Search Documents

The Mahakipawa gold deposit is located 21 km northwest of Blenheim. It became the site of a small hardrock gold rush in 1889 following nearby alluvial gold discoveries in 1888. The study investigates the geology of the area of hard rock mining in the vicinity between Cullens and Waikakaho Creeks. The Marlborough Schist which hosts the gold depos, it consists of polydeformed greenschist facies quartzofeldspathic psammitic, pelitic and volcanigenic schist.

Jan 1, 1993

? CONSTRUCTION AND MINING COSTS ARE HIGH IN THE ARCTIC ? VERTICAL KIMBERLITE PIPES WITH HIGH STRIP RATIOS ? SITE SPECIFIC GEOMETRIC CONSTRAINTS ? OPEN PIT FOLLOWED BY UNDERGROUND MINING ? HIGH KIMBERLITE UNIT COSTS TRACK INSTALLED ON PIT WALL ? INTENDED TO REPLACE MAIN HAUL RAMP ? 5 MIN HOIST CYCLE TIME ? KEY ADVANTAGES - REDUCED CYCLE AND STRIPPING RATIO ? TECHNOLOGY EXISTS IN OTHER APPLICATIONS

May 1, 2003

By Charles G. Maier

"INTRODUCTION The use of thermodynamic calculations to answer practical problems in metallurgy, especially those that are relatively difficult to test experimentally, is rapidly becoming a conventional method of procedure. Nevertheless, these methods cannot he applied effectively until the fundamental thermodynamic constants used for them have become available either by direct experiment or by recalculation of data already existing in more or less undigested form.In an attempt to collect such data far the compounds of lead and the antimony group the incentive has been to make a preliminary survey that will disclose the gaps or questionable phases of available information and to collect data that may be used to answer certain rather practical problems presented by operating metallurgists.This report comprises three sections; the first gives the basis of selection of the constants which may now be given or estimated, and the later sections discuss the application of the figures obtained to two of the more interesting problems.The reader will discover that many of the quantities involve critical study of a number of more or less discordant observations. Although certain data could be rejected on the basis of thermodynamic comparisons, it must not be overlooked that many of the figures are the results of rational estimates rather than exact experiment. The use of thermodynamic methods to control and partly authenticate such estimates is one of its most valuable characteristics for the practising metallurgist or chemist, who cannot check by direct experiment each property of the materials which he converts to usable form.Nevertheless, while it is definitely possible in certain instances that the final figure selected for the heat or free energy of a process or substance may be in error by as much as a few hundred to a few thousand calories per formula weight, questionable figures are usually revealed by the thermodynamic calculations made. When quantities of such degree of accuracy are, and they often must be, used for estimating an unknown reaction, the result often gives no more than the order of magnitude of the desired quantities. Yet even in these extreme cases the answer is far more reliable and valuable than an unordered guess or a conclusion based on incorrect data."

Dec 1, 1934

By K. Loutet, A. Guenkel, K. Nikolaisen

"The INCO SO2/air process was patented by INCO in 1985. Well over 80 mining operations worldwide are using this process to oxidize cyanides to cyanates in the tailings from gold, silver and copper mining operations. The sulphur dioxide (SO2) for this process can be supplied either as liquid SO2, SO2 gas or as a sulphite-based salt. The majority of SO2/air operations have used sulphite-based salts as the ‘SO2’ equivalent probably due to low capital cost. Liquid SO2 has also been used frequently, but due to concerns with safety and availability, this option is often not preferred. The solid salt sodium meta-bisulphite (SMBS) is commonly employed, but its cost is an order of magnitude higher than that of sulphur. Due to the high cost of SMBS, the increased capital cost for a sulphur-burning SO2 gas plant (green field or retrofit) usually has a pay-back of less than three years. In addition, a SO2 gas plant offers potential for significant heat recovery from the sulphur burning process. In terms of safety, the SO2 gas plant only requires the storage of relatively benign sulphur and the site inventory of SO2 will be limited to the plant gas volume. Therefore, a SO2 gas plant will not trigger the Canadian Environmental Protection Act (CEPA) E2 Regulations or the US Clean Air Act Section 112(r) accident prevention regulations, as may be the case for liquid SO2.Most existing mining operations using ‘SO2’ are gold operations, but in recent years there has been an increased interest in larger sulphur dioxide gas plants for hydrometallurgical facilities that employ leaching of cobalt/manganese minerals or precipitation of manganese/iron (e.g. Tenke Fungurume and El Boleo).This paper focuses on the production of sulphur dioxide gas generated on site and on demand for the use in hydrometallurgical processes. The capital and operational costs of a SO2 gas plant is compared to conventional process alternatives using sulphite-based salts or liquid SO2."

Jan 1, 2016

By N. Merriam

This report describes Koppelman's work to develop the K-Fuel® Series C Process used to dry and stabilize Powder River Basin coal. It also contains summaries of the results of bench-scale and pilot plant tests conducted to prove the Series C Process. The process is being used by the KFx-Thermo Ecotek partnership for a 500,000 ton per year commercial plant that has been constructed near Gillette, Wyoming. The plant is presently undergoing shakedown.

Feb 24, 1997

By Edmonds W, Jeffcoat R

The completion of the first two open hearth furnaces in the new No. 2 open hearth plant at Port Kembla will increase Australian production of steel by 350,000 tons of ingots per annum.The paper gives an outline of the essential features of open hearth design and auxiliary equipment required to operate the two modern open hearth furnaces at present being installed.INTRODUCTIONThe increasing demand for steel required by Australian secondary industries led to the decision to construct and operate No. 2 open hearth plant at Port Kembla. Two basic open hearth furnaces of the most modern design are under construction and it is anticipated that these units will be commissi.oned in September 1956. Australian steel capacity will thereby be increased by approximately 350,000 tons of ingots per annum.PLANT LAY-OUT AND CONSTRUCTIONIn the design and lay-out of this plant the emphasis has been on efficient material handling with simplicity of design and operation. Overseas methods were studied and these studies, together with experience gained at Newcastle and Port Kembla open hearth shops, enabled this plant to be built to a standard which compares favourably with any other in the industry.Initially two furnaces, each of 2,75 tons capacity, have been built, but provision has been made in. the design and lay-out to enable expansion to six furnaces.The location of the new plant in relation to the existing units will be noted in Fig. 5. It is one of the first units to be built in an area which will dovetail into a pattern for...

Jan 1, 1957

Electrochemical measurements are presented on electro-deoxidation of silica in molten calcium chloride at 900°C, with porous silica pellets as starting material. Measurements during pre-electrolysis (to remove water from the melt) showed electrochemical noise, which is consistent with the evolution of hydrogen. Throughout, the dominant anodic reaction appears to be CO2formation, based on the observed potential at the anode, and measured anode wear. Because of the presence of dissolved CaO in the melt, some of the CO2 candissolve in the melt; the resulting calcium carbonate formation was confirmed by electrolyte analysis after reduction runs. Reduction of dissolved CO2 at the cathode is likely to contribute to the background current during the reduction process. For the electrode and cell configuration used here, most of the over potential arises from polarization of the anode, and ohmic potential drop in the electrolyte.

Jan 1, 2006

By R. P. H. Willis

For technology transfer to be successful a process, from research to full scale application, has to be followed. This paper describes such a process and how it is applied in practice. Some of the ?do?s? and ?don?ts? are highlighted. Recommendations are made on how to communicate existing knowledge and to ensure that a framework exists to effectively plan future projects with final technology transfer objectives firmly in place. The Impact Ripper System is used as a case study to illustrate lessons learned. Key words: Technology transfer, implementation

Jan 1, 2002

By James K. Kindig

Hazen Research, Inc., has developed a new process for removing pyritic sulfur and ash from coal. Feed coal is contacted with iron carbonyl vapors, Fe(CO)5, at 190°C which puts a thin skin of magnetic material on the pyrite and ash, but does not affect the coal. Thus, low intensity magnetic separators yield a nonmagnetic coal, low in sulfur and ash, and a magnetic refuse, high in sulfur and ash. Results are given for clean coal produced by this method. A comparison is made between results of the magnetic process and the U. S. Bureau of Mines two-stage flotation process cleaning identical samples of Pittsburgh Coal. Capital and operating costs of the two cleaning methods are discussed.

Jan 1, 1976

By Larry A. Morris

The environmental impacts of industrial activities have become very serious concerns of the public over the past few decades. Not surprisingly, governments have responded with legislation and regulations to force industry to operate in a more environmentally responsible manner and, more recently, have prompted industry to initiate voluntary measures in response to specific environmental issues. The concept of Product Stewardship has evolved as a system or vehicle for the industrial sector to demonstrate an active concern about the environmental impact of their products, services and processes.

Jan 1, 1996

By G. E. Blight

Wind erosion can be a major cause of the loss and dispersion of tailings material from a tailings dam into its surrounding environment. Such dust dispersion can be a serious nuisance, as well as a health hazard to inhabitants in nearby settlements, and can also damage the health of animals, degrade crops, making them less marketable, and cause soil and water pollution. The problem of wind erosion can affect tailings dams in all types of climate, but becomes worse as climatic aridity increases. Because clouds of dust are often observed billowing across the top surfaces of tailings dams in dry windy weather, there is a common misconception that the dust arises from wind erosion of the top surface. As a result, much effort and money is vainly spent on treating the tops of tailings dams to prevent dust generation, whereas the slopes of the dams are the true major dust source. This paper briefly reviews what is known of erosion of tailings dams and then proceeds to describe the mechanics of wind erosion in general, and how it affects tailings dams in particular. Finally, recommendations are made for mitigating wind erosion of tailings dams and the resulting blowing dust.

Jan 1, 2007

Project cost control procedures and computer systems have enjoyed a successful and simple relationship over the past decade, thanks primarily to the proliferation of portable computers or PC's. Prior to the introduction of this technology, project control was largely a manual and somewhat onerous task of historical data compilations, with little time available for dynamic forecasting, staged planning, or pre-emptive cost control. Automated systems developed during this era were resident on "Heavy Iron" or mainframe computers and were expensive to maintain and operate. Use of these early systems was limited to large engineering, construction, and industrial concerns with the economies of scale and funding required for their successful application. Systems were either designed for critical path analysis or task scheduling, but rarely integrated with the other, much less cost control.

Jan 1, 1990

By D J. Brake

The importance of mine ventilation to health and safety in both coal and metalliferous mines has been long recognised. The primary and secondary ventilation systems in most metalliferous mines incur 50 per cent or more of the total mine electrical power consumption and frequently about 10 per cent of total underground mine operating costs. The requirements for ventilation-related horizontal and vertical development, fans and cooling have a significant impact on mine capital costs and also on mine schedules and start-up times and hence cash flows. There are increasing pressures on regulators and miners to reduce airborne contaminants such as diesel particulatematter, nitrogen dioxide and heat (wet bulb temperatures), and significant pressures to reducegreenhouse gases such as fugitive methane emissions from coalmines and the carbon dioxide footprint of both coal and metalliferous mines. Many previously Australian miners are now globaloperators and have extensive overseas mining operations where local ventilation standards and expertise may not be consistent with Australian practices. The role of the site ventilation officer is also changing with strict new requirements for the statutory position being introduced into Queensland metalliferous mines and the potential for this to become more widespread. Recent regulator and parliamentary review committees have identified systematic shortcomings in mine ventilation compliance, and statutory certificates in both Queensland and NSW now require continuing professional development to maintain currency. Public and investor support for mining are also increasingly contingent on safe, healthy and environmentally responsible practices and the standards for these are frequently tightening. Good ventilation design and operating practices that are consistently well executed therefore contribute significantly not only to a safe and healthy mine but also to a productive and cost-effective operation and the ongoing social licence to operate. There are a variety of ways of providing technical design and oversight into a mine’s ventilation systems; this paper explores some current trends in ventilation standards and statutory requirements, as well as ways to support and develop mine ventilation staff for both domestic and international operations and also the emerging senior technical roles of Group/Principal/Corporate mine ventilation engineer.

Oct 12, 2022

By A. S. Tawadrous

This paper is an evaluation of Artificial Neural Networks (ANN) as a tool in the design of the geometry of surface blast patterns. The built model uses eight different parameters, which affect the design of the pattern. Those parameters are rock type, stratification, blasthole diameter, bench height, type of explosive, priming position, powder factor and fragmentation size required. The network was trained to predict burden and spacing of the blast pattern. The model was built and trained (back-propagation technique) using 43 case histories collected from the literature. The model has then been validated using 16 cases from operational quarries.

Jan 1, 2006

By D James

Fletcher Challenge Limited through its subsidiary Grampian Mining Co Limited has carried out an ore evaluation of one of New Zealand's largest known deposits of ilmenite located at Barrytown on the West Coast of the South Island, New Zealand. The ilmenite is located in a beach sand environment which has previously been mined for gold. Two analytical techniques were developed to quantify the resource. Considerable difficulty was experienced in this phase of the evaluation due to the presence of major inclusions within the ilmenite grains. Wet and dry concentration circuits, utilising spiral, wet magnet, high tension and plate electrostatic separators have been designed to produce ilmenite from the ore. Studies to utilise the titanium content of the Barrytown ilmenite have been made. Recent work has been directed towards a titanium dioxide pigment process.

Jan 1, 1986

By L. Rademan

The kinetic leaching behaviour of a low-grade surface gold ore and a high-grade reef ore were evaluated to determine the achievable gold recovery from these ores and particularly mixtures of these ores. The reef ore material has a head grade of 13.40 g/t with a relative standard deviation of 3%, and the unprocessed surface ore material a head grade of 0.43 g/t with a relative standard deviation of 15.6%. It is concluded that the kinetic leaching behaviour of these free milling gold ores during cyanidation, is not influenced by mixing of reef and surface ore material. No statistically significant relationship exists between the achievable recovery by direct cyanidation and the head grade of the material fed. No ideal ratio of surface ore to reef ore could be established. It is recommended that these materials should be processed simultaneously to minimize the costs, security risks, and losses incurred in transportation.

Jan 1, 2012

By R. Altindag

In rock cutting mechanics, the effects of the rock and coal brittleness on the efficiency of cutting bits are examined by many researchers. There is no universally accepted brittleness concept as a measure of cutting efficiency. The effect of the brittleness on rock cutting has not been completely explained. The aim of this study is to correlate the relationships between Specific Energy (SE) and brittleness concepts. The applicability of various brittleness measurement methods for rock cutting efficiency has been investigated. In this study, the raw data derived from previous experimental studies were used, and the relationships between SE and brittleness concepts were investigated. The two previously used brittleness concepts, which are named as B1 (the ratio of compressive strength to tensile strength) and B2 (the ratio of compressive strength minus tensile strength to compressive strength plus tensile strength), and a new introduced brittleness concept named B3 (the area under line in relation to compressive strength and tensile strength) were evaluated in this study. The relations among these brittleness concepts for rock cutting efficiency were established using regression analysis. There is no correlation found between the SE values and the brittleness of B1and B2values. But, the SE is strongly correlated with the brittleness of B3. It was seen that the suggested brittleness of B3concept could be used as an indicator in rock cutting efficiency analysis.

Jan 1, 2003

By Klaus Tietz, Hamish Adam, John Selby, Ian Glazier, Brian Sinfield

"Room-temperature tunable diode laser (TDL) analyzers are gaining in acceptance for highly critical safety monitoring applications in a variety of industries. This paper describes the testing, evaluation and deployment of a laser-based hydrogen cyanide monitoring system at the Campbell Complex of Goldcorp’s Red Lake Gold Mines in Balmertown, Ontario, Canada.A trial, single channel installation was followed by a staged multi-channel installation. Unexpected technical issues with the multi-channel installation were addressed and resolved.INTRODUCTIONLaser-based gas detection has several advantages over existing gas detection techniques (Ballangrud, 1993; Silver, 1992; Bomse, 1995; Table 1). For practical purposes, lasers generate light at a single wavelength. Room temperature tunable diode lasers (TDL) emit light in the near infrared (NIR) part of the electro-magnetic spectrum. Many gases of interest, including HCN, NH3 and others, absorb energy in the near infrared (NIR). Each gas has a unique absorption signature, or spectrum, made up of a large number of individual “absorption lines”. A TDL can be tuned to select a single absorption line of a target gas, which does not overlap with absorption lines from any other gases. Therefore, laser gas sensing is selective and does not suffer from interference from other gases. The single-wavelength nature of laser light also means that laser gas analysers have a linear response over a wide dynamic range.Tunable Diode Lasers (TDL) generate only a few mW of power. However, all this power is concentrated at one wavelength, the wavelength where gas absorption occurs, resulting in high signal-to-noise ratios and short response times, typically of about 1 or 2 seconds (Ballangrud, 1993). This also means that long path lengths can be used, enabling accurate measurements of very low concentrations, even with weakly absorbing gases. Tunable Diode Lasers provide all the advantages of other semiconductor devices: they are small, solid-state devices, operate at room temperature, and have long-term reliability (over 15 years). Currently, they can be obtained for any wavelength throughout the NIR (700nm to 2000nm). Because many gases absorb in the NIR, the technique is widely applicable."

Jan 1, 2011

By LuisW. Pommier

The industrial wastes generated by the plating industry, the circuit board manufacturing industries and other related industries normally contain high concentrations of metals, which make them hazardous. The extraction of the contained metals and their separation may be achieved by both pyro and hydro metallurgical processes. Some of the industrial wastes, those rich in some metals like nickel for instance, are being treated like mine ore concentrates and are being fed to smelting furnaces. The slags from these smelter operations are hazardous. They have, however, special environmental dispensations issued by the regulatory authorities. Hydro-metallurflcal processes have been reported. They also generate a residue which is hazardous because not all the valuable metals are leached out and also, because "non valuable" components, like chromium, are less readily leached. Residues from the plating industry, containing nickel, copper. zinc, iron and chromium as the major constituents and also sodium and calcium, together with cadmium, cobalt, lead. manganese, magnesium, molybdenum, and potassium, have been processed for the extraction of the valuable components. The generation of electrolytic nickel, copper and zinc and also of ferric chloride and chromium oxide is reported. The operation is achieved by a caustic leach for the extraction of zinc, followed by a sulfuric acid leach for the extraction of nickel and copper. This acid leach also extracts the iron and some chromium. The nickel copper and zinc are rendered pure by electrolysis, the iron is oxidized for the production of ferric chloride and the chromium is recovered as an oxide. The leaching operation is performed in two stages, first at a pH of 2.5 to generate an electrolyte for the partial recovery of the metals and then at a pH of 0.5 for the complete extraction of the metals. This leaching operation generates a residue, which although small in volume compared to the initial feed, still contains traces of the valuable metals and a portion of the chromium which makes it hazardous. Additional leaching with hydrochloric acid or nitric acid is required for its complete dissolution. The other minor constituents mentioned are present in concentrations each of less than 0.1% and are handled as impurities in the process. The metals which are soluble at a pH 0.5 and precipitate between 0.5 and 2.0 are bled off. Other impurities will concentrate on the raffinate from the solvent extraction operations from whence they are bled off. These bleeding streams are hazardous and the "impurity metals" are now present in concentrations which would make them valuable, however, the size of these streams is so small that they do not warrant their processing, however they could be marketed to specialized smelters. The extraction of the valuable metals, of the hazardous constituents, the generation of a marketable mixture of minor constituents and the production of a non-hazardous residue for declassification is profitably achieved.

Jan 1, 1998

By Donald Leroux, Martin Suichies, Andy Trusiak, Chris Dechert

"In modem concentrators, the operation of flotation machines is often stabilized by simple control loops. Froth level, slurry density and aeration rate are all physical parameters typically controlled through classical PID loops. Few concentrators, however make use of advanced computing technologies for controlling the grade of flotation product streams. Technical challenges such as long process delay and the long and uneven sampling interval of on-stream XRF analyzers often restrain their implementation. Model Predictive Control (MPC) is known to have better performance than PID for controlling processes with long delays (such as flotation circuits). This paper describes the implementation of a multi-input/single-output (MISO) MPC algorithm and an FIR model identification routine using an object-oriented graphical computing environment.The MPC module (controller and identification) was implemented on an industrial control system and applied to many sulfide flotation circuits in the Brunswick Mining concentrator (New Brunswick, Canada). In most cases, the manipulated variable was the collector addition. As long as it is provided with decent process models, the performance of the MPC controller is good on all the flotation circuits on which it was applied. Significant reductions of grade variance are reported and the controller responds well to set-point changes. The user-friendly, graphical nature of the computing environment led to a high degree of acceptance by both the process engineers and the flotation operators.1. INTRODUCTIONOver the past three decades, much instrumentation has been developed for flotation machines. The introduction of instruments such as pulp density gauges and cell level probes was particularly well received by the plants where pneumatic and electronic controllers were available for implementing PID control loops. In a way, these simple loops revolutionized the mineral industry. The operation of flotation circuits could then be stabilized through the use of automatic controllers."

Jan 1, 1999