Search Documents

By Robert J. Timko, Charles D. Taylor, Edward D. Thimons, Tom Mal

A test system was developed for measuring airflow in the National Institute for Occupational Safety and Health (NIOSH) ventilation gallery using a three-axis ultrasonic anemometer. The gallery was used to simulate face airflow conditions in underground mines having a blowing curtain. Airflow data collected at multiple sampling locations between the face and the end of the curtain were used to draw airflow profiles for different curtain setback distances, intake flow quantities and entry widths. In addition, methane was released at the face, measured at the sampling locations, and displayed as methane distribution in the area between the curtain and the face. Entry geometry had a significant effect on airflow patterns, and the flow patterns affected the distribution of methane in the entry. Flow measured at and parallel to the face was a good predictor of methane dilution and removal within two feet of the face.

Scenario reduction is designed for selecting a representative subset of geostatistical simulations out of a much larger set. Three steps are involved: measuring the dissimilarity between two simulations; finding a metric to measure the distance between any subset of k simulations and the full set of N simulations; and finding an efficient algorithm for selecting the subset that minimizes the metric. This paper focuses on the third question. We show that genetic algorithms are an efficient way of approaching the minimum when the population of subsets to be sampled is large. Two case studies based on the Walker Lake data-set are presented: firstly choosing k=4 simulations out of a total of 100, and secondly choosing 20 out of the same 100 simulations. In the first case it was possible to compute all possible combinations exhaustively and hence to demonstrate that the algorithm converges to the true minimum. This was not possible in the second case. Instead we demonstrate that it outperforms the random draw algorithm used in earlier work. A procedure for tracking individual selections during the iterative procedure was developed. This allows us to measure the evolution in the percentage of progeny resulting from crossing-over and from mutation that survived in the next generation. It gives valuable insight into how to choose the parameter values in the algorithm. Another key finding is that there is a trade-off between the number of individuals per generation and the number of generations required for the algorithm to converge.

Jan 1, 2014

To form a true picture of the early history of Queensland, we must think of white settlement advancing like an incoming tide, wave by wave; each wave lapping ahead a little further than the last. The credit for opening up the country belongs to a large number of pioneers, each of whom pushed out just a little further than his predecessors.Contrary to what one might expect, Rockhampton district was settled by overlanders from the south and not from the ocean side. When the Archers, the pioneers of the Rockhampton district, reached Gracemere in 1853, settlement had already made its way down the valley of the Dawson River; for it was from Leith Hay's station at Rannes (a few miles below Mount Morgan) that the Archers advanced northward into the unknown, to find the river that the explorer, Ludwig Leichhardt, had told them must enter the sea somewhere near the Tropic of Capricorn.The Archers travelled northward from Rannes up the valley of the Dee, coming out on the edge of the Razorback Range not very far from the point at which the Dawson Valley Highway drops over into Poison Creek. (Their diary records the bearings from a lookout point to various peaks around Rockhampton, and to-day, by plotting back from these peaks, we can determine the exact spot at which they descended on to the Fitzroy Flats.) We can be certain, then, that they must have been the first white men to set eyes on Mount Morgan; though to them it would have seemed to be nothing more than an insignificant hill...

Jan 1, 1939

By James Westfield

Drilling for roof bolting has created a new dust problem for the coal-mining industry. Drilling is inherently dusty, and control of dust produced by drilling vertical or nearly vertical holes is much more difficult than control of that produced by drilling flat or down holes.4/ Also, the dust produced by roof drilling differs in composition from that produced by drill-fur, or cutting the coal face because it contains a significantly greater amount of free silica and therefore presents a greater potential hazard of silicosis. Roof bolting has been practiced successfully in the mines of the St. Joseph Lead Co. in southeastern Missouri for over 20 years, but it was not until 1947 and 1948 that large-scale roof-bolting experiments were conducted in coal mines.5/ Although the need for dust control in conjunction with roof drilling was recognized from the beginning, the development and acceptance of roof bolting progressed so rapidly during 1949 and 1950 that solution of the dust problem lagged behind other engineering phases of the technique.

Jan 1, 1951

By J. -C. Trickett

The high-resolution three-dimensional (3-D) seismic reflection data acquired for Impala Platinum between 1998 and 2002 in the western Bushveld Igneous Complex form an integral part of Impala?s mine planning and development programme. These data are of sufficiently high quality to provide unprecedented 3-D models of the geological structure of the Merensky Reef and UG2 Chromitite Reef, from which the mine deduces the size, geometry and distribution of mineable blocks. Conversely, the seismic data details zones of un-mineable ground caused by structural disturbances in the form of potholes, fault zones and pegmatoid intrusions. Furthermore, variations in dip and strike are well imaged, allowing the mine planners to optimize the mine design and layout. Current interpretation work is focused on enhancing the accuracy of these geological models even further through the analysis of ?seismic trace attributes.? Preliminary testing on the Impala Platinum 3-D seismic volume has shown that attribute analysis has the potential to illuminate a number of geological reef disturbances that are otherwise ?invisible? in the original seismic time volume. Potential areas of improvement include inter alia: ?Improved definition of major fault zones ?Improved definition of zones of reef depression (?slumping?) ?Identification of reef terracing and/or reverse dip. Keywords: 3-D reflection seismics; Impala Platinum Ltd; seismic attribute analysis; seismic micro technology (SMT); rock solid attributes; dip-azimuth; instantaneous phase and similarity.

Jan 1, 2005

By R. L. Castro

Block caving methods, when operated under favourable rock mass conditions, can achieve higher production rates and lower operating costs than other various existing underground mining applications. For this reason, it has been considered the preferred method for the mining of deep and large orebodies in current and future operations around the world. One of the key aspects in the design of block caves is the selection of the production level layout, which, among other parameters, is based on the gravity flow characteristics of the caved rock. This is because gravity flow has a large impact on total ore recovery and the amount of dilution in a caving operation. Today, there are a number of computer based methods which aim to emulate the gravity flow pattern of the caved rock. In this paper, the authors present the development of FlowSiman improved model of gravity flow based on the cellular automaton approach, to estimate dilution entry, mixing and ore recovery. As part of the model development, flow simulations were conducted and subsequently compared to full-scale data collected at two mine sectors operated by Codelco Chile. The results indicate that by using proper calibrated parameters, good correlations between simulated and measured grades as well as dilution entry are obtained. The potential use of the numerical tool to evaluate drawpoint spacing in terms of recovery and dilution for block/panel caving operations is also presented.

Jan 1, 2009

By S. L. Ducummon

Inactive underground mines now provide essential habitat for more than half of North America's 44 bat species, including some of the largest remaining populations. Thousands of abandoned mines have already been closed or are slated for safety closures, and many are destroyed during renewed mining in historic districts. The available evidence suggests that millions of bats have already been lost due to these closures. Bats are primary predators of night-flying insects that cost American farmers and foresters billions of dollars annually, therefore, threats to bat survival are cause for serious concern. Fortunately, mine closure methods exist that protect both bats and humans. Bat Conservation International (BCI) and the USDI-Bureau of Land Management founded the North American Bats and Mines Project to provide national leadership and coordination to minimize the loss of mine-roosting bats. This partnership has involved federal and state mine-land and wildlife managers and the mining industry. BCI has trained hundreds of mine-land and wildlife managers nationwide in mine assessment techniques for bats and bat-compatible closure methods, published technical information on bats and mine-land management, presented papers on bats and mines at national mining and wildlife conferences, and collaborated with numerous federal, state, and private partners to protect some of the most important mine-roosting bat populations. Our new mining industry initiative, Mining for Habitat, is designed to develop bat habitat conservation and enhancement plans for active mining operations. It includes the creation of cost-effective artificial underground bat roosts using surplus mining materials such as old mine-truck tires and culverts buried beneath waste rock.

Jan 1, 1997

The Application of Roasting Pretreatment for Antimonial Refractory Gold and Silver Ores

Sep 13, 2010

By Emilie S. Williams

The Doyon Mine?s Zone 1 (Altered Zone), found along the southern boundary of the mine, encompasses approximately 20% of the mining reserves. The mineralisation is found in a series of steeply dipping narrow veinlets, which are contained in an extremely weak host rock: a sericitic schist with RQD values ranging from 0 to 20. Longhole mining methods are used, with either longitudinal or transverse approaches, depending on the width of the ore zone. Dilution is of critical importance in the mining of this zone, particularly in longitudinal stopes, where dilution levels have averaged 55% since 2000. Major factors influencing dilution in this zone include the stope geometry and standup time. A two-phase approach has been developed to mine and backfill longitudinal stopes: the top of the stope is pastefilled after approximately half of the broken ore has been extracted; the remainder of the ore is extracted once the plug has cured; and the remaining void is filled. This method has been used in six stopes to date, resulting in an average dilution of 17%. This paper details the application of this technique and its effect on dilution.

Oct 1, 2004

By Ish Grewal

The ACACIA Reactor - Introduction What is it? The Acacia Reactor is a fluidized bed high intensity cyanide leaching system. Purpose for its existence? The Acacia Reactor was developed to treat high grade gold concentrates generated from primary gravity concentration systems. Why intensively cyanide leach a gravity concentrate? Current secondary upgrading processes, such as tabling, create significant losses of fine gold that is initially recovered in the primary gravity concentration units. Additional benefits include improved security and a reduction in health hazards associated with calcining.

May 1, 2002

Before presenting this address I desire to express my appreciation of the honour which has been conferred on me by my election as iPresident of The Australasian Institute of Mining and Metallurgy. At this stage it might not be out of place to recall that Broken Hill was the birthplace of The Australasian Institute of Mining and Metallurgy, originally formed as the Australasian Institute of Mining Engineers in 1893.In selecting for my address the topic of "The Broken Hill Mining Industry and its Contribution to the Economy of Australia" I realise it is impossible to cover fully every aspect of the nation's economy which owes all or part of its origin to the Broken Hill field. Nevertheless, I feel that some attempt should be made to give credit to the Broken Hill mining industry for its part in the progress which Australia has made over the past seventy years.. If we care to reflect for a moment it soon becomes apparent that, not only is the Broken Hill mining industry an important producer of base metals for domestic and overseas consumption, but its profits have provided the means whereby many of Australia's leading secondary industries have been established or built up. Examples which come to mind are the founding of the iron and steel industry by the Broken Hill Proprietary Company; the establishment of plants at Port Pirie in South Australia, and at Risdon in Tasmania, for the production of metallic lead and zinc; and also at Port Kembla for the smelting of copper ores. From profits derived from operations at Broken Hill, capital has also been provided to assist other new essential...

Jan 1, 1956

By Paul Billingsley

THE purpose of this paper is a comparison, based on genesis, of the ore deposits associated with the igneous rocks of the central Montana Rockies. Considered separately, without attention to their origin, the orebodies appear to be distributed haphazard, with no fundamental laws controlling their position and character. It is believed, however, that if all the factors be weighed, this apparent confusion will to a large degree disappear. The, first essential to such a comparison is detailed knowledge of the individual mines, as to their geographic position (see Fig. 1), their mineralogical character, and in particular the derivation of their ores.1 The authors of this paper have pursued such an investigation for the past 6 years, and have accumulated a mass of evidence that enables a preliminary correlation to be attempted. It appears that the majority of ore deposits are genetically related to one or another of the igneous

Jan 4, 1917

By A. F. Brock

Introduction During the past ten years, shaft sinking has been going on continuously at Inco and new shafts and shaft extensions have been sunk under a broad diversity of conditions. The Murray mine and the Stobie section of the Frood-Stobie mine have?been opened and a main hoisting and supply shaft has been sunk at each of these mines; No. 2 shaft at Murray was sunk initially from surface to 1,960 feet and is now being extended; No. 7 shaft at Stobie was sunk from surface to 3,105 feet. No. 2 shaft at Garson has been extended from 2,200 feet to 3,200 feet in depth. At Levack, No. 2 shaft is being extended from 1,860 feet to 2,850 feet for ore hoisting from the 2,650 lev el. At Creighton, No. 6 shaft, collared on 52 level, was sunk 1,740 feet to a total depth of 5,563 feet below surface. It is the deepest Inco working. At Creighton, also, No. 7 shaft is being sunk from surface to the 30 level to handle the ore from caving operations. Ail Inco main hoisting and supply shafts sunk during the past twenty years have been vertical rectangular shafts equipped with two cages and two ore skips. The cages are standard and interchangeable for all shafts except Garson No. 2; they are single-deck, 13 ft. 4 in. by 5 ft. 2 in. inside and are designed to carry a maximum material load of 16,000 lb. The man load is 48 men. Skip capacities at the several shafts vary from 8 to 15 tons. Forty-two hundred feet bas been established as the standard vertical lift, and the permanent hoisting equipment at each shaft is designed for eventual hoisting from that depth.

Jan 1, 1950

By J. M. McKinley

Mineral exploration programmes around the world use data from remote sensing, geophysics, and direct sampling. On a regional scale, the combination of airborne geophysics and ground-based geochemical sampling can aid geological mapping and mineral exploration. Since airborne geophysical and traditional soil-sampling data are generated at different spatial resolutions, they are not immediately comparable due to their different sampling density. Several geostatistical techniques, including indicator cokriging and collocated cokriging, can be used to integrate different types of data into a geostatistical model. However, with increasing numbers of variables the inference of the crosscovariance model required for cokriging can be demanding in terms of effort and computational time. In this paper a Gaussian-based Bayesian updating approach is applied to integrate airborne radiometric data and ground-sampled geochemical soil data to maximize information generated from the soil survey, enabling more accurate geological interpretation for the exploration and development of natural resources. The Bayesian updating technique decomposes the collocated estimate into two models: prior and likelihood models. The prior model is built from primary information and the likelihood model is built from secondary information. The prior model is then updated with the likelihood model to build the final model. The approach allows multiple secondary variables to be simultaneously integrated into the mapping of the primary variable. The Bayesian updating approach is demonstrated using a case study from Northern Ireland. The geostatistical technique was used to improve the resolution of soil geochemistry, at a density of one sample per 2 km2, by integrating more closely measured airborne geophysical data from the GSNI Tellus Survey, measured over a footprint of 65 x 200 m. The directly measured geochemistry data were considered as primary data and the airborne radiometric data were used as secondary data. The approach produced more detailed updated maps and in particular enhanced information on the mapped distributions of zinc, copper, and lead. The enhanced delineation of an elongated northwest/southeast trending zone in the updated maps strengthened the potential for discovering stratabound base metal deposits..

Jan 1, 2014

By Martin van Staveren

In today's rapid changing construction world, the business pressures on piling and deep foundations reach sky-high levels. Ever increasing complexity of construction projects do severely contribute to these business pressures. Projects are often constructed in densely populated areas and located close to vulnerable buildings and infrastructure. The inherent uncertainty of ground conditions plays a dominating role in these foundation projects. Effective risk management is a key success factor for profitable and sustainable operations of piling and deep foundations. It starts with a fundamental requirement to be aware of risks. Next the different risk perspectives of all stakeholders in any foundation project have to be acknowledged. A simple and structured risk management approach is introduced, to demonstrate that effective risk management is not necessarily that complicated. A major element is the contractual allocation of risks, as a result from differing ground conditions. It is based on the so-called Geotechnical Baseline Report (GBR). The main objective of the GBR is to provide a clear contractual arrangement for the allocation of risks, arising from differing site conditions. The benefits of explicit risk management in general and contractual risk allocation in particular are illustrated with an example and experiences. The presented structured risk management approach, including contractual risk allocation, is still rather new. It proves to be promising for cost-effective risk control of piling and deep foundation projects, anywhere in the world.

Jan 1, 2006

By O. Ogunsola, M. Downing

This paper gives a brief overview of impacts of coal blending on coal-fired power plants performance and discuses the preliminary results of an on-going study aimed at evaluating the effect of coal properties on the effectiveness, compatibility and thermal reactivity of coal blends. Plant survey studies reported no significant impacts on an existing plant designed for a high rank coal when switched to a blend of low- and high- rank coal. However, slight modification of some aspects (handling, fuel storage/stockpile, transportation, preparation, and general housekeeping) of plant design and operation may be necessary. The preliminary results of an on-going study at the Mineral Industry Research Laboratory shows that more compatible and better blends could be made from coals where ranks are closer than from those where ranks are far apart.

Feb 24, 1997

By J. Restrepo, N. Ripepi

"The International Organization of Standards defines risk as “the effect of uncertainties on achieving objectives (15).” In mining, many uncertainties can influence the outcome of personal or professional objectives and are often difficult to predict. Risk management, the minimization and control of adverse effects from exposure to identified risks, is a well-established concept that can summarized as “being smart about taking chances” (12). Risk management now consists of management processes unique to numerous organizations across many industries, as varying sectors encounter a variety of needs, including the analysis and mitigation of risks related to physical security, product liability, information security, various forms of insurance, regulatory compliance, and workplace safety (12). The reoccurrence of multiple fatality events in the US mining industry, especially the underground coal sector, suggests an opportunity for improved methods of major safety hazard identification, assessment, and mitigation. A risk management approach would include ready identification and mitigation of these risks, inclusive stakeholder engagement, and rapid integration. While many solutions to reducing the risk of mine disasters have been proposed including stricter regulation and improved technology, a comprehensive risk management approach has yet to be fully integrated in the US mining industry. In December of 2006, R. Larry Grayson of the National Mining Association’s Mine Safety Technology and Training Commission called for “a new paradigm for ensuring safety in underground coal mines, one that focuses on systematic and comprehensive risk management as the foundation from which all life-safety efforts emanate (7).” A risk management approach has already been implemented with success in Australia’s minerals industry as part of a transition during the mid-1990s from a prescriptive based health and safety attitude to a more proactive, duty-of care [risk-based] philosophy (13, 16, 17).FUNDAMENTAL ELEMENTS OF RISK MANAGEMENT TECHNIQUES The fundamental components of a comprehensive risk assessment/management program are well-established within the realm of mining health and safety. Figure 1 depicts the elements of a typical mining hazard management framework. The first step in any safety-based risk management system is to identify and assess hazards by their location, nature, and magnitude within a mine. Next, a decision is made about choosing to eliminate, mitigate, or tolerate each hazard. Ideally, a hazard will be eliminated during the design stages of mining, though dynamic mining conditions often require continuous improvement and reevaluation of existing hazard controls. If elimination is not possible, hazard mitigation actions can consist of methods, rules, equipment, competencies, or other mechanisms. If a hazard is simply tolerated, as many inherent mining hazards must be, then specialized administrative controls must be utilized to minimize losses. During this process, the performance of each action is monitored and modified as needed (13)."

Jan 1, 2015

By G. Castillo, G. Thies, C. Bissue

"Newmont’s Phoenix mine began gold production in 2006 and has since experienced difficulties in reaching design throughput due to variability in ore hardness. In 2010, a debottlenecking study was conducted, generating multiple options to increase throughput of the existing Phoenix Mill through a series of phased expansions. An option was selected in early 2011 to increase the current concentrator capacity by approximately 25% through two phases. The first phase of the project was the installation of a secondary crushing and screening circuit in order to reduce SAG feed size from a P80 of 6 inches to 2 inches. The second phase focuses on downstream unit operations in the concentrator aiming to relieve existing bottlenecks such as flotation. This paper analyzes the design, commissioning, and operation of a recently installed SAG Pre-crush circuit (Phase 1). The design discussion will focus on concept development, flowsheet design, design criteria, process models, design limitations, and control philosophy. Discussion on the integration of operating data and flowsheet into design during engineering will be presented. Actual operating data of major equipment is gathered from the commissioning and operation of the circuit and compared to the initial design models. Conclusions will be drawn on equipment design factors used during engineering, and the success of model integration into operation. The paper concludes on the successes of the project and where improvements can be made during design.INTRODUCTIONThe Phoenix mine is located within 25 miles of the town of Battle Mountain, Nevada. The mill processes copper, silver, and gold ore. Production started in 2006 and has since struggled to reach the designed tonnage of 33,600 stpd due to the variability in ore hardness. In production year 2010-2011, the Phoenix mill average daily throughput of 33,000 stpd. In 2008, a larger primary crusher (FLS 60/89 gyratory crusher) was installed to operate in parallel with the originally supplied primary crusher (Metso 50/65 gyratory crusher), in order to provide additional capacity upfront in the circuit so that the primary crushing circuit could keep up with the mill.In 2010, a mill debottlenecking study was completed to assess the various options that could be implemented to increase the current mill capacity. The study was completed in late 2010 and contained four tonnages that Phoenix could achieve through various expansion scenarios. A single option was selected in early 2011 to increase the mill capacity from 33,000 stpd to 48,000 stpd. The selected option looked at a four phased expansion that would increase the capacity of the Phoenix mill and address the mill’s current bottlenecks:"

Jan 1, 2013

By Peter F. Weiss, H. Riedler, I. M. Moschitz, A. Olsacher, G. B. Fettweis

CONTENTS : 1. NATURAL FACTORS Geology Petrography and Rock Mechanics Mining System Orientation Rock Bolting System Movability of the Ore Grain Size Distribution Permeability Contamination Value of the Ore Hydrology 2. TECHNICAL FACTORS Height Length and Width Drawing Areas Time Factor Water Predrainage Surf ace Draining Underground Draining Advancing Slitting Sequence of Development Initiation of the Caving Process Drawing Rate 3. SPECIFIC MINING RULES Advancing Development Drawing Rate Interruption of Drawing (Water Distribution, Concentration of Mud, Dilution) Blasting 4. CONTROLS Safety Controls for Operation Computerised Drawing Control Structure of the Computer Program Hard Ware Print Outs 5. SUMMARY 6. ACKNOWLEDGEMENTS 7. REFERENCES Under the heading "Development System for Block Caving under Severe Conditions" a report was presented to this congress regarding a magnesite mine using block caving for several years. On account of the experience gathered in this mine and the results of far reaching exchange of experience, as well as under due consideration of the international literature it is tried to systematically list and briefly discuss the following factors that have to be considered for development and draw control of block caving. 1. NATURAL FACTORS It is self evident that this implies all those circumstances given by nature and which cannot be altered by man. Any mining activity is subjected to those and the success is depending on how far technology can be adjusted to those conditions. Geology Deposits of considerable thickness with rather steeply inclined flat-faced contacts are optimal for block caving. While vertically there is practically no limitation- for the deposit, theoretically, the smallest horizontal basis apt for operating block caving is the minimum area necessary to get the rock to completely cave in by undercutting and drawing. Practically, only consider- ably bigger main dimensions are found, mainly because of technical factors (machinery and equipment) and economic factors (cost ratio of exploration vs. development, danger of contamination).

Jan 1, 1981

By Lewis V. Wade

This paper summarizes the results of the rock mechanics monitoring program performed as part of Old Ben Coal Company's longwall coal mining demonstration project conducted in cooperation with the United States Bureau of Mines. The work described herein included installation of instruments, collection of data and data analysis performed during mining of the first longwall panel in Mine No. 24. The rock mechanics monitoring program included both surface and underground instrumentation and was designed to achieve the following purposes: 1 -To provide the capability to observe unusual situations during mining so that remedial measures could be instituted quickly 2 -To formulate design guidelines for future longwall mining efforts; 3 -To evaluate surface subsidence, and its character, rate and potential effects on cultural features, and to develop criteria to assist in predicting subsidence for other mines having similar roof conditions. Six previous attempts with longwall methods in Old Ben Coal Company's Hine 21 had been unsuccessful due to roof control problems. A description of these attempts is given by Moroni (1973). In preparation for the present longwall operation a study was performed to review existing data on the previous unsuccessful attempts, to establish coa1-and floor-strata bearing capacities in Mines Nos. 21 and

Jan 1, 1977