Search Documents

As the high-grade copper deposits in the world become depleted, there is an increasing focus on developing lower-grade ores which contain problematic impurities such as arsenic. Indeed, many high-arsenic ore bodies remain undeveloped because of their high arsenic levels. Separation of arsenic from copper at the beneficiation stage is difficult using the current processing techniques and invariably copper concentrates produced from these ores contain high arsenic levels, sometimes so high as to make them unacceptable to copper smelters. New, sustainable approaches are needed to allow development of high-arsenic copper ores while at the same time minimizing arsenic dispersion into the biosphere. The most promising route for separating arsenic from copper at the flotation stage centers on the use of pulp potential control. In recent years CSIRO has demonstrated at laboratory scale, for a number of high-arsenic copper ores, that crude flotation separation between arsenic-bearing minerals and copper-bearing minerals can be made. The differences in specific minerals responses to changes in pulp potential and pulp pH are exploited for this separation. Such separations nominally produce a low-arsenic high-copper concentrate and a low-copper high-arsenic concentrate. The former can be smelted without penalty, while the latter requires further treatment to capture and stabilize the arsenic and to recover the residual copper. Consideration has now been given to treatment options for the high-arsenic low-copper product. A pyrometallurgical option, involving a low temperature roast to selectively fume off the arsenic and leave a high-copper calcine, coupled with an arsenic stabilization step, has been demonstrated in the laboratory, and a preliminary techno-economic evaluation shows the process to be economically favorable. These results were recently published. CSIRO has now investigated an alternate hydrometallurgical option, involving atmospheric alkaline sulphide leaching of the high-arsenic product, where the arsenic is selectively dissolved leaving a copper-rich leach residue. The leaching testwork was carried at on the same high-arsenic low-copper material used in the roasting studies, enabling a techno-economic comparison of the alternate roasting and leaching treatment options to be made. The alkaline leaching work is briefly described and the results of the process option comparison presented and discussed. Keywords: arsenic, copper, economics, enargite, ore flotation, tennantite INTRODUCTION

Sep 1, 2012

By H. Soltanzadeh

This paper summarizes semi-analytical and closed-form solutions that can be used to assess the poroelastic stress changes induced within a porous formation (reservoir) during a pore pressure change. Further, solutions are presented for the stress discontinuities at the interfaces between reservoirs and the rocks that surround them. When used in combination with rock failure criteria, these solutions enable relatively simple analyses of the potential for induced fracturing or fault reactivation within a reservoir or the rock immediately adjacent to it. The latter, in particular, is useful for assessing if the hydraulic integrity of the surrounding rock (i.e., the bounding seal) will be affected by a pore pressure change. The use of the approach presented in this paper is illustrated with an analysis of a pinnacle reef with dimensions and properties representative of reefs in the Zama oil field, northwestern Alberta, Canada. Scenarios of pore pressure decrease (during historical production operations) and pore pressure increase (during several years of acid gas injection operations) are analyzed, for three different idealizations of reservoir properties and geometry (two plane strain and one axisymmetric). These results suggest that that the potential for induced fracturing is not significant at any point within the reservoir or the surrounding rock for both the production and injection scenarios that were simulated. Similarly, fault reactivation was not predicted for the reservoir or any of the points that were analyzed in the surrounding rock. However, fault orientations having the greatest potential for reactivating during historical production operations were identified; thus, illustrating a means of using geomechanical models to focus geological characterization efforts on the features that are most critical to acid gas containment.

May 1, 2009

By A. Aly Selirn

An economic simulation model was developed to predict the amount of copper recovered from copper oxide deposits and the cost of producing it as a function of the deposit parameters. The economic simulation model includes models of fragmentation design and cost, copper extraction, solution distribution and recovery, effluent solution cutoff grade, and financial analysis. Cost and price indices were also developed to evaluate the economic feasibility of in situ leaching operations as a function of their starting date. Application of the models to various properties having the same area and different ore thickness shows that the effluent solution cutoff grade does not vary with the ore thickness nor with its grade. The percent of copper recovery is, however, shown to increase with the increase in the ore thickness and is independent of the ore grade. it is also shown that while the profit per unit of extracted copper increases with the increase in ore grade or ore thickness, the rate of return on total investment does not show any correlation

Jan 1, 1977

By Thomas E. P. Wechsler

The limiting factor for most pyro-metallurgical processes in secondary cop- per melting is the time required to heat and melt the product. American Combustion's proprietary PYRETRON variable £uel/air/oxygen combustion system improves the throughput of existing scrap melting and heating furnaces for copper and copper alloy production by increasing the rate of heat transfer from the flame to the product. The increased productivity and energy savings obtained from this technology can result in sizable reductions in operating costs for smelting operations.

Jan 1, 1991

By John Mould, Gordon Chen, Michael Oakland, William McElwee

"This paper will discuss the design analysis of sheet pile cofferdams for static and dynamic blast loads. Following construction of the new Willis Avenue Bridge across the East River between Brooklyn and Manhattan, in-river piers No. 9 and No. 10 from the former bridge were demolished, partially by explosive charges. The blast at Pier 10 was conducted first and though the demolition charge was relatively small, it gave confidence that the sheeting could be designed to resist the blast load. This paper primarily summarizes our analysis and performance of a sheet pile cofferdam at Pier 9 used to withstand the larger blast loads, contain the blast debris, and allow excavation of the pier below the existing river bed mudline. The program NLFlex was used to predict stresses and deformations of the cofferdams under dynamic blast loads, using simplified equations to estimate the underwater blast pressures. Specifically, the analysis focused on the stresses in the struts, waler beam, sheet pile interlocks and connection of the sheeting to the waler beam. Design included allowing plastic deformations and limited rupture of the sheet pile interlocks under the blast loading. Comparisons are made between stresses assessed by the dynamic finite element modeling and empirical relationships used within the industry. The performance of the system after the actual blast is discussed as well as details of the performance of welded vs. bolted connections within the system. IntroductionThe Willis Avenue Bridge is one of the major access ways from the Bronx into Manhattan. The location is shown on Figure 1. The original bridge constructed in 1901 was a swing bridge over the East River. The bridge was in disrepair and outdated with regards to its ability to handle the flow of traffic resulting in numerousaccidents.In 2007, Kiewit Constructors Inc./Weeks Marine, Inc., A Joint Venture was selected to construct a replacement bridge. The $612 million project included construction of a new bridge just to the south of the original bridge. The most notable aspect of the construction was floating and lifting the new 350 ft. long swing span in place as a single piece. However, another significant challenge was using blasting to demolish two of the abandoned piers which were within the East River. The blast would be near existing structures in both Manhattan and Brooklyn and would be within 30 ft. of the new bridge."

Jan 1, 2017

By Greg J. Hasenfus, Allison M. Haines, Joshua M. Silvis

The floodable volume of longwall gob can be of great importance in developing accurate coal mine operation plans, particularly for mine water management and environmental control strategies. Given the inaccessibility and difficulty in direct measurement of gob characteristics following gob recompression, hydrologic, geomechanical, and spatial data and principles were used to solve for the porosity and height of the residual gob using a mathematical model framework and bulking-based techniques. Based on this approach, gob porosity of Appalachian longwalls appears to be tighter than previously reported, ranging between 4.99 and 14.31%. Residual gob height, as normalized with respect to mine extraction height, ranges between 1.90 and 2.45. A novel, bedding-based bulking approach is ampliative with respect to existing roof caving and bulking fundamentals, as it has greater explanatory value compared with the traditional, lithologic-based bulking application. The efficacy of using the residual gob characteristics determined by the mathematical model and bedding-based bulking is examined using a causal comparative method, whereby time series prediction of historical groundwater rebound is compared with observed mine pool elevation data. Prediction accuracy is significantly improved using a prototype model to calculate void volume of longwall gob, specifically, the dependence of porosity of the gob material upon the longwall width to overburden depth ratio for movement basins of subcritical and critical panel widths. The potential implication of these findings toward hydrologic, geomechanical, and ventilation studies of longwall gob could be significant.

Aug 13, 2021

By John G. Henning

Unplanned ore dilution has a direct and large influence on the cost of a stope, and ultimately on the profitability of a mining operation. This paper presents results of a study on the influence of a variety of factors on ore dilution in a blasthole stoping environment. A series of 3-D numerical models were developed and analyzed to examine the effect of mining depth, stope geometry and stope setting within the orezone extraction sequence. To quantify modelled ore dilution from the three-dimensional simulations, the ore Dilution Density (DD) is a term introduced in this study to denote potential hanging-wall overbreak. It was found that hanging-wall overbreak is not significantly influenced by depth alone, and that stopes with large or small axial ratios are more stable than large rectangular stopes. It was also demonstrated that, in addition to stope dimension, the amount of unplanned dilution differed according to stope type. Five stope types were identified, based on their position within a tabular blasthole mining sequence. The methodology presented in this paper can be adopted to develop mine-specific design tools for the estimation of ore dilution associated with a proposed mine design. This can prove extremely helpful in the process of underground mine planning and optimization.

May 1, 2007

By J. Mácsik, J. Lindblom, C. Maurice, Susanne Nigéus

Using non-hazardous industrial residues in mine waste remediation is beneficial not only for the mining industry where substantial amounts of the waste generated have potential to produce acid rock drainage and pollute the environment, but also the providing industry, minimizing the waste landfilled. In this study green liquor dregs (GLD), residue from 15 different paper mills were characterized to valorize it as a potential product as a cover material. In another part of the study, one of the GLDs and a local till were characterized to determine the optimal mixture of GLD amended till to be used in a field application at the closed Näsliden Mine in northern Sweden. The study concluded 10% GLD-amended till to be the optimal recipe and was successfully applied at the Näsliden mine waste dump. However, the great variability in the characteristics of GLD creates challenges if it is to be valorized as a product.

Dec 7, 2023

By Joseph D. Weeks

NOTE BY THE SECRETARY.—This address having been made the object of much hostile comment, arising, as Mr. Weeks believed, in large part from misunderstanding of its purpose and meaning, was, by his express direction, withheld from official publication in the Transactions until he should have so modified or added to it as to make such misunderstanding impossible. His illness and death prevented him from executing this intention; and, consequently, the only version of the address now in the Secretary's hands is one of which the author had forbidden the publication. Under the circumstances, therefore, it seems best to publish, in this place, only some portions of the address and its appendixes which have a historical value and are beyond controversy, giving at the same time a summary of its general nature, based upon the original manuscript and upon correspondence with Mr. Weeks. For this summary, the Secretary is alone responsible. The address was essentially a restatement of well-known and established facts, which it interpreted as proving that, of the three elements of the Bessemer process (namely, the pneumatic principle, the successful mechanical application of that principle, and the recarburization with spiegeleisen), William Kelly was the first inventor of the first, Bessemer of the second, and Mushet of the third. Mr. Weeks used the words " original inventor " in the sense (as he explained in one place) of first inventor, and neither asserted nor believed that Bessemer's con-

Jan 1, 1897

By Robert Benedetti

This paper describes various mitigation methods in order to reduce the maximum acceleration of the floorboard of hulled vehicles when explosive charges buried in water saturated sand were detonated beneath them. The effects on floorboard acceleration of adding a vehicle hull, several types of floorboard bracing, the use of foam to fill the gap between the floorboard and hull, and the use of foam to isolate the floorboard from the hull have been investigated. Small scale testing was conducted, which used bar magnet velocity gages to measure the velocity as a function of time of the center of the floorboard, directly over the charge, where the acceleration was expected to be greatest.

Jan 1, 2012

By Calvin J. Konya

An investigation was performed to determine conditions which optimize fracture formation between blastholes used for purposes of pre-splitting. Experiments-involved high-speed photography in Plexiglas models and radiographs in sandstone models. Additionail data was obtained from full-scale pre-split blasts. Pre-split fractures between blastholes were found to form as a result of gas pressure and were affected little, if any, by stress wave interactions. Pre-splitting was effective with short period delays of 25 milliseconds or less, and did not require instantaneous initiation of blastholes. Significant reduction of ground vibration resulted with the use of delays

Jan 1, 1980

By M. Misra

The dielectric properties and flotability of different ranks of Argonne Premium Coal samples are presented. The flotability of different ranks of coal are correlated with the dielectric properties and intrinsic moisture (or bound water) content. Measured dielectric properties of as-received coals and other constituents are incorporated into a mixture equation to calculate the dielectric properties of bound water present in the different ranks of coal. The nature of bound water present in low-rank hydrophilic coals is significantly different from that present in high-rank hydrophobic coals. The water molecules present in low-rank lignite have an oriented dipole-dipole interaction and are tightly bound to the surface. For high-rank coals, the water molecules are not bound to the surface and have a randomly distributed clathrate ice-like structure. Controlled thermal treatment can modify the structural nature of bound water present in low-rank hydrophilic coals and increase their flotability.

Jan 1, 1990

By T S. Cochrane

This paper is based on observations made during a recent visit by the writer to three of the dust research laboratories .in West Germany, each .of which is mainly concerned with studymg the composition and character of the respirable dust produced in mines or at industrial sites. The three institutes are discussed as regards their orgamzat10n and duties, their methods of dust sampling and analysis, and recent trends in research and development. An extensive bibliography completes the paper. Introduction A RECENT trip to Europe to attend international conferences m Austria and m Belgium gave the writer the opportunity to visit a number of research laboratories and mines in Western Europe. The visits to the dust research laboratories in West Germany are the basis of this report. In Germany, cooperative associations formed prior to and since the turn of the 20th Century to promote the safety and welfare of their workers have recognized the effects of airborne dust on the general health of the labour force.

Jan 1, 1964

By Takahiro Miki

In order to use metallurgical grade silicon (MG-Si) as a starting material for solar cell, phosphorus has to be removed from silicon because phosphorus is a n-type dopant. On the other hand, silicon, ferrosilicon, and silicomanganese are widely used as deoxidizers in steel refining processes. Since most of the phosphorus introduced during the deoxidation process is brought into final products, it is important -to lower the phosphorus content of these alloys. Hence, thermodynamics of phosphorus in such metals is important for the evaluation of dephosphorization processes. In the present study, thermodynamic properties of phosphorus in molten Si-P alloys at 1723- 1848K and those of Si-Fe-P and Si-Mn-P alloys at 1723K have been determined by equilibrating respective metals in a controlled phosphorus partial pressure. The results are expressed as follows.

Jan 1, 1998

By James M. Barker

Sulfur is a nonmetallic element of great physical and economic importance to the world. It is widely but sparingly distributed throughout the hydrosphere, lithosphere, and biosphere. Sulfur is the tenth most abundant element in the universe and eighth most abundant in the sun. In the earth's crust, which is mainly igneous, it ranks 14th, but is eighth or ninth in sediments (Kaplan, 1972; Stanton, 1972). It apparently is very abundant in the core of the earth, because it is a strong chalcophile, and it is fifth in abundance in stony and iron meteorites (Field, 1972) where it occurs as trolite (FeS). In ancient times sulfur was called brimstone, literally "burning stone." Today the term brimstone is used interchangeably with the term elemental sulfur. Shelton (1979) summarized most of the common definitions of terms, grades, and specifications for the sulfur industry as follows (with minor additions): Sources of Sulfur: Combined sulfur-Sulfur that occurs in nature combined with other elements. Cupriferous pyrites-Pyrite containing relatively minor amounts of copper sulfide minerals. Hydrogen sulfide-A toxic gas (H2S) occurring in natural gas and petroleum. Involuntary sulfur-Sulfur produced primarily as a result of legislative or process mandates. Native sulfur-Sulfur that occurs in nature in the elemental (uncombined) form. Nonferrous metal sulfides-Copper, lead, zinc, nickel, and molybdenum sulfides that are processed for their metal content. Organic sulfurs-Complex organic sulfur compounds occurring in petroleum, coal, oil shale, and tar sands. Pyrites-Iron sulfide minerals that include pyrite, marcasite, and pyrrhotite. Sulfate sulfurs-Sulfur in anhydrite and gypsum. Voluntary sulfur-Sulfur produced in response to market forces. Basic Sulfur Products Produced and Marketed: Acid sludge-Contaminated sulfuric acid usually returned to acid plants for reconstitution. Brimstone-Synonymous with crude sulfur. Bright sulfur-Crude sulfur free of discoloring impurities and bright yellow in color. Broken sulfur-Solid crude sulfur crushed to -8 in. Byproduct sulfuric acid--Sulfuric acid produced as a byproduct of a metallurgical or industrial process, generally relating to combined sulfur sources. Crude sulfur-Commercial nomenclature for elemental sulfur. Dark sulfur-Crude sulfur discolored by minor quantities of hydrocarbons ranging up to 0.3 % carbon content. Elemental sulfur-Processed sulfur in the elemental form produced from native sulfur or combined sulfur sources, generally with a minimum sulfur content of 99.5%. Formed sulfur-Elemental sulfur cast or pressed into particular shapes to enhance handling and to suppress dust generation and moisture retention. Frasch sulfur-Elemental sulfur produced from native sulfur sources by the Frasch mining process. Hydrogen sulfide-Associated with natural gas or petroleum and produced at refineries and coke oven plants; used to make sulfuric acid or recovered sulfur. Liquid sulfur-Synonymous with molten sulfur. Liquid sulfur dioxide-Purified sulfur dioxide compressed to the liquid phase. Molten sulfur-Crude sulfur in the molten phase.

Jan 1, 1983

By D. Y. Liang

Rare metal ores have those features of high industrial value and bad performance in ore separation. Most of rare metals ores are with low grade of valuable components, rareness of useful minerals, complicated combination of associated minerals and high difficulty in separation and enrichment of minerals. For those single (Ta, Nb) or (Ta, Nb, Sn) ore occurred in granite and pegmatite, the ways of gravity separation and magneto electric separation to concentrate (Ta, Nb) minerals are adopted. There are many mines being explored successfully both at home and aboard. While, for complex (Nb-Zr-REE) ores associated with Be and Ti minerals, they are commonly considered as rich rare metals ore but more difficult to process. One of rare metals mine in Inner Mongolia has the features as with large reserves and high grade of columbium and zirconium and accompanies with REE and beryllium, therefore with significant industrial value. After the utilization of research method of process mineralogy, detailed mineralogy research has been made on the rare metals ore. The test results show that there are abroad isomorphism replacements among such elements, such as Ti, Mn, Fe, Nb and Ta, between Be and REE in metallic oxide minerals of that ore, which makes the mineral composition of that ore extremely complicated. This research identifies clearly the mineral composition, and investigate at the technological property and the occurrence of those elements as Nb, Zr, Be and REE in the rare metal ore. The achievements of this research provide important mineralogy basis for ore dressing research of refractory rare metallic ores.

Jan 1, 2014

By J. A. Hansuld

"THIS SESSION marks something of a milestone in that it is, as far as I know, the first session at a CIM Annual Meeting devoted entirely to exploration geochemistry. This is an indication of the general acceptance and widespread recognition by industry of geochemistry in mineral exploration. As a first, I hope it proves sufficiently successful and interesting that geochemical exploration sessions will become a routine part of future CIM annual meetings. The greater use and acceptance of geochemistry has resulted in many investigations and advances, especially in areas such as the Canadian Shield. For a first session on geochemistry, the meeting in Quebec suggested an ideal opportunity to assess these advances and report on the current application of geochemistry in the Shield. The theme of the session is ""Geochemical Exploration in the Canadian Shield - The State of the Art."" A series of six papers will be presented dealing with the various dispersion media - rocks, heavy minerals, ""soils"", lake sediments, waters and vegetation. As a background to the individual presentations, I would like to take a few minutes to briefly trace the history of the use of geochemistry in the Canadian Shield."

Jan 1, 1971

By V Mutton, L Potts, D Joyce

This paper describes the method of extracting sill pillars within the underground operation from under unconsolidated mullock fill at the Cracow Gold Mine. This pillar recovery method was initially successfully used to recover sill pillars at Crusader Mine, Western Australia in 2001. Globally significant resources have been sterilised due to the placement of loose rock fill above crown pillars and within adjacent stopes. The method described here offers significant opportunities to increase recovery of sill pillar recoveries.The royal orebody sill pillars at Cracow Gold Mine form a significant resource. Extraction of these pillars needed to be undertaken with minimal ore dilution and maximum ore recovery. The application that was selected to consolidate the loose mullock fill above each pillar used an injection grouting process (Minova FB200).Cracow Gold Mine mining method is bottom up bench mining. The pillars were left within the orebody to allow for stoping to commence whilst the decline was being developed. Due to the remainder of the orebody being extracted the only access to consolidate the backfill was from the sill pillar extraction level. Numerous problems were encountered and overcome from product selection and trial, system of injection to extraction.This pillar recovery process achieved a 95 per cent recovery of the sill pillar compared with an estimated 60 per cent typical for other mining options.CITATION:Potts, L, Mutton, V and Joyce, D, 2012. Pillar recovery at Cracow gold mine using grouted consolidated mullock, in Proceedings Narrow Vein Mining 2012 , pp 179-184 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By H. H. Uhlig

SINCE its first mention in the literature in the eighteenth century1,2 the phenomenon of passivity in metals has stimulated much speculation and attendant controversy as to its nature and cause. No one of the numerous theories so far proposed has been generally accepted. ? Faraday,7 in 1836, associated the passivity of iron with a protective film over the surface of the metal, which materially prevents or slows down reaction with corrosive environments. His theory was that oxidizing acids like nitric acid form an unstable oxygen or oxide layer over the iron surface, which protects the underlying metal from further attack. This concept was simple yet plausible, and without alteration has frequently been assigned in present-day discussions as explanation of the passivity of many metals. With the advent in recent times of stainless steels, it is not surprising that this oxide film theory of passivity proposed by Faraday has been used to explain the phenomenal corrosion resistance of stainless steels and other passive alloys. The passive alloys, such as the chrome-iron alloys, are supposedly covered with a protective oxide film, which forms on exposure of the alloy to air, is extremely stable and self-healing, and accounts for the remarkable resistance of these alloys to corrosion. Within the past few years, several investigators, following the theory of film protection, have attempted to gauge the resistance of the supposed film on steels. Brennert8 and Donker and Dengg9 determined the poten-tial at which a negative ion (e.g., Cl-) moving in an electric field reacted with the metal anode, as detected by increased current flow or change in potential of the steel electrode in an electrolytic cell. The potential corresponding to reaction Brennert called the film break-through potential.

Jan 1, 1939

By Michael Oakland

This paper will discuss the design analysis of sheet pile cofferdams for static and dynamic blast loads. Following construction of the new Willis Avenue Bridge across the East River between Brooklyn and Manhattan, in-river piers No. 9 and No. 10 from the former bridge were demolished, partially by explosive charges. The blast at Pier 10 was conducted first and though the demolition charge was relatively small, it gave confidence that the sheeting could be designed to resist the blast load. This paper primarily summarizes our analysis and performance of a sheet pile cofferdam at Pier 9 used to withstand the larger blast loads, contain the blast debris, and allow excavation of the pier below the existing river bed mudline. The program NLFlex was used to predict stresses and deformations of the cofferdams under dynamic blast loads, using simplified equations to estimate the underwater blast pressures. Specifically, the analysis focused on the stresses in the struts, waler beam, sheet pile interlocks and connection of the sheeting to the waler beam. Design included allowing plastic deformations and limited rupture of the sheet pile interlocks under the blast loading. Comparisons are made between stresses assessed by the dynamic finite element modeling and empirical relationships used within the industry. The performance of the system after the actual blast is discussed as well as details of the performance of welded vs. bolted connections within the system.