Search Documents

By J. O. Marsden

Parts I and II in this series of papers presented the chemistry of medium-temperature pressure leaching of copper sulfide concentrates and reviewed the metallurgical development of a process to effectively recover copper using medium-temperature pressure leaching and direct electrowinning (DEW). Key features of the process were the use of superfine grinding of the concentrate (to a P98 of 12 to 15 µm and P80 of 6 to 7 µm), pressure leaching at 160ºC and 1,380 kPa (200 psi) oxygen overpressure, DEW to produce LME Grade A cathode, recycling of the lean electrolyte to the pressure leaching step and treatment of a lean electrolyte bleed by solution extraction (SX). Recycling of the lean electrolyte provided all of the acid required to effectively dissolve copper and convert approximately 65% to 70% of the sulfide sulfur to elemental sulfur, resulting in an ?acid-autogenous? process referred to as the ?MT-DEW-SX? process. This paper (Part III) discusses the steps taken to develop and complete a large-scale demonstration of the process at Bagdad, Arizona, in 2005.

Jan 1, 2007

By Hamid Maleki

A comprehensive study consisting of stress determinations, core logging, laboratory testing, and numerical analyses was conducted to investigate the cause and potential alternatives to the coal bump conditions that developed in the Second North Panel of the Little Dove mine near Buntington, Utah. Roof rock characteristics were such that a cave did not develop above this 420 ft wide panel. After 700 ft of pillar retreat, severe coal bump conditions developed during pillar mining. The coal bump conditions resulted from excessive pillar stress which was caused by load transfer from the extracted, noncaving, portion of the panel. Site specific data and numerical modeling techniques were used to back-analyze the bump prone condition. This back- analysis lead to the identification of critical stress, closure, and energy release levels. These critical levels were then used to evaluate alternative pillar mining sequences in the hope that the potential for coal bumps could be reduced. It was found that while alternative sequences offered some potential improvement over the pillar mining sequence used in the mine, alternative pillar mining sequences would not significantly reduce the potential for bumps. For the roof characteristics at this mine, coal bumps are best avoided by developing narrow panels or significantly wider panels, which incorporate properly sized barrier pillars. Narrow panels, on the order of 300 ft, would not cave, but panel pillar stresses and the potential for umps would be moderated by the reduced r' panel width. Wider panels, of approximately 650 ft, would allow a cave to develop, also reducing panel pillar stresses and coal bump potential.

Jan 1, 1987

By A. Akcil, O. Celep, C. Erust, E. Y. Yazici1, H. Deveci1

"Recycling of WEEE has already gain prime importance from both environmental and economic point of view. For the recovery of metals from e-waste, many conventional physical, bio/hydrometallurgical and pyrometallurgical processes are proposed. Economic potential of e-waste is mainly driven by its precious metal content. Physical separation methods (e.g. electrostatic, magnetic, eddy current and gravity separation) exploit the differences in the physical properties of metals and non-metals. Physical separation methods are simple and economically sound but they suffer from metal losses and ineffectiveness at fine sizes. Hydrometallurgical processes are promising owing to their relatively low cost, reduced environmental impact, potential for high metal recoveries and suitability for small scale applications. Hydrometallurgical processes can be developed for selective extraction of base/precious metals using suitable reagent systems. Sulphate-based leaching with a suitable oxidant (e.g. H2O2, O2, Fe3+) is effective for copper and other base metals. After removal/recovery of base metals, precious metals can be easily extracted using various lixiviants including thiosulphate, thiourea, cyanide and chloride. However, further research is required to develop new, cost effective and environmentally friendly processes and/or refine existing ones for leaching and, in particular, downstream processes. INTRODUCTION Electrical and electronic equipments are indispensable to modern societies with numerous applications in the field of medicine, transport, communication, education, security and environmental protection. With technological developments and innovations, the replacement of old equipment leads to ever fast accumulation of waste materials such as waste electrical and electronic equipment (WEEE or e-waste). People are upgrading their mobile phones, computers, televisions, audio equipment and printers more frequently than ever before (Babu et al., 2007; Lee et al., 2007). With the rapid growth in technology today, the life span and utilisation period of most electronic and electrical equipment has been reduced considerably with concomitant generation of huge amounts of WEEE over the past several decades. According to statistics presented by Balde et al. (2015), total WEEE produced around the world was 41.8 million tonnes in 2014 and expected to rise to approximately 50 million tonnes by 2018. Kumar et al. (2017) estimated that annual growth rate for the WEEE stream is 3–5% (Singh et al., 2016). The aim of this paper is to provide an overview of physical separation and hydrometallurgical methods available for the treatment of WEEE."

Jan 1, 2018

By Roy Lindsay, Paul O'Hara, Gary Halverson

"The New Britannia Minesite is located in Snow Lake, Manitoba, 420 miles north of Winnipeg (figure 1). The mine previously operated from 1949 to 1958 extracting some 5.39 million tons of ore at a 0.150 opt gold grade. From 1959 to 1986 the property was held by Nor-Acme and Hudson Bay Exploration and Development and in 1987 High River Resources Ltd. Optioned the property, dewatered the mine and conducted a diamond drill program between the 1 780 and 2400 levels. In 1988 two companies, Nor-Acme Mines Ltd. and High River Gold Mines Ltd., negotiated an option agreement with INCO Gold whereby !NCO assumed management control of all site exploration work. During this period, a bulk sample of 10,000 tons was extracted from the 1780 level with no further exploration recorded after its removal. Both Hudson Bay Exploration and Development and INCO Gold conducted feasibility studies on reactivating the property but at a calculated capital cost of Cdn $70 to $80 million found the rate of return on their investment unacceptable.In 1991 !NCO Gold merged its interest with the assets of TVX Gold Inc. and in February 1994 TVX Gold Inc. and High River Gold Mines Ltd. entered into a joint venture partnership to develop the Snow Lake property, naming TVX Gold Inc. the operator. Upon completion of a feasibility study in April 1994 by Bharti Engineering Associates Inc., a decision was made to reopen the Britannia Mine at an established project cost of US $33 million.Project construction commenced in July 1994 with the hoist house excavation. The first concrete for the hoist house level footings was poured on August 4, 1994 and the project was completed on October 1, 1995 at a cost of US $36 million. The first gold pour took place November 4, 1995.This paper not only presents the metallurgical aspects of the operation but also describes the novel approach used to complete the design and construction of the site facilities."

Jan 1, 1996

By H. S. Marshall

Optimum Colliery is an opencast strip mine producing 18Mt of bituminous coal per annum for the export and inland markets as well as for domestic power generation at the Hendrina PowerStation. Coal is exposed by four 60m3 and four 11m3 walkingdraglines and transported from the open cuts to the processing plants by twelve 130 ton coal haulers. Overburden and interburden areas are drilled by nine 250mm-diameter rotary drill rigs. Until 1997 all surveying tasks were conducted by electronictotal stations requiring accurate control points from which line-of-sight XYZ readings could be taken. In 1997 a GPS system was introduced which consisted of a fixed base station and two rovers. The rovers were able to perform most of the survey tasks assigned to total stations. In addition, two overburden drills were equipped with blasthole drill navigation systems, which includes the drill monitoring and material (strata) recognitions system. The rest of the drilling fleet will also be equipped with GPS systems. Blasthole positions are designed in the office based on survey and geological/geophysical information and transmitted via radio link to an industrial PC on the drills. Together with GPS positional data, both the planned and actual drill positions are displayed on an LCD screen. This eliminates the need for surveyed hole positions to be staked before drilling, and for actual hole positions to be surveyed after drilling. As holes are drilled, performance and rock property data transmitted back to the office. Future applications will include GPS monitoring of dragline positions and pad elevations. GPS receivers on the draglines will utilize the existing base station to calculate and transmit XYZ co-ordinates. Another application will be locating of boreholes in the field prior to the pumping of specified explosive charges into the blastholes. Charging instructions for each blasthole will be loaded into the computer on the explosives truck which will be equipped with a GPS system for hole identification.

Jan 1, 1998

By Robert H. King

An analysis of low-voltage shielded trailing cables is performed to develop a method for calculating the differences in operating costs between shielded and non-shielded cables. Two types of shield constructions are considered (SH-C and SH-D) for the three major underground coal mining methods. Data from laboratory and in-mine testing are presented in addition to an analysis of safety benefits. Recommendations for further investigations are proposed. Example calculations with sensitivity analyses are presented. Recommendations for further investigation include costs impact considerations.

Jan 1, 1980

By G. W. Center

This manual is intended to assist federal, state, and local regulatory and planning agencies, the mining industry and consulting engineers in determining the regulatory, environmental, technical and economic constraints influencing the site selection, planning, construction/operation and reclamation phases of a waste disposal facility. The information presented illustrates that factors affecting an individual site may be simple or very complex. This manual discusses methods for making future land use decisions, determining regulatory requirements, evaluating physical, chemical and structural properties of the disposed waste and selecting appropriate waste disposal methods and control techniques. Procedures and guides in the manual will assist personnel in assessing the complexities of waste disposal on a site specific basis. The major types of waste disposal systems are discussed and evaluated in terms of their advantages and disadvantages and applicability to varying site conditions and waste characteristics. Appropriate references following each chapter provide more detailed data on material presented in the text.

Jan 1, 1982

By F. L. Pirkle, W. C. Bagby

"In his 1989 book, The New Realities, Peter F. Drucker, Clark Professor of Social Science at Claremont Graduate School, Claremont, CA, stated: “Information is data endowed with relevance and purpose. Converting data into information thus requires knowledge. And knowledge, by definition, is specialized” (p. 209).The discipline of mineral valuation is knowledge-based and requires a mineral valuer to collect, analyze and interpret data that are material to a mineral-valuation assignment. In so doing, the valuer turns the data into information (data come first, followed by information as determined by the mineral valuer) for use by the client (from whom the valuer obtained the mineral-valuation assignment) and other intended users. The valuer uses his or her experience and education (each valuer’s knowledge base) supported by a foundation built upon competency, materiality and transparency, the three pillars of mineral valuation (minerals valuation, mineral-property valuation).The International Mineral Valuation Standards Template (IMVAL Template), third edition dated May 2018, defines mineral valuation as: “The estimation of the value of a mineral property in money or monetary equivalent. The word ‘valuation’ can be used to refer to the estimated value (the valuation conclusion) or to refer to the preparation of the estimated value (the act of valuing)” (p. 14).Furthermore, the IMVAL Template clearly separates valuation from evaluation: “The template deals with valuation, which is distinct from evaluation. The distinction inherent in these defined terms is that valuation addresses the estimation of value of a mineral property, whereas evaluation addresses the broader assessment of a mineral property for an investment decision (p. 2).”This is an important difference because the minerals industry commonly makes investment decisions using feasibility studies to evaluate a proposed mineral development and production project. The purpose of such investment-decision analysis is distinctly different from valuation of a mineral property, no matter where that property lies upon the mineral explorationdevelopment- production-reclamation timeline (Fig. 1). Valuation involves terms such as market value, just compensation, fair value, etc., whereas investment-decision analysis is concerned with the economic viability of a given proposed project. Although feasibility analysis and market valuation can both use discounted cash flow (DCF) analysis as a tool, the formulation of the DCFs and their interpretation are different."

Nov 1, 2019

By Peter Radziszewski

"Typical mining operating costs can be divided between extraction (30 % to 70 %), comminution (30 % to 50 %) and separation (5% to 20% ). Cornminition process costs, representing an important contribution to mining operating costs, can themselves be divided roughly between energy (50 %) and linerkharge wear (50 %). Developing the ability of predicting mill wear will allow a more accurate estimation of wear costs. However, total media wear in a given ball mill grinding process is a product of three recognized wear mechanisms those being abrasion, corrosion and impact. Further, the contribution to total media wear of each of these wear mechanisms has not been well established. In this paper, a overview of abrasive, corrosive and impact wear mechanisms is made from which an empirical wear prediction procedure is proposed. Further, future directions in wear prediction research is outlined. INTRODUCTIONTypical mining operating costs can be divided between extraction (30 % to 70 %), comminution (30 % to 50 %) and separation (5 % to 20 %). Comminition process costs, representing an important contribution to mining operating costs, can themselves be divided roughly between energy (50 %) and lined-charge wear (50 %). With respect to wear, world wide steel consumption as grinding media is estimated at over 600 000 tomes per annum (Malghan, 1982). As such, developing the ability of predicting mill wear will allow a more accurate estimation of wear costs.Charge media wear prediction is actually estimated using the Bond abrasion test. From Bond abrasion index tests, it is possible to determine a wear rate using the following function:"

Jan 1, 2000

By Ziyad Abunada, David O’Connor, Abir Al-Tabbaa

"Abstract Contaminated land remediation using soil mix technology (SMT) is a relatively recent development which has been shown to be a cost effective and versatile system with numerous environmental advantages over other remediation techniques. The added complexities and variability associated with contaminated sites has escalated the need for field trials, field monitoring and specific QC measures to be undertaken for this setting and was the rationale behind project SMiRT (Soil Mix Remediation Technology). The main aim of project SMiRT was field validation, testing and assessment to provide stakeholder confidence in SMT and increase its uptake for land remediation in the UK. The field trials involved the treatment of 800 m3 of soil, through applying six different remediation techniques with four different SMT systems and introducing over thirty binders and binder compositions with a range of installation methodologies. Various issues were faced during the installation process and which were addressed on site. This paper presents some aspects of early age field observations, field monitoring, in-situ testing, coring and laboratory testing of cored samples and highlights some lessons learnt, providing valuable information on the issues that need to be addressed for this application of SMT.IntroductionAlthough soil mix technology (SMT) was developed in the 1960s in Japan and Sweden for geotechnical applications, its potential in geo-environmental applications became evident more recently the 1980s in the US and in the 1990s in Europe, having since increased to provide a range of remediation systems (Al-Tabbaa and Evans, 2003; Al-Tabbaa et al., 2011). The most common applications to date have been (a) the construction of low permeability containment walls or cut-off walls to contain a contaminated site; (b) stabilisation/solidification (S/S) treatment, with cementitious binders, for physical and chemical encapsulation of contaminants in soils and (c) the installation of permeable reactive barriers (RPBs), which are permeable walls that intercept the groundwater flow and remove contaminants from it, by mixing special additives with the native soil. Contaminated land remediation using SMT is a cost effective and versatile approach with numerous technical and environmental advantages over other remediation techniques. These advantages include the use of simple and well established techniques and equipment, speedy implementation, applicability to sites of any size and to multiple contaminants, elimination of off-site disposal, low risk and low emissions. There is a lack of competing alternative technologies that offer the same level of versatility and economic, environmental and social benefits, under current environmental legislation constraints. In addition, most currently available contaminated land remediation techniques are only partially effective, and are relatively contaminant-specific. This makes SMT a promising and timely contender to lead the market place in offering a cost-effective, efficient and low risk solution to contaminated soil and groundwater remediation and has resulted in a range of recent innovations."

Jan 1, 2014

Old Copper Flotation Tailings Waste Reprocessing

Sep 13, 2010

By Hayel M. El-Naggar, Sherif A. Akl

Although grouted piles have been used for several decades since the idea was proposed in the 1970s, their design is mostly based on experience and unpublished proprietary methods. There is little research on grouting drilled shaft tips and even less on grouting shaft sides. This paper presents the analysis of 4 instrumented pile loads tests on base and shaft grouted piles from different sites in Egypt; with emphasis on one of the tests, to demonstrate the analysis process. The data from the tests are analyzed to model the development of unit side friction (USF) with relative displacement. A numerical model using the finite element software PLAXIS is used to investigate the effect of grouting on the surrounding soil stress state. The paper combines the observations from full scale pile load tests and results from the numerical model to suggest an idealized behavior of side friction development with relative displacement of the grouted part of the shaft. The suggested model considers an envelope of Unit Side Friction (USF) with relative displacement, initially dominated by the grout resistance then at higher relative displacements, the friction with radially pressured soil takes over. The grout provides very high USF values up to a relative displacement of 2mm. Then, the USF drops to a typical pile soil side friction behavior; however, this friction is affected by the contact stress between pile and soil, which significantly increases due to compaction grouting. INTRODUCTION Base and shaft pile grouting has been significantly developing in recent years to accommodate the unfavorable conditions in major projects such as the high loads in high rise building and founding on problematic soil formations. Grouting aims to decrease settlements and increase the capacity of the pile under axial load. The technique is first introduced by Kraft (1974) but gained popularity in the 1980s. Typically there are two types of grouting; compaction, and permeation. Compaction grouting is more common in pile foundations practice, and many researchers have provided case histories of pile load tests on base grouted piles and base and shaft grouted piles (Gouvenot and Gabaix,1975; Stocker, 1983; Ghazali et al., 1988; Fleming, 1993; Kusakabe et al., 1994; Robson and Wahby,1994; Joer and Randolph, 1998; Hamza and Leoni, 1998; Mullins et al. 2000; Littlechild et al., 2000; Suckling and Eager, 2001; Dapp and Mullins, 2002; Ho, 2003; Fu and Zhou, 2003; Brettmann and NeSmith, 2005; Ruiz, 2005; Mullins, 2006; Dapp and Brown, 2010; Beadman et al., 2012; Nguyen et al., 2013; Miller et al., 2013; Sinnreich and Simpson, 2015; Hui and Lin, 2015). Compaction grouting is meant to densify the soil around the pile and below the base rather than permeate this soil and increase its cohesion. Research showed that grouting increases the capacity of the piles by a factor of 2~5. The variation in capacity increase depends on pile type, grouting process, and especially grouting pressure. Although there are many case histories of pile load tests on grouted piles but there is no well-defined agreed-upon method to predict grouted pile capacity as typically done in ungrouted piles. Few lab experiments discussed the shaft grouting effects on the soil especially the compaction grouting. The experiments concluded that the compaction grouting forms a homogeneous layer between the pile and the soil, and a residual effective stress is achieved simultaneously with a significant densification of the soil around the pile with noticeable decreasing in void ratio. (Fattahpour et al., 2015; Wang et al., 2015). Recently, studies used numerical analysis to investigate the behavior of the grouted piles and the changes in the surrounding soil (Chiang et al., 2013). That study presents a simulation of the base pressure grouting with a simple FE model and predicts the reduction of the pile settlement by 10 to 20%. Another numerical study using a complex model conducted by Zhou et al. (2017), pr

Jan 1, 2018

By Lutz Markworth, Evren Ören

"The worldwide demand of ores and the depletion of the high-purity deposits make it necessary to recover ores in increasingly finer size fractions in the feed material. The flotation technology of more than 40 years old plants was not able to recover the ultra fine material. Those slurry tailings ponds now have the chance to be re-processed with PNEUFLOT® technology.The bubble sizes of different flotation technologies have a huge influence of the results especially regarding the recovery of the ultra fine particle sizes.PNEUFLOT® technology of HUMBOLDT WEDAG Coal & Minerals Technology GmbH in Germany was applied to ultra fine Phosphate, Copper and Platinum ores. The results will be presented in this paper.Conventional technology like agitator flotation has its limits in the flotation of fines due to turbulences in the cell. The position of the agitator influences the recovery of the fines. A deep impeller generates a higher froth zone. This helps to catch the medium fines. Due to the static head of the slurry inside the cell, compressed air is required for such cell designs.Column flotation is well known for a good selectivity without having in the first cell a good recovery. This leads to invest in several cleaning stages to reach an acceptable recovery. Further more, compressed air is required to generate the air bubbles to the flotation process, which are much bigger than with PNEUFLOT® technology applied.INTRODUCTIONHigh metal prices are actually the basis to invest in poor deposits or deposits with very fine intergrown ores which have to be milled down to ultra fine powders less than 60 micron. The liberation grade has to be determined by a mineralogical analysis. Polish sections have to be prepared and interpreted by using of a microscope. Figure 1 and figure 2 are showing polish sections of a platinum-nickel ore from Petchenga Nickel at Zapolyarni Mine in Russia. The head grades for rich ore are for copper between 0.05 – 0.15%, for nickel between 3 – 7% and for platinum group minerals approx. 0.15 oz/t. With an efficient flotation technology it can be upgraded to 20 oz/t."

Jan 1, 2009

By Steve Kral

The mining industry has waited a long time for the resurgence in commodity prices and demand for its products that it is now experiencing. Base and precious metals prices have reached levels not seen before. Coal prices have also shot up. And there are encouraging signs in the uranium market. China’s nearly out-of-control economic growth is said to be the leading driver for much of this resurgence. But demand for energy, metals and building materials in the United States and elsewhere are also major factors. The result is that expansions and new mines for nearly every commodity are in the works.

Jan 1, 2005

By D. Xie

An in situ gravimetric technique based on wetting and capillary action principles has been used to investigate the wetting and penetration of synthesized alumina samples and commercial magnesia spinel refractories by CaO-SiO2-Al2O3-Fe2O3slags. Synthetic slags of 40CaO-40SiO2-20Al2O3 (in weight per cent) with 0 to 9 weight per cent Fe2O3were used and the experiments were conducted at temperatures 1370 to 1470ºC under argon. The contact time between the sample and the slag was 30 minutes. The results show that the wetting and penetration are enhanced by the iron oxide addition in the slags. Addition of Fe2O3from 0 to 9 weight per cent resulted in a significant increase in the slag penetration into the magnesia spinel refractory by a factor of about 7 and a moderate increase in the synthesized alumina by about 60 per cent. The addition of Fe2O3enhanced the wetting (??cos?, where ? is the surface tension of the slag and the contact angle between the slag and the refractory) by 5 to 18 per cent. An increase in temperature from 1370ºC to 1470ºC resulted in a significant increase in the penetration of a 6 weight per cent Fe2O3slag in the alumina and magnesia samples by a factor of4 to 5 and a decrease in wetting by approximately 30 per cent. Keywords: refractories, slag penetration, wetting.

Jan 1, 2004

By Rao P. K, Sahoo P. K

The main constituents of ferromanganese slags are silicates of Mn, Ca and AI. Factors affecting the recovery of manganese from a low manganese content ferromanganese slag (about 16 per cent MnO) during acid leaching were studied. These included time, temperature, agitation, sulphuric acid addition, solid:liquid ratio and particle size. Agitation rates greater than 300 rev/min. leaching periods greater than 30 min and temperatures above ambient were found to have no effect on Mn recovery. Dissolution of Mn was found to be highly dependent on the amount of acid added.About 90 per cent of the Mn was recovered when 5·5 times the stoichiometric amount of acid was used. About 28 per cent of the Mn was recovered when the stoichiometric quantity of acid (with respect to Mn alone) was used. However, the recovery increased to about 75 per cent when the total stoichiometric requirement of acid with respect to Ca, Al, Mg and Fe as well as Mn was used for leaching. The extent of Mn dissolution also depended on the particle size of the slag. The percentage of Mn recovery (using 5·5 times the stoichiometric amount of acid) increased from about 60 per cent to about 92 per cent when particle size decreased from -36 +52 to -150 +200 mesh (B.S.S.). When the results of this study were compared with those in a previous study involv,ing the leaching of a high manganese content slag (containing about 40 per cent MnO) results were similar except that there was a gr-eater consumption of acid in the present case (i.e. low manganese content slag).

Jan 1, 1979

By D. Denton, M. Stickney, R. Langston

The National Institute for Occupational Safety and Health and the Stillwater Mining Company worked cooperatively with the Montana Bureau of Mines and Geology to develop a system that would collect seismic data at the Stillwater and East Boulder mines. The purpose was to obtain baseline information on the magnitude and location of mining-induced seismicity to determine if the mines needed multi-channel in-mine monitoring systems. Seismic data recorded at field sites near the mines are being telemetered via FM radio through a series of repeaters to a central recording site where the seismic signals are digitized using an Earthworm data acquisition system. The Earthworm system performs several data analysis tasks in near-real time and places raw seismic data, preliminary hypocenter locations, and magnitudes on a Website within 5 min of a seismic event. Such rapid access to seismic data allows personnel at the Stillwater Mine, Spokane Research Laboratory, and Earthquake Studies Office to evaluate seismic events quickly and respond in ways that may improve the safety of mine personnel underground. Installation of the system also broadened earthquake coverage to south-central Montana, a region previously not covered by the seismograph network.

By G Dunstan

The Ridgeway gold mine has been an enigma of the international underground hard rock community for nearly 20 years. It nearly didn’t eventuate as it was more than 500 m below a farmer’s paddock in Central New South Wales when the exploration team, looking for open pit deposits, got a sniff on its last attempt and then drilled the high-grade discovery hole. It took separate studies to find an economic mining approach. Newcrest, then a mid-tier mining company, took the venture that set it on a path of growth and built what was to become the backbone of the company for the next 15 years.The initial mining method was sublevel caving (SLC) for the upper 300 m of the orebody. The nameplate production rate for the SLC was 4 Mt/a, which was reached in June 2002 shortly after the commissioning of the materials handling system. The ultimate production rate was subsequently lifted to around 6 Mt/a through a series of innovative and efficiency initiatives. In June 2007, approval was granted for the development of a block cave (BC) operation to extract the ore reserve situated immediately below the existing SLC operations, Ridgeway Deeps. The BC was designed at approximately 6 Mt/a to match the concentrator and a systematic improvement process through the entire underground system again saw delivery rates consistently around 10 Mt/a.In line with the production rate increases, Newcrest was also committed to advancing caving knowledge through a number of targeted research and development experiments and new processes. These were primarily related to improving cave ore recovery through systematic draw marker trials, cave propagation through preconditioning techniques with associated monitoring systems. New technologies were also developed to improve the safety and efficiency of the mine through data collection, cave establishment techniques, production dispatching and autonomous loading.CITATION:Dunstan, G, 2016. The truth is stranger than fiction – the story of Ridgeway gold mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 19–30 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By John A. Folinsbee

Placer Dome Canada owns and operates the Campbell mine and mill at Balmertown, in the north western corner of Ontario. The mine operates at 1.3 kt/d (1,500 stpd). It produced more than 9.3 t/a (300,000 oz/year) of gold during the last three years. Changes to the gravity concentration circuit have resulted in a 10% to 15% increase in gravity recovery. The mill head grade at the Campbell Mill is relatively high, averaging 18.5 g/t (0.54 oz/st) over the total reserve tonnage. During the past several years, the head grade was averaging close to 20 g/t (0.6 oz/st). Before 1994, gravity concentration was achieved by using a combination of conventional mineral jigs and tables. Jig concentrates were upgraded on shaking tables to produce a concentrate, which was refined to bullion. In May 1994, management decided to buy two Knelson CD 760-mm (30-in.) concentrators. The objective was to replace the existing jigs and increase gravity gold recovery by up to 15%. Gravity recovery with jigs averaged between 30% to 35%. Gravity recovery was anticipated to increase to about 50% with the Knelsons.

Jan 1, 1997

By R. P. Gardner

Results of work on the development of a phenomenological model for the continuous flotation process using short-lived radioactive tracer techniques for the determination of model parameters is reported. A model that incorporates a flotation first-order rate constant and a residence time distribution based on the cross flow finite state (CFFS) model has been derived and investigated. The short-lived radioactive tracer techniques necessary to extract the model parameters have been developed as have the necessary nonlinear search methods. The conditions under which all the model parameters can be extracted from a single radiotracer experiment are detailed and illustrated. A microcomputer-based unique data logging system has been designed, assembled, and implemented for collecting the necessary transient radiotracer data. Results are reported for a continuous laboratory flotation system for the two systems mica ore and coal.

Jan 1, 1985