Jan 1, 1953

By A. Anani

The goal of hot mix asphalt (HMA) design is optimal material blending to meet Superpave specifications. HMA cost minimization has being modeled as linear programing (LP) (Awuah-Offei et al 2011) and mixed integer LP problems (Brown et al, 2012) and solved with commercial software such as LINDO and CPLEX. Often these software, which are designed to solve general optimization problems, have licenses that cost thousands of dollars. The objective of this study is to develop a novel solution algorithm to the HMA optimization problem presented by Brown et al. (2012), which will negate the need for expensive commercial packages and is specific to this problem. This novel algorithm is based on the branch and bound algorithm for solving mixed integer problems. The algorithm is incorporated into a software package with an easy-to-use graphical user interface. The developed algorithm is validated using a real-life HMA problem. Using this solution algorithm will save companies thousands of dollars, otherwise used to purchase software licenses.

Feb 23, 2014

By Joseph D. D?Annunzio

The report on cut and cover construction as assembled by the Organization for Economic Co-operation and Development covered 17 different countries based on a total of just under 400 individual replies of which about 30% of the replies were from the United States. In general, the review of replies to the questionnaire led to the impression that cut and cover construction is a very inadequate method which needed many improvements. This unfavorable judgment, however, resulted in the manner in which questions were asked rather than in the method itself, It can be concluded that the cut and cover construction method has proved itself as an excellent method and that it has reached a high degree of technological perfection, but inadequacies stilt exist, and for purposes of complete evaluation, comparisons with mining tunnelling methods should be carried out. The principal problem in cut and cover construction is the interaction during construction between the construction process and the existing use of the surface and subsurface environment. The greatest impediments to cut and cover construction have little to do with the physical works being constructed, but more with creating a site in which the work can be performed. Utility relocation, traffice maintenance, and protection of existing structures are major problems for the construction contractor, and too frequently receive insufficient attention in preconstruction planning and design. Some OF the areas in which research should be undertaken are as follows:

Jan 1, 1970

By G Zhao, S Hapugoda, E R. Ramanaidou, P Hapugoda, Y Jin, G O’Brien

In 2021 the ports of Port Hedland and Dampier in the Pilbara Region of Western Australia handled 900 Mt of iron ore. This ore was produced in the Hamersley’s mines and transported by trains to the ports for subsequent export. Dust, which is generally considered to be particles less than 100 μm in diameter, is generated at all steps in the supply chain. Whilst all dust may have potential impacts on human health and mangroves and buildings a proportion of the dust is classed as respirable (PM10) dust, which consists of particles <10 μm in diameter. In 2021, in response to the community concern with iron ore dust, CSIRO commissioned an internal study to characterise and benchmark the dustiness of the different ores and to develop targeted strategies to minimise dust impacts, without affecting other iron properties, such as stickiness during transportation. A specific concern is that that the dust in the PM10 fraction may contain significant amounts of particulates, such as free silicates which may have health implications for the workers and residents. This study provided detailed mineral and chemical characterisation of the dust generated from the railed fine ore products for five generic Australian ore types: Australian Channel iron Deposit (ACID), Australian Brockman (AB), Australian Marra Mamba (AMM), Australian Pilbara (AP) and Australian magnetite (AM). The dust from these fine ore products were compared to that generated from a sample of Brazilian Hematite (BH) type ore fines. The ores were evaluated for their physical, chemical and mineralogy properties, dust generating potential and understandings of the relationship between the dustiness of iron ores and their physiochemical properties. The size distributions of the railed fine ore products were determined and a suite of analyses were conducted on subsamples of total (-106 μm) and fine (-38 μm) dust. For all the ores, the total dust fraction contains less Fe and more contaminants (SiO2 and Al2O3) than did the bulk ore. The fine dust fraction contained even less Fe and more contaminants (SiO2 and Al2O3) than the total dust fraction. This suggests that the iron ore dust contains more clay and potentially free silica than does the bulk ore. These findings were supported by optical and Scanning electron microscopy analyses of the samples. Dustiness measurements were made for each of the different ores (-106 μm) to investigate the relationship of dustiness of various iron ores with their physiochemical properties and assess their responses to dust suppression by the application of water sprays.

Sep 18, 2023

"Real time analysis of conveyed bulk materials can be used to improve process performance by reducing variability and upgrading ore quality through selective removal of increments of flow that do not meet appropriate selection criteria. This paper focusses on proven Prompt Gamma Neutron Activation Analysis (PGNAA) and microwave transmission technologies used to representatively measure conveyed ore quality in real time so that meaningful decisions can be made between the mine and mill. This enables the effective removal by bulk diversion of small increments of conveyed flow such as waste, highly deleterious material or sub-economic material from the mill feed. Improved ore quality in plant feed optimises process performance, reduces processing costs and minimises tailings generation. Analysis is unaffected by particle size, dust, layering or segregation, mineralogy and belt speed. Technologies are explained and performance examples given from installations in copper and iron ore. The technology has been used successfully in bulk sorting for over twenty years typically using measured increments of a few minutes. Improvements in technology and calibration performance have resulted in accurate measurements over increments of thirty seconds and below.INTRODUCTION Ore quality variability exists on a number of scales. Block model grades represent a few hundred to many thousands of tonnes. Grade control at the mine occurs on a scale typically down to the size of a haul truck, which may be a few hundred tonnes. Highly variable ore quality is detrimental to process efficiency and effectiveness. Processing waste or low grade ore when higher quality feed is available represents a lost opportunity to generate higher revenues earlier in the operational life. Measuring ore quality accurately over short time increments during conveying enables small increments to be measured and diverted according to their quality. The paper explains the technology and benefits. Neutron irradiation techniques were considered potentially suitable for conveyed bauxite measurement by Beurton et al, 1995. Tran & Evans (2001) concluded there was no equivalent technology to Prompt Gamma Neutron Activation Analysis (PGNAA) in terms of material penetration power. PGNAA was evaluated by Nelson & Riddle (2003) for possible use in the phosphate industry and recommended its use for further characterisation of the mine’s various ore types to improve stockpile allocation and grade control. Cottle (2007) discussed test work for an iron sinter application and Delwig et al (2011) described the successful installation in 2009 and performance of PGNAA for base-to-acid ratio control in sinter feed with the analyser output used to control lime addition. Geoscan (PGNAA) works very well on iron ore and can “improve control over what is happening in the plant” and that comfort can be provided in knowing that the product is on-spec according to Minnett (2010). PGNAA is not yet used in the minerals sector for tariff purposes as has occurred since 2000 with Coalscan (PGNAA) in coal (Minnett, 2010)."

Jan 1, 2017

By Daniel E. Walsh, P. D. Rao

"A four-inch compound water cyclone (CWC) was tested to evaluate its gold recovery characteristics when processing -4.8 mm run-or-pit, placer material. Neutron activated placer gold particles (840 to 37 microns) were used as radiotracers (/98Au) in a closed circuit ewe test loop to determine concentrator recovery; a procedure believed unique to this study. The effect on gold recovery of gold size and shape, feed pulp density, feed pressure, vortex finder clearance (VFC), ewe cone type, top-size of the feed solids, presence or absence of heavy minerals in the feed, and the quantity of-37 micron slimes in the feed was investigated in over 300 tests.CWC concentration ratio and the top-size of the underflow solids were both affected by cone type, VFC, and feed pressure. Gold recovery was significantly affected by gold size, gold shape, and concentration ratio. These effects are complex, because significant size-concentration ratio and size-shape interactions exist. Radiotracer techniques showed gold particles had a residence time within the ewe of approximately one second. This study suggests ewe gold recovery is a concentration. This work suggests ewe gold recovery is a function of particle size and shape, and the flow rate through the cyclone. CWC cone ""bed density"" is considered important only as a thin, protective layer, which shields coarser gold particles from the entraining currents and facilitates their movement through the CWC.IntroductionCompound water cyclones (CWC), or automedium cyclones, are enhanced gravity concentrators for the beneficiation for slurries of sand, coal, and ground ore (Fig. 1). They are called compound water cyclones because of the compound slopes of their basal cones (Fig. 2) and are operated to suppress classification phenomena in favour of gravity concentration effects. The compound water cyclone is not a new wet concentrator. It was developed in the late 1950s by Dr. Jan Visman through research sponsored by Canada&apos;s Department of Energy, Mines, and Resources. Since that time, it has become a common unit in coal washeries for cleaning fine coal. CWCs and other versions of concentrating cyclones have also shown promise for heavy minerals and precious metals recovery."

Jan 1, 1988

By C. Pace, D. Darlington, A. Montera, C. Lingren

"A phosphate beneficiation plant in Utah is using isotope-based Prompt Gamma Neutron Activation Analysis (PGNAA) technology to analyze the entire slurry streams of the incoming feed and final product in order to adjust the flotation circuits in near real time and optimize the plant output. The plant has gained greatly improved visibility/control and has reduced product variability for improved profitability and product quality. This paper takes a look at the economics as well as application details and the difference this technology provides in a phosphate application. SIMPLOT PHOSPHATES INTRODUCTION Simplot’s Vernal, Utah Phosphate Mine and Mill are located in the northeast corner of the state in the Uinta Mountains along US Highway 191, eleven miles north of the town of Vernal. The phosphoric acid and fertilizer plant fed by the Vernal mine is located 94 miles Northeast of Simplot Phosphates in Rock Springs, WY.At the Vernal plant, loader and shovel mining to 85 Ton capacity trucks is done at an annual rate of 3.8 Million tons of ore. Run of mine ore is crushed in a mineral sizer to minus 14 inch diameter at the rate 11,500 tons a day and transported to the SAG Mill’s 130,000 ton surge stockpile by overland belt. ORE RESERVES The ore is a Phosphoria Formation of sedimentary rock type dating to the Permian Age. The ore body rests over a 25 mile area on Weber Sandstone from the Pennsylvania and Permian geologic period. Layers of Phosphate Rock can vary in thickness from 0.3 up to 2.1 feet, alternating with layers of Mudstone. The eastern edge of the ore’s body Panel “G” runs 16 feet deep with a feed grade of 21.5% P205 with lower MgO diluents of less than 2.79%."

Jan 1, 2016

By D. K. Marjaniemi

The U.S. Bureau of Mines inventoried and characterized mineral sites and production plants within 200 km of the border in both the U.S. and Mexico. Sources of information included the USBM Minerals Availability System, the USBM Automated Mineral Information System, the USGS Mineral Resources Data System, the Mine Safety and Health Administration Address/Employment File, and the literature. Three hundred seventy-eight major construction material and industrial mineral properties were identified and characterized in the U.S. and Mexican parts of the Borderlands. Sixty-six major metallic mineral properties were identified and characterized in the Mexican part of the Borderlands.

Jan 1, 1996

By S. Lim, G. Walsh, V. Romero

The cable television show, Mythbusters, contacted the New Mexico Institute of Mining and Technology requesting a pressure gauge to be used in underwater testing. The requirements for the gauge were: it must be passive (i.e. require no power to function), it must indicate when a certain, pre-determined pressure was reached, and that indication was to be visual. A pressure gauge was developed, using standard, commercially available rupture discs, set to burst at 500 psi. Underwater testing was conducted using a 400 lb Pentolite charge. Test devices were set out at ranges from 50 to 200 feet from the seat of the blast. The rupture discs showed a lethal range up to 100 feet, but not at 150 feet. This result matched well with the behavior predicted through modeling and simple shock physics calculations. Additionally, the geometry between the incoming shock and the pressure gauge did not seem to have a strong effect on gauge performance.

Jan 1, 2009

By R. Buisman, K. Reyneke, M. Fullam, J. V. Brown

Most mineral processes currently in use, such as flotation, spirals, gravity concentrators, etc., are only effective over a small range of sizes, hence the upstream need for technology to accurately classify fines by size. The Pansep’s design is revolutionary. Slurry is fed onto connected mesh sections that move without bending or vibration, in a circular motion. Both sides of the screen mesh are utilized, so Panseps are self-cleaning and has half the footprint of other mesh-type screens. Developed in South Africa in 1997, the Pansep has proved itself very effective as a wet fines screen to effectively classify fine mineral fractions from 50 to 2,000 micron (325 to 10 mesh).

Jan 1, 2001

By Edwan Anderson Ariza Echeverri

O processo de estampagem a quente também conhecido como press hardening, é um dos métodos mais utilizados atualmente pela indústria automobilística para produzir aços de alta e ultra alta resistência. Esse processo é principalmente usado em peças relacionadas à segurança passiva e à resistência ao impacto, tais como pára-choques e barras de proteção laterais. O uso desse processo aumenta a segurança dos passageiros e reduz o peço do veículo e, portanto, o consumo de combustível. No presente estudo, amostras de aço ao boro foram deformadas a quente, não isotermicamente, a 850ºC e 750ºC em 30% a uma taxa de 0,5s-1. As microestruturas obtidas após deformação a 850ºC foram quase totalmente martensíticas, diferente das amostras deformadas a 750ºC, onde houve uma diminuição da fração volumétrica de martensita e um aumento da fração volumétrica de ferrita. Portanto, a deformação aplicada a 750ºC resultou em uma diminuição dos valores de microdureza. Desta forma, tornou-se possível investigar a influência da deformação em alta temperatura na transformação martensítica, na fração volumétrica de ferrita e nos resultados de microdureza.

Aug 16, 2017

By G. Sachs, G. Espey

Simple methods can be used for the determination of the residual stresses in thin walled tubing if the stresses consist of high tensile stresses at the one surface and high compressive stresses at the other surface. Such a stress distribution is approximated in sunk tubing and in deep-drawn shells. It is possible to cut sections from such articles in such a manner that a major part of the residual stress is relieved by a bending of the Part that is separated from the adjacent metal. The circumferential stress is evaluated from the change in diameter D, occurring on splitting a length of tubing (Fig. Ib) or from deflection resulting from the cutting out of a circumferential tongue (Fig. Ia) .6 The bending moment M released by such a flexure is. M - EI (I-I) = EI R1-R0 I - u2(R0-R1) I -V2 R0XR1 where E = modulus of elasticity, v = Poisson&apos;s ratio, I = moment of inertia of the section, R0 =. mean radius before splitting, R1 = mean radius after splitting. The release of this bending moment corresponds to the release of stresses, which, in a thin section, vary linearly from one surface to the other, and have the following value in a particular fiber a certain distance (x) from the surface: S = c d I - V2 x c x d 2 2 RI - R0____E (d ) R1 - R0 X R0 X R1 ~ i - u2 (2 x) Ro X R1 where C is the section modulus and d is the thickness of the section, the ratio M:C being d: 2 for a rectallgular section.* The maximum stress values at the surfaces are. Smax = +E X d X R1-R0 I — u2- 2 R0 X R1 For most purposes the simpler equations: EXd AD1 = ± I - u2 x dm2 and will be satisfactory, where D,, is the aver. age of the mean diameters of the tubing

Jan 1, 1942

By G. Sachs, G. Espey

Simple methods can be used for the determination of the residual stresses in thin walled tubing if the stresses consist of high tensile stresses at the one surface and high compressive stresses at the other surface. Such a stress distribution is approximated in sunk tubing and in deep-drawn shells. It is possible to cut sections from such articles in such a manner that a major part of the residual stress is relieved by a bending of the Part that is separated from the adjacent metal. The circumferential stress is evaluated from the change in diameter D, occurring on splitting a length of tubing (Fig. Ib) or from deflection resulting from the cutting out of a circumferential tongue (Fig. Ia) .6 The bending moment M released by such a flexure is. M - EI (I-I) = EI R1-R0 I - u2(R0-R1) I -V2 R0XR1 where E = modulus of elasticity, v = Poisson&apos;s ratio, I = moment of inertia of the section, R0 =. mean radius before splitting, R1 = mean radius after splitting. The release of this bending moment corresponds to the release of stresses, which, in a thin section, vary linearly from one surface to the other, and have the following value in a particular fiber a certain distance (x) from the surface: S = c d I - V2 x c x d 2 2 RI - R0____E (d ) R1 - R0 X R0 X R1 ~ i - u2 (2 x) Ro X R1 where C is the section modulus and d is the thickness of the section, the ratio M:C being d: 2 for a rectallgular section.* The maximum stress values at the surfaces are. Smax = +E X d X R1-R0 I — u2- 2 R0 X R1 For most purposes the simpler equations: EXd AD1 = ± I - u2 x dm2 and will be satisfactory, where D,, is the aver. age of the mean diameters of the tubing

Jan 1, 1942

By W. R. Penney, J. M. Richardson, J. Y. Oldshue

Introduction The mining industry has for years underrated the value of mixing in mineral processing unit operations. In present-day operations where leaching is playing an ever increasing role in the total profit picture, the need for good mixing is becoming more obvious. The engineer in the research laboratory and in the operations is by necessity becoming more familiar with the concepts of mixing. This section is designed to provide the engineer with mixing data and correlations sufficient to assist in the general planning of simple mixing systems.

Jan 1, 1985

By W. J. McConnell, C. P. Yaglaglou

"IntroductionThis paper on the kata thermometer is issued by the Bureau of Mines on account of the general interest in this instrument and the fact that it is frequently used in studies of mine ventilation conditions with regard to comfort and health of miners. It has been used in the studies being conducted along this line by the Bureau of Mines on the effects of high temperatures and humidities of air in mine working on the comfort conditions, as well as in studies of atmospheric conditions in mine, railway and vehicular tunnels.The study of the various physiological responses of the human body to different degrees of temperature combined with different percentages of relative humility in still and in moving air, now being conducted at the Pittsburgh experiment station of the bureau in the research laboratory of the American Society of Heating and Ventilating Engineers, cooperating with the Bureau of and the U. S. Public Health Service, presents an added opportunity of investigating the instruments that have been devised to measure atmospheric conditions as they affect the comfort and health of human beings.The ordinary mercury thermometer, as pointed out by Heberden3 almost hundred years ago is a very inadequate instrument for measuring the physiological effects of atmospheric conditions. It merely accounts for that part of the body heat lost by raliation and convection, while as a matter of fact greater part of the body heat resulting from the metabolic process within the body is eliminated by means of evaporation from the surface of the body."

Jan 1, 1924

By G. Lindkvist

Roasting of concentrates with high impurity levels is normally done in multiple- hearth furnaces where the concentrates are heated with oilfired burners in order to remove As, Sb and Bi before the final sulfide oxidation. Although it is a countercurrent heat exchange process it uses a lot of oil. In order to develop an energy saving, and from a working environmental point of view a less harmful process than the multiplehearth process, pilot-plant tests have been done in a two-stage fluidized bed for partial roasting. The test materials have been As-rich concentrates with 8-25 % As some 5b and Bi. The Cu-content was 0-28 %. The tests have been successful with <0.3 % As,in the calcine and with an elimination of 5b between 80 and 90 %. In order to achieve the proper conditions for good impurity removal, 1.e. right temperature,residence time and sulphur potential, the tests were performed in a special designed roaster. The roaster consists of two beds with the facilities for recirculation of calcine, preheating of the blast, and possibility to use oxygen enrichment. The construction makes it easy to control the reactions that generate the heat in the bed and reduce the amount of dust that passes through the cyclones. As two roasting steps are used, the possibility to obtain optimal conditions for impurity removal is improved and the calcine can either be smelted to a normal matte, or after being dead-roasted in the second stage, be leached in the normal way for gold extraction. The calcine was smelted with slag. The matte and the slag obtained had low quantities of impurities in the matte and a favourable distribution of impurities to the slag.

Jan 1, 1983

By R. H. King

This paper describes the results of an underground coal mine trial installation of a shielded trailing cable. The cable was a three conductor, round, type SHC-GC, and was installed on a shuttle car in a conventional room and pillar mining section. The purpose of presenting the information is to prepare mine operators for proposed legislation that will require shielding on low-voltage trailing cables. Specifically, machine modifications are required to cable reels, packing glands, and couplers. Cable splicing is not as complex as expected but additional materials are needed in the kit and splice training is necessary. Even though shielding will cause some problems for the mine operator, it can reduce the hazard of electrical shock to mine workers. This paper will present information that mine operators can use to solve most of the problems that will be encountered if they are required to install shielded cables. The in-mine evaluation was funded by the U.S. Bureau of Mines.

Jan 1, 1980

By Shangyong Lin, Wei Sun, Weiping Liu, Muhammad Azam, Junfeng Chen, Yujie Zhao, David Asubonteng, Michael Ngoie

Copper concentrates are widely used in smelting operations worldwide and typically consist of chalcopyrite ( CuFeS2) as the primary mineral, with chalcocite ( Cu2S) and bornite ( Cu5FeS4) as secondary copper-bearing minerals. However, these concentrates often contain hazardous impurities, such as the fluorine ion, which can result in various complications during the smelting process. These issues include equipment corrosion, gas treatment requirements, environmental hazards, and strained community relations. Furthermore, high fluorine content in copper concentrates can lead to penalties and limitations during sales. To address these challenges, this comprehensive review assesses current techniques for removing fluorine from copper concentrate. Drawing upon recent research and the findings in the field, the review analyzes the advantages and disadvantages of existing fluorine removal methods and identifies critical issues requiring attention in the future. This review provides valuable insights into the current state of fluorine removal from copper concentrates and serves as a practical guide for researchers and industry professionals in this field.

Aug 2, 2023