Search Documents

By Y. He

The nature of the density distribution in a gas-solid phase fluidized bed for dry coal separation is an important factor in influencing the performance. However, during coal processing, fine slime would mix with dense medium of magnetite powder and accumulate in the bed, and its influence will affect the density of the bed. The mathematical model of the density distribution with fine slime behaviour was studied in an experimental laboratory system. The functional relationship between the density of the air dense medium fluidized bed and the coal slime content were fitted, applying the principle of least-squares method with damping factors. With the model, by analysing the trial testing data, the mechanism of the density distribution of the bed was studied and applied to a coal separation test with a pilot scale separator. Keywords: dry coal separation, gas-solid phase, model fitting.

Jan 1, 2002

By P. J. Lloyd

There are few data on the composition of discard coal in South Africa, and no overall view of the discards for the entire industry. As a result of work on coal qualities in South Africa, a database was established which enabled a good estimate to be made of the composition of the discard from every mine. The data are presented in the form of histograms of ash, volatile matter and fixed carbon content of the 43 million tons of material which were discarded in 1990. The results are discussed in terms of the closeness of the composition of much of the discard material to presently used power station coal. It is concluded that it is mainly developments in equipment, particularly fluidized bed boilers, which inhibit the wider use of discard coal. However, other factors must be noted, including the relatively high sulphur content of the discards, and the fact that even with the most careful storage the material ages and may become unusable after about 15 years.

Jan 1, 2000

By Frank S. Wartman

"The experimental flotation work described in this paper was undertaken to test the conclusions derived from a previous microscopic and chemical study of several samples of converter slag. That study3 resulted in the conclusion that approximately 90 per cent of the copper content of a converter slag wad in either the sulphide or metallic form, and that if the slag were cooled slowly the copper-bearing material would be in particles of such size that they would be freed from silicate and magnetite grains by grinding the slag to pass a 150-mesh sieve. If this were true, it should be possible to separate the copper-bearing grains from slowly cooled, converter slag by the flotation process.Many attempts, of which the author has seen no published account, have been made to treat slags, especially converter slags, by flotation. In every case these trials have been made with chilled slags, in which, as shown in the preceding report, the copper-bearing material is top finely disseminated, to be freed by any reasonable degree of grinding.The flotation tests described in this paper have shown that it is possible to recover by flotation about 30 per cent of the copper content of a converter slag containing 3 per cent copper and to obtain flotation concentrates which have a copper content of 35 per cent.Acknowledgment is made to G. L. Oldright, supervising engineer of the section of nonferrous metallurgy, U. S. Bureau of Mines, for valuable assistance and direction; to W. A. Sloan for chemical analyses; and to Alfred P. Towne for assistance in experimental manipulation."

Apr 1, 1931

By Kihong Park, Matthews C. Habjan, Arthur L. Miller

New Mining Safety and Health Administration (MSHA) regulations limit the mass concentration of airborne diesel particulate matter (DPM) or, more specifically, the concentration of elemental carbon (EC), in underground mines. The mine operators are responding by introducing a variety of controls to reduce DPM in the mines, potentially including the evaluation of new maintenance procedures to reduce underground mine vehicle emissions. There is currently a lack of an inexpensive and dependable method to directly measure the DPM concentration emitted from the vehicle tailpipe. To that end, this work demonstrated a simple field portable method for estimating the mass concentration of elemental carbon exiting the tailpipe of a diesel engine using a direct reading photometer. Simultaneous measurements of tailpipe exhaust were made with a Thermo Electron Personal DataRAM 1200 photometer (particulate mass concentration based on light scattering) and by analyzing PM2.5 and PM1.0 samples collected on quartz fiber filters using the National Institute of Occupational Safety and Health (NIOSH) method 5040 (mass concentration of EC via thermal-optical method). Results indicate surprisingly good correlation (R2 ) 0.97) of the two methods when the data are adjusted for relative humidity (RH) and corrected using an empirically generated calibration factor. Although preliminary, it may be possible to implement this method in maintenance shops to monitor emission trends and to compare emissions of various vehicles in a fleet. Such data will be useful for fleet planning to meet new air quality standards.

By William L. Saunders

MANY members of the Institute, who participated in the visit made, during the Bethlehem meeting of February, 1906, to the shops of the Ingersoll-Rand Company, at Phillipsburg, N. J., inspected with interest the new Electric-Air drill, which the company had set up for the purpose of showing it in actual operation to American. mining engineers. At the request of the Secretary of the Institute, I promised at that time to prepare a paper for our Transactions, describing the construction and advantages of the machine. But such a paper would then necessarily have contained much that was only expected or claimed by the designers and manufacturers of the drill, and not yet incontrovertibly proved by varied and long-continued practice. However moderate such statements might have been, they would have given inevitably to the paper, to some extent at least, the air of a prospectus, rather than of a technical contribution. I therefore decided, with the Secretary's approval, to postpone the writing of the promised paper until it could set forth the results of adequate actual practice, as well as the latest details of construction, etc., based upon practical experience. That period has now arrived. The Electric-Air drill has been exhaustively tested in the field, under varied and arduous conditions and upon the hardest rocks. It is now fairly in the field; its merits and performances are matters of unimpeachable record, and its place among established competitors can be definitely determined. As a representative of the Ingersoll-Rand Co., as well as a member of the Institute, I may be permitted to add that my company, being largely interested in the manufacture of air-

Jan 9, 1907

By P. K. Naik, B. Das

Flotation studies were carried out to recover carbon values from blast furnace flue dust containing ~30.34% carbon, 4.6% volatile matter (VM), and 65.03% ash. The variables chosen for the experiments were dispersant (sodium hexametaphosphate), pH, collector (diesel oil), and frother (MIBC). The experiments were designed according to a 24 full factorial design method and regression equations for the recovery of carbon and product grade were determined from the data. Experiments were performed to optimize recovery and grade using the steepest ascent method. The maximum recovery of carbon was 90.0% with a concentration of 56.5%, whereas the maximum obtainable grade of carbon was 66.35% with 50.45% recovery.

Jan 1, 2005

OVERVIEW OF PRESENTATION ? What is LMI ? Who uses LMI and how? ? Value of LMI to the Mining Industry ? Mining Industry Workforce Information Network (MIWIN) ? The Challenge: Forecasting the future in uncertain times ? Results: Hiring requirements in the next decade ? Results: Occupational information ? Next steps

May 1, 2009

By Ken G. Kress

Syphons can be a simple, reliable and proven alternative to otherwise more complex pumping systems or low level outlet works. In a simple form they consist of a pipeline constructed over the top of an embankment or high topographic feature, connecting a source pond to a receiving pond or channel (see Photograph 1). The syphon action is initiated by removing air from the pipeline (priming) using simple devices which can be purchased ?off the shelf?. Once primed, the syphon flow rate can be controlled or stopped using conventional gate, valve, orifice plate or other devices. Repriming is not required even if the flow is stopped, provided the syphon is not drained. A limiting factor in considering a syphon as a design option is the maximum lift (i.e., vertical distance from source pond level to summit of syphon) which is approximately 9 metres, or less, dependent on syphon pipe features and site conditions. Pipeline syphons can be quickly constructed from readily available materials including steel, polyethylene and PVC pipe. They are particularly well suited to many of the unique conditions often encountered at minesites. This paper identifies situations that can sometimes be best resolved using pipeline syphons. It provides basic principles for pipeline syphon design and includes case histories of their successful application.

May 1, 2001

The following observations on the mineral composition of the lead-zinc ores at Captain's Flat, New South Wales, are based upon the examination of a collection of specimens made during a brief visit to the mine in January, 1942, in conjunction with earlier studies of specimens and mill products, which have 'been the subject of various Mineragraphic Reports, Captain's Flat is about 35 miles south of Canberra, and is connected with the main line from Goulburn to Bombala by a branch line to Bungendore, 23 miles away from the mine.The geology of the mine has been described by Kenny and Mulholland2 and by Harper.3 The country consists of Silurian sediments, which have been invaded by a composite sill of quartz-felspar-porphyry. Both sediments and sill have been folded gently, the axial lines of the folds trending north and south. In the vicinity of the orebodies the folds are steeper, and thru,st faults are associated with the anticlines. The intense compression and shearing that accompanied the faulting has converted the adjacent porphyry to schist. The Captain's Flat orebodies occur along such a zone of shearing and faulting, on the eastern limb of a steep, north-pitching anticline. At their southern end the orebodies are enclosed in the slates underlying the porphyry, but the northerly pitch of the fold carries the slate to greater depth in the northern part of the mine, where the orebody lies beween schistose porphyry on the hanging wall and massive porphyry in the footwall.THE OREBODIESThe orebodies occur along a N.-S. strike length of 4,200 ft., and from the point of view of mining, fall into three sections: the Elliot's Section to the north, the Central Section, and the Keating's Section to the south. The Keating's Section is separated from the Central Section by 500-600 ft. of mineralised ground of so low a grade as' to be called barren, and is offset about 125 ft. to the 'east of the Central body by an oblique fault striking N.300E. Elliot's Section and the Central Section are connected by persistent veins and stringers of lead-zinc ore, but although these are...

Jan 1, 1943

By Y. M. Zhao

The separating performance of a pilot dry beneficiation system using a gas-solid fluidized bed was investigated with coal from South Africa. The coal used for the study has a low inherent moisture content, a moderate ash content, a moderate volatile content, a low sulphur content and a high calorific value. Its washability is moderate. Experimental results show that the separating quality of the fluidized bed drops gradually as the feed-coal particle size decreases. The probable error, E, values for 50?25mm, 25?13 mm and 13?6 mm coals were 0.04 g/cm3, 0.06 g/cm3 and 0.09 g/cm3, respectively. The cause of the differences in separating characteristics was analysed by particle dynamics and numerical modelling. Furthermore, the pilot fluidized bed was employed to separate 50-6mm coal. In this experiment the coal ash content was reduced from 23.74% to 11.79%, with a probable error, E, value of 0.07 g/cm3and a recovery efficiency of 98.26%. This indicates that the fluidized bed is applicable to the separation of coal from South Africa and has good separating performance and wide applicability. Keywords: feed-coal particle size; gas-solid fluidized bed; dry coal beneficiation; numerical simulation.

Jan 1, 2010

By Cem Colakoglu

In this study, nickel containing iron alloys were produced by carbothermal reduction of lateritic nickel ores obtained from Manisa - Caldag region of Turkiye in order to investigate the reaction mechanism of nickel and cobalt. In the experiments, the lateritic ore containing 1.58 wt.% Ni and 0.12 wt.% Co was calcined in a semi-pilot scale rotary furnace at 1100°C for 1 hour. Then, a mixture of calcined ore and metallurgical coke was reacted in sintered alumina crucibles using a graphite resistance tube furnace at different time (0- 60 min) and temperature (1500-1600°C).

Jan 1, 2009

By D. J. de Beer

South Africa had a late start with rapid prototyping (RP), with the first system being available in 1991. Up to 1994 only three systems were available in SA. Through active research participation from the CSIR and a number of universities, supported by technology transfer programmes and industry awareness workshops, adoption of RP technologies started to grow. Internationally, RP grew to the extent that several country-based member organizations were formed, and an initiation meeting of the Global Alliance of RP Associations (GARPA) took place during the SME Rapid Conference in Dearborn, USA in 1998. South Africa (SA) was invited under the auspices of the Time Compression Technologies Centre (TCTC) launched by the CSIR, and received an invitation to become a member of GARPA through the launch of a national, inclusive organization. The latter gave rise to a RAPDASA planning/launch meeting held at the University of Stellenbosch, which culminated in the first RAPDASA international conference held in November 2000 at the CSIR, and the election of a first RAPDASA management committee, also at the 1st AGM held during the conference. RAPDASA has been a pillar of strength since then, with an annual international conference being presented. As South Africa?s RP awareness grew through the RAPDASA and independent activities, so did the availability of RP platforms in SA.SA also became a benchmark for other countries/late adopters to follow, as slowly a position of following became a position of leading through innovative applications. The paper highlights SA?s development approach and history, together with the discussion of case studies in various fields. Contribution to the light metals industry will also be discussed. Keywords Rapid prototyping, additive manufacturing, product design, rapid tooling, rapid manufacturing, medical product development.

Jan 1, 2011

By Taylor R. G

This paper reports a biogeochemical study of the Siberia lode of the Herberton tin field. Soil near the orebody contained high levels of Fe, Cu, Pb, Sn, As, Mld Mn. Polycarpaea spirostylis and Indigofera dominii were associated with these high levels but several other species apparently could not tolerate them. The potential of these species as indicator plants is discussed.

Jan 1, 1975

By K. Morin

"Silver and gold leaching by cyanidation is a well-known process used around the world. This reaction is often accompanied by the leaching of other species throughtout the cyanidation circuit that causes the diversion of cyanide towards non valuable by-products (SCN-, Cu(CN)x, Fe(CN)x, etc.). One of the detrimental impacts of the formation of these by-products is the precipitation of silver-cyanide complexes that occurs when cyanide concentration is too low. Without any extra-addition of free cyanide, the precipitated silver is lost and cannot be recovered causing an important economic loss. To overcome silver precipitation, cyanidation circuits are often operated at higher cyanide concentrations. Recently, COREM’s research team has been working on a technology to measure and control silver precipitation during the cyanidation process. Moreover, a methodology has been elaborated in order to evaluate threshold cyanide level which corresponds to the cyanide concentration at which silver starts to precipitate. This technology has been tested on site on a real cyanidation circuit at Agnico Eagle’s LaRonde mine."

Jan 1, 2014

By A. Kapito

The formation of bainite in steel is dependent on the size of the casting, the heat treatment, and the alloying elements. It is difficult to obtain a fully bainitic microstructure in steels during heat treatment because of its close proximity to the martensite (a?) reaction. The ferrite (a) and pearlite reactions in steels are also rapid and shield the bainite reaction. Alloying elements therefore need to be added to separate the bainite reaction. Boron (B) and molybdenum (Mo) are key elements added to bainitic steels because of their ability to retard the a reaction. Other elements used in the production of bainitic steels are silicon (Si), chromium (Cr), manganese (Mn), and titanium (Ti). In this paper we investigate the effect of alloying elements on the bainite reaction through the use of dilatometry. Dilatometry is a technique that determines phase transformations in the steel and through which continuous cooling transformation (CCT) curves can then be developed. Some initial results are presented of an ongoing study on the development of bainitic steels for railway wheel applications.

Jan 1, 2013

By Joel Darmstadter

The position of the coal industry in America’s fuel and power picture remains one of prime importance. Measured in Btu terms, the industry is the country’s leading energy producer and an important exporter. Foreign coal sales yield annual proceeds of about $4 billion. Coal’s one-fifth share of the nation’s energy consumption is nearly as high as that of natural gas. Coal is the electric utility sector’s principal fuel supplier. It accounts for about55% of the electricity generated at power stations.

Jan 1, 1999

Titanium and Zirconium Industries Pty. Ltd. separates rutile and zircon from heavy mineral concentrate recovered from sand dunes on the east coast of North Stradbroke Island, Queensland. Separation plant feed is delivered to Dunwich, on the west coast, by a seven mile aerial ropeway traversing the island. Mining and concentration is effected by two floating dredge-concentrators now operating on the beach 31; miles from the aerial ropeway terminal. Heavy mineral concentrate is transported hydraulically from the dredges to the ropeway through a 6 in. pipeline. Six pumps in series deliver 24 ton/hr of dry solids in a pulp containing 13 per cent solids. For maximum economy the transfer pumping system is controlled deliberately to cause transportation in the zone of incipient settlement of solids, ieat velocities below the limit deposit velocity for the particular pipe diameter, pulp density, and specific gravity of solids. Automatic density control, based on a combination of power consumption and pipeline pressure, eliminates the danger of plugging the line but periodic flushing is necessary to remove gradual accumulation of solids in the bottom of the pipe. After 15 months operation the pipeline was descaled with hydrochloric acid to remove severe blistering with rust nodules, regrowth of which is now prevented by continuous injection of inhibitors. After transporting 100,000 tons of heavy mineral the average wear on the steel portion of the pipeline was 0·01 in. and indications are that wear on the asbestos cement portion is less.DESCRIPTION OF OPERATIONSGeographyTitanium & Zirconium Industries Pty. Ltd. (T.A.Z.I.) operates on North Stradbroke Island, some 30 miles southeast of Brisbane, Queensland. The island is approximately 25 miles long and eight miles wide, and is bounded on the east by the Pacific Ocean and on the west by Moreton Bay (Fig. 1). With the exception of a small outcrop of volcanic 1. Manuscript received at The Institute. 8th May. 1962. This paper was presented at the Annual Conference of The Institute. 5th-11th August. 1962.

Jan 1, 1962

By D. Harrington

For many years the Federal Bureau of Mines-in cooperation with other agencies-has been making investigations and compiling and publishing reports and statistics on accidents in the various branches of the mineral industry.4 Its assistance has been enlisted also in health, safety, and ventilation problems' incident to the driving of many large tunnels in the United States in recent years. As part of this work the Bureau has compiled considerable statistical and other information on accident experience in the tunneling branch of the heavy-construction industry. It has always been difficult to obtain up-to-date information on tunneling methods and tunnel accidents. Published accounts of tun¬nel construction furnish much interesting material of engineering, historical, or fiscal value, but usually little or no attempt is made to discuss and critically analyze the means taken to preserve the health and life of employees.

Jan 1, 1941

By W. P. Diamond, S. L. Cario, F. Garcia, J. D. Byars, T. P. Mucho

The National Institute for Occupational Safety and Health (NIOSH) has been conducting research at a Pittsburgh Coalbed longwall mine to evaluate and optimize bleeder ventilation and gob gas venthole longwall methane control systems. Gas flow into these two methane control systems was investigated using a combination of Sulphur Hexafluoride (SF6) tracer gas studies and gob venthole pressure monitoring experiments. The insights gained from this research has facilitated the development of along wall subsided strata methane control system conceptual model. This model provides the basis for design suggestions to increase the efficiency of the gob gas venthole system to permit the bleeder ventilation system to become a "safety net" for methane control.

By U. B. Kodukula

Attempts are made to evaluate the feasibility of using a water-injection cyclone for the concentration of iron ore fines. The separation characteristics of clay fines, containing large amounts of alumina and silica, from the iron values are discussed. The effects of critical variables, such as injection water rate, truncated cone diameter, spigot opening and vortex finder diameter, on the performance of a water-injection cyclone in terms of iron, alumina and silica grades; iron recoveries; and alumina and silica rejections are discussed. A set of 16 full-factorial experiments (24) was carried out to gain an understanding of the individual and interaction effects of the variables. The results indicate that classifying iron ore fines containing 63.0% iron, 2.5% alumina and 3.5% silica through a water-injection cyclone can produce concentrates with iron grades greater than 66.0% and alumina and silica contents less than 1.5% and 2.0%, respectively, at different study conditions. The achievable iron recovery values are greater than 88%, and alumina and silica rejections are more than 80% and 50%, respectively, within the specific study conditions. While the truncated cone diameter, injection water rate and spigot diameter influences the alumina rejection to a considerable extent, it is mostly influenced by the vortex finder diameter. The iron recovery and silica rejection values are mostly influenced by spigot diameter and truncated cone diameter. The effect of injection water on the concentration characteristics depend on the prevalent truncated cone diameter and spigot diameter conditions.

Jan 1, 2008