Search Documents

By J. F. T. Agapito, G. P. Bratton

A 16 m by 4.7 m by 24.5 m (52 ft by 15.5 ft by 80.5 ft) underground ore bin was constructed at an 810 m (2660 ft) overburden depth in poor quality, faulted and altered intrusive rocks at Molycorp's block caving molybdenum mine. Geological engineering incorporated detailed structural mapping, rock quality classification, in-situ stress field determinations, numerical stress and failure analysis, and convergence monitoring. The ore bin was mined by conventional methods from the top down and utilized a bored raise for mucking. The initial ground support of rock bolts, lightweight steel sets, and reinforced concrete was later supplemented with an array of 6, 12 and 21 m tensioned, grouted rock bolts when wall closure was noted in the upper ore bin area. The supplementary support was optimized by computer analysis and monitoring.

Jan 1, 1985

By Paul M. Price

The Mouat mine, Nye, Mont., was reopened in 1953 by the American Chrome Co. under a Defense Minerals Production Administration contract. Operations were terminated in 1961 after completion of the contract. Mining methods employed during this period are described in detail, and cost data are presented by years for 1953 through 1959. Ultramafic rocks of the Stillwater complex in Montana contain the largest domestic resource of chromite, and the Mouat mine has been the largest producer. Mine reserves were estimated in 1960 to be about 4.4 million tons containing 22.5 percent Cr203. The chromite deposits occur as a series of overlapping bands or lenses roughly paralleling the steeply dipping layers of the complex. Only two of the chromite layers have proven to be of economic importance. One layer is 2 to 1.6 feet wide; the other is 3 to 8 feet wide. Shrinkage stoping was generally used throughout the mine, but various methods of ore breaking, scope drawing, chute construction, etc., were tested to improve output and lower costs. Long-hole stoping proved to have limited use. Breasting down benches, developed outward from the center of the stope with air-leg drills, was satisfactory only in wider scopes. At the close of operations, the company had standardized the use of lightweight stopers to advance a flat back by breaking from a centrally located face. Mining costs were reduced 47 percent during 7 years of operation.

Jan 1, 1963

By William T. Boyd

Foreign mining publications describing successful hydraulic mining installations, and successful domestic hydraulic mining in a gilsonite bed, have prompted the Federal Bureau of Mines to conduct a literature survey of foreign publications to determine if the hydraulic mining method can be applied to domestic coal mining. Most foreign publications do not give detailed data about the water pressures, water capacities, and production and manpower requirements for successful hydraulic mining, However, they do provide enough general data on mining conditions, manpower, and equipment used to show that conditions in many bituminous coal deposits in the United States may be favorable for economical coal extraction, using high-pressure water jets. Therefore, the Bureau proposes to conduct a field investigation to determine the most appropriate natural conditions, water pressures, and equipment for successful hydraulic mining of coal beds in the United States with variable dip, thickness, and hardness. In the past, technical personnel reviewing foreign mining reports assumed that a steeply pitching coal bed was necessary for successful hydraulic mining. Although the structure of the coal bed may be a factor in gaining assistance from overburden pressures or help in an integrated hydraulic mining and transportation system, the coal is broken mainly by the action of high-pressure, water-penetrating cracks, fissures, or cleats; therefore, the slope of the coal bed is not necessarily a determining factor in hydraulic mining.

Jan 1, 1959

By N Elith

The explosives demolition of a post-stressed, steel reinforced, concrete road bridge in Australia’s capital city, Canberra. The bridge was 50 m from the new replacement bridge, 320 m from community structures and within five kilometres of the national parliament buildings. The job required multiple overlays of risk assessment, public relations, safe work procedures, specialised blast design, environmental predictions and flyrock controls. Project stakeholders included Worksafe, Roads ACT, bridge owners, consulting structural engineers, community groups and road users. The bridge precincts, including a major road underneath, had to remain operational to peak traffic in the days leading up to the demolition. The break-up and removal of debris had to be executed in just two days from Friday to have the road beneath re-opened for Monday morning city-bound traffic.In Canberra, all explosives demolitions are now viewed with particular caution after a demolition in 1997, during which a young girl was killed. Any approval requires that Explosives Regulations, AS2187 2006 and Worksafe processes are satisfied, and a convincing case presented for blasting as a safe and viable option.Our design used specialised shaped cutting and blasting charges to sever in situ concrete beams and tendons and to shatter components of the stressed concrete bridge assembly. We include comments on structural engineering reports dealing with pre-weakening mechanisms. The benefit of pre-weakening is that it reduces the amount of explosives needed to safely complete the job and facilitates quick removal of debris after the shot. The complementary skills of the team, each one an expert in his field, resulted in a highly successful demolition, praised by authorities as an outstanding example of controlled use of explosives.

Nov 8, 2011

By Merwin H. Howes

In constructing the NORAD Combat Operations Center, controlled blasting techniques were employed to achieve smooth walls and to avoid shattering the rock beyond excavation lines. Extraordinary measures were taken to stabilize the rock to permanently preserve the openings. Rock stabilization was accomplished by means of reinforced concrete and gunite linings, rock boltings, installation of chain-link fabric, and epoxy resin and cement grouting. A particular zone of weakness at a vital location was supported by exceptionally thick reinforced concrete lining, rock bolts, and cement grout.

Jan 1, 1966

A new horizontal borehole packer for use in coal beds has been developed. This packer utilizes a principal of operation which has not previously been used. The resulting packer is less costly to purchase, can be easily repaired in the field with inexpensive expendable parts. This report describes the development and testing of the new packer and the evaluation of commercially available packers.

Jan 1, 1971

By C. H. Schack

Although viscosity is known to be important in processing and handling finely ground urea, its effect has never been fully quantified. This report describes the methods used and the results obtained in the initial phases of a broad investigation of the influence of viscosity of water suspensions of minerals in flotation, thickening, filtering, and other mineral-dressing unit operations. Several types of vis-cosimeters were tested before reliable and reproducible results could be obtained on mineral suspensions. After the viscosimeter used in the research was calibrated and standardized, tests were made on six pure minerals to study the relationship of pulp density, particle size, crystallinity, and cleavage on viscosity. An orifice-type viscosimeter equipped with a mechanical stirrer gave as good results as other types and was more flexible, faster, and simpler to operate. The orifice-type viscosimeter, when calibrated and standardized with glycerin and water mixtures, proved satisfactory over a wide range of viscosities. The accuracy and reproducibility were reasonably constant between 1 centipoise and 200 centipoises, the anticipated range in common mineral-dressing unit operations.

Jan 1, 1957

By Daniel Bicalho Viegas

Chapa de desgaste revestida com metal duro tem ampla aplicação na indústria, principalmente no segmento de mineração. Usualmente, o revestimento é aplicado em chapas de aço de baixo carbono. Estes aços são os mais comuns devido à sua boa soldabilidade. Paralelamente ao emprego das chapas revestidas, foi desenvolvido um aço de baixo carbono e de elevada dureza (350 a 600HB), com a finalidade de se tornar uma boa opção como chapa de desgaste. Em função da escassez de informações técnicas quanto à aplicação de revestimento em chapas de alta dureza, este trabalho tem como objetivo avaliar a influência do ciclo térmico de soldagem sobre as propriedades mecânicas do aço Hardox® 450. A metodologia experimental consistiu no revestimento do aço Hardox® 450, com dureza da ordem de 450HB. Para o revestimento foi utilizado o processo de soldagem FCAW. Após a soldagem, foi feita análise do perfil de dureza na seção transversal dos corpos de prova. Para avaliação da resistência ao desgaste, foi feito o ensaio de abrasão conforme recomendações da norma ASTM G65-04. De acordo com os resultados obtidos foi possível confirmar que a aplicação do revestimento duro influencia diretamente nas propriedades mecânicas do material.

Aug 17, 2017

By Anthony H. Tawil

Modern, high-speed machines used in the manufacture of paper require foundations with stringent settlement constraints. To fulfill this requirement, caisson piles, extending into bedrock, were selected to support a paper machine in Baie Comeau for the Quebec North Shore Paper Company (QNSPCo.). This was the fourth machine in an existing paper mill, and its construction was part of an expansion program which included the building of associated structures such as a wood room and chip storage building, and other facilities, Figure 1. The paper mill in Baie Comeau, Quebec, is located in an area which has extensive deposits of sensitive marine clay which are transformed into a viscous liquid when disturbed by external forces such as the driving of piles. Loss of ground and soil disturbance as affected by piling activity assumed considerable importance in the design and construction of the caissons particularly in view of the proximity of existing plant facilities, including another paper machine.

Jan 1, 1987

By Keith A. Heasley, John L. Ellenberger, Paul W. Jeran

In this paper, a state-of-the-art, three-dimensional, full waveform, microseismic system was used to analyze the rock failure around a deep (> 750 m (2500 ft) of cover) bump-prone longwall panel. The microseismic system consisted of both underground and surface geophones coupled through radio telemetry and a fiber-optic network to produce pseudo real-time detection and location of seismic events surrounding the coal seam. This was the first microseismic installation of this scope at a U.S. coal mine, and the system was intended to help determine the exact strata mechanics associated with the redistribution of stress and the associated gob formation at one of the U.S.’s deepest longwall mines. Overall, 5,000 calibrated seismic events were recorded during the mining of one panel, including a Richter magnitude 4.2 event which occurred inside of the array. Analysis of these events provides a number of notable insights into the rock mass behavior. For instance, the longwall panel was widened during the retreat process, and the mining-induced seismicity shows a distinctly different behavior between the start of the panel, the mining of the narrow part of the panel and the mining of the wider part of the panel. Also, in itself, the acquisition of the ML 4.2 event was a major milestone in geomechanical and bump research. This is the first time that such an event has been recorded with this detail and accuracy at a bump-prone coal mine in the U.S. The analysis of this single event has set distinct new limits on the relationship between mining seismicity and coal bumps.

By J. J. Shields

This study by the Federal Bureau of Mines concerns different methods of face haulage used with various types of continuous-mining machines, mobile-loading machines, and track-mounted equipment under varying roof and bottom conditions and in coalbeds of varying thicknesses. This report is the ninth in a series on mechanical mining in bituminous coal mines. Reference to the reports previously published is made in appendix III, p. 106. Use of modern mining equipment in bituminous coal mines has resulted in increased productivity at the face. This especially is true where continuous-mining machines are used, and the supervision is good. Previous methods and equipment for moving coal from the face became inadequate and had to be improved to restore balance to the mining systems. Sometimes new equipment was needed to improve the face haulage, and in some instances, a new combination of existing equipment was used. Detailed studies of face haulage methods were made at 13 mines in Pennsylvania, West Virginia, Ohio, and Illinois to compare their effectiveness and to describe fully the conditions under which each method was used.

Jan 1, 1960

By Charles C. Boley

Using bench-and pilot-scale coking facilities, the Bureau of Mines produced experimental coke from blends of char with Sunnyside coal (high-volatile A bituminous) from Carbon County, Utah. At bench scale, additions of char made from lignite improved resultant cokes when concentrations of up to 60 pct were used in the blends. At pilot scale (500-pound movable-wall oven), four chars made by entrained-bed carbonization techniques from the parent Sunnyside coal and from a North Dakota lignite were used in two-component blends with the Sunnsyide coal. Chars from Sunnyside coal had volatile matter contents of 5.8, 9.8, and 16.0 pct, moisture-free basis; the char from the lignite had 16.6 pct. In twenty-five 500-pound tests, improvement in coke quality was observed from all blends at char concentrations to 17.5 pct. The best coke, produced from a concentration of 12.5 to 15 pct of S.8-pct volatile char, exhibited physical properties approaching those of an industrial coke produced from Sunnyside coal blended with three higher rank blending coals. Studies were also made of the effects on coke quality of char source, of particle size, of comparative use of char and of a blending coal, and of prolonged coal storage.

Jan 1, 1973

By Fred D. Gustafson

With the postwar emergency for new housing and for new industrial buildings, much research has been done on lightweight aggregates for use in concrete and plaster. The trend toward lighter weight aggregates to relieve the dead load on the higher, steel frame- work buildings started toward the end of the last century. Progressively the requirements be- came more stringent, crushed bank slag, weighing 80 lb per cu ft as com- pared to 100 lb for crushed rock, was supplemented in some sections by foamed slags and expanded shales weighing from 40 to 60 lb per cu ft. In other sections cinders were used weighing from 40 to 50 lb, including sand. Sections favored with more recent vulcanism turned to pumice weighing from 30 to 60 lb, whereas other localities made use of diatomite, from 28 to 40 lb. Exfoliated vermiculite weighing from only 6 to 10 lb per cu ft came into use. As the search for lighter weights in aggregates continued so did the search for other desirable properties such as nailability, ease of cutting or channeling, and good insulation to both sound and heat. This search eventually led to a widespread interest in the expansion of perlite, or similar volcanic glasses, with the result that in 1946, the Office of the Housing Expediter' listed eleven firms reporting the operation of processing plants either on pilot or commercial scale producing aggregates weighing from 2 to 16 lb per cu ft.

Jan 1, 1949

By J. R. Allsup

Air pollutants in exhaust gas produced from LP-gas (propane) were studied using both laboratory engines and vehicles. The objective of the study was to evaluate engine parameters relating to the advantageous use of propane as a low-pollution fuel. Some comparisons are made between gasoline, natural gas, and propane. Results show that engines can operate over a wider range of A/F with minimum carbon monoxide and hydrocarbon emission when using propane than when using gasoline. Mixture enrichment using propane is unnecessary during cold starts, thereby eliminating the emission penalty during warmup. Carbon monoxide and hydrocarbon emission using propane are unaffected by ambient temperature. The photochemical reactivity of hydrocarbon emission is considerably lower with propane than with gasoline.

Jan 1, 1972

By William T. Reid

Low-temperature carbonization of coal in Japan served as an important source of liquid fuels during the war. Six plants operating in Japan Proper produced 203,069 KL (53.7 million gallons) of liquid fuel from 1940 until the end of the war in August 1945, while four additional plants in Karafuto and Korea produced 211,943 KL (56.0 million gallons) for a total of 415,012 KL (109.7 million gallons) of liquid products. Semicoke produced in these plants was used for domestic fuel, for gasi- fication in portable gas producers on automotive vehicles, and to replace imported low-volatile bituminous coal in the manufacture of metallurgical coke. Since 1936 one plant had produced more than 300,000 metric tons of semicoke for blending with bituminous coal to form coke, while the total production of semicoke since the beginning of the industry in 1923 is approxi- mately 2,000,000 metric tons. Despite an apparent annual carbonizing capacity of about 2,000,000 metric tons of coal for the entire country, the maximum amount of scmicoke produced during the peak year, 1943, was 468,446 metric tons. The equipment used is primarily of Gorman design. Just before the end of the war, 6 plants using 20 Lurgi carbonizers were operating with a total rated capacity of more than 1,500,000 metric tons of coal per year, while 2 Koppors units had a combined annual rated capacity of 400,000 metric tons of coal. One plant using the Japanese-designed Mimura system was in service but with so much mechanical trouble that its output was small, while in another plant 4 Wanisht carbonizers of Japanese design but based on an early German development were running satisfactorily, and carbonizing about 100,000 metric tons of coal per year. A single installation of 15 American-designed Knowles ovens was operating near Tokyo but was carbonizing pitch for electrode carbon. ..! No true low-temperature process used in Japan could carbonize strongly. caking coals satisfactorily. The Mimura process designed for this purpose was unsuccessful, as was the Shimomura process before it, while the Lurgi, Koppers, and Wanishi systems operated only with noncaking or very weakly caking coals. The Knowles ovens, really a medium-temperature process, could carbonize-caking coal without difficulty...

Feb 1, 1948

By W Liu, S Gao, D Wei, B Cui, Z Guan, Y Shen

Beneficiation of low-grade fine-grained hematite ores becomes increasingly important due to rapid depletion of high quality iron ore resources. However, fine particles, especially ultra-fine particles, make efficient beneficiation of these ores more difficult. Therefore, methods to reduce the influence of fine particles must be considered to achieve better beneficiation performance. Analysis and systematical beneficiation tests were carried out on an ultra-fine-grained hematite ore slime from washing a fine grained hematite ore. Ore particles were found to be presented in loose soil. While some of the ore particles were agglomerated, they were very fine and contained up to 76.5 per cent -0.023 mm material. In this paper, using a single magnetic separation flow sheet with sodium silicate (SS) as a dispersing agent, a concentrate containing 65.05 per cent Fe was obtained at an iron recovery of 68.58 per cent from the hematite ore slime of 56.65 per cent Fe. The single magnetic separation flow sheet was simple and reliable, the agent SS was effective in dispersing ultra-fine particles. The results are believed to be applicable to similar hematite ores.CITATION:Wei, D, Guan, Z, Gao, S, Liu, W, Shen, Y and Cui, B, 2013. Beneficiation study of an ultra-fine-grained hematite ore slime, in Proceedings Iron Ore 2013 , pp 495-500 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By R. D. Rubright, Owen J. Hart

In the Bingham district over a span of more than 90 years, 43,947,104 tons of "non-porphyry" copper, lead, zinc, gold, and silver ore have been mined from a folded and faulted alternating series of Pennsylvanian and Permian limestones and sandstones and from some Tertiary intrusives. This ore came from six major mine areas located east, south, and west of the Bingham stock, site of Kennecott's porphyry copper deposit. The sediments were affected by varying degrees and types of metamorphism within 2000 feet or more of the Bingham stock. The intrusives consisting of the mineralized Bingham and the unmineralized Last Chance stocks and numerous dikes and sills of granite and monzonite were intruded into the asymmetrical northwest-trending and plunging Bingham syncline. Extrusives, although present, contain no ore. The bulk of the non-porphyry ore in the district was found above the Midas thrust. The primary ores are found in three major types of deposits: concordant bedding fissures, crosscutting fissures, and replacement deposits. These deposits consist of both copper and lead-zinc ore bodies that contain various amounts of gold and silver. These are in places roughly zoned both laterally and vertically and have been mined for up to 10,000 feet outward from the center of the Bingham stock and up to 5000 feet vertically below the surface. Secondary ore was of minor importance and was found in and under the oxidized zone at shallow depths. Genetically the Bingham stock, the ores, and related phenomena have had a common source.

Jan 1, 1968

By Arthur W. Cooper

This paper contains a review of the development of blast furnace? slag handling and processing technology in the Ironmaking industry over the past 30 years, with an emphasis on economic and environmental factors. The requirements and practice of air-cooling slag for use as aggregate and of pelletizing and granulating slag for use in cement manufacture are described. The operation of slag pits, slag pots or ladles, the slag pelletizer and early granulation systems are compared with the new continuous .granulation, dewatering and handling systems developed in the past decade.

Jan 1, 1992

By D Craw, S Clearwater, S Hammit, C Smith

Prior to rehabilitation, plant cover on quartz gravel overburden at Wangaloa coal mine was highly patchy. Stabilisation techniques have since considerably altered the condition of the main overburden yet deposits in the east and west remain largely intact. On the eastern overburden, three distinct zones of revegetation have naturally developed: Zone 1 represents a dense plant cover, Zone 2 a patchy cover and Zone 3 a sparse cover of isolated plants. Aerial photographs show much of the eastern overburden was deposited between 1940 and 1960s. Yet we found that the temporal scale of deposition did not wholly account for the differences observed in vegetation development. To investigate other influential factors, we set up 12 study plots using four replicates in each vegetation zone. The diversity and density of plants in each plot were measured to quantify the degree of vegetation development. Samples from the substrate in each plot were collected using soil cores to a depth of 10 cm. Cores were analysed for indicators of nutrient availability, metal content and physical composition. We found that substrate chemistry varied between individual study plots, but showed little difference overall along the vegetation gradient. Substrate physical differences were much greater. The ratio of coarse quartz pebbles: fines was considerably higher in Zone 3 than other zones, and within zones where plants were not growing. Bulk density also increased successively from Zone 1 - 3. We found clear evidence for the reversed stratigraphy of excavation superimposed over the time scale of deposition, and the corresponding nature of fine particles. The rate of revegetation was therefore highly dependent upon the substrate composition of the last surface deposit from the dumping truck. Our data suggests an optimum ratio exists between inert coarse material and a fine matrix for progressive natural vegetation development on mine substrates.

Jan 1, 2004

By A. Moergeli

The Swiss are building the world’s longest tunnel, the 57-Kilometer (35-mile) long Gotthard Base Tunnel. Lot 252, Tunnel Amsteg: Two Hard Rock Tunnel Boring Machines (TBM) crossed hydro-thermally decomposed granite. While the East TBM advanced slowly but steadily, the West one got stuck for five months and had to be recovered by special means and methods. Both TBMs have finished their more than 11-Kilometer (7 miles) long drives successfully. Lot 360, Tunnel Sedrun: For the first time in tunneling, roadway support machines are used through most challenging, squeezing geology. They constantly advance in full face mode for about one Tunnelmeter/24 hours.

Jan 1, 2007