Search Documents

The man in the street (and no doubt most members of the Institute) thinks of wire, if he gives it any thought at all, as a most commonplace commodity. It is an accepted necessity, and like most necessities is taken for granted, unless a shortage in one or other of its multitudinous forms or products causes inconvenience.For many years Australia has ·been a large consumer of wire, particularly for fencing. With the rapid development of secondary industry the demand has increased in both size and character until at the present time much of the wire produced in this country is used as raw material for subsequent manufacturing processes. The call has been of so varied a nature that the Newcastle Wire Mills now turn out a greater variety of wire types than any other single plant in the world.In this paper, the aim is to provide a picture of the manufacturing, properties, and uses of wire. No attempt is made to cover the subject in any detail, as the field is much too broad for anything other than general treatment. Many phases, particularly in regard to manufacturing processes, are, therefore, dealt with cursorily, but it is hoped that the paper will, without delving too deeply into the technical aspects of Wire production, give a general appreciation of:- (a) How steel wire is made. (b) The remarkable physical characteristics obtained by judicious combination of chemical composition, heat treatment, and subsequent cold work. (c) The uses of steel wire.HISTORY.Best known of the early references to wire is that appearing in Exodus, where mention is made of gold wire being used for the sacerdotal robes of Aaron. However, the period in question, about B.O. 1491, is comparatively modern history as far as wire is concerned, for specimens believed to have been made about B.O. 4600 have been found. It is fairly certain that the Egyptians produced iron wire in B.O. 4000. Of particular interest is the

Jan 1, 1947

By Mingxia Liu, Hao Li, Qi Liu

"Laboratory batch flotation tests were carried out on fine (-20 µm) hematite to investigate the non-polar oil’s influences when sodium oleate, octyl hydroxamic acid, or oleyl hydroxamic acid were used as a collector. Batch flotation tests were performed with artificial mixed minerals (hematite:quartz = 1:1) under natural pH condition and kerosene was utilized as the model oil. The experimental results showed that kerosene emulsion behaved differently when used in conjunction with the three collectors. Kerosene helped improve the flotation when sodium oleate or oleyl hydroxamic acid was used as a collector. Nevertheless, it reduced concentrate weight yield, grade and recovery to a noticeable extent when octyl hydroxamic acid was used as a collector, especially at low dosages. In addition, single hematite batch flotation kinetics tests coupled with water recovery measurement were carried out to study the role of kerosene at different collector dosages. It was observed that water drainage and the resulting froth destabilization by kerosene was dominant at low collector dosages, especially in the flotation using octyl hydroxamic acid. At higher collector dosages, the water drainage and froth destabilization effect by kerosene was possibly counter-balanced by the higher hematite hydrophobicity and bubble surface tension gradient, which led to more stable froth layer.INTRODUCTION The minerals industry is facing a steady decline in ore grade, compounded by increasing complexity of mineral dissemination. As a result, the ore has to be ground sufficiently fine to have a suitable degree of mineral liberation, which produces large percentages of fine and ultrafine particles outside of optimal size range for ore dressing. Due to the unique characteristics of fine particles, i.e., small mass, high specific surface area, and problems such as increased solubility of complex minerals (Finkelstein, 1997; Finkelstein & Allison, 1976; Fornasiero & Ralston, 2005), high reagent consumption, fast surface oxidation in the case of sulfides (Collins & Read, 1971; Klassen & Mokrousov, 1963), severe particle entrainment (Subrahmanyam & Forssberg, 1988; Warren, 1984), low flotation rates (Glembotsky, 1953; Philippoff, 1952; Ye & Miller, 1988), slime coating (T. K. Mitchell et al., 2005; Parsonage, 1984), etc., flotation performance of these finely ground ores is very poor in terms of low concentrate grade and recovery."

Jan 1, 2017

By B. R. Mohal, S. Chander

"The adsorption and wetting behavior of freshly ground and aged coals has been determined in the presence of a nonionic surfactant. The amount of surfactant adsorption changes with the concentration and ""age"" of the coal. The freshly ground coal has smaller amounts of adsorption at lower surfactant concentrations than the ""aged"" coal whereas at large surfactant concentrations, the order is reversed . In the latter case, more surfactant is adsorbed on fresh coal than on the ""aged"" coal . . It is proposed that at low concentrations, the surfactant adsorbs through both hydrophobic and hydrophilic interactions with the molecule lying parallel to the· surface, whereas at higher concentrations surface micelles form at the hydrophobic sites. The wetting behavior correlates well with the adsorption behavior.INTRODUCTIONNonionic surfactants have many applications in the coal and mineral processing industry. They can be used as dispersing agents to modulate flotation, flocculation and filtration of particulates (1). They can also be used to increase the wettability of hydrophobic solids such as coal and can hence be used as dust suppressants (2,3). Although the adsorption of representative nonionic surfactants such as Triton N-101 (an ethoxylated nonylphenol with 9.5 moles of ~thylene oxide and HLB equal to 13.4) have been studied extensively on substrates such as calcium carbonate (4), silica (5) carbon black (6) and graphite (7), very few studies are available for coals. Coals differ from other substrates with respect to two important characteristics: 1) coal are porous and 2) coals consist of a patchwork of hydrophobic and hydrophilic sites (8). Since the adsorption characteristics of a surfactant are influenced significantly by the nature of the substrate the characteristics of the coals must be taken into consideration."

Jan 1, 1989

By William H. King

The Mining Division of the Bureau of Mines has been making development and power-requirement studios for the Interior Department Missouri Basin Field. Committee. The studies by the Bureau of Mines have as their purpose, the summarizing of potential future power requirements in the mineral industry within the Missouri Basin, special emphasis being placed on possible expansion of these requirements through construction of new mining enterprises by private capital. In preparing a proposal for the production of phosphoric acid from phosphate rock near Lander, Wyo., it was found that the basic information on the physical and chemical characteristics of the phosphate beds to determine costs of mining and treatment was lacking.

Jan 1, 1949

By P .. H. Grimley, N. Champigny

"Fourteen companies (Appendix) representing senior mining organizations in Canada were canvassed in order to assess: (1) the current usage and trends, and (2) the usefulness of computer applications in ore reserve estimation and grade control. The results of the questionnaire suggest that:• computers are unsurprisingly, predominant in the mining industry for calculating reserves and performing grade control;• time and cost savings are realized;• computer-based approaches are applicable to underground situations;• geological information is incorporated to the computerization process; and• computer usage does not hinder the collaboration of geologist and mining engineer.A clear need is identified for case histories comparing computer-calculated ore reserves and actual production data.IntroductionAmong the management and technical staff of some mining companies there is a perception that the application of computer based technology for the estimation of ore reserves and grade control, has as many drawbacks as benefits. Some of the objections raised against the utilization of computers for ore reserve estimation are that:• computer-based reserve models work for large open pit mines but not for underground situations;• computer-generated reserves ignore the geologist's knowledge base; they are strictly a number crunching exercise; and• the use of computers for ore reserves hinders collaboration between the geologist and mining engineer.In order to determine (I) the extent of current computer usage and future trends and (2) whether the objections noted above are borne out by experience, a number of senior Canadian mining companies were canvassed.The respondents were asked to provide:• an assessment of the importance of the computer in the ore reserve estimation and grade control process;• the level of involvement of individuals and staff groups with computer-based ore reserve estimation;• the advantages perceived and realized from the utilization of computer-based ore reserve approaches;• the current and future human resources requirements for the evaluation, implementation, maintenance and development of computer-based ore reserve systems;• the hardware and software resources presently used and planned; and• the developments needed to increase the use and acceptance of computer-based ore reserves."

Jan 1, 1990

By T. Sun, J. Kou, D. Tao

"The reduction behavior of low-grade lump hematite ore (100% 20-50 mm) has been evaluated by performing a series of coal-based direct reduction roasting tests followed by magnetic separation under different process conditions such as roasting time, temperature, reductant type and dosage, and grinding stage. To investigate mineralogical transformation and reduction characteristics of lump hematite ore, roasted ores and magnetic concentrates were analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM) with energy dispersive spectrometer (EDS) and polarizing microscope. The results have shown that a magnetic concentrate with a total iron (TFe) grade of 90.7% was produced at an iron recovery of 83.9% when lump hematite ore was reduced at 1,200° C for five hours using 35% lignite as a reductant followed by two stages of grinding, for 20 min and 30 min each, and low-intensity magnetic separation. The degree of reduction is closely related to the change in the internal structure of the roasted ore. Lignite with a higher fixed carbon content and lower ash generated roasted ore with a more highly porous structure, which provides better permeability of reducing gas. Magnetite, fayalite and wustite were the dominant intermediates of coal-based direct reduction of lump hematite ore. Parts of wustite reacted with SiO2 or Al2O3 in gangue and generated fayalite or hercynite. FeO in fayalite was replaced by CaO to produce wustite, which was finally reduced to metallic iron. However, Fe in fayalite and hercynite produced with low contents of CaO cannot be reduced into metallic iron. Introduction Low-grade hematite ore, characterized by low Fe content and high SiO2 content, cannot be treated by traditional mineral processing methods due to its nonmagnetic property and fine liberation size. The direct reduction (DR) roasting process has been studied and proven satisfactory in treating difficult-toprocess ores, such as low-grade nickel laterite oxide ore (O’Connor et al., 2006; Cao et al., 2010; Guo et al., 2011), high phosphorus oolitic hematite ore (Li et al., 2012; Yu et al., 2013), low-grade hematite ore (Wei et al., 2013;) and iron ore tailings (Li et al., 2010), which greatly expand the resources of usable iron ores (Srivastava and Kawatra, 2009). Therefore, the use of a DR process to treat low-grade hematite ore to produce direct reduced iron (DRI) is of great interest to many researchers of mineral processing and metallurgy (Weissberger et al., 1986)."

Jan 1, 2015

By W. L. Batt

MODERN war means mechanization, and mechanization means raw materials, especially minerals-and lots of them. Let me recall a few events of recent history-events that constitute mile- stones down the road to the war now blazing on three continents and threatening to spread still farther. In 1932, Japan took Manchuria, largely upon the excuse that she needed raw materials; in 1935, Italy invaded Ethiopia, largely upon the excuse that Mussolini's growing nation needed raw materials-in this case oil; from 1933 to 1935, Germany cried out for a greater share of the world's natural wealth, and since 1938 has invaded or occupied ten other countries, frequently upon the excuse that she needed-and had a right to-more raw materials.

Jan 1, 1940

Cyanide is reactive to copper minerals and is not suitable to extract the gold from the copper bearing ores. Ammoniacal thiosulfate is considered an excellent alternative lixiviant for leaching copper bearing gold ores. Unfortunately the results of high reagent consumption and poor gold ex-traction were found by thiosulfate leaching of synthetic gold ores containing chalcopyrite, chalcocite or bornite and a mild refractory copper-bearing sulfidic gold ore. In this investigation, several processes have been applied to reduce the impacts of these minerals on gold leaching. The process included: the pre-oxidation of copper sulphide minerals in water or ammonia solution, the reduction of dissolved oxygen in the lixiviant (0.3 ppm DO or 0.7% oxygen), adding phosphate anion in the leach or pre-leach stage, and the addition of a strong copper ligand (e.g., EDA and DETA). The results indicated that the gold extraction could be improved to 93% with the thiosulfate consumption being reduced to less than 8 kg/t. The dissolution of copper minerals was found to be the major reason for increased consumption of thiosulfate and the highly reductive leached surfaces are responsible for the reduced gold extractions.

Jan 1, 2014

By A. J. Stosick, J. R. Hoffman, E. Rudy, St. Windisch

The binary alloy system Mo-C zoas investigated by means of X-ray, metallog/aphic, thermoanalytical, and melting-point techniques on chemically analyzed specimens. The system, Fig. 39, is characterized by three congruently melting, intermediate phases, Mo2C, n MoCi-x, and aMoC1-,, of which only Mo,C is stable at temperatures below 1650°C. Substoichio-metrzc (~32.5 at. pct C) dimolybdenum carbide undergoes a homogeneous sublattice order-disorder transformation at temperatures of approximately 1400°C, whereas hyperstoichiorrletric compositions undergo a discontinuous Phase change. The order-disorder transitions in the Me, C phases are discussed in terms of the structural changes involved in the transformation processes and the absence of long-range sublattice coherency in stoichiometric or hyperstoiclziomet-ric compositions attributed to the impossibility of obtaining long-range order in a linear chain of alternating carbon atoms and vacancies. From the experimental phase relutionships and the known thermody-namic data for Mo2 C, limits for the free energies of formation for the high-temperature phases r) MoC1-, and aMoC1-, are deriued and found to be in good agreement with data previously obtained from phase equilibria in ternary metal-carbon systems. IN the course of studies of the high-temperature phase relationships in ternary systems of refractory transition metals with carbon,' a number of inconsistencies found in previous work necessitated a reex-amination of some of the related metal-carbon binaries. A reassessment of the binary system data also seemed

Jan 1, 1968

By Wolfgang Baum

Remediation work on thermal process dusts and slags has been primarily based on chemical analyses. These data offer little information for the assessment of treatability and reuse potential. In addition, the lack of mineralogical residue characterization has frequently caused time-consuming and inefficient waste management. This paper will outline the cost-effective, and sucessful use of process-oriented mineralogical analyses for treatment and beneficial reuse of various thermal residues. These include a patented process for detoxification of Pb-contaminated bottom ash, the pyrometallurgical treatment of K 061, the reprocessing of lead smelter slag as well as various power plant residues.

Jan 1, 1992

By Shu Xinqian, Zhou Weining, Shan Zhiqiang, Feng Jifu

"Modified calcination conditions on the extraction of rubidium resources from muscovite (KAlz[AlSi301o](OH)2) ore are systematically studied. The impact of various factors on the rubidium leaching rate is also analyzed, including the agent types, roasting time, the mass ratio, roasting temperature, etc. The results indicate that the best agent is a combination of sodium chloride and calcium chloride, its mass ratio ofmuscovite/NaCl/CaClz is 1:0.25:0.25. Calcined at 8500 for 30 minutes, the rubidium leaching rate is up to 90%. The reaction of muscovite ore with the chlorinating agent CaC12 has been studied by TG/DSC, the calcined intermediates are identified by XRD, and the surface morphology before and after leaching is characterized by SEM. Rubidium chloride products can be obtained with a purity of 92% by using t-BAMBP extraction, hydrochloric acid reextraction and purification.IntroductionRubidium is one ofrare alkali metals, which is found in 1981 by German R.W. Bunsen and G.R. Kirchhof. Rubidium includes the following features: atomic number is 37, each atom weight 85, the body-centred cubic lattice, each unit cell has two metal atoms, and the density is 1.532g/cm3. The properties of low melting point (312.46 K) and malleability make rubidium have a strong chemical activity and photoemission. Rubidium provides a main material for manufacturing phototube with a wide range oflight waves, which possess high sensitivity and stability. Efforts are being made to carry out research on rubidium ion gngine, magnetic flux generators and thermoelectric transudcer, etc. Rubidium exists in muscovite ore(KA12[AlSh01o](OH)2 (monoclinic system and hexagonal layered structure) as isomorphism and replace the large radius of the potassium atoms, as well as part of rubidium locate between structure layers. The complex components bring great difficulty in comprehensive recycling."

Jan 1, 2013

By E. W. Shaw

The past year (1950) has been a big one for the oil industry in Canada, with new records being set in almost every phase of exploration and development activity. New highs were reached in acreage holdings, in geophysical activity, in wildcat drilling, and in field development and production. The only item that did not show a substantial increase over recent years was the amount of reserves added by new discoveries. This was not due to a decrease in the number of new discoveries, however, hut rather to the fact that most of the discoveries were made during the later months in the year and could not be fully evaluated by the year end. The foregoing remarks pertain mainly to activity in Western Canada. In Eastern Canada, operations continued on a modest scale. with exploration drilling down slightly from the previous year but with development drilling and production at about the same level. Returning to Western Canada, it is observed that the general exploration play was one of expansion and intensification. The issuing of new petroleum and natural gas regulations by the province of British Columbia precipitated a moderate entry of companies into the northeastern part of the Province.

Jan 1, 1951

Domestic production of pyrite cinder reached 15.95 million tons in 2006. The pyrite cinder used in cement industry accounts for about 30% production. The remaining 70%, 11.17 million tons, was thrown away as waste, which brought serious environmental and resource problems. A new technology of composite pellet reduction-roasting and magnetic-separation (CPRM) has been developed to utilize pyrite cinder. Pyrite cinder sample, containing 45.56% Fe, 0.19% Cu and 1.45% S, was pelletized with addition of 5% composite agent in balling disc. Green balls after drying were reduced at 700~800 ? for 20min with 300kg/t pulverized coal injection in rotary kiln. After two stages of ball-grinding and four stages of magnetic separation, high grade magnetite concentrate with 66.23% Fe was produced, meanwhile impurities Cu and S was decreased to 0.048% and 0.053%, respectively. And iron recovery of 73.32%, desulphurization of 96.34% and decoppering degree of 74.73% were achieved. Key technique is that composite agent can accelerate reduction of Fe2O3 and transfer copper and sulphur into water-soluble inorganic salts, which can be removed during wet magnetic concentration. This new technology can be used to fully utilize pyrite cinder and produce high quality magnetite concentrates as feed for steel industry, which will help tackle the pollution problem of pyrite cinder and extend iron-bearing raw material sourcing for Chinese steel industry.

Jan 1, 2014

By A. O. Dufresne

Introductory At the Annual Meeting of the Institute, held two years ago, I had the privilege of presenting a paper on Recent Mineral Discoveries in Western Quebec. In it were pointed out the areas favourable for prospecting in that section of Quebec adjoining the mining camps of northern Ontario; the discoveries that ?had been made were recorded; and some of the developments up to that date were reviewed. Since then, two full years have elapsed, during which a considerable amount of serious work has been performed with such results that western Quebec has today six properties about ready to mine commercial ores of gold, copper, and zinc. These results have been brought about after large sums of money had been invested to bring the district to a producing stage. A smelter has been built, and is already producing copper; two railways have extended their lines into Rouyn; and the Provincial Government has shown faith in the future of the district and has spent large sums of money in the building of highways and for other public works. The purpose of the present paper is to review the developments of the last two years, and the work that has been performed in various spheres of activity in that section on western Quebec covering the county of Abitibi and the northern part of the county of Temiscamingue.

Jan 1, 1928

By J. D. T. Steyl

Anglo American Corporation and the University of British Columbia have developed a medium-temperature oxygen pressure leaching process for the extraction of copper from chalcopyrite concentrates in an acid-sulphate system (AAC/UBC process). Leaching is performed at 150°C and surfactants are added to disperse molten elemental sulphur from the unreacted sulphide surface to prevent liquid sulphur occlusion. Copper extractions of over 95% and elemental sulphur yields of around 60% were observed over a 2-hour average residence time in a continuous pilot autoclave. Sporadic blockages occurring under continuous conditions were found to be caused by the accumulation of molten elemental sulphur mixed with unreacted sulphide mineral. A batch programme of experimentation was undertaken to establish the reason for this phenomenon. Batch experiments were conducted at low pulp densities on concentrate samples with narrow size distributions and at similar solution compositions to those experienced in the pilot autoclave. The overall rate of chalcopyrite oxidation was shown, under approximately constant solution composition, to be a strong function of the total available mineral surface area. Initial copper extraction rates followed the shrinking particle kinetic model under intrinsic surface control. Deviation from shrinking particle kinetics was however observed after a certain oxidation time. Secondary electron images identified small (typically less than 20 µm) sulphur conglomerates at the point of deviation, which 'collected' unreacted chalcopyrite mineral particles and lowered the total mineral surface area available for oxidation. These sulphur clusters are thought to be the precursor for blockages experienced in the continuous pilot autoclave. These results emphasised the importance of fine grinding (P80 5-20 µm) and suggest that shorter residence times may minimise the formation of sulphur conglomerates in a continuous autoclave operating at medium temperature.

Jan 1, 2004

By U. Ulusoy

Surface roughness and acuteness are known as the two of the main properties of the particle morphology affecting the behavior of the powders in the process. Since the techniques used for the morphological characterization of powders by 2-dimensional microscopic measurement from the polished sections that have some disadvantages, the 3-dimensional analysis has often relied on measurements of particle morphology. A review of literature data was presented for high-grade barite and pyrite particles ground by ball and autogenous mills to determine the morphological properties using a new 3-D approach based on BET nitrogen gas adsorption and Permaran methods. Micromeritics Flowsorb II 2300 instrument which employs BET nitrogen adsorption technique was used for the specific surface area measurements and the roughness of the particles. Permaran (manufactured by Outokumpu Oy) was used for the measurements of airflow resistance of powder samples for the acuteness. Spherical glass beads were used as reference sample for the acuteness measurements. The obtained parameters, which are surface roughness and acuteness, were corre-lated with the floatability performance of those mineral particles. The flotation performances of those particles ground in different mills (ball and autogenous) were also evaluated by a Hallimond tube. The results showed that lower roughness and acuteness values caused higher flotation recoveries for both barite and pyrite particles that were tested independently in different type of the mills. In other words; particles with smooth surfaces resulted in better floatability for barite and pyrite minerals studied.

Jan 1, 2014

By Edmar de Souza Silva, Antonio Augusto Gorni, Emanuelle Garcia Reis, Daniel Bojikian Matsubara

Controlled rolling followed by accelerated cooling, known worldwide as TMCP, aims to increase mechanical properties without toughness deterioration. The process principle is to promote the plate cooling with water jets along the range of the austenite transformation temperatures. The accelerated cooling process is only fully effective when controlled in an integrated manner, as it alone cannot ensure significant improvements in the final properties of steels. Plate surface quality depends on some parameters that must be controlled before the start of the plate accelerated cooling. Good flatness is essential to avoid irregular water accumulations during cooling. After the reheating process, the slab should have uniform temperature, uniform austenitic grain size and easily removable scale. The slab thermal and microstructural heterogeneities are inherited by the rolled plate and tend to increase further during the accelerated cooling. This results in flatness problems, high level of internal stresses and mechanical property variations. The descaling strategy is an extremely important factor and must be determined with great caution. It is important that scale thickness and distribution is uniform to ensure homogeneous cooling over the entire plate surface. Otherwise, there will be an uneven temperature distribution, which can cause serious problems of flatness, surface quality and mechanical properties.

Oct 1, 2019

The last twenty years of development in Process Mineralogy are reviewed. Since the milestone review by Henley in 1983, which projected the concept and suggested closer working relations between mineral processing and mineral science, the second generation (1983-2003) has made significant progress. Examples are to be found in improved sampling and high-confidence flotation testing, and in automated quantitative mineral measurement. The recent addition of end-member studies has provided a clearer view of the overall ore mixture milled from its constituent geological components. In all, better predictive abilities have resulted from these improvements to Process Mineralogy. These improvements have led to more significant business impacts in mineral resource characterization, and in optimization of existing concentrator operations.

Jan 1, 2004

By Hans W. Schreiber, Rudi P. Fronk

IINTRODUCTION Widespread activities in precious metal projects in the western U.S., Australia, Canada and other parts of the world have opened a flood-gate of consul- ting expertise to aid and accelerate the development process. Utilization of outside expertise has taken on many shapes and forms that have in some instances actually "decelerated" or "retarded" project progress. Small mines are especially vulnerable to apparent false-starts and misdirections, be- cause of their generally lower capital commitments, shorter lead times and limited mineral in-house expertise. Mine development for small mines requires fundamental approaches by knowledgeable consultants that are timely and cost-efficient and in line with accelerated development, if they are to be successful. The development process is obviously that process which brings a given deposit into production. Or, put another way, the process comprises all activities, decisions and commitments which take place from the moment an authorizing entity (usually a board of directors) com- mits to development and production (usually on the basis of a final feasibility study) until the first ton of ore is processed to a saleable product. The activities, decisions and commitments over a development period--such a period can range from as short as a year or less to as long as 5 years or more--are many, highly varied, and often interdependent. The development period is also particularly risky, not only because of the varied and interdependent decisions and commitments, but also because of capital demand amounts. Delays in the development process are thus particularly costly - sometimes so costly that small and often undercapitalized mining companies, failing to reach production and a cash flow within a planned period, face, if not bankruptcy, at least severe equity dilution or particularly onerous and restrictive covenants on additional loan financing. It therefor behooves especially small mining companies to examine ways to accelerate development. By doing so, the development process may actually meet planned scheduling. The development process generally comprises environmental impact studies completion, final engineering, permit- ting, financing, equipment and machinery procurement, contractor selection and construction -- such activities largely being overlapping. The paper addresses what the small mines operator or the small mining company can do with consulting firms to accelerate development. By "small mines" is meant open pit operations of 2000 tpd or less and underground operations of 500 tpd or less. By "consulting firms" is meant entities who do not possess an engineering and construction capability, such as Derry Michener Booth & Wahl, Pincock Allen & Holt, Behre Dolbear-Riverside, etc. The paper concentrates on gold projects. PRIORITY CONSIDERATIONS Of the items listed in the previous paragraph which comprise the development process, the two which most consistently appear to cause delays are permitting and financing. The former's delays can be due to political overtones and thus the delays may not be reasonably foreseeable. The latter's delays are most often due to inadequate preparation, and thus are avoidable. For the reason stated above, and considering that financing is fundamental to all of the activities which constitute the development process, the paper focuses on financing as the priority item which can most assist in accelerating or retarding the development process.

Jan 1, 1987

By J. -F. Blais, M. -O. Simonnot, J. Mocellin, G. Mercier, J. -L. Morel

Large quantities of ferromanganese sludge are generated as waste material by blast furnace during the manufacturing of ferromanganese. These slags are very rich in manganese, zinc and lead (5 to 40 %). These residues have been deposited in a pond in periphery of the steel industry. Considering the market value of the metals, these brownfield sites can now be considered as secondary resources. We have developed a hydrometallurgical process for selectively leaching Zn, Mn and Pb in order to produce compounds of Mn and Zn pure enough to be economically recoverable and a residue rich in Pb. Batch laboratory experiments were carried out to determine appropriate leaching conditions to maximize zinc extraction (100 %) and manganese extraction (90.0 %) with sulfuric acid and to generate a residue containing 15 to 30% of lead. This Pb residue is recyclable by another process.

Jan 1, 2015