Search Documents

By Reda M. Bakeer

"Measurements obtained during load testing of two steel H-piles driven at a site in Northeastern Mississippi are discussed. The general site conditions, equipment used, testing procedures and results of the pile load tests are presented. Both piles were tested in compression and one of the piles was subsequently tested in tension. The piles were instrumented with strain gauges and extensometers to measure the mobilized soil resistance and pile movement. Three different “zero strain” conditions were used to determine the mobilized soil resistance and residual loads due to driving or a load cycle. It was concluded that the effect of residual loads on driven piles could be significant. Driving residual loads influenced the magnitude and distribution of the load transfer curves more than those due to a load cycle. Results of the tension test were impacted by the residual loads from the previous compression test performed on the same pile.INTRODUCTIONSeveral factors affect the performance of a deep foundation system including the subsoil conditions, loading settings, pile type and installation method. Residual stresses develop in piles particularly due to pile driving, but they are typically not accounted for in the analysis (Fellenius 2002). Siegel and McGillivray (2009) presented an assessment of residual loads measured during load testing of instrumented auger-cast-in-place (ACIP) piles. The magnitude and distribution of residual stresses along the pile shaft and toe depend on the pile installation method, previous load cycles and time effects. Poulos (1987) reported that residual load due to driving at the pile toe is independent of pile driving equipment and may significantly affect the results of a pile load test. Hunter and Davisson (1969) reported results of pile load tests performed in compression on fully instrumented piles driven in cohesionless soils along with a discussion of the effects of residual loads. Tension loads of about 445 kN (100 kips) were measured at the pile toe after driving. Unloading residual compression load at the toe was detected as “apparent” tension since the instrumentation was zeroed prior to the test. The researchers suggested a graphical approach to obtain the “corrected” load distribution curves considering that residual load will dissipate following the tension test. Holloway et al. (1975) conducted a study on the effect of residual stresses due to pile driving and developed a computer software that accounts for residual loads. Briaud and Tucker (1984) suggested a method to account for residual loads based on the results of 33 pile load tests performed in mostly cohesionless soils."

Jan 1, 2017

By David Yang

Commercially available flotation technologies for recovery of mineral fines have remained essentially unchanged for several decades. Recent studies have focused simply on improving mechanical and open column cells. Such studies have explored different control strategies and have aimed to improve reagent selectivity, fine air bubble generation and particle-air contact. However, no study has questioned whether current techniques are the most efficient technology for recovering mineral fines. Given that both mechanical and open column cells have a widely accepted carrying capacity limitation, the lack of extensive research into an alternative technology is surprising. Most recently, open column flotation has become an entrenched technology, and it is undermining the efficient recovery of mineral fines worldwide. An alternative exists. Packed column flotation overcomes the above-stated problems as the technology surpasses the carrying capacity limitation of current means by several-fold and almost always achieves the best performance in many comparative pilot tests and full-scale plant operations. Filling a column with packing plates creates a network of sloped walls capable of supporting a froth bed many times deeper than conventional machines. Having froth up to 75 percent of the total column volume tolerates all feed changes encountered in the plant environment and permits maximum flexibility in concentrate quality control. Furthermore, its scale-up is straightforward by increasing column volume or the number of interconnected small cells. As the air breaks upon rising and is distributed horizontally through packing plates, the air spargers can be replaced with a simple blower, resulting in considerable savings in operation and maintenance costs. Packed flotation technology provides a break-through solution for the separation of fine and ultra-fine minerals. Its simplicity, superior performance, and low cost structure make it an appealing alternative to current technologies and allow greater flexibility in downstream processing. Future industrial applications include a wide variety of metallic and non-metallic ores. This paper focuses on some recent scale-up campaigns for nickel and copper sulphide flotation applications compared directly to conventional equipment.

Jan 1, 2014

The preeipitation of dissolved lead from a strong brine by metallic iron is a chemically controlled, first order reaction. The precipitation rate is sensitive to changes in chloride concentration and temperature. The precipitation of dissolved silver is a diffusion controlled, first order reaction. The precipitation rate is insensitive to changes in chloride concentration and temperature.INTRODUCTIONLead and silver sulphates can be extracted from electrolytic zinc plant tailings, or residues, by leaching with strong brine solutions, the lead and silver going into solution as complex chlorides. One of the methods which can then be used to recover the dissolved lead and silver is to precipitate them with metallic iron. The deposition reactions which take place are of the type Pb++ Fe - Fe++ Pb............ (a)To fit such a method of precipitation successfully into a practical flowsheet it is necessary to have some knowledge of the kinetics of the various reactions, Le. to know how the precipitation rates vary with temperature, brine and metal concentrations, and so on. Reaction rates are also needed to design suitable precipitation vessels. However, when examining the possibility of using a brine leaching process to extract the lead and silver from the residue produced at the Risdon plant of the Electrolytic Zinc Co. of Australasia, it was found that, although the use of metallic iron to recover lead and silver from the pregnant brine had been reported by Ralston (1924) and by TrumbulI, Hardiek and Lawford (1948), very little was known about the precipitation reactions. Consequently a laboratory investigation was undertaken, and this paper covers those aspects considered to be...

Jan 1, 1961

By W. P. Arnott

This paper presents real time photoacoustic measurements of diesel-soot black-carbon (BC or EC) and Dusttrak nephelometer total carbon (TC) concentrations in a Nevada gold mine. Comparisons with time-integrated filter-based measurements of EC and TC accomplished using the NIOSH 5040 method were found to be 50% smaller than the integrated real time measurements. This work was initiated primarily as a demonstration project for the usefulness of photoacoustic instruments in measuring BC in the mine environment. Real time black carbon measurements are very useful for determining miner exposure, for providing feedback in mine ventilation systems, and for quantifying machine specific emission rates to understand the operating conditions for specific machines that produce greatest black carbon concentrations. This paper reports real time measurements of DPM from a loaded and empty hauler as it is operated in a drift with a 12% grade. The photoacoustic instruments were demonstrated to be satisfactory for BC measurements in the mine environment.

Jan 1, 2009

By Tom Meikle

Long tendon support systems provide several challenges when used in-cycle as part of the secondary or primary support cycle. A two-component pumpable resin, Carbothix, has been in development for use with self-drilling rock bolts, but many of the attributes of this new resin system make it ideal for grouting long tendon support systems. While neat Portland cement grouts or polyester resin capsules have been used with long tendon support systems for many years, two-component pumpable resin systems overcome many of the shortcomings in these systems. The two-component systems dramatically improve the set-time to enable mining face advance with fewer delays, enable longer pumping distances, improve quality control, and enhance load transfer mechanisms. This paper describes the key benefits associated with a new pumpable resin and details the Australian Department of Mines and Petroleum department atmospheric testing results and cable load testing completed by Minova personnel to date. It also details the results of the Australian mine site trials and the introduction of these systems into production use.

Jan 1, 2012

By J. J. Forbes

First - aid training is an essential part of safety programs in the mining industry , but it is only a means to an end ; first -aid training will not eliminate accidents , but unquestionably it is of considerable value in any accident prevention program . Numerous features should be incorporated in any efficient , well - developed safety plan ; in addition to first -aid training safety work , to be reasonably effective , should include the establishment and maintenance of a safety organization , safety competitions between mines or sections of mines , safety- inspection committees , accident - investigation committees , safety meetings of mine officials , safety bulletins and posters , employees ' safety publications , Holmes Safety Chapters (which provide for monthly safety meetings of all employees ) , and numerous other activities looking to safe operation of mine or plant . These features are supplementary to the fundamentals of safety-- adequate and effective supervision and discipline . Years of experience , however , have demonstrated that first - aid training is a good accident -prevention auxiliary and should be made an integral part of every company's safety program . Many safety-organization plans have failed because they have been based upon the assumption that the supervisory force should be given full authority and responsibility for achieving safety and eliminating accidents and that the workers , who are most vitally concerned , are nonessential . First -aid training causes the employees to feel that they have a personal and full participation in the safety program and is now available so readily that no individual or organization has any valid excuse for not having it . Early investigations made with a view to bettering health and safety conditions among the employees in the mineral industries demonstrated the need of prompt care of injured employees because , under the difficulties inherent in the occupation , seemingly unimportant wounds , when not treated promptly, became infected and caused permanent disability and even death . Many seriously injured persons , brought out of mines and plants by fellow workers who were ignorant of the approved methods of giving first aid or of safe means of transportation

Aug 1, 1934

By Mike Robotham

When RFQ?s are received they often contain detailed technical specifications which suggest a departure from the suppliers own customary approach to the design. Both client and end user are quite rightly influenced by their own experiences. The question is who is right, the client and his consultant, the supplier or perhaps a combination of these. This paper looks at some of the fundamental variances that often occur in the approach to the mechanical design of drum hoists, based on our experiences of recent years. Director of Engineering, Mike Robotham is a chartered engineer and has been with DavyMarkham for over 30 years. Having completed a craft apprenticeship he later joined the engineering department as a junior engineer. He has a wealth of experience of working on medium to large engineering projects in the field of mechanical, electrical and hydraulic equipment

May 1, 2011

Multilevel-multiseam hardcoal mines on the European continent usually consist of a huge network of underground openings, sometimes more than 200 km long in total, with some longwalls operating down to a depth of 1,500 m. While operating several longwalls simultaneously, these mines are making use of a number of stationary and mobile measurement- and analysis units in their main ventilation passes combined with atmospheric measurements on the surface. This paper provides an overview over the systems and technology used and describes the typical set-up of a measuring net. To detect and monitor underground fires through fire gases measurement and -analysis, a mobile underground testing laboratory collects data locally in the area of the fire. These laboratories have proven to be extremely useful not only during the actual fire fighting but also for the long-term gas measurements in critical mine areas. They have repeatedly detected starting fires and have thus given the mine the opportunity to react early and to avoid larger damage. Therefore several mobile laboratory units have now been installed for long-term testing in a number of German mines and similar units are being used in the Czech Republic and Poland.

Jan 1, 2012

In general, the metallurgical industry has so far been slower than the chemical industry to adopt ion exchange materials for industrial processes. The atomic energy industry presents a marked exception to this general situation, and the literature shows a rapidly increasing use of ion exchange techniques for the recovery of atomic energy metals on scales ranging from the ultra micro up to that of the largest mining operations. In many cases, the processes used would be equally applicable to more common metals and it is hoped that this review will be of interest to metallurgists outside the specialised atomic energy field. The review is intended to describe developments of ion exchange processes made during the last three years. Earlier studies have been summarised by Kunin and Preuss (1956) and Roland (1957). In order to restrict the number of references discussed, purely analytical procedures have been omitted and only those processes which have been conducted on a reasonably large scale or which, from their nature, areclearly capable of being upscaled, have been considered. The paper is divided into five main sections concerning respectively:Water treatment and effluent disposal.Metal recovery and purification.New ion exchange materials.New ion exchange equipment.Membrane cells.WATER TREATMENT AND EFFLUENT DISPOSALA high proportion of atomic reactors, and particularly those of American design, are cooled by water which is...

Jan 1, 1961

By B. Arlyuk

On the basis of research of relations among the market participants the analytical model has been created which connects the price of industrial good at stock exchange with volume of sales and the stock of the sellers and buyers, Also a model was developed for assessment of these parameters of the market status by the actually fixed stock exchange and general market indicators. The composition of these models made it possible to create reliable system of short-term price forecasting for commodities or base metals up to one quarter ahead. Imperfectability of creation a model for reliable price forecasting by purely statistic methods (by the "black box" principle) was shown. A model of price behavior qualitative forecasting till one quarter ahead has been developed, which determines the probability of reaching in future of the given level as well as of the price maximums and minimums, Optimal values of threshold probability were determined for forecasting the future price maximums and minimums securing the maximum profit from the forecasting system application for commercial activity. The developed system of forecasting was identified for primary aluminium at the period of 1990-2003. The system was tested daily during 20 months period for speculations on 3M primary aluminium forwards at London Metal Exchange with high commercial result.

Jan 1, 2004

By Ning Wang, Tengfei Guo, Wanyan Li, Hanjie Wen, Hannian Gu, Zehai Li

Bauxite residue (red mud) is an alkaline waste derived from the industrial process for extraction of alumina from bauxite ore. Some bauxite residues contain considerable concentrations of critical metals, for example, rare earth elements. Lithium in red mud was also reported as a potential resource. In the current study, a Li-rich red mud was leached using acetic acid to investigate the leaching behavior of lithium followed by neutralizing with hydrochloric or oxalic acid. By neutralizing red mud using diluted hydrochloric acid (0.01 mol/L), 58.04–60.27% of lithium was leached using 25% acetic acid at 95 °C for 60 min. In the meantime, more than 95% of sodium and 85% of calcium were also dissolved in the leachate solution. While oxalic acid (0.5 mol/L) was used to neutralize red mud prior to acetic acid leaching, lithium performed lower leaching efficiencies (42.41–46.88%) in comparison of using of hydrochloric acid–neutralized red mud. Nevertheless, these leaching efficiencies of lithium were close to that of calcium and much higher than those of sodium under the condition. In this study, 25% (v/v) of acetic acid, at 85 °C for 60 min, was demonstrated as optimum conditions for lithium extraction from oxalic acid–neutralized red mud using acetic acid. The results would be useful and of interest for lithium recovery and purification from red mud.

By D. Harrington

Coal mines and mining-, as well as metal and nonmetallic mines and min¬ing, are not inherently unsafe, although mining people think they are and would like to have everyone else think so. It is now being demonstrated that mines can be operated with essentially as much safety as any other major industrial enterprise; but most mining people, including workers as well as officials, have been slow to realize or admit this. In the past, and with most people even at present, the idea has prevailed that it is utterly impossible to operate a mine without accidents. Although, as in all other kinds of industrial activity, it is true that some injury is likely on occasion to occur to some workers and an extraordinary accident may occur to one or more persons under exceptional conditions, mines can be operated with few if any accidents if a reasonable amount of the right kind of precautionary effort is exerted and kept in effect.

Jan 1, 1934

The mineralogy and microstructure of mattes from the nickel flash smelter at Kalgoorlie, Western Australia, have been studied. The flash furnace matte consisted mainly of an intimate mixture of pentlandite and heazlewoodite with some nickel metal. The electric furnace matte was mainly an iron-nickel alloy with subsidiary pentlandite while the converter matte consisted mainly of heazlewoodite with crystals of nickel metal.

Jan 1, 1977

By Alvaro Veizaga, Samuel Cuellar

In recent years, Industry 4.0 has generated a change in the way companies in various industrial sectors design, produce and deliver products and services, and is focused on the interconnection of systems, the advanced access and management of large amounts of data in real time, and the implementation of emerging technologies such as the Internet of Things (IoT). Artificial intelligence (AI), machine learning (ML), digital twins (DT), robotics, virtual and augmented reality (VR/AR), among others [1]. DTs are accurate and dynamic virtual models that replicate physical systems, where it is possible to simulate and optimize operations before implementing real-world changes [3]. These features make it possible to reduce investment costs, minimize risks and improve strategic decision-making. These benefits are of utmost importance for tailings storage facilities (TSF), since they are facilities aimed at the safe storage of tailings and with the constant need for growth [4]. This paper evaluates the applicability of a DT in a TSF from a conceptual perspective, providing the advantages of its implementation, but also the barriers identified in the industry based on the authors’ experience.

Feb 1, 2025

By R. Hammen, J. Lifton

"The purification of rare earth elements (REE) at mining operations is traditionally accomplished by multiple chemical phase-transfer processes including precipitation, solvent extraction, and ion exchange. We describe REE purification results with Solid Phase Extraction (SPE) columns that were developed to improve the speed and economy of REE purification. The SPE columns have the properties of enhanced equilibration kinetics, so that residence time of a few seconds will accomplish selective chemical transfers from solution phase to solid phase. We describe the separation of REE’s as a class from leach solutions and the further purification of REE salts. INTRODUCTIONHistorically the rare earths were first chemically separated from each other and purified by fractional crystallization. This slow, cumbersome, and laborious process was not suited to commercial production. Solvent Exchange (SX) technology was applied to the problem of separating and purifying the rare earth elements when it was determined in the late 1960s that there might be commercial uses for them individually. At the same time the very slow and expensive technique of ion exchange was applied either for ultra-purification of the desired “light” rare earths, or for the recovery and purification of the tiny amounts of higher atomic numbered, “heavy,” rare earths. Solvent Exchange (SX) has today become the standard for separating the rare earths across their atomic number spectrum. Whereas the separation of the light rare earths commercially may take 30 “cascades’ in a modern Chinese plant, the total separation of all of them from each other may take up to 80 such “cascades,” and is only even “practical’ with preconcentrated feed stocks, such as those produced in China by heap-leaching techniques performed in situ on very low grade radio-nuclide free ionic absorption clays.. Ultra-pure materials of all types are produced today by ion-exchange processing of ionic species already separated by solvent exchange.Hard rock deposits and refractory residues of tin mining and residues from uranium mining have been identified outside of China with very high ratios of dysprosium and other heavy rare earths to the majority lighter ones. Several issues face those who wish to process these materials so as to separate the heavy rare earths commercially:"

Jan 1, 2012

By D. C. Panigrahi

Extensive field studies have been carried out to investigate the pillar fire problems in one coal mine in India. A Thermal IR gun and a Thermovision camera have been employed for thermal scanning to assess the state of heating in selected pillars. Special sampling set-ups have been designed to collect gas samples from the holes drilled into the selected pillars and the multigas detector is used to analyse the composition of samples in situ. In order to predict the spontaneous heating in coal pillars, different gas ratios have been calculated and it has been observed that some of the established gas ratios, viz. Graham?s ratio, Young?s ratio etc. have resulted in negative values in samples containing high amounts of methane. The modified gas ratios have been proposed which will be useful for predicting the pillar fires. These ratios may also be used for assessing the condition of fires in sealed-off areas.

Jan 1, 2004

By V N. Rudashevsky, F Melcher, J Lodziak, D Klosa, N S. Rudashevsky, M Sitnikova, L Gast

A combination of novel and æclassicÆ methods, namely electric pulse disaggregation (EPD), hydroseparation (HS), preparation of monolayer polished sections, and mineral liberation analysis (MLA) was employed to study ores from platinum pipes (Bushveld Complex, South Africa), pristine PGE mineralisation of the Main Sulfide Zone (Great Dyke, Zimbabwe), as well as ancient and modern gold/PGM placer deposits. It is shown here that the EPD technique liberates mineral grains of interest without any visible destruction allowing the study and analysis of individual rock-forming and ore minerals, in our case especially platinum-group minerals. The HS method is an effective tool in concentrating heavy minerals by factors up to 10 000 fold. As near-total recovery of grains >10 ¦m is achieved, the nugget effect can be overcome also in case of limited availability of samples (drill core, museum specimens). The MLA technique is a fast tool to detect and characterise mineral phases in ores and ore processing products. Many mineralogical parameters of individual grains and mineral assemblages can be deducted and documented. The results show that the techniques employed, either on their own or in combination, provide a wide range of additional information especially on platinum ores which is beneficial to both the researcher and the metallurgist.

Jan 1, 2008

By R. W. Culbertson

During the 1920's, approximately 11,000 small gasifiers were in operation in the United States. They converted about 15 million tons of coal per year into low Btu gas. In some cases, hot raw gas was used for applications such as firing open hearth furnaces or brick kilns. In other cases the gases produced in the gasifiers were cooled, cleaned and desulfurized for various utility and industrial purposes. The steel industry was by far the largest user. The most important fact was that the conversion of coal to a usable fuel gas was demonstrated to be commercial. During the late 1940's and early 1950's, this form of energy was largely replaced by natural gas as the pipeline net work was expanded. Producer gas was no longer economically competitive. Over the past twenty-five (25) years, government controls on the interstate price of natural gas have maintained this situation. At present only three commercial small coal gasifier plants are still in operation in the United States. These facilities are operated by the Glen-Gery Corporation which is located in eastern Pennsylvania; the National Lime and Stone Company which is located at Carey Ohio; and Holston Defense Corporation which is located at Kingsport, Tennessee. There are, however, numerous operating gasifiers in other parts of the world. Recent events indicate that this situation is changing. The quantity of domestic natural gas available to the interstate market has been declining at the same time that demand for all forms of energy has been increasing. The current potential market for gas with a heating value ranging from 100 to 500 Btu per cubic feet has been estimated at sixteen (16) quads (16 x 1015 Btu) per year. This is expected to grow to twenty (20) quads by the year 2000.

Jan 1, 1978

By M. Didyk

In this report, the application of the PHU/MVS program is demonstrated through the use of a simple but realistic mine ventilation program. The report details, the problem description, the input data required and the various output features of the simulator. The PSU/MVS program is written in Fortran IV for use with IBM 370/168 computers. A version of the program that can be used in CDC computers is also available. A ventilation network consisting of 531 branches, 300 nodes and 5 fans took 48 seconds for solution on The Pennsylvania State University's IBM 370/168 computer. Appendix I of this report is the User?s Manual for the program. Appendices II and III contain the input data listing, and selected output listing for; the application. Appendix IV provides tables for leakage, friction factors and shape factors.

Jan 1, 1977

By R. W. Drier

THE conductivity of copper wire is of prime importance to the electrical industry and consequently to the copper refiner and wire manufacturer. Annealed copper wire has a higher conductivity than hard-drawn wire, but, on the other hand, its tensile strength is lower. In an attempt to explain the reasons for these changes in property or at least to study the conditions existing in these two types of copper wire, the experiments described here were carried on in the Department of Metallurgy of the Michigan College of Mining and Technology. This is only a partial and preliminary report on some of the work done to date on a research program of which the object is an intensive study of copper. It is offered with the hope that, though it is not an exposition of the most rigorous of conclusions, the general trend of inferences which may be drawn will be of value and interest.

Jan 1, 1929