Search Documents

By J. -P. Saindon, L. D. Nel, A. E. Hall, S. G. Hardcastle

"This paper reports on an investigation into gas and dust concentrations in Ruttan Mine's exhaust air. The values obtained indicate that there is excellent potential to recirculate approximately 25% of the hot exhaust air into the intake air to reduce winter heating costs. Contaminant concentrations vary significantly during the course of the working shift and decrease in the mine exhaust system as the air returns to surface. A proposed on-line control system is outlined which would permit recirculation to be implemented with a pay-back period of less than two years. IntroductionIncreased energy costs and depressed mineral prices have resulted in mines, which use winter ventilation air heating, reviewing their systems to try to reduce costs. Heating costs can be significant, for example, Potash Corporation of Saskatchewan spends an average of $580,000 per mine per year and Ruttan mine spends approximately $IM per year on propane for its direct-fired heating system.Several method s of reducing heating costs have been considered and the following have potential application.Heat Exchange Between Exhaust andIntakeThis is usually accomplished by run-round glycol systems. The system is limited by ice formation on the coils in wet exhaust air and by the low exhaust air temperature, usually l0ºC. It also requires close proximity of the intake and exhaust airways to ma~e the cost of the connecting pipeline and pump systems economic . A feasibility study by Inco's Thompson operation reported that a proposed system of this type had a 19-year payback period and was, therefore, uneconomic. Potash Corporation of Saskatchewan is currently investigating plastic heat exchangers for a trial system because of corrosion on metal exchangers. It has the advantage of a 17°C exhaust temperature and relatively dry exhaust air.Waste Heat ReclamationThe waste heat from compressors and hoists can be used for heating in some mines. The feasibility of such a system depends on the individual layout and the proximity of the heat source to the inlet airway. Other mines have considered using the exhaust air in greenhouses to provide a cash crop."

Jan 1, 1988

By Fun-Den Wang

This report presents the results of two large scale field coal pillar strength tests (80 ft by 80 ft), the results of a series of laboratory small core sample tests, and the correlation between those field and laboratory tests. The concept of applying laboratory coal sample strength data to predict the in situ coal pillar strength appears to be feasible. The deformation property of large pillars can be obtained successfully by testing the coal sample in the laboratory within acceptable accuracy. There are prevailing directional strength and deformation properties in coal pillars along the butt and face cleat system.

Jan 1, 1976

By Geo. H. Williamson

This paper describing the dredging operation of J. K. Davison & Bro. on the Allegheny River near Pittsburgh, Pa., is one of a series being prepared for and published by the United States Bureau of Mines on methods and costs of dredging sand and gravel in the United States. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total costs might in many instances cause embarrassment to individual operators as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. ACKNOWLEDGMENTS The author wishes to acknowledge the assistance of H. R. Hissrich, chief engineer of the Goodman Engine and Machine Co., in compiling details of the dredge construction; of H. H. Stewart, auditor of J. K. Davison & Bro., in preparing cost and performance tables; and of J. R. Thoenen, mining engineer of the United States Bureau of Mines.

Jan 1, 1932

Up to 19 chemical parameters were studied in flotation pulps in six Australian lead-zinc concentrators with the aim of obtaining a better understanding of the nature of, and changes in, the chemical environment. This paperdiscusses pH, redox potential, and oxygen concentrations, which were all measured continuously.Two plants operated at natural pH in slightly acid circuit and one at natural pH in alkaline circuit, and pH was stable at all these plants. In two plants varying amounts of cement fill were present in mill feed and pHwas variable. At the other plant pH was controlled with soda ash and lime.Redox potentials became more positive as the pulp passed through the plant. The minimum change was 20 mV and the maximum about 250 mV. Potentials tended to be variable at any point early in the circuit, but were more stable later on. In some plants reagent additions had no noticeable effect on redox potentials. However in the two plants operating in acid circuit the redox potential of .zinc rougher feed was markedly affected by changes in copper sulphate addition rate. Sodium sulphite additions had an effect at other plants.Oxygen concentrations in grinding circuits tended to be low (30 per cent of saturation) and very variable. Flotation was usually conducted in pulps at least 90 per cent saturated with oxygen. Addition of sodium sulphite had a marked effect on oxygen content in one plant, but less effect in two others.Statistically significant relationships were found in some plants between pH and redox potential, redox potential and oxygen saturation, and oxygen saturation and pH.Improved control of copper sulphate and sodium sulphite additions could result from applications of this work.

Jan 1, 1970

The purpose of this report is to describe the work accomplished by Mine Safety Appliances Company under Contract No. H0110845. This contract required the design, installation and testing of a permissible mine surveillance and communication system for the USBM Bruceton experimental mine facility. While much of the design and operational detail of this system can be drawn from the instruction manuals delivered with the equipment, some of it will be repeated here in Volume I for the sake of clarity, but the principal objective will be to report on overall system and subsystem performance and to suggest design alternatives for future consideration. Details of the overall system design will be found in Volume II of this report.

Jan 1, 1973

By Giuliana A. Zelada-Tumialan

Reduced workability and flowability of the concrete through the tremie tubes and drilled shaft reinforcement have been identified as the main causes of tremie-concrete drilled shaft concrete defects. This paper discusses two recent case studies of defective tremie-concrete drilled shafts. The defects (soft inclusions, aggregate segregation, and low concrete strength) were primarily caused by the combined effects of the tremie placing sequence, rapid concrete slump loss, and poor passing and blocking characteristics of the approved concrete mix design. The level of detail contained in the drilled shaft specifications varied between projects. However, even when the specifications incorporated several of the more recent recommendations for tremie-concrete placement, the case studies showed that typical provisions for concrete mix proportioning and placement can be further improved to minimize construction defects such as those described in this paper. Based on the findings of the case studies presented, recommendations for the development of more effective specifications are provided. The recommendations include requirements for mock-up testing of proposed concrete mix designs and evaluation of the tremie-concrete placement sequence. Performance of such testing and evaluation would greatly reduce the potential for drilled shaft defects and consequent time and financial burdens associated with them.

Jan 1, 2009

One Hundred and Twelfth Meeting of the Institute, Monday, February 14, to Thursday, February 17, inclusive, 1916 COMMITTEE ON ARRANGEMENTS DAVID H. BROWNE, Chairman. BRADLEY STOUGHTON, Vice-Chairman. LAWRENCE ADDICKS, BURR A. ROBINSON, P. E. BARBOUR, E. M. SHIPP, G. D. BARRON, JOSEPH STRUTHERS, J. V. N. DORR, E. B. STURGIS, J. R. FINLAY 'R. H. VAIL. L. D. HUNTOON, Hotel Accommodations.-The Committee on Arrangements is canvassing a number of hotels in New York City, securing .wherever possible special rates to members and guests for the clays of the meeting. It is possible to secure good accommodations on very reasonable terms in New York City if one knows where to look for them. A list of hotels and rates will be published in the final announcement of the meeting, which will go to the members about the middle of January, in order that those who desire to secure good hotel accommodations at a reasonable mice may have the information.

Jan 1, 1916

By B. W. Gandrud

This is the third report published by the Bureau of Mines concerning the washability of Black Creek coal. Both of the former reports.5/6/ dealt with the Black Creek coal at the Bradford mine, Dixiana, Ala., near the northeastern extremity of the Warrior field, whereas the present report is based on float-and-sink tests of coal from what is presumably the Black Creek bed near the southern extremity of the field. Although the Yolande Coal & Coke Co., owners of the property at Yolande No. 6 slope, consider this opening to be on the Black Creek bed, the authors do not feel that there is as yet positive proof that this correlation is correct. There has been little or no development of the Black Creek bed in the Yolande Basin in the past, and a positive identification of the bed at Yolande No. 6 will have to await further exploration and development. The Yolande No. 6 is an exploration slope 3/4 mile north of Rockcastle, Ala. The slope is approximately 400 feet from top to bottom on a dip of 180. As far as the authors can ascertain, coal has never been produced commercially from the Black Creek bed in the southwestern part of the Warrior field. Exploration work in the past has indicated that the Black Creek coal in this area is extremely friable and high in sulfur. Extreme friability would naturally discourage its use as a domestic and railroad fuel, and high sulfur content would be a disasvantage in its use for coking coal. The present study of this coal has been made with particular reference to sulfur elimination on the assumption that it would make a good coking coal provided enough of the sulfur could be eliminated by washing.

Jan 1, 1939

The mineralogy of the rocks now observed in the Nairne pyrite deposit developed under conditions of internally-controlled sulphur activity during amphibolite facies metamorphism. In the sulphide-deficient metasediments the activity of sulphur was low, and pyrrhotite developed with iron-bearing silicate minerals. At higher sulphur activity, in the sulphide-rich meta-sediments, pyrite formed in addition to pyrrhotite, and the associated silicate minerals are iron-deficient.

Jan 1, 1969

By Robert M. Semple, Harvey W. Parker

INTRODUCTION Two promising innovative tunnel support systems are being developed by the Civil Engineering Department of the University of Illinois. One of these is a lining which can be placed by a slipform located immediately behind and contiguous with a tunneling machine. Recent advancements in construction materials appear to provide the breakthrough required to make such a system feasible and practical. The lining material which permits this construction scheme is wire fiber reinforced concrete made with high, very early strength regulated-set cement. Parts I and II of this paper relate to this slipformed liner. Part I discusses the material and equipment required to install the liner. The "Extruded Liner System" (ELS) has been devised to place the lining. This ELS concept is briefly described and a tentative development program is outlined. In Part II, the physical properties and practical construction aspects of the liner material are discussed and a program for structural testing of 10-ft diameter prototype tunnel supports is presented. Part III contains descriptions of improvements to conventional steel-rib tunnel supports. It is shown that square tubular box sections are structurally superior to wide flange sections for complex loading conditions often encountered in rock tunnels. Analytical studies and tests on connections have been performed to evaluate their structural behavior. These are presented along with a program for comparative large-scale tests on horseshoe-shaped frames with a 10-foot span. This research is being conducted by the Department of Civil

Jan 1, 1997

By Dale Preece

A carefully designed and controlled in-place destruction experiment was performed on a concrete bunker buried in 4.27 m (14 ft.) of soil. The objective was to determine if the explosive charges would collapse the structure in-place without requiring mechanical excavation. Collapse of the buried structure was first attempted by drilling holes in the soil and placing four 13.38 Kg (29.5 lb) Comp B explosive charges at a depth of 2.13 m (6.7 ft.). The configuration of the charges when detonated was 2.13 m (6.7 ft.) off the top of the concrete roof and 3.66 m (12 ft.) apart in a square pattern. Detonation of these charges created a crater ~4.88 m (16 ft.) in diameter and 2.13 m (6.7 ft.) deep, leaving ~2.13 m (6.7 ft.) of soil covering. Very limited spalling occurred on the ceiling of the concrete structure as a result of detonating these four charges. The second attempt to collapse the structure consisted of placing another single 13.38 Kg (29.5 lb) charge, identical to the first four, near the geometrical center of the bunker roof. This charge was detonated in the soil cover 100 to 200 mm (4 to 8 in.) above the reinforced concrete roof, collapsing it. Due to the collapsed roof and remaining soil cover, the structure had been collapsed in place, requiring no further demolition.

Jan 1, 2006

By G. A. Calboreanu

One way of cost reduction is attained when using materials with improved erosion ? corrosion resistance. For many years hard irons successfully answered the Mining Operation needs however application ranges were limited due to the low chemical resistance of such alloys. Corrosion resistance of any hard iron increases when microscopically homogenizing chromium and generating passivation conditions throughout and between all metallographic phases. Chromium distribution of the new material called Max10 was analyzed with EDS ? energy dispersive spectroscopy. At critical depleted chromium carbide ? matrix interfaces chromium increased to 31.72% which is well within passivation levels. Generally the corrosion resistance of high chromium hard irons provided by Metal Casting Industry is limited to 0.5% sulfuric acid and 28 PPM ionic chlorides. Such restrains increased when using Max10 to 2.0% sulfuric acid and 100 PPM ionic chlorides. Max10 contains 35% carbide volume fraction, has excellent corrosion resistance within pH = 1.15 ? 13.6 while fracture toughness under plain - strain conditions and Mode I opening is KIC = 20 KSI.(inch)1/2. Wear rate was calculated with the pin-on-disk apparatus using a diamond indenter per ASTM G99 recommendation. After years of research, experimentation and implementation the Max10 castings were service installed in slurry pumps and mixing equipment. In some applications the life time of slurry pumps manufactured in Max10 tripled versus previously used materials.

Jan 1, 2012

By M. Mononen, J. Huuskonen, M. Vauhkonen, J. Kourunen, A. Lehikoinen

"A new approach to measure process conditions in flotation cells is presented. Real scale flotation cells in a Zinc circuit are imaged using Outotec LevelSense sensors based on electrical resistance tomography. The latest results from long period plant tests show that the sensors together with FrothControl analysis give new information that correlates well with other process parameters. The sensors can compensate for electrical contact contamination using an automatic calibration technique and they are basically maintenance free. The results indicate that using the LevelSense sensors and FrothControl solution, the process control and optimization can be done automatically, stabilizing and improving the metallurgical performance of the flotation process.INTRODUCTIONThe froth flotation process is widely used in mineral industry for the separation of minerals from low-grade ore slurry. Different property parameters of froth and slurry could be measured to monitor and control the flotation process: air bubble size distribution, flow dynamics, thickness of the froth bed, amount of solids in the froth, etc. Some techniques already exist that can be utilized in studying these important parameters on-line. Examples of the techniques are the high-speed video imaging, simple conductivity probes, ultrasound techniques, floats and pressure transducers (Maldonado et al., 2008). These techniques, however, often suffer from some limitations. For example, the video imaging only gives information from the surface of the froth, simple conductivity probes suffer from contamination and the floats may get stuck and therefore do not give reliable signal for process control and optimization."

Jan 1, 2013

By Richard L. Ash

7.3-1. Introduction. All phases of mining competent materials are affected directly by the results achieved from primary blasts. It is imperative that their design suit each particular set of mining conditions. In general, the round design must provide an adequate tonnage of material, properly placed with suitable fragmentation, to ensure that loading, haulage, and subsequent disposal or processing are accomplished at the lowest possible cost. Blasting rounds are designed by the proper application of cratering relationships developed for the single, concentric, confined explosive charge. Blasting for surface mining and most open-cut heavy construction, however, is characterized by the use of rounds, composed of a number of explosive charges with relatively long lengths, which are placed in benches with specific finite dimensions. Therefore, modifications must be made to the classical, single point-charge cratering concepts. It is the purpose of this discussion to outline the basic principles, significant variables, and procedures for their integration in the design of rounds that are applicable to conditions characteristic of surface mining. Because relatively insensitive blasting agents will be used in most instances, particular attention must be given to priming, control of confinement, and selection of charge diameters that ensure complete explosive-reaction execution. 7.3-2. General Considerations. The primary requisites for any blasting round are that it ensure optimum results for existing operating conditions, possess adequate flexibility, and be relatively simple to employ. It is important that the relative arrangement of blastholes within a round be properly balanced to take advantage of the energy released by the explosives and the specific properties of the materials being blasted. There are also environ- mental and operational factors peculiar to each mine that will limit the choice of blasting patterns.

Jan 1, 1968

By Malte J. M Gurgel

Subsurface spatial planning is becoming increasingly important in view of competing underground applications. This development is influenced by global agreements to reduce greenhouse gas emissions. Therefore, precise knowledge of the underground space is a basic prerequisite for future applications. The three-dimensional registration and reliable georeferencing of underground infrastructures can establish a holistic geodata basis for such tasks. Those tasks are discussed both for the development of energy projects such as deep geothermal energy as well as for storage applications. Research on geothermal energy has been carried out at RWTH Aachen University as part of the SuperC project in a license field in the Aachen area since 2001. Recently, this research has been extended to include monitoring aspects in the overlapping GEObservatorium Aachen field. The documentation and visualization of underground activities using photogrammetric methods like Structure from Motion is discussed based on recent research in sites for the final disposal of radioactive waste. Finally, both applications provide an outlook on supporting underground projects by using high-resolution geodata.

Feb 1, 2025

By Douglas M. Dwosh

INLAND STEEL COAL COMPANY'S experience with a gypsum cement, with and without fiber glass filler, indicates that the concept of utilizing standard rock dust equipment to dry handle and apply gypsum cement as a mine sealant is feasible, simple and economical. Prior to 1975, Inland had casually experimented with a few sealants and had discussed the advantages and shortcomings of other sealants with various users. Hower in mid-1975, Inland foresaw the need to seriously acquire a practical sealant system. There were nearly a dozen sealant materials on the market at that time: silicate-based materials, Portland cements, vermiculite cements, gypsum cements, and magnesium-oxysulfate cements, each with their own fillers and additives. The applicating equipment ranged from simple to complex: wet mix or slurry machines operating on either a batch or continuous basis, high viscosity pumps, and pneumatic, dry conveying machines with water nozzles. Compounding the selection process, two or more products could often be used with the same machine, or a given material could be successfully applied with more than one type of machine.

Jan 1, 1976

By Gary Cavanough, Stuart Addinell, Hector Parra

Drilling deep, straight, accurate holes in hard rock to achieve efficient blasting is a challenge for the mining/quarrying industries with short holes normally drilled using “top hole hammer” (THH) and deep holes using “down the hole Hammer” (DTH).

Jan 1, 2013

By H. K. Lin

The effect of metallic iron fines on froth flotation of a sulfide ore was examined by comparing the flotation results with and without iron fines present in the flotation feed. Mild steel and ceramic laboratory ball mills were used to grind 600 g sulfide ore charges. The mild steel ball mill generated approximately 4.6 g of iron fines (0.8% of the ore charge mass) when grinding to a product size of 80% passing 200 mesh (75 mm). When a low dosage of a weak xanthate collector was used in flotation, the impact of the iron fines on sulfide flotation was marked. Higher dosages of stronger xanthate collectors rendered the impact of the iron fines much less significant. Consumption of the collectors by the powdery iron fines is believed to cause the differences observed in the flotation results. A galvanic effect on flotation was not evident in this study. The impact of the iron fines on silicates depression was also examined.

Jan 1, 2008

By D. M. Fritz

Environmental experts face large and rapidly-increasing volumes of raw data obtained from environmental monitoring stations. These professionals must compile and analyze the data in a systematic manner to cost-effectively understand and minimize the impacts of mining. The shift toward desktop computing, combined with the downsizing of company staffs, has now more than ever created a demand for a modern, PC-based application for the storage, retrieval, analysis and presentation of environmental data. This paper discusses the general requirements of such a system, and points out specific ways in which such industry-specific software can provide convenient and useful access to the data. The software used to illustrate these features is the HydroDat program, developed by Western Water Consultants, Inc.

Jan 1, 1996

AMONG the multifarious duties which fall to the lot of a mining engineer it is safe to say that there is none of more fundamental importance than the study of the ore-deposits on which it is thefunction of his profession to operate, inasmuch as the whole business of mining in all its complicated ramifications rests first of all on the existence of something to mine. -When the ore supplies in a mine fail, the enterprise comes to- an end, and nothing, therefore, is of more importance than a thorough understanding of the conditions under which the ore occurs, so that everything possible may be done to open up the mines well ahead of their immediate output requirements, and develop new ore reserves to take the place of that which is raised from day to day. The great aim which the mining engineer has to keep before him in his study of his ore-deposits is to obtain such a knowledge of them that he will have sound grounds for prediction as to how they will behave in parts of the mines which are well beyond the point of the pick. It is on his judgment of probabilities in this respect that mining operations are entered upon, and the more thorough his knowledge of all the factors affecting the problem, the more is the judgmentlikely to be a sound one. The test of any theory is experimental confirmation of the truth of predictions based upon it, and our aim should be to try to perfect our knowledge of the rules governing deposition of ores, so that our theories may prove themselves equal to the task of successful prediction.

Jan 1, 1909