Search Documents

By P. Bakke

Following extensive R&D efforts, Hydro Magnesium has launched a new alloy series with remarkable combinations of properties. The AE alloy family is based on additions of aluminium and rare earth elements to control mechanical properties, including elevated temperature creep strength. By combining these alloying elements with manganese additions, high purity alloys with outstanding corrosion performance are defined. A basic philosophy behind the developments has been to simultaneously approach all the critical issues related to developing a commercial material. Apart from the obvious requirements for material properties, the critical issues relate to die casting performance, as well as alloy production, recycling and environmental compatibility. Some of the important elements related to alloy production and recycling are addressed in the present paper.

Jan 1, 2006

By Joel Nonnweiler, Rafael Castro, Ross Webb

The three thousand foot long 66-inch diameter Folsom East Interceptor Section2B was completed accident free, on time and under budget with no measurable surface settlement. The tunnel passed through nested cobbles, highly abrasive sands and gravels, and abandoned mine workings with less than five-feet of cover at times. Preventing settlement was critical since the tunnel passed under a heavily traveled state highway. A pilot project to test microtunneling and pipejacking methods in the same ground conditions abandoned both drives before completing the planned drive lengths. This paper discusses performance of the conventional tunneling method selected to excavate the ground and the effectiveness of the ground modification techniques employed.

Jan 1, 2001

By Alexander Fleischanderl

Steel market has become somehow unpredictable and requires quick adjustment in production conditions to survive in the harsh market environment. Steel production is not anymore driven by output records, but by efficient cost reduction measures to remain competitive under strongly varying production conditions. Energy efficient production and flexible raw material scenarios have become decisive factors to succeed and survive in our industry. Such scenarios have to be carefully investigated to be well prepared to adopt production steps continuously. The paper analyses various process opportunities to optimize energy and raw material consumption in the production route. Off-gas treatment systems have still a huge untapped potential to recover energy from the hot waste gases. This is valid for the EAF mini mills as well as for the integrated route. Various examples for waste heat recovery systems including resulting benefits are discussed for the EAF, agglomeration, blast furnace, direct reduction and BOF. New innovative bag-filter systems feature extremely low emission levels at lowest pressure loss and sound emission conditions. Also improved control and automation solutions support the operators to minimize the operation and maintenance costs of their off-gas system. Steelmaking by-products shall not be considered as residues, but as a valuable and cheap raw material source. The paper presents some show cases how to valorize slags as well as utilizing coke and iron oxide fines to increase productivity and minimize raw material cost. A new process for highly flexible converter steelmaking allowing for extraordinary high HBI and scrap rates above 50% and improved yield is discussed and evaluated

Oct 30, 2017

By Cristiane Lazzaro Barbosa

Visando a melhoria contínua no atendimento a seus Clientes, além de garantir a confiabilidade e rastreabilidade do processo de tratamento das manifestações de seus clientes e dos sinistros ocorridos com os produtos adquiridos, a ArcelorMittal Brasil Planos investe na atualização do sistema que suporta este processo e na convergência para o SAP. O Projeto, denominado QM Comercial, utilizou os módulos QM, DMS, SD e WF do SAP ECC para implementar a solução de registro, documentação, elaboração do parecer com a análise de várias áreas/unidades da empresa e a orquestração das atividades dos processos comerciais/financeiros de conclusão da reclamação/sinistro. Todas as etapas com rastreabilidade e controle de tempo de resposta das áreas envolvidas.

Aug 16, 2017

The following notes apply more especially to the purchase of silverlead ores produced in the neighbourhood of Zeehan and Dundas; for it is this class of ore that is principally mined in those parts, and which creates competition among the ore buyers.In the early days of this field, most of the ore passed through the hands of the first buyer who had sufficient enterprise to establish himself at Zeehan but in more recent times, competition has been so keen that there are generally three or four buyers tendering. lf the output was large this would not matter so much from the buyers' point of view but when we consider that the output of the field is only some 1,650 tons per month, and that of this 70 odd tons are produced by the Western and Montana mines, aud being sent home for realization, is withdrawn from local purchasers, there is really not enough for four buyers, especially at the present exorbitant prices they pay the miners.Some of the mines have a fixed sampling day, on which it is tacitly understood that the ore buyers will attend. Others, such as Grubb's Silver Mining Oompany, No-Liability, send round a printed reminder, stating the quantity of ore, and the date of sampling.

By Mohammed Z. Islam

As cities are growing all over the world, the need for urban transportation facilities are on the rise. Designers (of these facilities) today are faced with a number of constraints for their design, of the most is the space limitation and impact of new construction activities to the community. A typical subway station, as the focus of this paper, is approximately 600 to 1000 feet long, 50 feet wide and 2 to 3 story high. With such a large volume of construction activities, it is easily realized why underground stations are becoming obvious choice for larger cities eventhough the cost could be 2 1/2 to 3 times as much as an aerial station and 4 to 5 times that of an at-grade station [O'Neil et. al.(1977)]. Since cost is an important factor which is always increasing, therefore, the designer should have a good planning, consider alternatives for design and come up with a realistic design with minimum impact to the community. This paper is about the geotechnical considerations that the designer should be aware of. PLANNING A 1977 report [O'Neil et. al.(1977)] on the construction costs for a number of underground subway stations indicate that about 4 0% of the cost is site-controlled, 35% is structural items, and 25% is finish and equipment. It is seen that of opportunity exists for cost savings in the site selection and proper use of the site. Once the site is selected, the cost of construction become controlled by urban conditions at the site, geotechnical conditions, station size and depth. Therefore, the design-solution is very much site-specific. The geotecnical designer should collect the following information at the early phase of the design:

Jan 1, 1993

By I. Dymov, W. Phillips

A process has been evaluated, on a continuous pilot plant scale, to treat refractory gold arsenopyrite/pyrite concentrates. The process consisted of biological leaching to partially oxidise sulphides, followed by pressure leaching for complete sulphide oxidation and arsenic precipitation, followed by liquor neutralisation and cyanidation of the autoclave residue for gold recovery. This paper provides a brief description of the treatment flowsheet and discusses some of the main parameters and results of the process. During integrated pilot plant campaigns, it was confirmed that acceptable sulphide oxidation and gold extraction of 96-98% could be achieved by a two-stage oxidation with BIOX® (4 days total retention time) followed by PDX (40 minutes retention time at 220°C). Only partial arsenic precipitation was achieved in the autoclave, followed by complete precipitation by neutralization under atmospheric conditions. The overall process could be significantly simplified, and capital and operating costs reduced, with a flowsheet modification allowing all of the BIOX® liquor to bypass the autoclave directly to the neutralization circuit.

Jan 1, 2004

By H. NORTON JOHNSON

THE oil industry in California during 1929 reached new heights and new depths in the discovery and development of the oil resources of the State. The discovery of new fields, and more especially the discovery and development of deeper prolific sands in known fields has, for the first time in its history, brought the potential production of completed wells within the State to over 1,000,000 bbl. oil per day. Constant improvement in equipment and technique has made possible economic development to depths unheard of but a few short years ago. Commercial production from a depth of over 4000 ft. was considered quite an accomplishment in 1923 when the Meyer sand at Santa Fe Springs was developed, and when later oil was successfully raised from this depth.

Jan 1, 1930

By M. Magnelöv, Du Sichen, U. Sjöström

An experimental study has been performed to investigate the behaviour and separation of inclusions at the interface between steel and slag. The study has been limited to liquid inclusions because they can be a potential problem in transient situations such as ladle changes in continuous casting of steel. Model experiments with water and silicon oils have been carried out to study the kinetics of separation of simulated inclusions at an interface. The properties of the inclusions and the slags have been varied by using different oils with different viscosities, densities and surface tensions. The effect of temperature of the liquids has also been examined. Measurements of the terminal velocity, rest time and the behaviour of the liquid inclusions at the interface have been recorded using a video camera. It has been found that the inclusions reach their terminal velocity early in the vessel and the experimental velocities differ somewhat from the values evaluated using ?intermediate law?. The results from the experiments have shown that the size of the inclusions has no appreciable influence on the rest time. Droplets of AK50 oil have been found to have considerably long rest time. A water film surrounding the droplet has been expected to be the main reason for the long rest time. The present study has also shown that the viscosity of the oil has certain effect on the rest time, but only to some extent, since viscosity has double functions. A higher viscosity provides higher resistance to the droplet entering the oil phase leading to longer rest time and at the same time damps the lateral movement of the droplet along the interface, leading to easier stabilization and shorter rest time. On the other hand, a high viscosity of the oil phase results in slow dissolution process. It has been concluded that a meaningful model of inclusion separation at the metal-slag interface must take the interfacial phenomena into consideration. Keywords: Inclusions, terminal velocity, rest time, dissolution.

Jan 1, 2004

By R. Altindag

Engineers and researchers need to estimate the mechanical properties of rocks from P-wave velocity. In previous studies, the researchers have investigated either the limited values or all the data belonging to sedimentary, igneous, and metamorphic rocks together in the same statistical analysis. In this study, the raw data pertaining to only sedimentary rocks was taken from previous studies and evaluated. For this purpose, a total of 97 samples of sedimentary rock types were subjected to statistical analysis. First, the relationships between P-wave velocity and physical-mechanical properties were investigated by simple regression analysis. All the data were then subjected to multi-regression analysis. Some empirical equations with high correlation coefficients were derived for rock engineers. The equations obtained from the analyses are compared with previous equations found in literature.

Jan 1, 2012

By D C. Grant, D J. Goudie, E Baird

The Scanning Electron Microscope – Mineral Liberation Analyzer (SEM-MLA) laboratory, as part of the Core Research Equipment and Instrument Training (CREAIT) network of laboratories at Memorial University, NL, Canada, has recently published efforts towards increasing the throughput of automated mineralogy systems by producing single-step trans-vertical moulds, rather than traditional 30 mm polished epoxy moulds. Due to the small particle size of iron ore grains in the -200 mesh size fraction (<75 µm), not all of the surface area on a mould is needed for measurement in achieving good statistical representation. In a new study, trimming of the excess area of a mould results in a smaller sample and increases the quantity of unique samples that can fit in a newly designed trans-vertical adapter for a FEITM MLA 650 field emission gun (FEG) scanning electron microscope. The complete analysis, using a newly designed sample block holder capable of holding 98 samples, required 57 hours of running time where each sample had an average of 33?400 particles measured and identified. The analysis was calibrated to allow for off-line discrimination of hematite/magnetite. The calculated Fe-assay values derived from MLA results were compared to those from bulk sample chemical assay. This shows the Fe assay having a correlation coefficient of >0.99 when the particle count is greater than 20?000. This study represents the most expedient method yet reported to prepare well-polished samples and analyse them in a timely manner that can allow for quicker results in process mineralogy.CITATION:Grant, D C, Goudie, D J and Baird, E, 2017. Analysis of individual - mesh iron ore samples in a single Scanning electron microscope automated mineralogy session, in Proceedings Iron Ore 2017, pp 535–540 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By G E. Ho, M Anda, S Dallas

Water auditing and water conservation measures are fast becoming the quantitative tools for water balance reporting in the mining and minerals processing sector. Therefore, this paper was written to describe the process of water auditing in a goldmining environment and to contribute towards building an appropriate water management framework for The Cooperative Research Centre (CRC) for sustainable resource processing (CSRP). The research will assist with the assessment of water balances in mining and hydrometallurgical processes and ongoing probabilistic modelling for Newmont Mining Corporation, its wholly owned gold mines, and its joint venture operation of Kalgoorlie Consolidated Gold Mines (KCGM). Kalgold or KCGM are the managers of a joint venture project between Barrick Australia (50 per cent) and Newmont Mining Corporation (50 per cent) at Kalgoorlie, Western Australia (WA). Boddington Gold Mine (BGM), Western Australia, will commence operations this year and manage the new goldmine expansion project. BGM is 100 per cent Newmont owned and will operate to continue mining gold and copper from the existing (BGM) site that was decommissioned in 2001.

Jan 1, 2009

By Yi Yang, CHENGLONG XU, HAORAN LI, YALI FENG, JINRONG JU

This study presents a method for recovering valuable metals and synthesizing anhydrite from steel slag using sulfuric acid leaching and solvent extraction. The process achieved high leaching efficiencies for V, Ti, Fe, and Mg, and produced anhydrite with 93.09% purity. The leachate was further processed to separate and recover V, Ti, Fe, and Mg using selective stripping and precipitation methods, offering a sustainable approach to steel slag utilization.

Jan 22, 2022

By M J. Begbie, P C. Keall, M P. Simpson

The Golden Cross low sulfidation epithermal deposit occurs in pervasively altered andesite of the Waipupu Formation and in the Waiharakeke Dacite. The unaltered, post-mineral Whakamoehau Andesite overlies these units. The Empire zone of the Golden Cross deposit contains a stockwork which is currently mined by open pit methods, and a series of veins that are mined underground. Alteration envelops both the underground and open pit mineralisation. The core of the alteration zone contains silicification, as quartz veins, and adularia. Shallow portions of the system contain illite-smectite and a thermally unstable chlorite, tentatively identified as corrensite, which pass downward into illite and chlorite, respectively. Replacement calcite occurs widely throughout the altered zone; pyrite is nearly ubiquitous. This alteration assemblage indicates formation from near-neutral alkali chloride waters. A late, post-mineralisation alteration assemblage of calcite, smectite, illitesmectite, kaolinite and siderite presumably formed from weakly acidic, steam-heated CO2-rich waters.   We have identified eight stages of vein formation: (1) sulfide veins, (2) black veins, (3) massive veins, (4) banded veins, (5) thin white veins, (6) crumbly veins, (7) massive/platy calcite veins, and (8) flattened rhomb calcite veins. Gold mineralisation occurred relatively early in the lifetime of the system, dominantly during 2 through 4. The late calcite veins (7 and 8) and early sulfide veins (1) are barren.  

Jan 1, 1997

By Victor Azbe

Introduction Lime enters our daily life in many ways. Our building, chemical, agricultural, sanitary, and industrial endeavours depend on it to such a great extent that it could probably be called the most important inorganic chemical, and the extent to which it is used might be considered an index of industrial development. Industrial limes vary greatly in quality, due to internal structure and other characteristics. They may be good or bad, sensitive or slow to react. While improper manufacture may not greatly alter the appearance of the lime, it may affect its properties considerably and thus its suitability in the many processes in which lime is used. In some of the processes, one kind of lime is wanted, in others another. While the nature of the stone from which it is made has much to do with whether a lime is suitable or not, its burning and hydration are the crux of the matter. Up to not so many years ago, the knowledge of lime burning was rather imperfect and it is only relatively recently that its manufacture is approaching the state of a higher industrial art. This slow development was in part due to lime manufacture being scattered among many small concerns who, independently, either lacked the inclination or could not afford to strive for a higher technical development.

Jan 1, 1946

By S. J. Page, R. A. Jankowski, J. A. Organiscak

The U.S. Bureau of Mines investigated the relationship of bituminous coal seam parameters and the amount of airborne respirable dust generated at longwalls. Dust and coal samples were obtained from 20 longwalls operating in geographically representative coalfields throughout the United States. Statistical analyses of coal seam parameters and airborne respirable dust measurements indicate a likely causal relationship between seam type and respirable dust. Low-ash, high-volatile coal seams were associated with higher airborne respirable dust levels. A negative linear correlation (significant at the 95-pct confidence level) was observed between the seam's ash content and airborne respirable dust, explaining up to 18 pct (R2 = 0.18) of headgate dust level variation and up to 15 pct of tailgate dust level variation. Volatile matter was found to have a positive linear correlation with tailgate dust level, explaining 16 pct of the variation. Further data examination indicates that these relationships with dust are most likely nonlinear, because of improved R2 values over the linear correlations. However, a notable portion of longwall dust production is influenced by other operational parameters, so additional research under more controlled conditions is needed to determine the seam's causative functions.

Jan 1, 1992

By J. B. Zadra

Tungsten metal, chemically equivalent to commercial grade, is produced by electrolysis of impure tungsten compounds or scheelite in an alkali, phosphate or borate electrolyte. A preliminary investigation of fused-bath electrolysis shows the effect of electrolyte composition, temperature, and current density on current efficiency, yield, crystal structure, and purity of product. Experiments show that tungsten can be electrowon from scheelite in a fused alkali, phosphate, or borate bath with similar results. Studies on electrolyte composition show that the addition of sodium chloride is essential to both electrolytes in treating scheelite. Although its main function is to react with or flux the CaO, it also increases the bath fluidity. Temperature studies revealed optimum ranges between 900° and 1,100° C.; 900° C. proved satisfactory for tungsten trioxide, and 950° to 1,050° C. for scheelite. Current efficiencies were satisfactory for all current densities ranging from 10 to 57 a./dm.2. Yields were 400 to 650 g./kw.-hr. over the same current-density range. Crystal size and purity of the product are functions of temperature, current density, and amount of impurities in the electrolyte. Deposited crystals vary in shape from spherical grains to clusters of dendritic hexagonal needles, and in size from smaller than 35 to 570 microns. The purity of the tungsten metal produced ranges from 99.7 to 99.94 percent.

Jan 1, 1959

An incremental analysis based stope design optimization method was developed at Exodus, an underground project located 30 miles north of Carlin, Nevada. Traditional underground stope design methods, by manually drawing stope shapes, are typically very time-consuming and lacking of consistency and accuracy. For quick reserve calculation and economic analysis, a new method named '3D Incremental Analysis based Stope Optimization' was created for mine wide stope designs at Exodus. With this unique but practical method, multiple options of mine designs were completed within a short period time, which allowed us to select the optimal cutoff grade and best stope design option for the project.

Jan 1, 2012

Few, if any, reliable thermodynamic data are available for the activity of tin oxide in slags. In this work, the activity of the oxide in silica saturated iron silicate slags has been measured at 1573 K using the equilibrium Sn (alloy) + Y2O2-SnO (slag).Slag and a Ag-Sn alloy were sealed in a zirconium oxide crucible to prevent the escape of volatile tin oxide, and the oxygen pressure at equilibrium measured in situ using the zirconium oxide as a solid electrolyte. Activity of tin was calculated from known data for the Ag-Sn system and activity of tin oxide calculated from free energy data. The results have been extrapolated to predict the industrially important distribution of tin and iron between Fe-Sn alloy and iron silicate based slags.

Jan 1, 1983

By J D. Grobler

In the heavy minerals industry wet high intensity magnetic separators (WHIMS) are widely applied for primary magnetic separation of magnetic minerals and non-magnetic minerals. This piece of equipment is well known for its robustness to handle a wide range of feed conditions and still produce stable product qualities and yields. A heavy mineral production plant aimed to increase production through their WHIMS plant containing 11 duties and 26 units. Instead of adding new units an alternative approach was followed to firstly maximise the efficiency of the current circuit and secondly to consider possible reconfiguration of the circuit to produce additional product tons for minimal capital investment. In order to characterise the current circuit’s efficiency, identify pockets of excellence and determine the areas for improvement the whole circuit was surveyed several times and mineral mass balances were drawn up.This paper aims to: discuss the modelling process of the WHIMS circuit,explain the calibration and validation process followed to ensure the accuracy, anddemonstrate the sensitivity analysis performed on the different options. From this analysis an efficiency criteria was developed to compare different circuit configurations that enabled the production plant personnel to make an informed decision on the way forward.

Oct 5, 2011