Search Documents

By Earl T. Hayes, W. M. Sternberg, F. P. Williams

"INTRODUCTION The limited domestic demands for lithium salts and metal before the war were met readily by the use of minerals particularly lepidolite (lithium mica) and amblygonite (a lithium phosphate), from which lithium can be recovered relatively easily. New wartime uses, however, created such a demand that it became necessary to turn to spodumene (a lithium feldspar) as the principal source of supply. Although very large deposits of spodumene occur in South Dakota and in North Carolina, it much more difficult to extract lithium from spodumene than from lepidolite or amblygonite.During the spring and summer of 1942 a study was made in Salt Lake City laboratory of the Bureau of Mines on the recovery of lithium from spodumede. Preliminary tests were made on two processes - roasting with potassium sulfate 4/ 5/ and roasting with calcium chloride and calcium carbonate 6/ -,which appeared to be the most promising of the various processes that had been proposed. By roasting spodumene with approximately its own weight of potassium sulfate at 1,050º C. and leaching the product with water, about 70 percent of the lithium could be extracted. Consumption of the relatively expensive potassium sulfate, however, was high; much of the potassium was found in the insoluble leach residue, end large amounts were lost by volatilization and dusting. By roasting the spodumene with calcium chloride and calcium carbonate, nearly 90 percent of the lithium was chloridized temperatures of 850° to 1,050° C. Much of the lithium could be extracted from the calcine by leaching with water after roasting at the lower temperatures, but volatilization of lithium chloride was appreciable, amounting to 20 to 25 percent in a direct gas-fired furnace at temperatures of 800° to 850° C. At 1,000° to 1,050° C., volatilization was far from complete. Thus, it would be necessary to use both fume collection and leaching of the calcine, unless the roasting temperatures were sufficiently high to volatilize all the lithium chloride. Because of the well-known difficulties of collecting chloride fumes, it was decided to search for a better process."

Mar 1, 1946

By M. Somppi, Z. Yamak

"Gold producers invest significant effort in mining, processing, and creating an intermediate gold doré product. Nonetheless, equal effort should be extended to the final handling and processing of the doré bar, and managing the high-purity gold produced at the fine-gold toll refiner. This detailed attention to bullion handling and refining provides rigor and confidence that the mine site is achieving, through fair and controlled methodology, the most appropriate value for the final product. With the above in mind, the following study explores the importance of preparing a set of site best-practices for bullion handling and specifically, detailing the peculiarities of sampling methodologies and the impact on assays.INTRODUCTION Gold and silver handling practices are common place at mine sites and refineries. The practices include but are not limited to smelting, ingot casting, weighing practices, and secure transportation. Proper handling and processing of the bullion material ensures that the mine site is achieving the true value of the final product. Various handling aspects can critically impact the perceived value of the bullion. A few of these particulars include weight tracking, scale recertification and calibration, refining and melting practices, melt temperature measurement, sampling, pouring, bar cleaning, furnace technology and crucible selection, and assaying. Nevertheless, this report discusses and focuses on the importance of proper sampling and molten-metal temperature measurement and their potential impact on the final doré bar value. Refining or re-melting operations achieve a proper measure of the precious metal content of its bullion when the sample accurately represents the whole bar. At first this task appears seemly straightforward, however, taking a representative sample can be challenging and is also one of the most important tasks for valuing gold during the settlement stage at the precious metal refinery. Various bullion sampling methodologies exist; including: dip sampling, granulation, drilling, cutting, and vacuum pin sampling. The Royal Canadian Mint (2009) indicated in their technical review of refinery operations that pin sampling is one of the best methods for cases where representative sampling and accuracy are required, e.g. to determine the payable metal content. Pin sampling consists of inserting a sealed glass vacuum tube (Figure 1) into the molten metal; when the molten metal contacts a purposely-designed weak portion of the glass, the seal breaks and the metal is suctioned into the hollow centre (Figure 2)."

Jan 1, 2018

By Thornton L. Neathery

Geologic investigation of a mineralized zone in eastern Alabama indicates that large quantities of talc and soapstone are scattered over a wide area close to the surface. Laboratory experiments show that this material may be upgraded to a high-quality talc. A market survey indicates that the talc deposits may be of current and long-range interest. The anthophyllite asbestos which is associated with the talc does not appear to occur in sufficient quantities to be considered as a primary commercial source.

Jan 1, 1967

By André Pomerleau, Michel Grégoire, René del Villar

"The operation of industrial flotation columns requires the control of at least two variables, the interface position and the bias rate, by manipulation of some appropriate operating variables. Problems arise due to the reliability of existing methods of measuring the bias (i.e bias = tailings water - feed water), a situation which has often forced the industry to disregard this control loop. Moreover, when using such a measuring approach, the identification of the process dynamics is impossible. A second problem arises from the possible interaction between both control loops that might call for the use of a more complex multivariable control strategy.Recent work done at Lava1 University has demonstrated the feasibility of an independent sensor for bias, which models the relation between the conductivity profile across the interface and the bias value using a neural network algorithm. A 250 cm height, 5.25 cm diameter Plexiglas laboratory column was equipped with a series of conductivity electrodes in its uppermost part (across the interface) to measure both interface position and bias rate. Using such equipment, the flotation column dynamics were identified. The results thus obtained permitted the design and implementation of a distributed PI control strategy, where bias was associated to wash water rate and froth depth to tails rate. Both PI controllers were tuned using a frequency-response tuning method. Results of both identification and process control are presented and discussed.INTRODUCTIONFlotation columns are used for the separation of valuable minerals from a carrier gangue. Typically, this device is a tall (9 to 14 m height) cylinder (1 to 3 m in diameter) although other cross sectional shapes are also used. Finely ground ore is fed as a pulp at about 2 m from the top of the column, and pressurized air is introduced through a sparger at the bottom. If the pulp has been properly conditioned with adequate chemical reagents (collectors and modifiers), the valuable mineral particles falling by gravity will attach themselves to the rising air bubbles, and the air-particle aggregates will rise to the top of the column where they overflow as a stream called the concentrate. The gangue particles,, that do not attach to the air bubbles, fall down the column being withdrawn at its bottom in a stream called the tails.A particular characteristic of flotation columns is the addition of a fine spray of water at the top. As the water flows down through the froth zone, it washes out the entrained gangue particles from the mineralized bubbles, thus improving the quality of the concentrate recovered at the top. As a result of its cleaning action, this water stream is called the wash water and the upper zone, the cleaning zone. In order to ensure a downward flow of wash water, a proper water balance must be kept in the froth zone, otherwise the water added at the top might shortcircuit to the concentrate without performing any cleaning action. This net downward flow of water inside the froth zone is called the bias and represents an important operating variable of a flotation column."

Jan 1, 1999

By David A. Benjamin

In 1986, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied part of the 24,600-acre Orejana Canyon Wilderness Study Area (OR-001-078), in order to evaluate its identified mineral resources. The study area, located in Harney County, 76 mi northeast of Lakeview, OR, is underlain by Miocene basalt, rhyolite flows, tuffs, and tuffaceous sedimentary rocks. No mines, prospects, or claims were found within the study area. According to the U.S. Bureau of Land Management, the tuffaceous rocks have a moderate favorability for the occurrence of diatomite and a low favorability for zeolite resources. Also, the rhyolite flows have a low favorability for the occurrence of perlite resources. However, U.S. Bureau of Mines' studies indicate that no metallic or nonmetallic resources are present in the study area.

Jan 1, 1987

By Zay Jeffries

OF the new production of non-ferrous metals in 1930 gold will rank first in value. We usually think of copper as the most important non-ferrous metal. The copper industry as a whole, that is, adding copper production to copper fabrication, is the largest non-ferrous metal industry. Prior to the world war; however, gold led in value of new metal produced. During the war copper passed gold in value, but gold regained its position during the 1921 depression. For the past several years copper has again passed gold, but in 1930 gold promises again to regain the lead. The gold producer has at times been called a social parasite, largely because we ' cannot eat or drink gold, or because we cannot use it for clothes or for the construction of buildings. Let us briefly examine this accusation.

Jan 1, 1930

By Robert Thomas

DURING the past 20 years the advantages of reinforced concrete as a substitute for timbering in so-called permanent mine openings have been fully recognized, and its use has become almost general practice in the larger mines. The term "permanent mine openings" is used advisedly and is assumed to embrace such openings as ventilation shafts, material shafts and main hoisting shafts, with their adjacent stations, ore pockets, etc. In the concreting of such openings, the actual cost as compared with that of timbering has been of secondary consideration, the support of large openings, elimination of fire hazards, and prevention of inter-ruptions to production being the primary objectives. The ultimate economy, however, of lining such openings with concrete when they are to remain in use during the entire life of the mine, and especially when they are in bad ground, will seldom be questioned. During this 20-year period there have appeared in engineering publi-cations a number of interesting articles on the use of concrete in mines, nearly always describing some specific project of major proportions, such as the concreting of ore pockets, large stations or main hoisting shafts. Such articles are unquestionably of interest, since the projects require considerable engineering thought, not only in the method of excavating large openings, but in their engineering design as well. Concreting of main hoisting shafts, particularly when this is done with the least possible interruption to production, provides some interesting problems. The concreting of haulage drifts of the dimensions commonly found in mines, on the other hand, soon develops into a routine operation, there-fore it is with some hesitancy that the author attempts to prepare an article on this subject. The writer can recall only one article on the concreting of mine haulageways, although several articles have been written concerning the concreting of tunnels considerably larger in dimensions than those required in general mine practice.

Jan 1, 1936

By Pullen G, Rose M

Continuing Professional Development (CPD) is not just a catch-cry. It is an essential component of every-day life in many professions, including accountancy, law and public administration. Without realising it, many other professions are undertaking CPD activities in an un-structured way, including mining, metallurgy and geology. Examples include Annual and technical conferences of The Institute, Branch-level technical meetings and in-company training and development programmes and technical exchanges. Whilst approaches to date have undoubtedly helped keep the Australian mining industry at the forefront of mining technology, one cannot presume that technological development will stand still. To meet this challenge, human resource development must keep pace, not only to optimize utilization of technological developments, but more importantly to develop firm bases from which new products, processes and technologies can be developed within Australia.

Jan 1, 1989

By H. Walqui

This paper describes operating gains resulting from standardizing operating and maintenance practices to improve the performance of the pebble crushing circuit at he Empire Concentrator. Past efforts have led to improved operating time but no additional throughput gains. New Operating standards and checklists were developed and introduced. The content and frequency of the review process indicators was then changed to take advantage of the new practices resulting in an increased feed rate and availability through the pebble crushing circuit.

Feb 27, 2013

By Rokot M

In a little over three years, Chevron Niugini has built up a team of relatively young, hard working men and women, mostly Papua New Guineans, who spend most of their working days out among people in the Southern Highlands and Gulf Provinces who are directly affected by the Kutubu Petroleum Development Project. These are Land and Community Relations officers, or LACROs. They take on a huge responsibility, not only representing Chevron but also being friend, advisor and negotiator, frequently dispensers of medicines, and agricultural advice and more. When things go well, others get the praise, when things go wrong, LACROs are the martyrs. Just as the geologists who locate the oil, the drillers who find it, the engineers who design the facilities, the construction gangs who build them, the landowners who claim it, and the Government who monitor it, so are the LACROs part of a team.

Jan 1, 1991

By Johne Jesus Mol Peixoto

No modelamento matemático do reator RH, a penetração do gás no líquido na perna de subida é o fator chave para determinar a distribuição do gás injetado e obter uma previsão confiável da taxa de circulação do líquido entre a câmara de vácuo e a panela. Neste trabalho, através de simulações numéricas via CFX, investigou-se o efeito das forças de arrasto, de sustentação, de lubrificação da parede, dispersão turbulenta e de massa virtual. A distribuição do gás na perna de subida e os valores de taxa de circulação previstos via CFX foram validados com resultados de modelo físico. A melhor predição da penetração do gás e da taxa de circulação foi obtida na simulação com incorporação da força de massa virtual e da força de sustentação, cujos coeficientes foram iguais a 0,3 e 0,1, respectivamente. A força de lubrificação deve ser utilizada para evitar o acúmulo de gás próximo às paredes da perna, mas possui efeito desprezível sobre a taxa de circulação. Os resultados dos modelos físico e matemático se ajustaram com a equação de Kuwabara para taxa de circulação.

Oct 30, 2017

By S. Lohmeier, D. Gallhofer, B. G. Lottermoser

Reprocessing of historic gold tailings is a common activity in South Africa, while base metal tailings offer similar reprocessing potential. The historic base metal tailings of the Namib Pb–Zn mine (Erongo Region, Namibia) still contain valuable resources of Pb and Zn in carbonate-rich matter. Micro-analysis of primary ore minerals identifies some galena as argentiferous and sphalerite as the principal host of Cd. This study demonstrates that knowledge of primary ore mineralogy helps to reveal the hosts of valuable commodities (Ag, Cd) and that field-portable X-ray fluorescence tools allow precise and accurate determinations of major and minor elements like Zn and Cd in such carbonate-rich material. Although there are limitations to directly determine the contents of certain element (i.e., As, Sb, In), linear correlations allow prediction of the likely abundance of these elements. Providing that the inter-mineral and inter-element relations are understood and there is consistency in sampling and analytical methodology, portable X-ray fluorescence analysis is an effective method to evaluate the chemical characteristics of base metal tailings for a range of major and trace elements.

Sep 9, 2024

By Ana Carolina Ribeiro Duarte

A combinação de propriedades apresentada pelos aços perlíticos permite sua aplicação em diversos segmentos. O objetivo deste trabalho foi caracterizar a microestrutura do aço SAE 1070 deformado via trefilação para a fabricação de fiomáquina. O aço foi trefilado a seco por 12 passes com reduções médias entre 15 e 21%. A caracterização microestrutural foi realizada com o auxílio da técnica de microscopia eletrônica de varredura e microscopia de força atômica. O material teve ainda seu comportamento mecânico avaliado por meio de ensaio de dureza Vickers e ensaio de tração. O material deformado apresentou a estrutura “curling” na seção transversal, enquanto que na seção longitudinal a maioria das lamelas se encontrava alinhadas com a direção de trefilação. Os ensaios de tração e dureza revelaram um aumento considerável da dureza e resistência do material após o processo de trefilação.

Aug 16, 2017

By Alisson Rodrigo dos Santos

O presente trabalho objetiva analisar a viabilidade técnica de recuperar parte do pó de balão, composto por finos de carvão e hematita, submetido primeiramente a tratamento termoquímico e posteriormente a campo magnético uniforme. Foram analisadas amostras oriundas de pó de balão de alto forno funcionando com carvão mineral e alto forno com carvão vegetal. Os finos de carvão, recuperados na separação magnética, podem ser utilizados na sinterização, pelotização e até mesmo reinjetados nas ventaneiras. Essa reutilização tem um efeito muito importante, pois cada tonelada de fino carregado pela ventaneira corresponde a uma economia de carvão que não será carregado pelo topo, deixando mais volume útil livre para a carga de minério. O pó de balão foi submetido a um processo de redução da hematita em magnetita, em atmosfera adequada para a preservação de carbono, a fim de aumentar a susceptibilidade magnética e permitir a separação magnética. Os finos de minério residuais da recuperação dos finos de carvão não são perdidos, podem ser utilizados na fabricação de briquetes ou reutilizado na sinterização e pelotização. Após a redução, o material foi submetido à separação magnética, mostrando-se assim viável tecnicamente a separação e reaproveitamento dos finos de carvão e minério.

Oct 30, 2017

By Martin H. Stanczyk

Bench scale, laboratory batch attrition grinding tests were made of a coarse commercial kaolin in a stainless steel, 5-inch-diameter attrition grinding machine to study the effect of a number of basic operating variables on particle size reduction and electric energy consumption. The results of the investigation showed that the more important operating variables influencing the efficiency of kaolin comminution and energy consumption requirements were type, size, and shape of grinding media, grinding media to clay weight ratio, peripheral rotor speed, clay slip pulp density, degree of pulp dispersion, and the angular arrangement of the rotor and stator bars. The tests also indicated that variables having less influence on grinding efficiency and energy consumption were pulp temperature, design of rotor cage, rotor clearance, rotor-stator bar interval, addition agents, pulp level, degree of pulp aeration, and chamber liners. The research showed that grinding media had the greatest influence on abrasion of machine parts and that spherical-shaped grinding media were superior to sharp angular or long bladed media with respect to media degradation, machine abrasion as well as grinding efficiency.

Jan 1, 1968

By Wilbert J. Huff

This is the sixth of a series of annual reports describing the work of the Explosives Division, Bureau of Mines, United States Department of the Interior.3/ It deals particularly with the activities of the division from July 1, 1940 to June 30, 1941. The studies outlined in this and preceding reports of the series have been conducted under the direction of the author and the respective unit leaders, to whom specific credit is given.

Jan 1, 1942

By A. C. Fieldner

THE COMMITTEE on Correlation of Research held two meetings in 1931. The first was a luncheon meeting on Feb. 19, at the Engineers Club, New York, attended by eight members and four guests-William H. Bassett, past-president of the Institute; Robert E. Tally, president; H. Foster Bain, secretary; and Alfred D. Flinn, director of the Engineering Foundation. Mr. Bassett gave a short resume of the circumstances leading to the formation of the Committee and expressed his opinion that the objectives as expressed by the Committee in its first annual report were in accordance with the ideas of the Institute officials. Mr. Tally stressed the great importance of research in the mining and metallurgical industries and stated that lie believed the Institute should encourage and promote research, and that this Committee could do a great deal to foster such work in the Institute. Mr. Bain pointed out that this Committee was appointed with a view to correlating and fostering research work. in the field of the Institute's activities. This could be done in various ways, as by encouraging the divisions and committees of the Institute to hold group meetings on research, by forming research subcommittees in the Institute divisions, and by bringing together research interest in. certain projects and the fund or organization that is equipped to carry out the project.

Jan 1, 1932

By Eugene McAuliffe

AS anthracite is no longer used to a marked extent by the rail- ways of the United States (1,513,000 tons in 1933), that portion of the mining industry engaged in the production of bituminous coal is, and will continue to be, the one chiefly concerned with the future use of its product by the railways. In a period such as the present, when all enter- prise is unsettled, when fundamental principles of industrial management and control are being swept aside or else changed overnight, it is difficult to predict what will happen. The relation between the total production of bituminous coal and the volume consumed by the steam rail- ways of the United States, Classes I,

Jan 1, 1936

By C. A. Jeffrey, K. Pearson

Abstract - The Croft diorite in central England belongs to a suite of Caledonian igneous rocks collectively known as the South Leicestershire diorite complex. Although the intrusions occupy separate outcrops, they are linked at depth to form a single pluton, buried beneath a cover of Triassic sediments (Le Bas, 1972; 1982, Allsop and Arthur, 1983). Both the Caledonian diorites and the overlying sub-Triassic unconformity have been affected by a complex history of alteration and mineralization which can be subdivided into four stages: (1) deuteric effects, caused by the release of volatiles during magmatic cooling; (2) albitization through sodic enrichment; (3) formation of lowtemperature laumontite, analcime and calcite veins with associated wall-rock alteration to prehnite and pumpellyite; and (4) sub-Triassic unconformity-hosted base metal, manganese and palygorskite mineralization. Zeolite mineralization occured some 200 Ma later than the intrusion itself, during post-Triassic times, as indicated by the presence of a single vein of laumontite and microcrystalline calcite which cross-cuts the sub-Triassic unconformity surface and enters the overlying Triassic sediments. Evidence from fluid inclusion work indicates that two fluids were involved in the deposition of the zeolite veins. One fluid was initially of relatively high temperature (~100°C to 320°C) and low salinity (~0.2 to 5.9 wt% NaCl equiv.), and was probably meteoric in origin, whereas the other was of relatively low temperature (~41°C to 165°C) and high salinity (~0.4 to 16.72 wt% NaCl equiv.), and is interpreted to represent a basinal brine. During Triassic rifting, thinning and fracturing of the crust, with the possible rise of associated magmas (Halliday and Mitchell, 1984), could have increased permeability and heat flow, initiating the circulation of hydrothermal fluids. Triassic unconformity-hosted base-metal mineralization in Central England is similar to other Triassic-Jurassic mineralization in Europe (Mitchell and Halliday, 1976).

Jan 1, 1997

By Rick Frechette, Bryan Ulrich

Representatives from several mining operations in three western states left their mines behind for a day in February to discuss with their peers the issue of water. The event was Knight Piésold and Co.’s Roundtable 2007, held in Elko, NV. It was third such event put on by the company. The issue this year was site-wide water considerations.

Jan 1, 2007