Search Documents

By R. O. Dannenberg

The Bureau of Mines conducted laboratory investigations with the objective of developing an alternative process for recovering cobalt and copper from complex sulfide concentrates. Processes currently used depend largely upon precipitation techniques to remove impurities and recover cobalt from sulfate liquors prepared by oxidative pressure leaching of the sulfide concentrates. The Bureau conducted bench-scale research on a process for treating cobaltite concentrates, comprising (1) oxidative pressure leaching, (2) jarosite precipitation followed by H202 oxidation and pH control to remove iron and arsenic, (3) copper solvent extraction with a mixed hydroxyoxime-amine extractant, (4) copper electrowinning from recirculating acidic strip liquor, (5) selective cobalt extraction from copper solvent extraction raffinate with a phosphinic acid extractant, and (6) electrowinning of cobalt from a recirculating weak acid strip liquor. Overall cobalt and copper recoveries were 91.7 and 84.1 pct, respectively. Electrowon products assayed 99.8 pct Co and 99.89 pct Cu.

Jan 1, 1987

By S. E. Vanderslice, J. A. Hummer

"The results of laboratory evaluations were used to compare the potential of two alternative, biomass-derived fuels as a control strategy to reduce the exposure of underground miners to aerosols and gases emitted by diesel-powered equipment. The effects of fatty acid methyl ester (FAME) biodiesel and hydrotreated vegetable oil renewable diesel (HVORD) on criteria aerosol and gaseous emissions from an older-technology, naturally aspirated, mechanically controlled engine equipped with a diesel oxidation catalytic converter were compared with those of widely used petroleum-derived, ultralow-sulfur diesels (ULSDs). The emissions were characterized for four selected steady-state conditions. When fueled with FAME biodiesel and HVORD, the engine emitted less aerosols by total particulate mass, total carbon mass, elemental carbon mass and total number than when it was fueled with ULSDs. Compared with ULSDs, FAME biodiesel and HVORD produced aerosols that were characterized by single modal distributions, smaller count median diameters, and lower total and peak concentrations. For the majority of test cases, FAME biodiesel and HVORD favorably affected nitric oxide (NO) and adversely affected nitrogen dioxide (NO2) generation. Therefore, the use of these alternative fuels appears to be a viable tool for the underground mining industry to address the issues related to emissions from diesel engines, and to transition toward more universal solutions provided by advanced engines with integrated exhaust aftertreatment technologies. IntroductionDiesel engines have been the workhorses of modern society for industrial and transportation enterprises. Diesel engines of all generations are extensively used in a variety of light-, medium- and heavy-duty applications in underground mining operations around the world. Fuels obtained from various sources and with wide-ranging chemistries have been combusted in diesel engines. However, the bulk of the currently used fuel can still be traced to nonrenewable petroleum sources. The petroleum-derived diesel fuels are primarily made up of saturated acyclic hydrocarbons (parafins or alkanes), aromatic hydrocarbons (arenes or aryl hydrocarbon), and unsaturated hydrocarbons with double bonds (olefins and alkenes). Improvements in the quality of petroleum-based diesel fuels was identified in federal regulations as an important piece in resolving the puzzle of diesel engine emissions (Environmental Protection Agency, 2001, 2004). The reduction of U.S. diesel fuel sulfur content below 15 ppm had the effect of lowering sulfate emissions and enabling the development and implementation of catalyzed emissions control technology across a wide spectrum of applications."

Jan 12, 2017

By Ruichen Ren, Xu Han, Caixia Li, Zengchuan Yue

In this paper, the size-density distribution of coarse middling coking coal (CMCC) with different grinding fineness and flotation concentrates was investigated. Then, the flotation behaviors and liberation characteristics of different size-density fractions in ground CMCC were analyzed, and the different size-density fractions were divided into five categories: mostbeneficial, secondary-beneficial, poorly liberated, insignificant-pollution, and serious-pollution. Based on the content of particles with different liberation characteristics, an evaluation index of the liberation characteristic of ground CMCC, namely, the liberation perfection index (LPI), was proposed. The results indicated that grinding changed the size-density composition of CMCC, which affected the flotation performance. Insufficient grinding and overgrinding were not beneficial to flotation. Insufficient grinding caused a higher content of poorly liberated particles and a lower content of most-beneficial particles. Overgrinding increased the content of serious-pollution particles and reduced the content of most-beneficial particles. The size order of the LPI values of different ground CMCC was consistent with the flotation efficiency, and the LPI values of the other two similar samples were overall positively correlated with their flotation performance, suggesting that the method is universal.

Feb 14, 2023

The results of laboratory, large-scale laboratory and commercial scale investigations regarding the process of slag melts cleaning by oxidizing-reduction gas mixtures with a wide range of Po2 and the use of matte of various compositions as an extracting phase are presented. The copper, nickel and cobalt behavior during the cleaning process has been studied based on SEM and x-ray Microprobe of the quenched slag melts. The general cleaning mechanisms have been found. On the basis of the obtained data the most efficient cleaning methods have been proposed.

Jan 1, 2003

By Diler Katircioglu-Bayel

The effects of the operating parameters of media filling ratio, solid mass fraction, grinding media size and grinding time on the stirred media milling of talc were studied. The findings were assessed based on the product particle size (d50, d10), surface area (Sw) and energy consumption (Em). Furthermore, after determining the optimum grinding conditions, Box-Behnken statistical design was used to determine the effect of parameter interactions on the d50 size. The media filling ratio significantly affects d50 size decrease compared with solid mass fraction and grinding time. The minimum d50 size was also achieved under optimum grinding conditions.

By E. M. SEELEY, F. S. LOTT

The total capacity of the natural-gasoline industry to produce light hydrocarbon products increased to 21,322,000 gallons ( 507,670 barrels ) daily on January 1 , 1948 , from 17,928,000 gallons ( 426,860 barrels ) daily on January 1 , 1946. Expansion of the industry in the first two post -war years , 1946 end 1947 , thus averaged 9 percent annually , compared with 6 percent annually in the last two war years , 1944 and 1945 . The number of cycle plants increased only from 37 to 39 in the years 1946 and 1947 , and total capacity of these plants gained 21 percent to 5,857,000 gallons de ily on January 1 , 1948 , represent ing 27.5 percent of the total capacity of the industry , compared with 27.0 percent on January 1 , 1946. All other plants decreased in number in the two-year period from 589 to 510 on January 1 , 1948 , but their total daily capacity increased 18 percent to 15,465,000 gallons . The daily capacity of the average plant in the industry was enlarged from 28,600 gallons on January 1 , 1946 , to 38,800 gallons on January 1 , 1948 , continuing the long -established trend to producing units of greater size and efficiency . The average cycle plant capacity increased from 131,000 gallons daily to 150,200 gallons daily on the same dates as the average capacity of all other natural -gasoline plants increased from 22,200 gallons to 30,300 gallons . Owing to the elimination of small , obsolescent plants in Illinois , Oklahoma , and Pennsylvania , these States experienced the greatest reductions in numbers of plants in 1946 and 1947. In Oklahoma and Texas , several consolidations of two or more plants into a single operating unit were reported . Louisiana and Mississippi were the only States in which the number of plants increased , but daily capacity to produce light products was larger in eleven States on January 1 , 1948, than two years earlier . Added facilities in California and Texas accounted for 41 and 36 percent , respectively, of the national gain in capacity .

Sep 1, 1948

By X. W. Pan

It has been found that the MnO content of a slag decreases sharply when direct current is applied to a 1T1£tal-Slagsystem consisting of liquid Mn-Si-Ccsat metals and MnO-SiO2-CaO-AI203 slag in graphite crucibles. This paper reports a preliminary investigation into the electrochemical effects of direct current on the metal-slag system, the silicon content of the metals, and the MnO content of the slag. The results show that, when a direct current of 7 A is maintained, the MnO content of a metal containing 10 to 11 per cent silicon by weight is reduced rapidly from 26,5 to 17,2 per cent by weight. This reduction seems to proceed further when the process is continued. When the direct current and the voltage are kept constant at TA and 4 V respectively, the MnO content of a metal containing 1 to 2 per cent silicon by weight is reduced to 1 from 25 per cent by weight, which results in a manganese yield of 96 per cent.

Jan 1, 1995

By Felipe Lacerda Giro

Atualmente, a soldagem por extrusão de peças semi-acabadas (chapas) em PEAD tem se mostrado como uma solução atraente para a fabricação de pequenas embarcações de serviço. Neste sentido, a qualidade da soldagem torna-se um elemento fundamental para a garantia da integridade estrutural da embarcação. Neste trabalho são apresentados os resultados da análise da influência de diferentes fatores na qualidade da soldagem por extrusão de chapas de polietileno de alta densidade. Os fatores analisados envolveram o aporte de calor, a preparação do chanfro, a velocidade de soldagem e a pigmentação do fio de solda. A influência de tais fatores na qualidade da solda foi avaliada tendo como referência os resultados de ensaios de flexão em corpos de prova.

Aug 17, 2017

By C. J. Newman, R. J. St. Eloi, G. Macfarlane

"The Kidd Creek copper smelter has been expanded from its original design of59000 tonnes of copper per year to over 120 000 tonnes per year. Modifications to the process gas handling system and acid plant have been made to accommodate this higher production rate and, generally, to optimize the operation.The gas handling system associated with the continuous smelting process is discussed in terms of boiler accretions and modifications to minimize their impact on operations; design changes to effect reductions in high pressure drop duct configurations; material changes to overcome corrosion and plant additions to improve gas cleaning capability. The acid plant is reviewed with references to changes made to accommodate the increased S02 gas strength resulting from the higher smelting rates. IntroductionThe Kidd Creek Division of Falconbridge Limited is a base-metal mining and metallurgical complex located in Timmins, Ontario. The discovery of the original copper-zinc-silver orebody was announced in April 1964. Mining operations began in 1966 with a 9000 tonnes per day (t/d) concentrator corning on stream in November of that year. In April 1972, a 108 000 tonnes per year zinc plant was conunissioned. Over the years the facilities have been expanded, such that the concentrator now has the capacity to process 13 000 t/d of ore. To expand zinc production, the world's second installation of the Commco/Sherritt pressure leaching facility was completed in 1983 to bring total zinc production capacity to 136 000 tonnes per year. In 1973, serious planning for a smelter operation began. In early 1975, after studying both continuous smelting and flash smelting processes, a decision was made to proceed with the technology offered by Mitsubishi Metal Corporation of Japan. The Mitsubishi Continuous Smelting Process was to be used for the smelter and the Onahama No. 3 tankhouse technology for the copper refinery."

Jan 1, 1994

By J. E. Gillespie

Introduction Mineral wool may be defined as "rock, slag, or glass fibres made by a process of melting and blowing by steam or air, containing a minimum of oil and unfiberized material" (U.S. Bureau of Standards CS 117-44). The earliest production of the material was in Wales, about one hundred years ago. In the United States, the industry daces from 1870 when a plant, using slag as raw material, was established in Greenfield, New Jersey. It was not until 1897, however, that large-scale production was commenced on this continent at a plant in Alexandria, Indiana, which utilized rock from nearby deposits. Today, mineral wool is manufactured in many parts of the United States and Canada, the plants for the most part being in close proximity to deposits of suitable rock or to sources of slag. In the United States there are some seventy-five producers with a total annual capacity of nearly one million tons of wool. In Canada, in 1946, eleven manufacturers produced about fifty million square feet of batt-type mineral wool insulation material. Mineral wool is, perhaps, the most efficient of all heat-insulating materials and, moreover, it is fireproof, extremely durable, and insect- proof. Its high efficiency is due to the very low thermal conductivity of the fibres themselves and to the fact that the produce as marketed contains up to 90 per cent non-conducting air space. Depending on the degree of compression of the fibres in the manufactured product, the specific gravity ranges from 2 lb. to 10 lb. per cubic foot. Products Marketed Following are the principal forms in which mineral wool is marketed: Blanket. - Mineral wool with or without reinforcing on one or both sides, with various types of confining media, all suitably bound together.

Jan 1, 1948

By Juan Pablo Segovia, Alonso Pereira, Fernando Concha, Daniel Sbarbaro, Samuel Vergara

A robust theory of sedimentation-consolidation evolved and was accepted by researchers worldwide in the last two decades of the 20th century. This theory provides a reliable method of thickener design, simulation and control. However, a process model, simple or sophisticated, empirical or phenomenological, is useful only if it is possible to determine, in an objective way, its experimental parameters. Although it is important for a mineral processing plant to perform periodical laboratory test to determine thickening parameters, and in this way adjust the operation, not always these tests represent the behavior of the material in the process. It is important to be able to determine these parameters directly in the thickeners. Research workers at the University of Concepción developed new instrumentation, algorithms and software for the determination of thickening parameters. In this paper, two new instruments for the on-line determination of the settling velocity and the compressibility of the sediment are presented and results of tests in a major mineral processing plant in Chile are described.

Jan 1, 2014

Korea has about 68 hundreds million tons of limestone's reserves. Still, high-Ca2+ limestone containing more than 52% calcium oxide makes up for about 12% only; hence the need for securing and effectively developing limestone. The best solution is to manufacture precipitated calcium carbonate (PCC). The synthesis of PCC using high-Ca2+ limestone has several advantages including the efficient development of resources and easing the import dependence on PCC. The first step is the selection of suitable limestone for the synthesis of PCC. In this study, formation age was decided as the primary key point, with its effect on calcination, hydration, and synthesis of aragonite investigated. Results showed that the yield of aragonite increased when newer limestone was used. On the other hand, neither the activity and bulk density of quicklime nor the particle size of aragonite was affected by the formation age, although special values were registered following each formation age. Moreover, the bulk density of quicklime and particle size of aragonite tended to increase with decreasing activity. This result is different from that of the other experiment. Therefore, a suitable method for measuring the activity of quicklime for use in the manufacture of PCC must be established.

Jan 1, 2006

By G. R. Smith

This report describes research carried out by the Bureau of Mines to develop new technology for electrorefining metals at much higher current densities than those normally used in commercial practice, preliminary studies using rotating-ring and cylinder electrodes to increase the mass transport of copper are discussed. Following this work, single- and multichannel cells were developed that utilized a high electrolyte flow in the channels formed by the anode-cathode pairs. Using these cells, copper was successfully refined at current densities in the range of 70 to 300 amp/ft2. The effects of flow rate, electrolyte composition, and grain-refining and leveling agents on the morphology and purity of electrodeposited copper were determined.

Jan 1, 1979

By Milan Terčelj, Matej Drobne, Urška Klančnik, Peter Fajfar

The study of oxidation behavior of High Chromium Steel material used for surface layer of work rolls was carried out. Specimens taken directly from the roll were subjected to thermal fatigue in the temperature range between room temperature and 500 °C up to 700 °C by using thermo-mechanical simulator Gleeble 1500D. Our observation was focused on the impact of oxidation as a principal mechanism of degradation of the roll’s surface layer - mainly on the characteristics of oxidation propagation in relation to the test temperature and microstructure constituents characteristics of the material. Oxidation is considerably accelerated by certain characteristics of eutectic and primary carbides, i.e. their size (area), composition, morphology, orientation regarding to the water-cooled surface, etc. In the presented paper selected cases where emphasized oxidation takes place are investigated, analyzed and explained. Obtained results thus represent a contribution to explanation of conditions which lead to acceleration of oxidation behavior that in turn can lead to chipping or even early spalling of material from the roll surface layer.

Oct 1, 2019

By E. Busse

"Heath Steele Mines Ltd. operates a lead-zinc-copper mining and milling complex in New Brunswick.• During the past seven years, as ore reserves increased, the mill capacity was first expanded to 1,600 tpd and then to 3,000 tpd. In the last expansion, instead of building a completely new 3,000-tpd mill, or adding to existing installations, Heath Steele retained service facilities, buildings, ore bins, Jab, etc., and removed and replaced almost all existing process facilities. Requiring a complete mill shutdown, the expansion had to be carried out in minimum time. Also, new equipment had to fit into existing space. Critical path networks of the project were prepared, a tight schedule for construction was mapped out and progress charted daily to detect problems before they could interrupt the schedule. Heath Steele supervised the purchasing, handling and storage of new equipment, maintained liaison with the engineering contractor and became a sub-contractor, using its own staff to install all flotation equipment and process piping. The 1,600-tpd installation was dismantled and a 3,000- tpd unit was successfully put onstream in 5 months - on time and within budget. One benefit stemming from the expansion: production increased 87 per cent while operating and maintenance labour rose only 8 per cent."

Jan 1, 1972

By Lawrence Adler

For openings in bedded rocks, analyzed by simple beam theory, it has been shown that roof loads can be shifted from one support to another.' This transfer is effected by controlling the relative deflection of adjacent supports. If this action is used to reduce loads in the props or bolts and increase them in the ribs or pillars, it could be productive of economies averaging 30 pct. Such savings can be realized by: 1) using smaller artifical supports such as props and bolts, and 2) increasing loads in the rib to induce eventual failure for longwall caving. Since the rib is relatively load-insensitive, it provides a natural load sink. However, caution must be used in applying such permissive deflections, for while the supports are being handled properly, the stresses in the roof itself are very sensitive to such manipulations.'

Jan 5, 1960

By C. W. DeLong, L. L. Farnham, L. A. Stewart

This paper is one of a series covering mineral resources of the Nation . It describes briefly most of the known manganese deposits of eastern Arizona , which for the purpose of this report includes the counties of Navajo , Apache , Gila, Graham, Greenlee , Pinal , Pima , Santa Cruz , and Cochise . With few exceptions , these descriptions are the result of field examinations by the writers . Work on this paper was begun in May 1956 , and in the following 18 months 151 deposits were examined . The distribution of the deposits by counties is as follows : 1 in Navajo , and 1 in Apache , 37 in Gila , 4 in Graham, 13 in Greenlee , 25 in Pinal , 13 in Pima , 12 in Santa Cruz , and 45 in Cochise . In surveyed areas the locations of the deposits are described by section , township , and range and in unsurveyed areas , by approximate projections of these subdivisions . The township and range numbers refer to the Gila and Salt River base and meridian . The history, production, ownership , geologic setting , and mining methods used are discussed for most of the deposits that were visited . Probably , some occurrences have been overlooked , but all of the principal ones have been examined . Ore dressing studies were made of typical ores from several of the larger districts . The work was performed in the laboratory of the Bureau of Mines Tucson Metallurgy Research Laboratory . The results of these studies are given with the descriptions of the deposits from which the samples were taken .

Jan 1, 1961

By A. Jahedsaravani, M. Massinaei, M. Zarie

Deep learning is a subset of machine learning that uses artificial neural networks for extracting high-level features from image data. In the present study, a soft sensor is proposed for the prediction of the flotation performance through froth features generated by the use of pre-trained convolutional neural networks. Several state-of-the-art convolutional neural networks (AlexNet, GoogLeNet, VGGNet, ResNet, and SqueezeNet) pre-trained on the ImageNet database are used to predict the metallurgical performance of two flotation systems. The first case study is a batch copper flotation system video-captured over a wide range of process conditions. The second case study is an industrial coal flotation column equipped with a continuous video recording system. The pre-trained networks are used to extract features from the froth images, and these features are subsequently used to predict the flotation conditions and performance. The prediction results by the pre-trained algorithms were compared with the traditional image processing algorithms. This demonstrates the ability of the pre-trained structures to generalize to images outside the ImageNet database. GoogLeNet outperforms other network architectures and provides more accurate predictions of the flotation process behavior and performance.

May 5, 2023

By D. Harrington

During the 5-year period 1906-10 inclusive, 84 major disasters (a major disaster being one in which 5 or more lives are lost) occurred in the coal mines of the United States, or an average of 17 per year, and the total number of fatalities from coal-mine gas and dust explosions (major plus minor) for the 5 years aggregated 2,338 or 477.6 per year. The monotonous continuance of coal-mine disasters month by month aroused the people of the United States to such an extent that it was felt necessary for the Federal Government to try to do something looking to the avoidance of the admittedly excessive loss of life in our coal mines, and this was one of the deciding factors in the establishment of the United States Bureau of Mires in 1910. That results have been obtained in this particular cause of coal-mine accidents may be seen from the fact that for the year 1933 but one major explosion disaster occurred in the coal mines of then united States and the total number killed in that disaster was 7. Unquestionably the coal-mining industry through use of oaf or mining practices and aided by the various kinds of work of the Bureau of Mines looking to the prevention of mine fires and explosions is in large part responsible for this very creditable change. If the gas and dust explosion fatality rate of 1.059 per million tons of coal produced during the period 1906-10 inclusive had continued to the first of January 1934, instead of the 6,373 deaths which actually occurred due to gas and dust explosions, there would have been 13,480. Hence, during the 23 years existence of the Bureau of Mines there has apparently been a saving of about 7,102 probable deaths, or an average of more than 300 per year, from gas and dust explosions as against the number which would have occurred had the 1.059 gas and dust explosion fatality rate for the period 1906-10 continued. Thirty-nine persons were killed in all kinds of explosions (both major and minor) in the coal mines of the United States in 1933; if the 1.059 gas and dust fatality rate of the 1900-10 period had been in effect in 1933, about 400 persons world have been killed. Unquestionably, the various teachings of the U.S. Bureau of Mines looking to the avoidance of explosions and fires in mines have had a vital influence in reducing the number of explosions and fires and also in decreasing their destruction in case they occur.

Jan 1, 1934

By G. B. Atkinson

The Bureau of Mines investigated a method for increasing the leaching rate of bulk superalloy scrap to facilitate recycling and recovery of critical metals such as Ni, Co, and Cr. Three superalloys were investi- gated, the cast-nickel-base superalloy IN-738, the wrought-nickel-base superalloy Rene-41, and the cast-cobalt-base superalloy Mar-M-509. Superalloys melted with 20, 30, 40, and 50 pct Al metal to form inter- metallic compounds were easily crushed to a convenient particle size and reacted rapidly with acid solutions which dissolved the metals. For example, leaching 1/2-in pieces of unalloyed IN-738 with excess 6N HC1 at 95° C for 2 h dissolved about 0.5 pct, while leaching 10 g of minus 20-mesh 30 pct Al-70 pct IN-738 with excess 6N HC1 at 95° C for 2 h dis- solved 96.2 pct.

Jan 1, 1983