Search Documents

By Ali Kazmi, Wern-ping N. Chen

A load rating procedure was performed to evaluate safe load capacity of the Port of Miami Tunnel (POMT), FDOT Tunnel No. 871071 SR 887. The rating procedure performed on a total of eleven stations beneath roadways and with fill depth less than the tunnel exterior diameter (42 ft). Calculations on tunnel sections passing beneath roadways were performed to evaluate the structural response of the sections subject to moving vehicular loads, dead load, and earth pressures. Ratings were performed in accordance with AASHTO and FDOT guidelines. The procedure considered two types of vehicles (HL-93 and FL-120) and two rating levels (Design level and Permit level). As part of HL-93 vehicle, Tandem load was also considered for rating, separately. For HL-93 and HL-93 Tandem, inventory and operating level ratings were performed. The results show rating factors are high. The minimum rating factor is 16.8 using Inventory truck HL-93. For Permit level using FDOT FL-120 truck the minimum rating factor is 6.9. As can be seen, rating factors are higher than comparable analysis for bridges. This paper explains how the procedure can be implemented for tunnels and evaluates the rating results.

Dec 1, 2022

By David Chapman, Glen Frank

Due to the transport mechanics of the depositional environment, glacial soils display a very wide range of grain sizes and behavior. Several nonstandard drilling, sampling, and analytical techniques are therefore required to characterize the subsurface. The paper summarizes the geotechnical investigation for the design of a large project in glacial geology, which will include both large and small diameter pressure balance tunneling. The paper focuses on the challenges presented by the glacial environment and the techniques required to identify and characterize it for design and contract document preparation.

Jan 1, 2001

By Peter Faust

The foundations for the new South Viaduct Bridge in San Francisco were extremely challenging due to the requirement for very large and deep piles installed adjacent to historic structures. Drilled shafts up to 12? foot in diameter were constructed to a maximum depth of 200? feet in alluvial soils and Franciscan Bedrock using an oscillator system for the installation of the permanent steel casing. This paper provides an overview of the construction techniques, the equipment, and the challenges associated with constructing 12? foot diameter shafts on this very complex project in one of the nation?s nicest landscape setting.

Jan 1, 2011

By Randall Wheeler, R. Frank Chiappetta

2000 HIGH-TECH SEMINAR Blasting Technology, Instrumentation. and Explosives Applications - Orlando, Florida, USA July 24 - 27,200O 2000 BAI - PROTECTION AGAINST LITIGATION WITH GOOD PRE-BLAST SURVEYS, DAMAGE INSPECTIONS AND RECORD KEEPING 1 of 65 Good Record Keeping is Essential for: 1 ) Compliance with any prevailing Local, State or Federal Regulations, ordinances and permits. 2 ) Protection against potential litigation. 3 ) Balancing explosive consumption, use & costs. 4 ) Use in blast designs.5 ) Blast diagnostics & troubleshooting good/bad shots.

Jan 1, 2000

By A J. Eggers

With gold first discovered at Carrick in 1864, exploration and mining on the Carrick Goldfield in Central Otago, New Zealand, has now been ongoing for more than 130 years. Recorded historical hard rock production from up to 52 different mining claims from 1864 to about 1921 is 24,047 ounces (oz) of gold.   Since 1980 Amoco Minerals New Zealand Limited, CRA Exploration Pty. Limited, Amax Gold Mines New Zealand Limited and Summit Gold (New Zealand) Limited have conducted modem systematic exploration campaigns targeted at locating shear controlled gold bearing quartz lodes and stockwork deposits. More than NZ $1million has been spent by these companies on aerial photography, geological mapping, stream sediment surveys, soil and rock chip geochemistry as well as reverse circulation (RC) percussion and diamond drilling.   RC drilling by Summit Resources in 1997 has identified a 1,500 m long zone of low-grade gold mineralisation at Lower Carrick, with an average grade of 1.00 g/t Au over a 14 m average thickness. This gold mineralisation, hosted within a low angle shear zone, has analogies with the Hyde-Macraes Shear Zone in eastern Otago. Recent exploration and drilling at Carrick has revealed the potential to discover large (>0.5 million ounce (Moz)) low-grade bulk shear controlled quartz vein and stockwork gold deposits similar to those now being mined at Macraes.

Jan 1, 1997

A series of electron beam, cold hearth, single melt Ti-6Al-4V plates (nominally 2.5 cm thick) impacted by 2cm diameter, 4340 steel projectiles (with 54g nominal mass) at velocities ranging from 0.633 to 1.027 km/s were sectioned along the impact axis and examined by optical metallography to characterize the formation, growth, and microstructure of adiabatic shear bands. Near ballistic limit velocities, the shear bands propagate towards the rear of the target where they coalesce and grow to provide a cylindrical solid state flow regime for the plug volume.

Jan 1, 2006

By Peter White

Mine Planning Shaft Collar Shaft Sinking Raises Ramp Underground Water Storage

May 1, 2009

By J Jones

A common problem in the mining industry is that company exploration groups operate in relative isolation to the rest of the company; resulting in poor knowledge transfer (Qureshi and Briggs, 2006) and often priority conflicts with mine geology, operations and project departments. In recognition of this problem, Newcrest created a Minerals Division responsible for stewardship and governance of mineral assets across the value chain from reconnaissance to rehabilitation. It was recognised at an early stage that effective collaboration both internally and externally would be required to improve decision making, deliver faster cycle times and improve governance.Collaboration in companies is generally associated with the introduction of new IT functions. However, modern IT-based collaboration systems and practices are relatively simplistic compared to the long-standing practices associated with collaboration and knowledge management in science and engineering disciplines such as geology and mining.The authors of this paper have started a trial of a 12-point plan for effective collaboration, which recognises that significant efficiencies can be gained and barriers to future success removed if more effective collaboration can be achieved between science and engineering divisions in a company along with external professionals and with the collective intelligence (Tapscott and Williams, 2006) of the outside world. To meet growth aspirations some companies, like Newcrest Mining Ltd, are adopting this comprehensive, step change approach by moving from a closed model the isolates mine geologists to an open and collaborative model that uses IT visualisation systems strategically. The paper describes how an open model provides people with the right work environment and the right information at the right time, which will help individuals and workgroups to work more collaboratively day-to-day. The aim is to achieve speed, focus and mitigate risk through an environment where everyone and anyone can contribute effectively (Cisco, 2008).

Aug 22, 2011

The ore milled from the Lead Lode of The Zinc Corporation leases consists of a fairly granular mixture of galena, marmatite, chalcopyrite, tetrahedrite, pyrrhotite, pyrite, and lollingite with a gangue association of calcite, quartz, bustamite, rhodonite, mangan-hedenbergite, garnet, fluorite, mangal1o-calcite and apatite. The silver content of the ore occurs in three minerals-tetrahedrite, dyscrasite, and pyrargyrite, the last two mentioned occurring in microscopic association only. Other metallic and gangue minerals are also present in this complex mineralogical association, but do not influence the milling operations. Fortunately, the silver minerals favour the galena and chalcopyrite as their host minerals, thus facilitating the recovery of both copper and silver in the lead concentrate. The ore from the Lead Lode assays from 14-18% lead; 3·0-4·5 oz. silver per ton, and 9·5-12·0% zinc.A parallel lode, known as the Zinc Lode, is well developed in The Zinc Corporation leases. This lode assays from 6-8% lead, 1·5 oz. silver per ton, 18-25% zinc with a siliceous gangue. The common Lead Lode gangue minerals-ealcite, rhodonite, bustamite-are very rare in present underground exposures. No metallurgical work was done on this ore during the pilot plant operations.The aim in the milling process is to produce: 1. A lead concentrate with the maximum economic recovery of lead, silver, gold, copper and antimony, and minimum zinc content.2. A zinc conc,entrate with the maximum economic recovery of zinc, cadmium, and cobalt, and minimum iron, arsenic and fluorine content.3. A waste residue containing sufficient granular material to be utilized as underground fill.In considering the economics of the milling practice the above three requirements plus consideration of the tariffs submitted by the purchasers of concentrates were the deciding factors in the evolution of the present milling practice.Towards the end of 1924 The Zinc Corporation Limited added to and adapted the old zinc tailings plant for the treatment of 5,000 tons of crude ore per week. This plant, which operated until January, 1936, was in general principles similar to the standard Broken Hill methods of ore concentration, whereby the galena was recovered by the gravity concentration methods of Hgging and tabling with selective flotation concentration of the residual galena and marmatite. One important difference from other Broken Hill plants was that the primary grinding of the jig tailing was performed with flint-loaded mills operating in closed circuit with revolving screens. Two primary grinding sections were installed, each...

Jan 1, 1941

By Donald Leroux, Dave Scott, Giovanni Di Prisco

"The Lady Loretta lead-zinc deposit in Northwest Queensland, Australia contains an average of 5.9% lead, 17.1% zinc and 97 g/t silver. Ore mineralization is mostly comprised of fairly complex intergrowths of pyrite, sphalerite and galena. Starting in 1998, Noranda Inc., the major joint venture partner of the project, conducted extensive metallurgical test work, which culminated in July - August 2000 in a series of Pilot Plant tests. A common thread to all the metallurgical work has been the deportment of a large portion of silver into non-payable metallurgical products. Average silver distribution from four Pilot Plants shows a distribution of silver in lead concentrate of 28%, whereas silver in zinc concentrate was 49%, and 23% in the final tails.The consistently poor silver recovery as well as the fairly unusual silver distribution, particularly in zinc concentrate, was considered an issue to be thoroughly investigated. A mineralogical plan was devised to determine if these particular metallurgical results were somewhat related to the nature and mode of occurrence of silver carriers. Work was performed to determine discrete silver-bearing minerals and/or silver contained in solid solution in a suite of commonly occurring sulphides. Ore microscopy, SEM methods, Electron Microprobe and Ion Microprobe analyses were all used to answer these questions, and to find the silver carriers, so a metallurgical plan could be devised to improve silver recovery.INTRODUCTIONPotential economic exploitation of the Lady Loretta deposit in Queensland, Australia is driven by revenue derived from zinc and lead flotation concentrates and co-product silver recovery in lead. Relatively low recoveries of payable silver to lead concentrate, and high silver distribution to zinc concentrate necessitated an investigation into the natu"

Jan 1, 2002

By John Wilson

"The unconformity beneath 75 per cent or over 6000 km2 of the Athabasca Basin in Alberta lies within economically exploitable depths. The basement beneath this unconformity consists of an extension of the Wylie Lake Pluton, locally faulted and containing areas of mylonitic rocks. While the rocks of the Wylie Lake Pluton are not promising host rocks for uranium ore deposits, the areas of mylonites, graphitic rocks and possible remnants of granitegneiss would bear closer examination. One area of maficmylonites shows a weathering zone enriched in Si, Ca, Na, Pb, Ni, Ba, Co, Sr, Zn and U in addition to reported values of 0.08 oz/ton gold. This zone occurs beneath 800 m to 900 m of Athabasca Group sediments, but similar rock types are present beneath much thinner cover elsewhere. Detailed geophysical exploration is required over the area of thinner Athabasca Group rocks to define more precisely the areas of promising basement rock type.IntroductionThe Athabasca Basin in Alberta has considerable economic potential which has not yet been realized. The geological setting is closely analogous to parts of the basin in Saskatchewan which host major uranium deposits. Recent advances in geophysical techniques have led to deposits being located in Saskatchewan below 600 m of cover. This means that the unconformity between the Athabasca Group and the basement lies at exploitable depths over 6000 km2 or 75 per cent of the Alberta portion of the basin. Much of this area was only cursorily examined almost a decade ago. In addition, Alberta's new Metallic Mineral Regulations have clarified the regulatory situation in the area, and opened up much land for exploration. This article is based on Wilson's (1985a) study of the Athabasca Group and Wilson's (1986) work on the basement and alteration beneath the Athabasca Group in Alberta."

Jan 1, 1987

By D. Harrington

A uniform hoisting-signal code for mines hoisting from more than one level, if adopted by all mining States, would be beneficial to employees and owners alike and should largely reduce the number of hoisting accidents. Misunderstood hoisting signals cause many shaft accidents involving injuries to men, damage to equipment, and loss of production from the resultant delay. Many of the metal-mining States have adopted codes for hoisting that are effective within the borders of that State but usually entirely different from the signal code, if any, in use in an adjoining State. For many years safety engineers have recognized this lack of uniformity as a distinct hazard, but a uniform code has never been adopted by the States or by the mining industry in those States that have not incorporated signal codes in their mining laws or mining regulations.

Jan 1, 1944

By Brendan Demich, MAHIYAR F. NASARWANJI, Alan G. Mayton

Nonfatal injuries from slips, trips, and falls (STF) that occur at surface mines can result from inadequate lighting. Mobile equipment operators are among the occupations associated with the nonfatal incidents reported to the U.S. Mine Safety and Health Administration (MSHA). In addition, getting on/off the equipment (ingress/egress) frequently adds to the highest proportion of nonfatal incidents. Accordingly, researchers at the Pittsburgh Mining Research Division (PMRD), National Institute for Occupational Safety and Health (NIOSH) conducted a field study to investigate lighting on haul trucks and wheel loaderswith regard to glare and illuminance levels recommended by the Illuminating Engineering Society (IES). The objective was to determine whether two light-emitting diode (LED) area luminaires—a Mr. Beams® (model MB390 Ultrabright) (area luminaire-1) and a NIOSH-developed Saturn (custom-designed for a mine roof bolter study) (area luminaire-2)—could complement a headlamp luminaire. Measured levels of visual tasks, with the headlamp alone and the area luminaires plus the headlamp, demonstrated that illuminance met or exceeded IES-recommended levels. Nevertheless, the area luminaires illuminated a much broader area, which is key to increasing hazard awareness. Discomfort and disability glare were lower with area luminaire-1 than with area luminaire-2. Differences in glare were more noticeable for newer models of haul trucks and loaders featuring updated ingress/egress system designs. This study demonstrates that commercially available luminaires, such as area luminaire-1, are capable of complementing headlamp lighting, and can thus improve a miner’s ability to detect and avoid STF hazards.

Jun 17, 2020

By R. G. Tarr

During an intense and accurate study of initiation systems used on an AngloGold mine, Mine A, poor drilling practices were revealed. Graphic results of all actual measurements taken are shown below. [ ] Accurate drilling of shot holes will determine whether a mining operation is payable or not and at what pay limit mining can take place. Losing 30 cm of a potential 120 cm-hole length will result in a number of consequences, i.e.: ?Higher stoping costs ?Drilling of one shot hole twice in every five shifts ?Increased explosive cost as a result ?Excess stress on hangingwall and footwall due to bad face shape ?Excessive blast damage before the area is worked out. No wonder we have such a high-risk operation. Drilling accuracy is crucial to the profitability on any mine as profits are directly related to the quality and utilization of the drilled shot holes.

Jan 1, 2000

By P. Tsang

The mechanisms and functions of yield pillar are analyzed by employing finite element method that takes time dependent and plastic failure of rock into consideration. The design criteria for different geological conditions are discussed. The results provide further evidences that yield pillar design will improve floor or roof condition, especially when the floor and/or roof strata are weaker than the coal. Based on this study, the yield pillar size is determined for one cod1 mine located in southern West Virginia.

Jan 1, 1989

By Bengt H. Fellenius

Session 2, Deep Foundation without Soil Excavation, has attracted no fewer than 22 papers dealing with subjects from soil improvement by grouting, injection, and deep mixing techniques through vibroflotation and special piles, including aspects pertaining to conventional driven and bored piles. In the short time available, it is not possible to both do justice to the papers and provide a critical review of the state-of-the-art. Instead, to meet the objective of making the next half hour worthwhile to the audience, I have chosen to comment on a few special points brought forward in the papers and thereafter to discuss more in detail a couple of aspects I have deemed to be of general interest. Four papers deal with jet-grouting, injection, and deep mixing techniques: DOMSKI, J. J. Reinforcement of subsoil under the foundations of historical buildings in Cracow using deep injection technique. RESTELLI, A. B, BERTERO, M., and LODIGIANI, E. Deep mixing technology to improve the bearing capacity of a very soft clayey soil under an earth embankment.

Jan 1, 1994

By D. Bienstock

The Fischer-Tropsch synthesis is practicable in a reactor where the exothermic heat of reaction is removed by circulating large quantities of recycle gas through a catalyst bed of high-voids content. At an hourly space velocity of 1100, the feed gas, a mixture of 1.5 parts hydrogen to 1 of carbon monoxide, was converted 90 percent, producing hydrocarbons predominantly in the gasoline range. At these conditions a recycle-to-fresh gas ratio of 40:1 was enough to give excellent temperature control with a pressure drop of 1.5 p.s.i. per foot of bed using a steel catalyst in the form of lathe turnings. Steel parallel plates, although offering lower resistance to gasflow, were less reactive and less durable. INTRODUCTION The Federal Bureau of Mines has been engaged in a research and development program since 1944 on the synthesis of gasoline from coal. Gasification of coal with steam and oxygen to yield a synthesis gas--a mixture of carbon monoxide and hydrogen--is being investigated at Morgantown, W. Va.; and the synthesis of gasoline by catalytically reacting the carbon monoxide and hydrogen over iron by the Fischer-Tropsch reaction is being investigated at Bruceton, Pa.

Jan 1, 1960

By K. Saikiran, A. R. Nalla

Longwall management, regular shield maintenance, and evaluation of ground control problems can be performed using real-time shield monitoring program. Based on real-time shield pressure data, evaluation of intensity and interval of periodic weighting, estimation of time-dependent pressure increase and the effects of geologic anomalies can be obtained. In this study, full-face shield pressure data of over 457 m (1,500 feet) of face advancement is analyzed to evaluate shield response in the presence of surface lineaments, floor undulations, and multiple main roofs. Shield pressure increase due to web cutting is also correlated with setting pressure during periodic weighting and normal time. In addition, time-dependent pressure increase rate on Sundays and holidays is also correlated with time average pressure and the location of previous periodic weighting.

Jan 1, 2000

By J. R. Thoenen

Up to 1914 almost all of the world's supply of potash came from Germany and Alsace. With the cessation of shipments from Germany during the World War the importance of a domestic suppler was evident. During the past 15 years the United States has been working toward the establishment of a domestic potash industry which would end foreign dominance in this commodity. The Federal government has taken an active part in this program. As its share in the work, the Bureau of Lines has ascertained the potash resources in certain district's through core drilling and has engaged in a comprehensive program of research on the extraction of potash from its various minerals. Until the passage of the Winter bill (H. R. 496) by Congress in 1928 the Bureau of Mines had not been able to give any consideration to the western ores, wyomingite (leucite) and alunite. With the massage of this bill, however, the ray was opened for the extension of the potash studies to cover these materials.

Jan 1, 1932

By J. Postle, Deborah McCombe

"This is the third in a series of articles about the Committee for Mineral Reserves International Reporting Standards (CRIRSCO). The first article was an interview with Niall Weatherstone, Chairman of CRIRSCO (CIM Magazine, February 2008) the second described the background and goals of CRIRSCO (CIM Magazine, March/April 2008). In 2007, CRIRSCO was adopted as the Reserves and Resources Task Force of the International Council on Mining and Metals. This decision by ICMM has resulted in an increased level of funding for CRIRSCO and the ability to advance its objectives. In mid-October 2007, CRIRSCO members met in London England to discuss the status of each of the member countries’ reporting codes and the progress of various CRIRSCO projects. Update on national reporting codes Australia: The last update of the Australian JORC Code was in 2004. While there are ongoing discussions about issues that arise from the application of the latest version of the Code, there are no plans to update JORC in the near future. Canada: The Canadian Securities Administrators revised National Instrument 43-101 in December 2005. At the same time, the Canadian Institute of Mining, Metallurgy and Petroleum published updated Resource and Reserve Definitions that are incorporated by reference in NI 43-101. CIM is continuing work on developing Best Practice Guidelines to assist practitioners in the estimation of Mineral Resources and Reserves. South Africa: The South African Mineral Reserve Committee is currently awaiting an update of the Johannesburg Stock Exchange Limited Listing Rules, which will incorporate both SAMREC and SAMVAL (South African valuation guidelines). The official launch of both codes is expected in 2008. Europe: The Pan-European Reserves Reporting Committee expects to release a consultation draft in 2008. Emphasis is being placed on industrial minerals and aggregates, which constitute a very large industry in Europe. Chile: The Chilean Certification Code was approved in early 2008. As part of the Code, a National Commission is being established to screen and review reports on a random or specific basis. United States: The Society of Mining Engineers updated the SME Reporting Guidelines in 2007. The Securities and Exchange Commission has not accepted these more up-to-date definitions and guidelines. The SME committee will continue to discuss the incorporation of these Reporting Guidelines with SEC. SME has also established a class of membership, a Registered Member, which includes disciplinary measures for non-compliance with the SME guidelines."

Jan 1, 2003